used LÖWER lz

Grinding machine Löwer ESM 300 Built in 1987 Grinding width 290 mm Sanding belt width 300 mm Oscillating abrasive belt Usable height 120 mm Abrasive belt length 1800 mm Table length 1200 mm With support rail Support rail length 3000 mm Feed speed 3/6/12 m/min. Motor power drive motor 7.5 kW Air connection 6 bar Brush unit in the outlet The abrasive belt is guided over three rollers. Between the two lower rollers is the sanding pad. To get a clean cut, the front lower roller has been rubberized. She takes care of the pre-grinding, and the sanding pad behind it the finishing touches. Weight 798 kg with pallet Dimensions with support rail 3000 mm x 1200 mm x H 1700 mm Dimensions without support rail 1300 mm x 950 mm x H 1700 mm

Number of sanding units: 8 st. sanding width: 180 (260) mm Sanding height max.: 160 mm Dimensions (length / width): 3065x1600x1900 mm weight of the machine ca.: 1500 kg Löwer Leistomad SD Window single wood intermediate sanding machine --------------------------------- Machine factory tested by Löwer! Automatic fine grinding machine for wood grinding (smoothing, defibering and Edge breaking) or intermediate sanding of profiled window bars. With soft disc Technology for the visible surfaces as well as automatically safe profile and Width adjustment. - 2 lamella roller units on the side, each 0.37kW, L=100mm, D=200mm - 1 softisc unit Ø=200mm above 0.75kW, - 1 slat roller unit L=200mm above 0.75kW - 1 soft disc unit Ø=200mm below 0.75kW, - 1 lamella roller unit L=200mm below 0.75kW, - 2 lamella roller units on the side, each 0.37kW, L=100mm, D=200mm - Linear guidance of all grinding uni ...

Number of sanding units: 8 st. sanding width: 150 mm Machine can be inspected during production! Leistomat - Finisch and intermediate leveling machine Löwer LZ 8 -------------------------------------------------- ------------------- for finish sanding (smoothing, defibering and edge breaking) or intermediate sanding profiled window latch - Finish and intermediate sanding machine with eight sanding blade aggregates, 2 surface units at the top (synchronism / counter-rotation) 2 surface units below (synchronism / counter-rotation) 4 profile units with angled arrangement top right, bottom right, top left, bottom left, all mating - linear guidance of all grinding units over Linear ball bearing sets on hardened shafts - Timed immersion of all in the opposite direction rotating grinding units directly above the incoming Workpiece edges to avoid looping through the Primer in the front edge area ...

Edge sanding machine make LÖWER type KS 225Machine -No: 1931 built in 1988Technical specifications:Sanding belt width: 150 mmSanding belt length: 2250 mmWork surface: 150 x 800 mmBelt speed: 16 m / sec.Tape roll diameter: 110 mmDrive power: 1.1 kWWeight: 77 kgExternal dimensions approx .: 1300 x 400 x 1000 mmWith- swiveling sanding table- tiltable tableused in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Number of sanding units: 2 St. sanding width: 190 mm Sanding height max.: 2-180 mm LÖWER-Doppelseitige Schleifmaschine DSM 2000 Doppelseitige Einzelholzschleifmaschine zum Schleifen von Massivholz wie z.B. Fensterhölzern etc. Stabile Top-Aus- führung mit langen Gußtischen, Bürst- und Finisheinrichtung und Transportbandvorschub. Geeignet für hohe Dauerbelastung auch bei höheren Spanabnahmen. - versetzt angeordnete Schleif- und Finishaggregate oben und unten - direkt angetriebene gummierte Schleifrollen für schlupffreie Kraftübertragung - Kombischliff über Rolle und Schuh für hohe Spanabnahmen bei gleichzeitig ebener Eingriffszone - wartungs- und verschleißfreie CERMET-beschichtete Schleifschuhe mit sehr guter Wärmeleitfähigkeit und absoluter Maßhaltigkeit - Fremdkühlung der Schleifzonen für einen kühleren Schliff und höhere Schleifbandstandzeiten - zwangsgeführte pneu ...

Working width: 300 mm Number of sanding units: 6 st. Workpiece thickness max.: 8-230 mm Weight: 3100 kg Löwer double-sided grinding machine DSM 3304 GDR --------------------------------- Manufacturer short description: Double-sided single wood sander for sanding of solid wood such as window wood or Furniture components made of MDF etc. Stable top design with electronic articulated pressure shoes for fine grinding well-planed or veneered surfaces. Sanding units arranged one after the other Fine grinding, disc aggregates for defibering grinding, Cleaning brush, from above and below as follows: 1. Belt sanding unit with articulated pressure shoe 2. Belt sanding unit with articulated pressure shoe 3. Disc unit with brush sanding flaps diameter 320mm 4. Cleaning brush with Tempicofibre trim diameter 120mm --------------------------------- detailed long text of the manufacturers description a ...

used Löwer belt sander RSM 2800 SX Grinding width approx. 200 mm Grinding height approx. 120 mm Belt length approx. 1600 mm Belt width approx. 200 mm

Beam Sander Manufacturer: Löwer Model: HBS 400 UB Year: 2012 Sanding width: 390mm Workpiece height: 15-390 mm

Structuring Machine, Brush Grinding Machine Make: Löwer Model: SMN 650 BB Year of construction: 2017 2 grinding shafts

Number of sanding units: 1 st. sanding width: 150 mm Sanding height max.: 150 mm Löwer edge finishing machine MiniSpin N Machines for finishing and intermediate sanding Edges and profiles with a grinding spindle horizontal or vertical. Motor 0.75 KW Spindle in vertical position for processing edges Spindle in horizontal position, swung out to the side for processing longer profile bars or similar or in Connection with a combination grinding head for grinding of edges with a sanding flap disc Grinding head can be swiveled +/- 20° for processing of slanted edges Working height / width 150 mm max. diameter roller / brush < 300 mm Frequency converter for continuous adjustment of the Spindle speed 200 - 800 rpm Table size 400 x 800 mm two directions of rotation selectable Operating voltage 110 / 240 V, 50 / 60 Hz Suction connection D=100 mm Weight approx. 100 kg including grooved base body  ...

Number of sanding units: 4 St. sanding width: 200 mm Sanding height max.: 180 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Number of sanding units: 2 St. sanding width: 290 mm Sanding height max.: 180 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Number of sanding units: 2 st. sanding width: 390 mm Sanding height max.: 390 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Number of sanding units: 2 St sanding width: 190 mm Sanding height max.: 2 - 180 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Number of sanding units: 4 St. sanding width: 200 mm Sanding height max.: 150 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Table dimensions: 1000,400 mm pneumatic clamping: 2 St. moveable: Option For quick pressing of Minizinken- or Soflineverbindungen - Independent of the angle - Particularly suitable for arched manufacturing in window - Table size 1000 x 400 mm - Pneumatic connector 10 bar - Air consumption: 0.5 cdm / stroke - Two clamping cylinders for workpiece clamping - Right half of the table stored on hardened shafts via linear ball bearings - 1 pressure cylinders for linear displacement table - CE - execution (technical data according to manufacturer - without guarantee.!) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Number of sanding units: 8 st. sanding width: 180 (260) mm Sanding height max.: 160 mm Dimensions (L/W/H): 3065x1600x1900 mm weight of the machine ca.: 1300 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Table dimensions: 1000,400 mm pneumatic clamping: 4 St. moveable: Option For fast compression of Minizinken- or Softline compounds especially for larger cross-sections - Independent of the angle - Especially suitable for arched manufacturing - Table size 1000 x 400 mm - Pneumatic connection 10 bar - Air consumption 1 cdm / stroke - 4 clamping cylinders for workpiece clamping - Pairs switchable - Right half of the table supported on hardened shafts through ball linear bearings - 2 pressure cylinder for linear table displacement, separately switchable - Weight: 200 kg - CE - execution (Technical details according to manufacturer - without guarantee.!) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Abrasive belt width 200 mm Grinding width 190 mm Sanding belt length 1600 mm Maximum grinding thickness 120 mm Motor power 5.5 kW Grinding motor speed 2,870 rpm. Abrasive belt speed 1,300 m/min. Oscillating abrasive belt

Frame Sanding Machine Sanding Pad, Oscillation, Frame Sanding Device, Feed Belt, Belt Cleaning ---------- Technical Data ---------- Grinding width: 190 mm, max. workpiece thickness: 120 mm, speed: 6,11,16 m/min., motor: 5.5 kW, weight: 550 kg Sold as is, without technical inspection

Description: Double-sided four-belt single wood sanding machine for sanding solid wood such as window timbers etc. Sanding from above: 1. belt sanding unit with steel roller 2. belt sanding unit with shoe 3. finishing unit with brush Sanding from bottom 1. belt sanding unit with steel roller 2. belt sanding unit with shoe 3. finishing unit with brush  , Technical data - Sanding belt speed 22 m/s - Sanding belt length 1800mm - Sanding belt width 200mm - Working width 190mm - Sanding thickness 2-180mm The roller conveyors and conveyor belts shown are not included in the scope of delivery serial number: 10,434, hollow height: 2 - 180 mm, grinding band dimension: 1800 x 200 mm, packing measure approx (l x w x h): 3,500 x 1,000 x 2,000 mm, Approx. Onsite Dimension. (l x w x h): 3,000 x 1,000 x 2,000 mm, weight approx.: 3,000 kg

year 1985 Capacity 2500 / 2750 Ton 24900 / 27400 kN Speed 65 SPM, continuous mode Ram/Slide Stroke 12.60in, 320.00mm Ram/Slide Adjustment 0.39in, 10.00mm Shut Height (Ram / Slide Down, Adjustment Up) 35.60in, 905.00mm Stroke of Upper Knockout 2.00in, 50.00mm Stroke of Lower Knockout 2.80in, 70.00mm Ram/Slide Width 52.00 in, 1320.00 mm Ram/Slide Height 43.00 in, 1100.00 mm Bed Width 53.00 in, 1340.00 mm Bed Depth 55.00 in, 1400.00 mm power Existing Additional 28 Strokes per minute in manual mode, height shown is above floor, total height is 291 in ( 7390 mm), new quick change hydraulic type bolster Machine Length 160.00 in, 4055.00 mm Machine Width 157.00 in, 4000.00 mm machine height 264.00 in, 6710.00 mm Weight 320000 lbs, 145455 kg Condition Excellent Currently disassembled an ...

SMERAL LZK 2500 Hot Forging press Fully refurbished in 2024* Capacity: 2500 Ton Speed: 65 SPM, continuous mode Ram/Slide Stroke: 320.00mm Ram/Slide Adjustment: 10.00mm Shut Height (Ram/Slide Down, Adjustment Up): 905.00mm Stroke of Upper Knockout: 50.00mm Stroke of Lower Knockout: 70.00mm Ram/Slide Width: 1320.00 mm Ram/Slide Height: 1100.00 mm Bed Width: 1340.00 mm Bed Depth: 1400.00 mm Power: 130kW Machine Length: 4055.00 mm Machine Width: 4000.00 mm Machine Height: 6710.00 mm Weight: 140000 kg Condition: like new * refurbishing report: 1. Mechanical part • Complete disassembly of the press. • Measurement and troubleshooting of all parts. • The main parts of the press are tested (without destruction) in order to identify any defects. Frame: The frame was inspected and non-destructive testing of the most loaded areas was carried out. Damage to the table  ...

Edge grinding machine long fence LZK-5 Oscillating L x W x H: 1100 x 1800 x 1700 mm Weight approx. 400 kg Built in 1981 The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4952 Eriswil/EN-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Mill mat 4 CH-4952 Eriswil/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Key data: 280 mm

Year of construction 2015 Center height: 165 mm Center width: 650 mm Turning diameter over bed: 280 mm Face slide: 180 mm Spindle speed: 30 - 4000 rpm (infinitely variable) Spindle bore: 43 mm Feeds: 0.025 - 0.9 mm/rev Thread pitch: 0.2 - 7 mm Spindle head DIN 55027: Size 5 Bed sledge travel: 610 mm Sledge travel: 165 mm Upper slide travel: 115 mm Inner cone tailstock quill DIN 228: MK3 Quill stroke: 82 mm Dimensions: 1600 x 860 x 1450 mm Weight: 1000 kg Total power requirement: 18kVA Accessories: 3-jaw chuck, Multifix quick-change steel bracket with cassettes, bezel, coolant device, lighting, chip protection