weinig moulder used for sale

WEINIG planer/moulder Unimat 22A with 9 heads Year of construction: 1987 Serial number 222-896. The planer is in good working condition and has been partially overhauled, cleaned and subjected to careful technical controls. • The machine has been thoroughly cleaned and technically checked. • Some wear parts have been replaced. • A test run was carried out to ensure functionality. • The machine is bolted to a wooden structure and is ready for shipment. • The planer and moulder is equipped with all the tools and is sold as such. Further technical data of the machine: Maximum planing width: 220 mm Maximum planing height: 140 mm Diameter of the spindles: 40 mm Spindle speed: 6000 rpm Length of the inlet table: 2 m The machine has a total of 9 spindles with the following configuration: 1. Lower spindle / dressing spindle : 5.5 kW 2. Right spindle /  ...

WEINIG moulder model UNIMAT 17N with 8 shafts: -useful working measures 170x120mm -gimbal towing and pneumatic pressure -variable feed speed -top feed wheel before the 1st shaft -tandem feed groups in front of the 2nd and 4th shaft -2000mm long entrance plane -with SACOT automatic loader -manual lubrication pump of the table Tree layout: 1-under 2-right 3-left 4-right 5-above 6-under 7-above 8-Universal

Moulder Weinig PFA 14/7 Specifications: Working width (mm) 140 Waves: 7 1. Shaft: bottom 2nd shaft: right 3rd shaft: left 4th shaft: right 5. Shaft: up 6. Shaft: down 7th Wave: Uni Wave

SECOND-HAND 5 SPINDLES MOULDER WEINIG PROFIMAT 23 E - CE RULES working width 260 mm working height 160 mm. composition : - horizontal bottom 5.5Kw - vertical right (7.5Kw Rh + Lh) - vertical left - horizontal top 7.5Kw - horizontal bottom 11Kw year 1998 (CE) V 380/50

SECOND-HAND 5+1 SPINDLES MOULDER WEINIG MOD. PROFIMAT 23E - working width mm.230 - infeed working table 2000 mm. - 1st spindle horizontal bottom 4kw - 2nd spindle vertical right 7,5kw - 3rd spindle vertical left - 4th spindle horizontal top 7,5kw - 5th spindle horizontal bottom 4kw - 6th spindle universal 4kw - volt 380/50 - s/n 228-80241 - year 1995 (CE)

WEINIG planer and moulder model Unimat 22 A Equipment: - Package - Lifting table (no pit required) - automatic stacking strip removal - Rubberized inclined conveyor - Rubberized separation - Longitudinal conveyor for planing.- Moulder - Unimat 22 A with soundproof cabin - 2nd operating unit - Manual acceptance Weinig Planer.- Automatic throat machine, technical data: Spindle arrangement: U - R - L - O - U Saw Working width: 220 mm Working height: 120 mm Motor power feed: 4 kW Motor power of the working spindles: 4 kW Speed of the working spindles: 6000 rpm. Diameter of the working spindles 40 mm Feed infinitely variable 6 - 32 m/min Diameter of feed rollers (hardened) 140 mm Space requirement line: 12.7 x 5.0 m Spelling mistakes and errors excepted

TECHNICAL DATA: Working width mm: 230 Planing height mm: 120 Infeed table length mm: 3500 Number of spindles: 6 Spindle configuration: 1 B: 5,5 KW 2 R: 7,5 KW 3 L: 7,5 KW 4 T: 7,5 KW 5 B: 5,5 KW 6 T: 5,5 KW Spindle diameter mm: 40 Feedrate m/min: 6-36 Rotation speed max rpm: 6.000 Soundproofing cabin: Yes Feeding magazine Weinig - PHV - 2004

2-sided planing machine with slot bed: Year of construction 1993 Working width 170 mm Working height 120 mm Working height 4-sided 120 mm Number of spindles 4 Spindle arrangement u-o-u-o Diameter of the spindles 50 mm Spindle speed 6000 rpm Engine power 30-22-11-11 kW Feed speed 12-120 m/min Driven rollers in table 6 Automatic table lubrication Table height constant 840 Diameter of the suction nozzles 4x160 mm Weight 4500 kg Space requirement 4000x1700x1400 mm Voltage / Frequency 400V 50Hz 3Ph.

Capacity: 230 x 120 mm. Spindles: 4 bottom 4 kw fence and near 5,5kW top 5,5 kw Spindle diameter 40 mm Cardan shaft drive, motor 2,2 kW Pneumatic pressures Infeed table 2 m lengte Waxilitpump for bed lubrication, manual Safety hood 4 cutterblocks

SPECIFICATIONS: Passage mm: 230 Length entrance table mm: 2000 machining height mm: 120 Spindles: 6 Spindle configuration: 1 BOTTOM - CW 5.5 2 RIGHT - CW 5.5 3 LINKS - CW 5.5 4 TOP - CW 5.5 5 BOTTOM - CW 5.5 6 UNIVERSAL SPINDLE - WEEK 7.5 Spindle diameter mm: 40 Cardan shaft drive Feed speed: 6-36 m/min Revolutions per minute: 6,000 Soundproof cabin

Capacity: 230 x 130 mm. Spindles: 8 Bottom 7.5 kW, fence 7.5 kW, near 7.5 kW, 2nd fence 7.5 kW, 2nd near 7.5 kW, top 11 kW, bottom 7.5 kW universal 11 kW Grooved bed Cardan shaft drive Pneumatic pressures Intermediate driven feedroller for short pieces Automatic bed lubrication Spindle diameter: 40 mm. Spindle speed 8000 r/min 5 driven feedrollers in table Feed: 6 - 36 m/min, motor 5,5 kW Automatic hopperfeed Tooling not included

SPECIFICATIONS: Pre-spindle machine inlet: 2000 mm Working width: 210 mm Working height: max. 120 mm Cardan shaft drive Drive shaft power: 2.2 kW I. Spindle: Bottom (4 kW) II. Spindle: Right (3 kW) III. Spindle: Left (4 kW) IV. Spindle: Right (5.5 kW) V. Spindle: Above (5.5 kW) VI. Spindle: Above (5.5 kW) VII. Spindle: Bottom (4 kW) With tools

SPECIFICATIONS: Planer: 2500 mm Machinable width: max. 210 mm Working height: max. 150 mm Cardan shaft drive Drive shaft power: 5.5 kW Spindle configuration: I. Spindle: Bottom (4 kW) II. Spindle: Right (4 kW) III. Spindle: Left (5.5 kW) IV. Spindle: Right (4 kW) V. Spindle: Top (4 kW) VI. Spindle: Bottom (4 kW) VII. Spindle: Universal spindle (5.5 kW) With tools.

SPECIFICATIONS Pre-planer mm: 2000 Number of spindles: 5 Spindle configuration: I below - week 5,5 II - III right- left - KW 7,5 IV above - week 5,5 V below - week 4,0 Cardan shaft Speed-controlled drive KW: 4.0 Spindle diameter mm: 40 Revolutions per minute: 6,000 Max. working width mm: 230 Max. machining height mm: 120 Complete with: - Soundproof cabin - Grooved table -Tools CE-compliant

Capacity: 230 x 130 mm. Spindles: 7 Bottom 7,5 kW, right 7,5 kW, left 11 kW, right 7,5 kW, top 11 kW, bottom 11 kW, universal 11kW spindles 2, 3, 4 and 5 are 8000 tr/min straight jointer on 2nd bottom spindle Cardan shaft drive Pneumatic pressures Intermediate driven feedroller for short pieces 0,8 m infeed straightening table manual bed lubrication Spindle diameter: 50 mm. 5 driven rollers in table Feed: 6 - 36 m/min, motor 7,5 kW motor height adjustment

SPECIFICATIONS: Entrance headstock of mm: 2500 Number of spindles: 5 Spindle Configuration: I Down - CW 5,5 II - III right-left - week 7.5 IV Top - CW 5.5 V Down - CW 4.0 Cardan shaft drive Gear motor KW: 2.2

WEINIG Hydromat H23 LINE, S/N 89533 Package chain conveyor with 5 chains approx. 2,700 x 4,800 mm WEINIG infeed transverse transport HighMech E-1, with 7 flat chains approx. 2000 x 4200 mm WEINIG Hydraulic Roller Accelerator 814 Short infeed table with heavy 4-roller feeder WEINIG Outlet HighMech A-5 Pull-out hinge approx. 2,000 mm x 250 mm Transverse transport with 7-fold cam chain 4,200 mm Transfer to 7-fold flat belt transport Scissor lift with driven chain support Automatic planer with reinforced KASCHWIG soundproof booth 3-sided • Working width max. 230 mm • Working height max. 160 mm • Electronic feed infinitely variable 8 – 80 m/min. • Feed motor 18.5 KW • 1st spindle bottom 15.0 KW • 2nd spindle right 11.0 KW • 3rd spindle left 11.0 KW • 4th spindle top 15.0 KW • 5th spindle bottom 11.0 KW • 6th spindle t ...

SPECIFICATIONS: Pre-planer machine inlet mm: 2000 Number of spindles: 6 (5 + 1 universal) Spindle Configuration: I Bottom: CW 5.5 II - III right-left: week 7.5 IV top: week 5.5 V Bottom: KW 5.5 VI Universal spindle: KW 5.5 Cardan shaft drive Variable speed drive KW: 3.0 Revolutions per minute: 6,000 Max. working width mm: 230 Max. working height mm: 150 Spindle diameter: mm 40 Central lubrication inclusive: - Soundproof booth -Tools CE Marking

WEINIG high performance planer Type Hydromat 22 BL (full checked!) Built in 1995 With safety hood and soundproofing cabin! Machine specifications: - Planing capacity 220 x 120 mm - Feeding, 8- 80 m/min, motor 18.5 kW Spindle layout: Bottom-right-Links Top - bottom, table rigid Bottom, table rigid, spindle prepared Top - bottom, table rigid, spindle prepared gap unit, consisting of 1 right and 1 left spindle 30 kW each (4500 rpm) incl. table roll, sliding roller, spray indentation and wedge dissipation 4 Roller pull-out Special printing and fittings for the production of top layer slats Feed (divider) for slats and pull-out tape

Cutting and planing machine MAKA / Weinig • Lift table • Multi-rip saw MAKA type V350: o Year of construction: 1996 o Chain width (mm): 350 o Cutting height max. (mm): 120 o Engine power (kW): 22 o Feed rate (m/min.): 0 – 40 • Material transfer to the moulder • Moulder Weinig PFA 14/7: o Working width (mm): 140 o Shafts: 7 o 1st shaft: bottom o 2nd shaft: right o 3rd wave: left o 4th shaft: right o 5th shaft: top o 6th shaft: bottom o 7th wave: Uniwelle

WEINIG moulder model UNIMAT 17A with 8 shafts: -useful working measures 170x120mm -gimbal towing and pneumatic pressure -variable feed speed from 6.3 to 36.5 mt/min -Double wheel of upper feed before the 1st shaft -tandem feed groups in front of the 2nd and 4th shaft -fluted plane from 1st to 6th shaft -2000mm long entrance plane -manual lubrication pump of the table Tree layout: 1-under 2-right 3-left 4-right 5-above 6-under 7-above (free space below)    8-Universal

SECOND-HAND 3 SPINDLES MOULDER WEINIG MOD. UNIMAT SUPER 4 - Working width 25-150 MM. - Working thickness 15-50 MM. - Feeding speedy 5/20 M/MIN. - 1st spindle 11 Kw - 2nd spindle 18.5 Kw - 3rd spindle 5.5 Kw

High-speed planer and moulder Weinig H30 R for four-sided planing and profiling of wet wood (freshly sawn) The machine is in the queue and is being prepared for delivery after the order has been placed., working width: 250 mm, working height: 140 mm, spindles: 5, spindle 1: Bottom (7.5 kW) - counter bearing, spindle 2: Right (11kW), spindle 3: Left (11kW), spindle 4: Above (15 kW) – counter bearing, spindle 5: Below (30 kW) - toothed belt drive / counter bearing, feed: 15 kW, control: ATS system, Powered table rollers: Yes

Key data: 5 , 260 mm, 180 mm

Moulder WEINIG model PROFIMAT 23 (260×180) FORTEC, in configuration for carpentry / lamellar processing: – useful working measures 260x180mm – electronic control of 2 axes, SIEMENS programmer SIMATIC OP7 – gimbal towing and differentiated pneumatic pressure – variable feed speed 5 – 24 mt/min – feed motor KW 4 – HP 5,5 – upper feed group before the 1st shaft – lower feed group after the 5th shaft – machine top with air film – short 1050mm entry plane – foot lubrication pump – protection cabin – shafts D=40mm at 6000rpm – complete with tools D = 120mm - Z = 2 Trees: 1- under kw 11 – hp 15 2- Right 3- Left (right and left with single engine kW 11 – HP 15) 4- above kw 11 – hp 15 5- under kw 7,5 – hp 10 Machine according to CE standards

All-round automatic planer and moulder Weinig Powermat 500 for four-sided planing, profiling and ripping Folding device and CNC control in excellent original condition. Spindle 1: Bottom / 7.5 kW / HSK Powerlock / 8,000 rpm Spindle 2: Right / 7.5 kW / HSK Powerlock / 8,000 rpm Spindle 3: Left / 7.5 kW / HSK Powerlock / 8,000 rpm Spindle 4: Top / 7.5 kW / HSK Powerlock / 8,000 rpm Spindle 5: Bottom / 15 kW / HSK Powerlock / 4,000 - 12,000 rpm Includes a set of HSK Powerlock tools/adapters, spindles: 5, working width: 230 mm, working height: 120 mm, Dressing table length: 2.000 mm, CNC Control: for spindle 2,3,4,5, Driven role: in the exit table, Control: PowerCom Plus, feed: 3kW / 5 – 30 m/min

Techn. Equipment Ablaengsaege slit spindle 6 tools Fraesspindel 3 tools groove drill Fraesspindel 3 tools Beschlagsnutfraese

DECKLAGEN PRODUCTION LINE TORWEGGE with WEINIG H22BL FINSIH LAYER PRODUCTION LINE ML-Presseen Torwegge Heating bed length 3 m Wood types FI, AI, LÄ, DG, ZI ML slat width 60 - 140 mm ML- Slat thickness 8 - 15 mm Rod width 25-45 Rod thickness 17-31 mm Possible. Carpet widths 1273 - 2073 mm Special widths 1000, 1700 mm Target capacity/layer 300 m2 LH 500 m2 19 - 31 mm Fi Functional principle continuous Plate length mm 10000 Plate width mm 6600 Workpiece thickness max mm 45 Pressing force t 10 Further technical data Workpiece thickness min mm 25 Input length min mm 450 Fugue glue press Yes The technical data are partly estimated. Actual values can be may differ. = English = Technical data are partially estimated. Actual values may ... WEINIG High Performance Profile Machine, Type Hydromat 22 BL Built in 1995 with splitting unit (lamella saw) Bring (au ...

CATALOG NO. 6946 TECHNICAL SPECIFICATIONS - max width of the workpiece 210mm - max thickness of the workpiece 120mm - number of spindles 2 pcs - spindle diameter 50mm in advance: - 3 insertion, pulling, rubber, smooth shafts including 2 double - 2 leading, rubber, pulling shafts including 1 double - heads on supports - head adjustment up / down - electric height adjustment of the upper head - electrical setting of planing thickness - spindles equipped with a brake - main motor 2×5,5kW - smooth regulation of feed speed - feed motor 3kW - feed on cardan shafts - diameter of extraction connection 2x160mm - dimensions length / width / height 2350x1780x1950mm - weight 1882kg – German production – jointers – for sharpening knives on the head – 2 Hydro heads included – unpainted – very good condition, used planer Net price: 33900 PLN Net price: 7533 ...

FOUR SIDED PLANER model WEINIG PROFIMAT P 23 E with 5 spindles second hand machine working condition : Excellent CE mark : Yes volt. 380/50 grooved table ( removable ) quick tool locking device with tools : Yes , as in video Composed by 5 spindles , 4 motors : 1° spindle : planer . motor power Hp 5,5 ( Kw 4 ) 2° and 3° spindles : right and left vertical . motor power Hp 7,5 ( Kw 5,5 ) 4° spindle : thickness planer . motor power Hp 10 ( Kw 7,5 ) 5° spindle : planer . motor power Hp 5,5 ( Kw 4 ) grooved table ( removable ) quick tool locking device Technical details : forward motor power Hp 4 ( Kw 3 ) shaft rotation speed rpm 6000 feed speed : from 5 to 24 mt./min. max. useful working width mm. 230 max. useful working height mm. 120 shaft diameter mm.40 inlet length mm. 2000 automatic lubrication system electric height adjustment set of service keys / d ...

MULTI MOULDER machine type WEINIG PFA 17N second hand machine 6 spindles with tools - Composition : 1° shaft : surface planer . motor power Hp 5,5 2° shaft : spindle moulder . motor power Hp 4 3° shaft : spindle moulder . motor power Hp 5,5 4° shaft : spindle moulder . motor power Hp 5,5 5° shaft : thickness planer . motor power Hp 5,5 6° shaft : surface planer. motor power Hp 5,5 inlet length mm. 2000 feed speed: from 7,8 to 58,8 mt./min max. useful working width mm. 170 max. useful working height mm. 120 lubrication system weight kgs. 2600 volt. 380/50

Raimann ProfiRip KR 310 M My. 2004 Multi-blade rip saw with 2 adjustable saw blades Track width 340 mm Total - passage width max 950 instead of 800 mm Cutting height with / without pressure board 115/130 mm Workpiece length 450 mm min Saw blade max. diameter 380 mm Saw blade min. diameter 250 mm Saw blade bore 80 mm Saw spindle diameter 65 mm Saw spindle speed 3900 rev / min Engine 30 kW Laser - directional lights 3 pc. Operating push 6 bar Infinitely variable feed - speed 8-48 m / min. 1.5 kW Weight 3400 kgs Voltage 400V/50Hz

Working width mm 260 Planing height mm 160 Table length mm 2500 Number of spindles 4 Continuously variable feed

Automatic multi-platform saw with leaf adjustment and part back conveyor Neumann Type: MRF 16/4.000: Technical data: Follow later!

Automatic optimization crosscut saw: Technical data: Follow later!

Clamping cylinder suitable for wedge tine press

Planing machine Weinig hydromat H30 W baujar 1990 36m/min Working width 300mm working-high 200mm memeeser of the fresspindel 50mm with suction

WEINIG HYDROMAT 22 BL Year of construction 1995 with splitting unit (lamellar saw) Feeding (Automatic feeder and pull-out unit!) With safety hood and soundproof cabin! Machine specifications:  - Planning capacity 220 x 120 mm  - Feeding, 8– 80 m/min, motor 18.5 kW Spindle layout:  Bottom-right-left Top - bottom, table rigid Bottom, table rigid, spindle prepared Top - bottom, table rigid, spindle prepared Gap unit, consisting of 1 right and 1 left spindle each 30 kW (4500 rpm) incl. table roll, sliding roller, spray barrier and gap wedge removal 4 roller pull-out Special pressure and fixtures for the production of top layer slats Feeder (all-in) for slats and pull-out tape     

Specifications Spindles: 2 Spindle arrangement: Bottom (5.5 kW) – Top (5.5 kW) Working width: 220 mm Working height: 120 mm Feed: 3 kW // 32 m/min Spindle diameter: 50 mm Jointer Counter bearings Short Parts Package

Specifications Spindles: 2 Spindle arrangement: Bottom (5.5 kW) – Top (5.5 kW) Working width: 220 mm Working height: 120 mm Feed: 3 kW // 32 m/min Spindle diameter: 50 mm Jointer Counter bearings Short Parts Package

Winkelanlage Weinig including tools Type: UC 10/6 Year of construction: 1994 Cross wood processing 7 x stroke (7 tools on top of each other at IV 68) Longitudinal machining 3 shafts: 2 pieces with 3 x stroke and 1 piece with 2 x stroke Screen control for individual programs such as individual and series production Swivel stop arm for inclined window processing Tool: IV 68 Leitz (Dufix) with extension kit for sash 78 mm / frame IV 68# IV 68 with rung profile (carnish arch on the glass fold) IV 78 Zuani (for weather legs and rain rail) with extension kit for IV 90 (Zuani) with extension set for wood-aluminium windows (Aluminum shell as glass holder outside of Zuani) Weight 4700 kg

I sell the Fensterbau Profil Umfälzautomat Zentrum Weinig Univar 10. Year of construction 1998. Milling heads OERTLI. Available the same. Unit price 5.500 euro. 4 pcs. available. Condition very good !

I sell the Fensterbau cone cutting and slotting system Weinig Unitec 10. Year of construction 1998. Milling heads OERTLI. Available the same. Unit price 5.500 euro. 3 pcs. available. Condition very good !

I sell the window construction kit: 1 pcs. cone cutting and slotting system Weinig Unitec 10. 1 pcs. profile automatic converter center Weinig Univar 10. Year of construction 1998. Milling heads OERTLI. Available the same. Price together 10,000 euros. Condition very good !