135,480 used machines on RESALE, but how to find them? Machine Search
Bread slicer Band slicer PS Mako Slicer 400 - Ribbon bread slicer - Manufacturer: PS Mako - Type: Slicer 400 - Operating voltage: 400 volts - Rated current: 8A - Year of construction: 2002
Essemtec 1x CLM9000 but without a functioning laser beam Feeder ready for delivery: 2x CLM950 2x CLM952 1x CLM955 1x CLM9561x CLM950LED) Operating hours: 15282 Cassette slots: 6x 1x tray table Find more here - .ucymachines/ Contact us at - sales@ucymachines
Essemtec FLX2010 MKL Used assembly machine from Essemtec type: FLX2010 MKL with a vacuum table for assembly of printed electronic components. With vacuum pump and feeders. Voltage: 230V Current: 3A Find more here - .ucymachines/ Contact us at - sales@ucymachines
2007 Mercedes Combined heat and power plant (CHP) The CHP plant was originally intended for an oil platform. Therefore, it is protected against salt water and can also be operated in island mode. Technical data (See pictures) CHP plant with Mercedes engine, which is designed for multi-quality fuel (diesel, heating oil, pyrolysis oil or vegetable oil). Thus preheating unit and corresponding exhaust gas purification. BJ. 2007. Operating hours: 0 (test run only); The unit was never connected to the network. If palm or vegetable oil is used, preheating” is required to get above the pour point. All pumps were completely overhauled by the manufacturer when we purchased them (see Rg with maintenance report). If you want to drive in island mode, this must be changed on the control + the controller on the generator must be replaced. In addition to electricity, the unit can also recover ...
Cable and hose protection spiral in set PAGUS length: 820 mm inner diameter: 30 mm outer diameter: 42 mm wire diameter: 6 mm set consists of 6 spirals ! used, tested ! Dimensions(packaging): 880 x 130 x 140 mm
Key data: 206 KW, 500 kVA, 400 V
Sokratherm Gas-CHP GG202 oE Gas electricity and heat generators from 2019 with 10,777 operating hours, Complete CHP (closed unit) with additional silencer. 1 available 202 KWel x 1,500 rpm, 400 V/50 Hz. AC Generator: Leroy Somer LSA 47.2M7 V 6/4, 500 KVA Manufacturer: Sokratherm Model: GG202 oE Type: Gas CHP Serial Number: 3131754 Engine: MAN E3262E302 Electric power [KWel]: 206 Thermal power [KWth]: 316 Gas Capacity [KWgas]: 561 Year of Make: 2019 Hours: 10,777 Weight unit [kg]: 6,500 Dimensions LxWxH [cm]: 400 x 150 x 240 AC Generator LSA 47.2M7 V 6/4 Manufacturer: Leroy Somer Model No.: LSA 47.2M7 V 6/4 Type: AC Synchronous Generator Serial Number: 353345/1 Power [KVA]: 500 Voltage [V]: 400 Frequency [Hz]: 50 Current [A]: 722 Speed [1/min]: 1,500 Year of manufacture: 2018
Banding maretial PW8030150 white paper 40 rolls and PB7030150 brown paper 40 rolls. Banding maretial PW8030150 paper white 40 rolls and PB7030150 paper bouwn 40 rolls.
Bread slicer Treif Diskus 400+ circular knife -digital control - Cutting width adjustable from 3 mm to 15 mm - 400V 50Hz - Stainless steel cladding - Weight 195 kg - Operating voltage 400 volts - Control voltage 24V/DC V AC - Nominal power 0.9 kW - Year of construction 2015 External dimensions: width 80 cm depth 70 cm height 112 cm
Rego Herlitzius Type: Rotec 350 Circular knife Year of construction 2010 Cutting width: 3 – 25mm completely made of stainless steel for loaves max 3250mm length on casters tested and cleaned Stock level: 2 pieces
The warehouse for paints and solvents ( in barrels ) is housed inside the building and consists of 3 Departments. The warehouse complies with the applicable regulations, - Pallets of solvents can be stored on the right side. There are taxiways here - In the middle, paint buckets are stored on a shelf - On the left side, paint containers are stored on a shelf. In the containers are stirrers ( included in the delivery )
SMD pick and place machines Advantage - Series Mimot system is expected to be available at the end of 2024 This system is part of an entire assembly line that can be purchased in its entirety 1) Infeed conveyor assembly 1 Easytrans - LP conveyor belt 1x600mm, width adjustment via CAN with Absolute encoder 2) assembler MIMOT Advantage active X 1 SMD assembly machine consisting of: 1 basic unit 1 feeder capacity for 184 S8 tracks (Applicable feeder types: TriligentFeeder™ and coded belt feeders / coded band feeders ) 2 head module, for holding a maximum of 5 (111140) assembly heads 6 assembly head for optical centering, with self-learning Z-axis (Touch-Sense technology) Arrangement: 2 head modules, each with 3 assembly heads 12 standard vacuum pipette 1112xx of your choice 1 autom. Changing station for 10 vacuum pipettes (occupies space for 6 S8 tracks) 1 PCB holde ...
used fat baking appliance Treif Pegasus, overhauled, 50 Hz, 400 V, 0.9 kW, control system has been renewed, completely in stainless steel version, weight: 168 kg
2008 Mimot Advantage machine 2008 is expected to be available at the end of 2024 This system is part of an entire assembly line that can be purchased in its entirety 1) Infeed conveyor assembly 1 Easytrans - LP conveyor belt 1x600mm, width adjustment via CAN with Absolute encoder 2) assembler MIMOT Advantage active X 1 SMD assembly machine consisting of: 1 basic unit 1 feeder capacity for 184 S8 tracks (Applicable feeder types: TriligentFeeder™ and coded belt feeders / coded band feeders ) 2 head module, for holding a maximum of 5 (111140) assembly heads 6 assembly head for optical centering, with self-learning Z-axis (Touch-Sense technology) Arrangement: 2 head modules, each with 3 assembly heads 12 standard vacuum pipette 1112xx of your choice 1 autom. Changing station for 10 vacuum pipettes (occupies space for 6 S8 tracks) 1 PCB holder for automatic loading (in- ...
liter capacity: . l feed pressure: . bar coolant capacity: . l The technical data is manufacturer or operator information and is therefore not binding for us. We reserve the right to sell the goods prior to sale, our terms and conditions of business and sale apply exclusively. About us more than 400 of our own machines in stock over 12,000 m² of storage space, crane capacity 70 t more than 1,000 items of accessories for your workshop If you want to sell machines, production lines or your business, then contact us. You can find further offers on our website. Viewings are possible by arrangement. We look forward to your visit. Your Markus Hirsch team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 40 t stroke: 250 mm total power requirement: 6 kW weight of the machine ca.: 3 t distance between columns: 600/350mm mm table surface area: 860x620 mm ram surface: 860x620 mm table height: 900 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Digital Turning diameter 120 mm Turning length 700 mm Spindle speed 2000 min-1 Tailstock
pressure: 300 t distance between columns: 1350/1000mm mm stroke: 500 mm weight of the machine ca.: 20 t table surface area: 1900x1600 mm ram surface: 1900x1600 mm table height: 1000 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 400 , 800 , 1000
Center distance 6000 mm Height of centers 400 mm Max diameter on the bench 800 mm Max diameter on the carriage 520 mm Max diameter in the recess 1100 mm Bar passage 130 mm Undercarriage stroke notes 340 mm TURRET Standard BENCH Max weight between tips 3500 Kg Max weight on steady rests 4500 Kg Pallet width 520 mm TAILSTOCK Steerer diameter 115 mm Steerer stroke 380 mm Cone cm6 HEAD Spindle power 25 Kw Spindle speed 5/1000 Rpm 11" cam-lock spindle attachment Spindle torque 560 Nm GiVi axis display measurements Self-centering 500 Use and maintenance books Yes Wiring Diagrams Yes Protections yes Ready for availability Visible in the warehouse in operation
Swing over the bed: 1250mm Max length of the workpiece: 10000mm Max mass of the workpiece at machining between centres with rest: 10000kg Height of the cutting tool set in tool holder: 50mm
Pallet roller conveyor Accumulating 7500-1000-840 RA2349 Conveyor length (FL): 7500 mm Roller width (RB): 840 mm Outer width/nominal width (NB): 1000 mm Roller spacing / pitch 175 mm Frame height: 160 mm Current storage space size approx. 900 mm 8 storage spaces Storage mechanism can be converted for other storage space sizes, e.g. 1200 mm for Euro pallets Length can be extended/reduced. Several units available single roller drive chain, so that several elements can be driven with one motor. for pallet weights up to 1000 kg Optionally available supports side guides Frequency inverter for infinitely variable speed control Price plus VAT ex central warehouse Dr. Sonntag GmbH & Co. KG 97076 Würzburg Features: Electric data: 1,1 kW, 380-500 V condition: good (used) Conveying length in mm: 7500 Nominal / outside width in mm: 1000 Roll width in mm: 840 Roll division in mm: 175 Driven: YES sc ...
Height 1950 mm Width 1800 mm Length 1500 mm Weight 1400 kg Power supply: 400V 50Hz 3N Total power 18 kW Loading Loading integrated into the machine Description Vacuum filler Handtmann VF 622 in a set with a grinder GD 93-3
Key data: 140 mm, 280 mm
Zimas D290V - Lathe Special price € 2,800 instead of € 3,490 excl. VAT - 2-axis position indicator - Stepless speed adjustment with digital display - Plan feed - Camlock mount C4 - Upper slide can be rotated 360° - Tailstock adjustment +/- 5 mm for taper turning Accessories - Undermount with 1x door & 3x drawer - Three-jaw chuck 160 mm with interchangeable jaws - Fixed bezel - Centering tip - Operating tools Specifications Range: - Circumferential Ø over bed: 290 mm - Circulating Ø over cross slide: 180 mm - Turning length between tips: 700 mm - Bed width: 182 mm Headstock: - Spindle bore: 38 mm - Spindle nose: MK5 - Speed levels: infinitely variable - Speed range: 80 - 2000 rpm Feed: - Metric threads: 0.2 - 3.5 mm / 18 steps - Inch thread: 8 - 56 dpi / 21 levels - Longitudinal feed: 0.085 - 0.832 mm - Transverse feed: 0.01 - 0.10 mm Sleds a ...
Height 1200 mm Width 1250 mm Length 1750 mm Weight 600 kg Capacity 3500 kg/h Power supply: 400V 50Hz 3N Total power 52 kW Cutter Type Through Cutter Cutter design Stainless steel, acid-resistant Knife shaft speed 2970 rpm
Ultrasonic Banderolier ATS US 2000 AST-MDM; cleaned and tested; Frame size 900x750mm; Belt width 30mm; suitable for paper (also suitable for TruePaper paper) or foil; Meter reading 795,000 thousand; Compressed air required. Ultrasonic banding machine ATS US 2000 AST-MDM; cleaned and checked; frame size 900x750mm; band width 30mm; used for paper (also for TruePaper material) or foil; counter 795,000; pressurized air needed.
Straight and cut machine Wafios R31 Diameter: 1-5mm – 7mm MY: 1993 – working condition Machine Number: 26106224 Extension length: 2m or 6m available Pay-Off: not available, we can offer separate for 3t. Mechanically refurbished Electrical checked Machine is in working condition
turning diameter over bed: 410 mm turning diameter over slide rest: 240 mm turning length: 1000 mm centre height: 205 mm centre distance: 1000 mm spindle bore: 47 mm spindle turning speed range: 28 - 1250 U/min feeds - longitudinal: 0,03 - 8,8 mm/U feeds - cross: 0,006 - 1,84 mm/U thread - mm pitch: 0,25 - 76 mm thread - inch: 1/2 - 152 Gg/ thread - module: 0,25 - 22 mm bed width: 320 mm tailstock quill diameter: 55 mm tailstock taper MT: 4 face slide travel: 290 mm upper slide travel: 120 mm total power requirement: 5,5 kW weight of the machine ca.: 1,3 t dimensions of machine L x W x H: 2,32 x 1,15 x 1,22 m Accessories: 3-jaw chuck RÖHM 160 mmø, MULTIFIX-head with 2 inserts, solid steady, running center, coolant The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Standing steel tank with inner coating Suitable for; Extinguishing water or rainwater Volume: 70,000 L Dimensions: Ø 3.00 × 11 m high Call us or write to us! We would be happy to make you a non-binding offer! Scholten Tanks GmbH Brüsseler Str. 1 48455 Bad Bentheim/Gildehaus Phone: 05924 255 485
: 0360 mm : 215 mm : 1000 mm : 180 mm : 45 mm : 3,75 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
horizontal steel tank with inner coating, pressure tank Can be used underground and above ground Volume: 35,000 L Dimensions: Ø 2.50 × 7 m long Call us or write to us! We would be happy to make you a non-binding offer! Scholten Tanks GmbH Brüsseler Str. 1 48455 Bad Bentheim/Gildehaus Phone: 05924 255 485
: 0350 mm : 196 mm : 0650 mm : 170 mm : 42 mm : 7,5 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Steel tank with inner coating (epoxy resin) Can be used above or below ground Volume: 32 m³ Dimensions: Ø 2.50 m × 7.00 m long On request and as required, the tank can be equipped with a brand-new dome, fire brigade connections, suction line, inlet and overflow. In addition, the tank is treated with a new external coating (anti-corrosion). Anti vortex plate, water level gauge, etc. can be offered. Call us or write to us! We would be happy to make you a non-binding offer! Scholten Tanks GmbH Brüsseler Str. 1 48455 Bad Bentheim/Gildehaus Phone: 05924 255 485
Used biscuit line for continuous round and square rolls BERTUETTI, Type: Universal Line - for round rolls, such as hamburgers and square ones - Universal dough divider and rounder SV250-G14 - Continuous rounding by G14 - Feed belt 1,900 mm - 6 rows - 1, 2, 3 or 6 rows can be used - Guillotine cutting system - Automatic sheet loader N20 for sheet sizes 60 x 100 cm - Lifting tipper - Dough intake - Sowing SST - Good condition, ready for immediate use Visits and test runs are possible by arrangement.
Used biscuit line for round, square and hot dog buns BERTUETTI, type: 200 Universal - for round, square and long-rolled rolls, such as HotDogs - 4 rows - 1, 2 or 4 rows can be used - with settling on sheet metal - Dough intake - Sowing - Good condition, ready for immediate use Visits and test runs are possible by arrangement.
x-travel: 500 mm y-travel: 400 mm z-travel: 400 mm Control: Heidenhain TNC 310 tool taper: SK 40 speeds: 20-4500 U/min weight of the machine ca.: 3 t dimensions of the machine ca.: 2,15 x 2,00 x 2,50 m Equipment/accessories: -swivel rotary table -documentation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 0360 mm : 215 mm : 1000 mm : 180 mm : 45 mm : 2,25/3,25 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
FULL WEIGHING AND BAGGING LINE - EXCELLENT CONDITION FULLY WORKING COMPLETE WITH STAINLESS STEEL GANTRY, INCLINE FEED CONVEYOR AND OUTFEED CONVEYOR GEA SMART PACKER GX250H - VERTICAL FORM FILL SEAL BAGGER 250MM JAW MACHINE NO: 12330 YEAR: 2017 WEIGHT: 950KG 415V MULTIPLE TUBE SETS ISHIDA MULTIHEAD WEIGHER MODEL: CCW-RVE-216B-10/15-SS MACHINE NO: 560012161 16HEAD YEAR: 2017 240V WEIGHT: 535KG PLEASE DO NOT HESITATE TO CONTACT FOR MORE INFORMATION
Center height: 300 mm Center width: 1000 mm Circumferential Ø: over bed 610 mm Spindle bore: 71 mm Spindle mount: size 8 Pick-up cone tailstock: 5 MK Spindle speeds: approx. 11.2 - 1800 rpm Feeds: longitudinal/flat 0.014-16/0.063-7 mm/rev Thread pitches: 0.1 - 112 mm Electrical connection: 380 V, approx. 5.5 kW Space requirement: 2900 x 1450 x 1750 mm
Center height: 400 mm Center width: 1250/1300 mm Circumferential Ø: over bed 440 mm Spindle bore: Spindle holder: Pick-up cone tailstock: 5 MK Spindle speeds: 11.2 - 2240 rpm Feeds: longitudinal/flat 0.1-2.8/0.05-1.4 mm/rev Thread pitches: Electrical connection: 380 V, 11 kW Space requirement: 3400 x 1400 x 1300/1700 mm Weight: approx. 2700 kg
: 0330 mm : 210 mm : 0635 mm : 167 mm : 40 mm : 2,2 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
FZWD 160x1600/1 Sabo Basis 160 Facing & Centering Machine WMW HECKERT Workpiece dia 20-160 mm Length 130-1600 mm Max. Diameter of Milling Cutter 200 mm Facing Spindle's Speeds 112-280 rpm Spindle's Speeds 560-1400 rpm Adjustable feed rate range 15 – 800 mm / min. Spindle ISO 50 Rapid traverse 6000 mm Max. stroke 230 mm Max. Depth of 6 mm Tool holder 4 - 20 mm Max. Feed path 60 mm Total connected load 20 kW Weight 4.5 t
YOC 2001, working width 220 cm, 4 weft colors Stäubli electron. dobby 2871 – 16 shafts installed, Sumo motor, electron. take-up and warp let-off, max warp beam flange dia. 1,000 mm, off-loom take-up
: 0390 mm : 240 mm : 1000 mm : 190 mm : 54 mm : 5,5 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
02 sets Picanol Air-Jet Weaving Looms, type OmniPlus Summum – 250-4R YOC 2015, working width 250 cm, 4 weft colors Stäubli electron. dobby 3220 / C4Can – 16 shafts installed, Sumo motor, electron. take-up and warp let-off, double whip rollers, max warp beam flange dia. 1,000 mm, off-loom take-up
turning diameter over bed: 360 mm turning diameter over slide rest: 220 mm turning length: 1000 mm turning diameter in the gap: 380 mm turning speeds: 70 - 2000 U/min centre height: 180 mm spindle bore: 50 mm tailstock quill taper MT: 3 MK connected load frequency: 230 oder 400 V total power requirement: 1,8 kW weight of the machine ca.: 0.65 t dimensions of the machine ca.: 2,0 x 0,8 x 1,56 m Professional industrial machine 3-axis digital display 3-jaw chuck 180 mm. 4-jaw chuck 200 mm. Faceplate 280mm Bezel fixed Bezel rotating 4-fold steel holder. Halogen machine light Machine light Foot brake removable chip tray, chip protection wall Hardened and ground bed rails Complete coolant system Feed protection Machine tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Frey OSCAR 20 Piston Filler used Machine is equipped with two rollers that allow manoeuvring with the toggle lever folded out It comes from an insolvent company, the piston with gasket, union nut, piston wrench and piston screw could not be found during the dissolution and were therefore reordered, see pictures. The machine is completely made of stainless steel (body, cylinder, piston and cover) and is in the same condition as it was returned by the customer, so it must be thoroughly cleaned before use Video about test run available
used bread slicer Wabäma R400 E, overhauled, with circular blade, for below counters
Industrial Processing Tank – 19,517 L Working Capacity (2006) High-capacity industrial processing and storage tank designed for hygienic handling of liquid food products in beverage and dairy processing environments. The tank offers robust construction, high temperature tolerance, and pressure capability suitable for modern production lines. General Information - Year of Manufacture: 2006 - Condition: Used, operated only for a short period Capacity - Working Capacity: 19,517 liters Technical Specifications - Maximum Pressure: 4.0 bar - Maximum Temperature: 145 °C Dimensions - Outside Diameter: 2,570 mm - Total Height: 6,830 mm Key Advantages - Large 19,517 liter working capacity - Suitable for high-temperature processing applications - Designed for pressure-resistant operation up to 4.0 bar - Ideal for dairy, beverage, and liquid food processing - Robust ...
Magnetic swivel table as shown in the pictures. Further information on request
Bore diameter: variabel mm Number of heads horizontal: 1 St. Number of heads vertical: 0 St. 1 Götzinger dowel gluing and insertion machine BLE With the BLE, the workpieces are glued and dowelled on the front. Optional the BLE can be upgraded with a drilling unit, counter milling unit and longitudinal stop will. A 10 touch panel allows easy operation for manual or online operation. Base frame: in a compact design, covered with sheet metal Table support approx. 800 x 200 mm position 1 ---------------------- 1 glue station full jet valve Glue quantity precisely adjustable Glue gun for counter hole gluing position 2 ---------------------- 1 stainless steel glue pump, high-pressure pump and glue hose item 3 ---------------------- 1 press-in station with dowel separation and press-in cylinder item 4 ---------------------- 1 oscillating conveyor for dowels d 8 x 50 mm with feed hose into the ...
Offer 24177 Specifications: - Tip height 180 mm - Center width 1000 mm - larger circulation – Ø over bed 355 mm - via flat sleds approx. 200 mm - Spindle bore 36 mm - Pick-up cone of the tailstock quill MK 5 - Travel of the tailstock quill 260 mm - Spindle speeds 18 - 1800 rpm -Feeds - Travel of the cross slide approx. 200 mm - Travel of the upper slide approx. 115 mm - Drive 400 V / 5.8 kW - with: - Tailstock, 3-jaw lining, bezel - Steel holder, moving center punch, - Chip tray - Space requirement approx. W 2500 x H 1500 x D 1200 mm - Weight approx. 2100 kg
maximum number of results exceeded
please refine your search
