GEKA gcs used machines

: 28 min. Punching force: 110 to : 40x20 mm flat steel: 600x15 oder 400x20 mm L-beam 90°: 160x160x16 mm L-beam 45°: 70x70x7 mm : 50 mm square edge steel: 50 mm : 13 mm throat: 300 mm Basic equipment: - Complete set of blades for flat steel shears - Complete knife set for bar cutter - Complete knife set for angle steel shears - Compl. Standard punching device - Stamp quick release device for punches up to 40 mm diameter - Rectangle notch compl. with hold downs - Complete knife set below for rectangular notching - Upper tool for rectangular notching - Support table for flat material - Punching table with stop - Notch with stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

stroke: 70 mm work height max.: 1094 mm throat: 500 mm : 40 in 14 mm no. of strokes: 20 Hub/min throat: 500 mm : 80 to engine output: 9 kW range L-W-H: 1980x1150x2000 mm weight: 2000 kg Accessories / equipment: - punching table The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 32 /min Punching force: 60 to throat: 500 mm : 40x11 mm : 350x15 mm : 350x15 mm L-beam 90°: 120x120x10 mm : 45 mm square edge steel: 40 mm : 10 mm : Aufnahme bis max. 150x10 engine output: 5,5 kW weight: 2012 kg Basic equipment: - Flat steel shears with knife set - Angle shears with knife set - Punch with quick release device for punches up to 40 mm - Support table for punching device - Triangular notching device - Support table for notching - bending station - Bending stamp with matrices V 40 and V 70 - electrical contact stop (1 meter) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 32 /min Punching force: 60 to throat: 250 mm : bis max. Ø 40x11 mm : 350x15 mm : 350x15 mm L-beam 90°: 120x120x10 mm : 45 mm square edge steel: 40 mm : 10 mm : Aufnahme bis max. 150x10 engine output: 5,5 kW weight: ca. 1600 kg Basic equipment: - Flat steel shears with knife set - Angle shears with knife set - Punch with quick release device for punches up to 40 mm - Support table for punching device - Triangular notching device - Support table for notching - bending station - Bending stamp with matrices V 40 and V 70 - electrical contact stop (1 meter) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 110 t : Ø 40x20 mm throat: 500 mm engine output: 9 kW no. of strokes: 28 Hub/min stroke max.: 80 mm weight: 3150 kg Accessories / equipment: - punching table The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 45 to. no. of strokes: 24 Hub/min hole diameter in sheet thickness: max. Ø 27 in 13 mm : 80x80x8 : 60x60x6 mm flat steel: 300x10/200x13 mm : 7 mm engine output: 2.2 kW range L-W-H: 1550x820x1540 mm weight: 760 kg Standard equipment: - Complete knife set for flat steel shears - complete knife set for angle steel shears - complete standard punching equipment - Stamp quick release device for punches up to Ø 27 mm - Rectangular notching device complete with hold-down device - notch - Support table for punching device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Large stock of punching material (dies/stamps), spare parts

Hand - Bending bench Manufacturer: GEKA

Inv. Num. : 7366 Type: Hydracrop 70- SD Producer: GEKA Created: 1993 Parameters: Power consumption: 9 kW Impact neck: 500 mm Machine weight: 2400 kg Dimension: 1300 x 2100 x 1800 mm Equipment: 2 foot pedals

GEKA HYDRACROP 55/S hydraulic ironworker machine built in 2008 in Spain, is a highly versatile and multifunctional machine that allows a wide range of workpiece machining. Its rigid, sturdy structure is equipped with 5 work stations, designed for the precise hole and corner punching, as well as shearing flat bars, angle bars and solid bars. Each work station is controlled by two hydraulic cylinders, which provide the possibility to work independently or in parallel on two stations simultaneously. The GEKA HYD 55/S ironworker machine weighs 1390 kg. Technical data of the GEKA HYDRACROP 55/S 2-cylinder ironworker machine General data - punching force: 55 t - cutting force: 110 t - number of workstations: 5 - number of hydraulic cylinders: 2 - engine power: 5 kW - weight of machine: 1390 kg Flat bar shearing station - flat bar dimensions: 300 x 15 mm; 200 x 20 mm - blade leng ...

Offer 24206 Specifications: - Max. working width 2030 mm - Max. material thickness at 40 kg/mm² strength 1.25 mm - Backgauge - Space requirement approx. W 2250 x H 1050 x D 750 mm - Weight approx. 700 kg

GEKA HYDRACROP 55/S hydraulic ironworker machine was built in 2018 in Spain by MAQUINARIA GEKA S.A. The machine, equipped with 5 work stations, is designed for precision machining of flat bars and angle bars. Each station is controlled by two hydraulic cylinders, which give the possibility to work independently or in parallel on two stations simultaneously. The GEKA HYD 55 S ironworker machine weighs 1390 kg. Technical specifications of the GEKA HYDRACROP 55/S ironworker machine General data - maximum punching force: 55 t - maximum cutting force: 110 t - number of workstations: 5 - number of hydraulic cylinders: 2 - engine power: 5 kW - weight of the GEKA HYDRACROP 55/S machine: 1390 kg Flat bar shearing station - flat bar dimensions: 300 x 15 mm; 200 x 20 mm - blade length: 305 mm - working height: 880 mm Angle bar shearing station - shearing of angle bar at 90°: 12 ...

Key data: 1000 mm, 1 mm

with rebate groove and wire insertion grooves Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Sheet width: 1000 mm Sheet thickness: 1.0 mm . Colour: blue Machine weight: 45 kg Space requirement: 1200 x 400 x 1000 mm Shaft diameter: 50 mm

55 ton multi station

pressure: 55 t punching cross-cut in cmm: mm stroke: 37 Min./20 mm throat: 500 mm stroke: max. 60 mm work height max.: 1060 mm total power requirement: 5 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 45 mm, 130 mm, 13 mm

Punching force: 70 ton Punching capacity: Ø 28 in 20 mm steel Projection: 300 mm Scissors: 130 x 130 x 13 mm angle steel 90º 450 x 15 mm flat steel 45 mm round steel Notching: 100 x 13 mm Equipped with: - Electric length stop 1000 mm - Various accessories - 2 stations machine Country of origin: Spain Motor power: 7.5 kW Machine LxWxH: 2000 x 1200 x 2000 mm Machine weight: 2000 kg

Combined profile steel shear and hole punch GEKA type HYD 80 / Hydracrop 80/AMasch. No. 9566 Year of construction approx. 2000Punching force 80 ton. Projection 300 mmPunching up to 40 mm in 14 mm sheet metalFlat material shears 450 x 15 mmAngle steel shears 130 x 130 x 13 mm4 edge shears 45 x 45 mmRound material shears 45 mmRectangular clinker up to 12 mmMotor power 5.5 kWNeching connection 400 volts, 50 Hz stop with el. Stroke release 500 mm - work table with stop at the hole device 550 x 380

Punching force: 110t, max. punching capacity: 40mm/20mm, throat depth: 750mm, stroke rate: 28/min, max. stroke: 80mm, working height: 1066mm, machine dimensions X/Y/Z: approx. 2300mm/1300mm/2300mm, weight: approx. 4000kg. An on-site inspection is possible.

L-profile: 120 x 120 x 10 mm flat steel: 300 x 15 mm round/square steel: 40 mm punching: dia 28 x 13 mm U/I-profile: 100 mm

Met elektrische achteraanslag Ponscapaciteit: 70 ton Dia x plaatdikte: Ø 28 x 20 mm Maximale slag: 80 mm 40 str / min Keeldiepte: 300 mm Werkhoogte: 1065 mm Maximale snijdikte in plaat: 20 mm Bladlengte: 455 mm 90°-snede: 130 x 130 x 13 mm 45°-snede: 90 x 90 x 10 mm Op maat gesneden rond/vierkant: 45 mm Elektromotor (vermogen): 7,5 kW Lengte: 1800 mm Diepte: 1200 mm Hoogte: 2000 mm Gewicht: 1650 kg

pressure: 70.0 t punching cross-cut in cmm: 27 in 20 mm punching cross-cut in cmm: 32 in 14 mm work height max.: 1060 mm column arm: 500 mm weight of the machine ca.: 1500 kg. total power requirement: 7.0 kW range L-W-H: 1550 x 1200 x 1950 mm ** good / well-maintained condition (!!) ** New price approx. 21.000 euros ** Special price on request Equipment: - electro-hydraulic hole punch, with large projection - large GEKA stop table with movable stop system - sheet metal stripper with stripper plates - stepless stroke adjustment - die base - 1x freely movable foot switch - operating instructions (PDF) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

GEKA HYDRACROP 55/S hydraulic ironworker machine was built in Spain in 2022 by MAQUINARIA GEKA S.L.U. This machine, distinguished by its extensive machining capabilities, is intended for precise hole and corner punching as well as shearing flat bars, angles and solid bars. Each of the 5 work stations is controlled by two hydraulic cylinders, which enable independent or parallel operation at two stations simultaneously. All this makes the offered GEKA HYDRACROP 55 S ironworker machine the perfect choice to significantly increase the productivity of any industrial plant. GEKA HYD 55 S weighs 1200 kg. Technical specifications of the GEKA HYDRACROP 55/S 2-cylinder ironworker machine General data - maximum punching force: 55 t - maximum cutting force: 110 t - number of workstations: 5 - number of hydraulic cylinders: 2 - total power: 5.5 kW - power supply: 400 V; 50 Hz - weight of  ...

GEKA HYDRACROP 110 SD hydraulic ironworker machine was built in 2020 in Spain by MAQUINARIA GEKA S.L.U. The machine is designed for the versatile machining of steel parts, enabling to perform multiple operations on a single machine, which increases production efficiency in industrial plants and locksmith workshops. The GEKA HYDRACROP 110 SD is equipped with 5 individual workstations, designed for punching holes and shearing flat bars, angle bars and steel bars. Each station uses interchangeable tools made of tool steel, which enables adaptation of the machine operation to the current production needs. The stations are controlled by two hydraulic cylinders and separate foot switch controlls, enabling the simultaneous operation of two operators at different stations and increasing production efficiency. All this is complemented by a robust design that maintains high stability during eve ...

GEKA HYDRACROP 110 SD hydraulic ironworker machine was built in 2009 in Spain by MAQUINARIA GEKA S.L.U. It is an extremely powerful and versatile machine designed for complex machining of steel parts, making it ideal for use in both production plants and locksmith workshops. The machine enables multiple machining operations to be performed in one place, such as punching holes and shearing flat bars, angle bars and steel bars. The GEKA HYDRACROP 110 SD is equipped with 5 independent workstations with interchangeable tools made of high-quality tool steel. Each station is hydraulically controlled by two cylinders and separate footswitches. This solution enables the simultaneous operation of two operators at different stations, which results in increased efficiency and production effectiveness. All this is complemented by a robust design, ensuring high stability even under intensive use.  ...

Key data: 2540 mm, 1 mm

Pull-out sheet metal support at the front, sheet metal slide placed at the front under the machine, hand back gauge, automatic hold-down device, dimensional grooves in the table Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Sheet width: 2540 mm Sheet thickness steel: 1.0 mm Sheet thickness aluminium: 1.5 mm Colour: blue Machine weight: 500 kg Dimensions: 2800 x 1500 x 1400 mm Cutting gap adjustment fixed Automatic hold-down Fixed cutting angle Back gauge: 650 mm Machine Number: 6.1-5005