used EXNER ex

EXNER EXSBR 200 hydraulic press YOM 8/1987 Serial No. 10042 Pressure 200 t Table 1800 x 800 mm Power requirement 65 kW Safety distance 195 mm Overtravel 52 mm Run-on time 120 ms Weight ca. 23 t

pressure: 200 t distance between columns: - mm stroke: - mm table surface area: 2000 x 800 mm total power requirement: kW weight of the machine ca.: 31 t dimensions of the machine ca.: m Drive power 55 / 4 kW Tracking travel 28 mm Safety distance 155 mm Tracking travel time 97 ms Oil filling 1200 liters The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

press ram:: ram head width: 2.100 mm depth: 840 mm stroke: 350 mm Control: EXNER Guide way length: 750 mm nominal pressure: 2x 400 kN return capacity: 2x 150 kN ram stroke speed - under load: 100%: ca. 0 - 10 mm/s ram stroke speed: ca. 0 - 20 mm/s T-slot - width: 18 mm T-slot - distance: 150 mm Installation Space:: dayligth: 550 mm table surface area: 1.600 x 840 mm T-slot - width: 18 mm T-slot - distance: 90 mm dist. between pillars (left to right): 1.700 mm dist. between pillars (front to rear): 600 mm table height over floor: 1.300 mm total power requirement: 11 kW weight of the machine ca.: 12 t dimensions of the machine ca.: 2,5 x 2,0 x 3,7 m Hydraulic tool testing press EXNER - PG 80 - very good condition - approx. 300 operating hours - Electronic roller feed device EV 22 AK incl. Bandwidth: max. 220 mm Band cross section: max. 200 mm² Feed length: 0.1 x 19,999 mm Speed: ...

a hydraulic four-column press Exner, type H4 SP 450, Y.O.M. 1983, pressure 450 to., side windows 475 mm. Installation height 600 mm, table area 1100 x 850 mm, impact area 300 mm, stroke 200 mm. Dimensions 3100mm x 2100 mm, depth 1,980 mm. Weight 13 to. ]

pressure: 200 t passage width: NA mm stroke: 180 mm table length: 690 mm table width: 530 mm distance between columns: 420 mm total power requirement: 18 kW weight of the machine ca.: t dimensions of the machine ca.: m Hydr. 4-Pillar Press for Embossing/Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 60 t throat: 330 mm stroke: 500 mm table surface area: 640x640 mm ram surface: Ø 120 mm table height: 850 mm tool hole in ram: Ø 50 mm weight of the machine ca.: 7 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 20 t throat: 185 mm stroke: 100 mm table surface area: 380 x 350 mm dayligth: 250 mm table height over floor: 840 mm total power requirement: 4 kW weight of the machine ca.: 1,3 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 125 t distance between columns: 1500 / 460 mm stroke: 400 mm total power requirement: 15 kW weight of the machine ca.: 10 t dayligth: 800 mm table surface area: 1900x870 mm ram surface: 1900x870 mm working feed: 0-10 mm/sec return speed: 0-20 mm/sec dimensions: BxTxH 2400x1500x3500 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure:150 t distance between columns:300 mm stroke:180 mm distance table/ram, max. stroke up, adjustment up:300 mm table surface area:570x180 / 300x410 mm table height over floor:875 mm side window:180 mm ram surface:180 mm speed down:250 mm/s speed up:160 mm/s working speed:6 - 12 mm/s oil volume:250 l power requirement:11,0 kW weight:2,4 t dimensions (WxDxH):1,3 x 1,3 x 2,4 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 § 20 foundation pit:nicht erforderlich

pressure:40 t distance between columns:495 mm stroke:150 mm distance table/ram, max. stroke up, adjustment up:300 mm table surface area:490 x 400 mm hole in the table:50 mm table height over floor:950 mm side window:155 mm ram surface:150 mm speed down:480 mm/s speed up:480 mm/s working speed:20 mm/s oil volume:115 l power requirement:7,5 kW weight:2,2 t dimensions (WxDxH):1,35 x 1,1 x 2,2 m depth stop:mechanisch foundation pit:nicht erforderlich

pressure:40 t distance between columns:500 mm stroke:150 mm distance table/ram, max. stroke up, adjustment up:300 mm table surface area:480 x 400 mm hole in the table:50 mm table height over floor:950 mm side window:150 mm ram surface:150 mm speed down:480 mm/s speed up:480 mm/s working speed:20 mm/s oil volume:160 l power requirement:7,5 kW weight:2,6 t dimensions (WxDxH):1,1 x 1,4 x 2,4 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 light guard:Sick depth stop:mechanical foundation pit:not necessary

Extruding system with cross-spray head for sheathing of small profiles/filaments consisting of: 30 mm extruder with tool, water bath, extractor and winder Optional with memory for role change

Nakata Zoki Kobe, Japan (Troester design) Duplex Extruder Unit Dual 150mm dia PIN Type Extruders, Year of manufacture: 1990, with Roller Feed, and duplex Die. L/D ratio 16:1 Number of Pins: 10 Rows x 8 Pieces, Spare Pins included. Screw Speed 45 r.p.m. Motors 185kw D.C. variable speed, 415 volt, 3ph, 50hz. Full Books and Drawings available. Thyristor Drives included. Starter and Control Panel for Lower Extruder only. Die usable Width 18\\, In good condition.

Francis Shaw 90mm coldfeed rubber extruder.Year: 1992. Machine No.4846Vented. Side power roller feed,L/D ratio 20:1,H series David Brown gearbox,Thrige Scott 63kW, 2000rpm DC variable speed motor.Machine fully overhauled, cleaned/painted and fitted with NEW electrical control panel. With provision for 5 x TCU's.

Drum pump, hygienic ExzenterschneckenpumpeVon of the company GrünpumpenTechnische DatenTyp ds.: LDS 80.1Ser. No.: 0259 Qm³ / h 2,40N1 / min: möglichVerpackung 6,75ZahlungsmodalitätenBarzahlung pick up and transfer in advance and shipping pick up, shipping via forwarding and abroad by prior arrangement all data were listed to the best of our knowledge and belief.Errors are reserved. This auction is aimed only at professionals, dealers, and other legal persons.

Single-screw extruder with new 7,5kW drive, new gear box, new cylinder and new screw 30 mm - 28 d, nitrated new ceramic heating elements, cooling fan, temperature sensors Control cabinet integrated in the machine frame Machine frame on wheels Stainless steel hopper

Plant for the production of filament for use in 3D printers Capacity up to 10 kg/h consisting of 30 mm extruder, stainless steel trough, puller and winder with traverse guide

Thank you for your interest in our gum extruder system we offer you as follows: many thanks for your interest on our new chewing gum extruder plant, please follow our offer find: AUTOMATIC EXTRUDING; ROLLING AND SCORING MACHINE 7 ´ ´ /. COMPLETE LINE for production of chewing gum sticks and Chiclets Manufacturer: WLS Type: Chewing gum Extrudier-, rolling and cutting machine gum extruder, rolling and cutting system Product: Chewing gum sticks and Chiclets Size (working width): 7 ´ ´ / 177mm other dimensions are possible on demand Type: WLS RAS 7 "with manual take-off Capacity: Approx stick gum. 200-250 kg / h / Chiclets approx. 250-350 kg / h Number of rolling stations: 4 Number of cutting stations: 2 Electrical: 400V 3 ph 7 "ROLLING AND SCORING MACHINE incl. EXTRUDER Conveyor belt is covered with powderin ...

8" Cold Feed Rubber Extruder

Te Koop: Rubber expansion joints. Merk: Toraflex. Type: PMS 16 bar TMS 110 degrees! 00% EPMD. Bellows: DN 100 PN 16. Flens doorsnee, 220mm 8 gating HoH: 180mm Doorsnee gat: 18mm

Dominioni Punto & Pasta Pasta extruder machine Stainless 8Kg hopper with agitator and stainless screw, variable speed, variety of extrusion plates for different style pastas, mobile

Cast Film CoEx System (ABA), PE / PP, Capacity: approx. 400 - 700 kg/h, Main extruder, 120 mm, co-extruder of 60 mm, screen changer, melt pump, Co-Ex block, nozzle 1,650 mm, 2-roll chill-roll smoothing unit, cooling section, extractor, double winder with cutting device and edge control, edge trim, film measuring device thickness NDC (without measuring head), incl. operating instructions and e-plans.

available Troester Triplex Extruder Top machine QSM 90x 16D Middle machine 200W x 6D Below machine QSM 150 x 16D Head MW500 Description attached!

vertical design, for simultaneous extruding of 4 strands, Sausage masses, etc. each strand with a diameter of approx. 15 mm, Capacity approx. 15 l, Drive 1.5 kW

Description TWIN HELIX EXTRUDER Screw Diameter 90 mm L/D 30 Screw Speed 161 rpm Barrel Zones 5 Motor Power 91Kw Motor Speed 1750 rpm Automatic Screen Changer Produced Material PP & PE