KESSLER dm used machines

Servo motor, electric motor, direct current motor, direct current generator, electric motor with direct current generator -Spare part: comes from a Scharmann boring mill -Manufacturer: Kessler, electric motor with direct current generators -Three-phase motor type: DM21-16 32 kW 2880 rpm -DC Gen. Type: G 50/42/1 6/18 kW -DC Gen. Type: G 44/14/2 8.2 kW -Technical data: see photos nameplates -Dimensions: 1750/580/H540 mm -Weight: 886 kg

Servo motor, electric motor, DC motor, stepper motor, stepper motor, stepping motor -Manufacturer: Kessler, DC motor -Type: GM50/60/1/U -Max. Speed: 3200 rpm -Power: 16 kW -Voltage: see photo nameplate -Shaft: Ø 55 x 100 mm -Construction: B3 -Dimensions: 1010/570/H520 mm -Weight: 610 kg

Servo motor, electric motor, DC motor, stepper motor, stepper motor, stepping motor -Manufacturer: Kessler, DC motor -Type: M30/36/2 -Max. Speed: 3045 rpm -Power: 7.5 kW -Voltage: 170/400 V see photo nameplate -Shaft: Ø 28 x 60 mm -Construction: B3 -Dimensions: 585/290/H340 mm -Weight: 115 kg

Motor potentiometer, regulator, motor controller, rotary potentiometer -Manufacturer: Kessler, motor potentiometer type P3-173 KL -Distortion Plan: PFN-64 -Rotary potentiometer: Rosenthal P 500 19 Ohm / Rosenthal P 100 470 Ohm -Individual components: see photos -Dimensions: 550/200/H270 mm -Weight: 9.1 kg

power capacity: 7,5 Kw volt: 260 V ampere: 32 A total power requirement: kW weight of the machine ca.: 120 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Servo motor, electric motor, DC motor, stepper motor, stepper motor, stepping motor -Manufacturer: Scharmann, DC motor from a Scharmann table boring mill -Power: 3 - 11 kW -Speed: 220 - 3200 rpm -techn. Data: see photo nameplate -Shaft: Ø 45 x 104 mm -Construction: B3 -Dimensions: 1000/550 / H450 mm -Weight: 509 kg

Electric motor, three-phase motor -Power: 3.7 kW -Speed: 1430 rpm -Shaft: Ø 32 x 50 mm -Construction: B3 -Dimensions: 400/295/H350 mm -Weight: 85 kg

Label Printers Industrial Printers Thermal Transfer Direct Thermal Printers 1 x Honeywell Label Printer DMX-A-4212 New from Spare Stock 1 x Honeywell Label Printer DMX-A-6310 New from Spare Stock

Lots of various machine parts for DMG machines 1. 2 x 622 Screw Pump Knoll KTS25-50-T 2. 3 x 2446970 guide X-axis 3. 2 x 2446982 guide Y-axis 4. 2 x 2445009 guide Z-axis 5. 1 x 2452679 Ball Screw X Axis 6. 1 x 27076980 Ball Screw X - Axis 7. 1 x 2468089 Ball Screw Z - Axis 8. 1 x 2468095 Ball Screw Y - Axis 9. 1 x 1530 Deep Groove Ball Bearing Set for DMG Ident No.: 2458918 10. 2 x 10222470 tool gripper 11. 2 x 10220231 tool gripper finger 12. 1 x 28840410100500Ball Screw Z - Axis 13. 1 x 2884041010040Ball Screw X - Axis 14. 1 x 28840410200300Ball Screw Y - Axis 15. 1 x 28830410101600Timing Belt Wheel / Gear 16. 2 x A.1269.1217 Hydac A.1269.1217 hydraulic power unit 17. 2 x 1580 lubrication unit SKF Vogel MFE5

Age 2004, Consisting of:, Base Machine is a OMSO DM44N 2-Lane Lid Machine without the Print Heads and UV-Tunnel, L- Format in feed conveyor for feeding Vertical Lid Stacks, acts as an accumalator as well 2 x Denesting unist each with a Vertical Magazine with Universal Helical Screws with suction Nipples Infeed conveyor with Vacuum to keep Lids in proper position Each Lane with PAGOmat 6HS Label Dispenser, Label dispensers, with PLC Controls manufactured by Fuji Seal, Switzerland Outfeed Conveyor to 2-Lnae Lid Stacker 2-Lane Stacker, each Lane with 2 x Universal Helical Screws Main Drive with a variable frequency, AC-Synchronous Motor with a brake, with Microprocessor Controls Vision System to monitor the Color and positioning of the Labels 400 V, 3 phase, 50 Hz, Max. Lid dimensions: [Round Lids]: Dia. 125 mm, Height: 25 mm. [Rectangular & Oval Lids]: 125 x 150 mm, Height: 25 mm, Single L ...

Total actual Printing hours, only 26,000, Specifications:, Infeed Conveyor for feeding Vertical Lid Stacks, Robotic removal of Lids from stack to Print Unit Conveyor, Auto-Denester Unit, No Lid no Ink and No Lid no Print System, ARCOTEC CG20-2 Pretreatment station, Main 6-Color Print Unit, Speed Control for Ink Fountain Rollers, Printing Roller self-cleaning device, Max. speed 30,000 Lids/ hr (depending on Lid size & shape), Max. Lid dia. Ø 200 mm, Min. Lid dia. Ø 50 mm, Max. Lid Height 25 mm, Max. Rectangular Lid size: 200 x 200 mm, Max. Printing dimensions: 180 x 180 mm, No. of Printing Blankets 4, UV Tunnel TUV 0077-99, UV-Tunnel power rating : 8 kW, Main printer power rating: 20kW, Polytype Counter/ Stacker unit, delivers Counted Vertical Stacks., 400 V 3phase, 50 Hz,, Printing Plate Pre-registration Unit., Max Lid dia: Ø 200 mm, Min Lid dia: Ø 50 mm, Max Lid Height: 25 mm, Max R ...

x-travel: 750 mm y-travel: 560 mm z-travel: 600 mm Control: HEIDENHAIN iTNC 530 total power requirement: 70 kW weight of the machine ca.: 11.000 kg dimensions of the machine ca.: m D E C K E L M A H O (Germany) Vertical CNC Machining Centre with high speed linear drives in 3 Axis and in double column design for high precision work Model DMC 75 V LINEAR Year 2005 _______________________________________________________ Working range: Longitudinal stroke X Axis 750 mm Vertical stroke Z Axis 600 mm Cross stroke Y Axis 560 mm Table clamping size 950 x 650 mm Max. Table load 1.000 kg Max. height of workpiece 600 mm Tool holder Cone HSK 63 Spindle (KESSLER) speeds 18,000 rpm Torque, max. 86/1 ...

Mill Plus Control Built in 1998 24-fold tool changer Working area 500 x 380 x 380 mm Rapid traverses 10000 m/min Rapid traverse 30 m Direct displacement measuring system Tool holder SK40, ISO DIN 69871 max. spindle speed max. 15000 rpm (Kessler) Angle table 800 x 480 mm, load 500 kg Spindle concentricity 300/0.01 mm Weight 3500 kg Machine dimensions: 2.45 x 1.76 x 2.38 m Coolant Injection El. Handwheel The machine is in very good technical condition. Runs quietly and precisely.

530-mm plane width and 4 knife waves quiet run through plane knife waves diameter 125 mms. stable Abrichtanschlag tiltable from 90 ° to 45 ° of highly competitive 5.5 kW of engine S1 . table length 2.9 m Max Spanabnahme, mm 8 Absaugstutzendurchmesser, mm ?160 total weight, kg 800

Qty. 4 Second-hand DC motors Mfc.: ABB Type: DMI400R-DC motor Built: 2009 Power: 1250 kW-815 V-1591 Amps.- 1500 RPM

Heart Angio system in very good technical and optical condition as good as new!

Heart Angio system in very good technical and optical condition as good as new!

BUHLER impacts dehulling machines suitable for oats, sunflower, spelt, soya and some others.. Almost not used since it was in a store Very nice conception , 18 cm impact ring hence hight output till 3 tonnes per hour according to Handbook manufacturer with an integrated diaphram to set the material flow input With an integrated device to set the speed by hand ... but also be set with speed electronical variator Many other Buhler machines available for dehulling lines : scourer MHXF, paddy table .... enquiries welcome Shipping to any destination possible

Bosch DMA 140D 301-D, 1070077623-216 Technical data: 670V-705V140A max. Version: V.0.019 *Original price: 13554,-€ Item condition: Used, in perfect condition More products of this category can be found in our extensive EBAY assortment. More plug-in cards - new and used - can be found in our shop! International shipping costs on request! Plug-in cards and other products buy cheap - Here you buy goods from the professional for the professional - In our SHOP you will find more attractive offers

-X-Way-700mm -Y-way-700mm -Z-way-700mm -Control-ITNC 530 -Spindle holder HSK A63 -Spindle speed-12000rpm -Plate changer with 7 pallets -Tool magasin with 120 -Internal cooling feeder-40bar -Spindle motor-20kW -Pallet size 500x500mm -Machine weight approx.16t -Top condition,to be visited under electricity

Key data: 500 , 520 , 380

Bearing number 1105-02750 Machine Type Machining Center - Universal Make DMG DECKEL-MAHO Type DMU 50 eV / 5 axes Built in 2001 Control type CNC Storage location FRANCE Country of origin Germany Delivery time immediately Freight base EX WORK Technical details x-way 500 mm y-way 420 mm z-way 380 mm Control HEIDENHAIN TNC 430 Spindle cone SK 40 Speeds 18,000 rpm Spindle motor 15 kW Rapid speed 50 m/min Table clamping area 500 per m. x 380 mm Feed range up to 20 000 mm/min Tool change device 32 fold Total power requirement 38 kVA Machine weight approx. 5.9 t Information - CNC - CONTROL of the display of HEIDENHAIN TNC 430 - 5-axis machine with B + C axis - Spindle on: 22 800 h - Current on: 38 000 h - Machine documents spaenefoerderer

320 pieces Multishuttle Dematic DMS2 STATIC Used goods built in 2019, very good condition, see pictures Load capacity: 31.5kg Load types: plastic containers, cartons, trays, containers How it works: Dematic Multishuttle 2 Overview - YouTube Negotiation price: € 2.900,- net ex stock Negotiation price: 1 piece € 5.900,- net/piece from 5 pieces € 4.900,- net/piece from 10 pieces € 3.900,- net/piece from 50 pieces € 2.900,- net/piece Very few hours of operation! Steel construction, rails, etc. available. Dismantling will take place from April to June 2024. Location: Northern Italy. Viewing possible by appointment. Further information on request. Partial sale possible. Systems are professionally dismantled and loaded. Transport and customs clearance can be carried out by us. Assembly and programming can be carried out by partner companies. EVE ...

Control type: CNC Sinumerik 840D-SL x-way 1135 mm y-way 1050 mm z-way 750 mm table size 1400 x 1050 mm Table load 2500 kg max. workpiece size LxWxH 1400 x 1240 x 750 mm Speed 10000 rpm feed speeds X/Y/Z Axis 40000 mm/min Expressspeeds x/y/z 40000 mm/min Tool holder HSK-A100 HSK Number of places in the tool magazine 30 places max. tool weight 20 kg max. tool length 395 mm max. tool diameter 110 mm Machine height 3294 mm Drive power - spindle motor 44 kW machine weight approx. 17.9 t Space requirements approx. 15 m2 Information: Universal milling machine in mono BLOCK design (3-axis) - available September 2019 - only 3800 spindle hours, 13400 power-on hours Equipment / Accessories: - Coolant system - High-pressure pump - Chip conveyor - Hand-held panel - BALLUFF option - Documentation

Semi - Automatic Butter Extruder and Shaping Machine fited on full stainless steel frame, Control panel. Two Stainless steel screw augers, stainless steel hopper. Manufacture : Dairy Machinery UK Model : DMUK EXSH1 Usage : Butter Extruding and Shaping Machine Shapes : Various Shapes and Sizes Condition : New Warranty : 12 months Spare Parts : Dairy Machinery UK

Dairy Mschinery UK now offers new Glass Bottle Fillers for Milk and Juice. We offer machines for Hot fill and Cold Fill. Our bottle capacities are between 1000 - 7000 bottles per hour. Manufacture : Dairy Machinery UK Volume : 500ml - 1000ml Capacity : Option on order between 1000- 7000 bph Capping : 38mm magnetic capping chucks Filling Nozzles : Gravity Filling on Rubbers Lift and Fill or Gravity Filling Drop and Fill Cap : Aluminium Screw Cap CIP : Available Controls : Control panel Standards 2019 Certified : EC certificates Installation : We install all our machines at the clients facilities. Warranty : 12 months Spare Parts : spares@dairymachineryuk.co.uk