We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
122,054 used machines on RESALE, but how to find them? Machine Search
used
The SF 4120 gantry center is in good technical condition with a sliding table and a fixed gantry stand. Heidenhain iTNC 530 control system. The SF machine meets high demands in surface machining of molds, edge cutting, 3D machining of molds and in precise finishing of contours. Can be seen in operation by appointment The price of the machine also includes accessories, e.g.: 2-axis head - High-pressure cooling through the center of the spindle 20bar/ - Z axis – balancing system - Chain tool magazine for 40 tools (exchange in vertical position) - Two screw chip conveyors - MPG handwheel - Blow the spindle with air - Flushing gun and interface to the pneumatic circuit - Work probe HEIDENHAIN TS-640
used
description: The detection is adjusted for 0,5l glass bottles and twenty modul crates.The inspector comes with a multi camera system. If an external bottle is detected, the crate will be pushed out in an other line. Currently the set up is for a long side leeding crate. Informations without guarantee Besides buying and selling of conveyors and machines our strength lies particularly in services and project planning, as for example in rebuilding and adapting of your installation as well as in overhaul and relocation of machines. You have a first idea or even a concrete plan? It does not matter how far your project is, we support you in every phase! Or do you want to sell or market your machine? We also buy machines or provide you with a marketing concept. Ask for your individual offer or visit us in Knetzgau. Concerning bigger projects we can of course also visit you ...
used
VISION WIDE VB-2016 5-AXIS CNC gantry milling machine was manufactured in 2013 in Taiwan. The machine performs precision machining of heavy workpieces in three or even five axes, once the automatic swivel head is mounted to the vertical spindle. The machine’s top-quality cast-iron structure is rigid and resistant to bending stress, thus perfectly dampening the vibrations and oscillations generated during machining. The VISION WIDE VTEC VB 2016 CNC gantry milling machine centre is equipped with safety guards fitted around the entire machine with sliding doors that open flush with the X-axis travel. Inside, there is a large work table with a length of 2000 mm and a width of 1300 mm, which is supported along the entire length of the longitudinal travel and guided by two sliding guideways, making it possible to machine heavy workpieces even when the table is unevenly loaded. Two scre ...
used
Electronics module -Isra Vision Systems AG: PCspork v1 1 -Dimensions: 127/153/H22 mm -Weight: 0.13 kg
used
Vision Wide SF-3116 Bridge Type Machining Center X : 3100 mm Y : 1600 mm Z : 800 mm Machine is in very good condition
used
Key data: 3100 mm, 2000 mm, 800 mm
Vertical Machining Center Make: Vision Wide VTEC Type: SF 3120 CNC Year of construction: 2014 Technical details: x-axis: 3100 mm y-axes: 2000 mm z-axes: 800 mm Table size: 3000 x 1800 mm Speed 10,000 rpm. Operating hours 17,500 h
used
Description: VISION Lynx Digital Stereo Microscope Approx. Onsite Dimension. (l x w x h): 700 x 400 x 850 mm, weight approx.: 50 kg
used
Capacity: 1,500 K/h Types of boxes: Boxes of 6, 0.7 VdF, 200 x 300 x 320 mm, transverse Boxes of 6, 1.0 VdF, 200 x 300 x 320 mm, transverse Boxes of 12, 0.7 VdF, 355 x 270 x 310 mm, longitudinal running Boxes of 24, 0.2 goiter neck KK, 300 x 400 x 210 mm, longitudinal run Boxes of 24, 0.2 goiter neck SV, 300 x 400 x 210 mm, longitudinal run The following evaluations are integrated: crate geometry, foreign bodies, crate color, bottle height, bottle color + Box pusher VT-1201 Year of construction: 2016 Capacity: 1,500 K/h Box types: Boxes of 6, 0.7 VdF, 200 x 300 x 320 mm, cross run 6-boxes, 1.0 VdF, 200 x 300 x 320 mm, cross run Boxes of 12, 0.7 VdF, 355 x 270 x 310 mm, lengthwise run 24-boxes, 0.2 Kropfhals KK, 300 x 400 x 210 mm, longitudinal barrel 24-boxes, 0.2 goitre neck SV, 300 x 400 x 210 mm, longitudinal run The following evaluations are integrated: crate geo ...
used
Technical data Table length: 300 mm Table width: 250 mm Magnification: from: 8 x up to: 40 x
used
The detection is set up on 0.5l glass bottles in the 20 module box. The inspector is equipped with a multi-camera system. As soon as a foreign bottle is detected in the box, it is then discharged via a pusher. Currently is set to cross travel. The detection is adjusted for 0,5l glass bottles and twenty modul crates. The inspector comes with a multi camera system. If an external bottle is detected, the crate will be pushed out in an other line. Currently the set up is for a long side leeding crate.
used
Overview The Crate inspector was built in 2017 by Germany manufacturer Visiontec. It is adjusted for 0,5l glass bottles and twenty modul crates. The inspector comes with a multi camera system. If an external bottle is detected, the crate will be pushed out in another line. Currently the setup is for a long side leeding crate.
used
This Vison Wide VTEC SF-2112 Vertical Machining center was made in 2014 and has 17000 production hours. It is equipped with a Fanuc Series Oi-MD control unit and has 3 axis. The machine has a spindle speed of 10000 rpm.
used
This Vison Wide VTEC SF-3120 Universal Machining center was manufactured in the year 2014 and has 17500 production hours. It is equipped with a Fanuc Series Oi-MD control unit and has 3 axis. The machine has a spindle speed of 12000 rpm.
used
Scanner WoodEye 6 SortCut Model: W6-SC-4444RR with inlet and outlet mechanization, manufacturer Invenir The scanner was only in production for 12 months. Equipment WoodEye 6: 4-Sided Grayscale Analysis 4-sided color analysis 4-sided profile measurement 4-sided roughness analysis 4-Sided Fiber/Texture Analysis/Angle Measurement for hard and softwood Optimization for 4 finishing products The WoodEye scanner is equipped with a UPS for the computers to provide a controlled shutdown in the event of a power outage Invenir mechanic: Infeed and outfeed conveyors with double belts on both sides and pneumatic pressure. All four belts are driven together by a motor with adjustable speed Subject to changes, errors and prior sale
used
CP Food machinery A/S slicer, model: VISION SLICER, type: IPS 3000, serial number: 9329, year of construction: 2007, 400 V, 3 Ph, 50/60 Hz, 16 A, plastic belts, belt width: 200 mm, total dimensions: 3600 mm x 1100 mm x 1800 mm. Incomplete.
used
Marel Salmon A/S Multi Angle Vision slicer, model: GEBA SC 125 MA V, type: 10-68°, serial number: 8937, year of construction: 2012, 400/220 V, 3 Ph, 50 Hz, 8 A, weight: 775 kg, plastic belt, belt width: 260 mm, total dimensions: 2700 mm x 1000 mm x 1500 mm.
used
3D Vision Camera SICK RANGER-D50213 1040384 Power consumption: 7 W supply voltage: 24 V DC ± 20 % lens: LINOS MeVis-C 1:1.6 focal length: 25 mm used, tested ! Dimensions: 175 x 56 x 84 mm
used
RayTec Vision optical sorting machine, type: RAYNBOW, model: R-230-M3-R, serial number: 1622, year of construction: 2020, 400 V, 50 Hz, 3 kW, plastic belt, belt width: 745 mm, total dimensions: 2500 mm x 1350 mm x 2600 mm.
used
Description: serial number: 64116010 travels: X-axis: 200 mm Y-axis: 250 mm Z-axis: 100 mm resolution/ lenght standard: 0,1 ,µm / linear encoder image detecting unit: colour CCD camera drive speed: max 80 mm/s stage glas size: 269 x 311 mm max. stage loading: 10 kg  , including computer, monitor and software Approx. Onsite Dimension. (l x w x h): 465 x 815 x 663 mm, weight approx.: 80 kg
used
CO2 laser cutting and engraving machine brand Birio model Vision Cut 10. Year of construction 2019 Perfect state of use, certified and guaranteed as new directly by the manufacturer. Working hours: 2880 Working area 1000x800 mm Cutting material thicknesses up to 20mm. workable material: wood, plexiglass, acrylic in general, fabric, paper, cardboard, anodized aluminum, cork, leather, leather and various others. The operator panel allows you to work even without a connected PC. The machine is equipped with a dry compressor, generator cooling unit, adjustable optics. The machine is equipped with CE conformity certification, use and maintenance manual. Vision Cut complies with the requirements of the national Industry 4.0 plan Included is the Birio Suite. Available for viewing and testing.
used
This Mitutoyo Quick Vision Apex Measuring machine was manufactured in the year 2014 in Japan.
used
CNC machining center for wood/plastic and composite materialMake REICHENBACHER type Vision - 1, year of construction 1999Technical specifications:Travel X:3740 mmTravel Y:1680 mmTravel Z:340 mmC axis = rotation: +/- 360°Feeds axis speed: 60 m/min.Feed web speed: 85 m/min.Z axis: 20 m/min.C axis:90°/sMilling unit speeds: 1500 - 18000 rpm.Tool holder: SK 40Distance table and spindle min./max.: 80 / 420 mmEnd mill diameter: 24 mmProfile milling cutter diameter: 100 mmTool changer slots:12Tool length max.: 200 mmTool diameter max.: 200 mmTool mass per piece / total: 6 - 50 kgTable size: 3800 x 1500 mmDrive power: 25 kWWeight approx.: 6.5 tWith- Drilling unit spindle speed 4500 rpm., 2.2 kW- Vacuum / grid table- CNC control Siemens 810 D with central unit CCU2 and software module MMC 103- Compressed air requirement 300 - 500 L/min.- Filter systemused, in good conditionPrice on request.Deli ...
C - elbow, type Ziehm Vision R in very good technical and optical condition.
used
Manufacturer: Reichenbacher, Type: Vision 2 Sprint, Year: 1999, Control: Simumerik 840 D, Working range X: 6140, Working range Y-axis: 1600, Working range Z: 480, Feeding speed max m/min: 60, Pendulum processing: yes, Number of milling spindles: 4, Milling engine 1 hours power: 4,8, 2 station allocation: yes, 4 station allocation: yes, Vacuum pumps m³/h: 160, Year :1999
Mobile X-ray C-arm Ziehm Vision
C - arch in very good technical and optical condition. Little used.
used
grinding diameter: 350 mm grinding length: 1500 mm centre height: 175 mm total power requirement: kW weight of the machine ca.: 3 t dimensions of the machine ca.: m Overhauled and modernized machine -DRO in x and z-axis -New BEMA tailstock with 0,1mm cylinder compensation -Park position for the tailstock -New automatic switch off when diameter is reached -Automatic switching from rough to finish grinding -Finish grinding feed electrical infinitely variable from 0-100% -Modernized infeed handwheel like on the new machines -swiveling operator panel -Splash doors -coverd x-axis with possibility to set an exhauster on top -New internal grinding device like on the new model -new hydraulic aggregate -New electric cabinet -Scontrol voltage 24V instead of 220V Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrS ...
used
• DataMatrix station for labelling and verification of folding boxes, cartons and rectangular bottles (serialisation and aggregation). • Output max. 400 items/min, belt speed 5 - 90 m/min • Data matrix code square 10 x 10 - 144 x 144 modules, rectangular max. 16 x 48 modules • Various other readable code types, including Pharmacode • Product run from left to right • Product transfer by alignment belt, consisting of lower (600 mm long) and height-adjustable upper belt (400 mm long) • Ejection belt 300 mm long • Product height max. 150 mm, product width 45 - 130 mm • Bad product ejection by pneumatic pusher with collecting container • Ejection countercheck • Central height adjustment for printer and camera • Light barrier for product detection (trigger) • 1 LAN PCE camera Mini-Smart, plain text/code control 6.217 • 3 installation positions for camer ...
used
Suitable for regrinding and making new wood and metal working tools of all kinds. Accessories: Lift - loader (automatic loading and unloading device), Software Tool Studio Standard & Advanced Version 1.9, Software package 1 (cylindrical tools with sharp edges, corner and full radius),, Software package 2 (conical spiral tools with sharp edges, corner and full radius),, Software package 3 (drills and step drills),, Software package 16 (warm-up program), Software package Heli-Flute + Cone (flute calculation program), automatic fire extinguishing system, Glass scales on all linear axes X, Y, Z, Electrostatic mist extractor,, Chiller for spindle cooling,, Probe,, Pneumatic workpiece clamping,, Oil collecting pan,, 2 grinding wheel flanges., Longitudinal movement (X-axis): 480 mm, Y axis vertical movement: 320 mm, Z-axis transverse movement: 700 mm, Rotary table swivel range C-axis: +/- 200 ...
used
HEXAGON OPTIV CLASSIC 321 GL tp optic measuring machine was built in 2009 in Switzerland. This technologically advanced machine is the best solution for highly accurate measurement and inspection of e.g. electronic parts, micro-hole dies, fibre optics and inkjet nozzles. Thanks to the use of an 8-segment LED ring light with RGB colour sensitivity adjustment, the HEXAGON vision measuring machine detects and captures the edges of coloured parts much more easily compared to standard greyscale or lighting modifications. The offered machine also features, among other things, a 3 axes microprocessor CNC with vector path control, a CCD camera with 6.5x zoom and PC-DMIS Vision metrology software with the innovative MultiCapture function, which finds all 2D characteristics in the field of view simultaneously, increasing the inspection speed by up to 50%. The total weight of the machine is 170 kg. ...
used
Epson C3-A601S 6-Axis Robot Assembly Station Assembly of parts for car radios and navigation systems and for testing them. The assembly station is surrounded by a protective enclosure. The service doors are equipped with interlocking monitoring switches. The doors are locked in automatic mode and can only be opened when the automazik stop or in manual mode after pressing the doors on the control panel. When the door is open, automatic operation cannot be started, the robots and servo drives of the Statioin are stopped, the pneumatic actuators are switched off and cannot be operated. This station consists of 3 functional substations: Functional sequence St.6.1: Control of ribbon cables: Lift the drive out of the chassis and tilt the drive code Control of 3 ribbon connectors by means of vision sensors on the robot gripper arm Reseat the drive in chassis St.6. ...
used
Tank Environmental Protection Wozniack . Specialist establishment according to Section 19 of the Water Budget Act (WHG) offers as follows . Diesel tank 10,000 litres double-walled used, with a new diesel pump Vision 60 The container is used, cleaned, overhauled and is equipped with the following fittings: 1 optical leak detector with type approval and leakage liquid (new) 1 filling pipe with TW closure (filling cap) and immerse tube, 1 bearing tube with bearing rod and bearing rod closure, 1 vent pipe with vent hood, 1 brand new limit sensor with type approval (AIII) (new) 1 ladder 1 Diesel pump Vision 60 (new) . Flow rate approx. 50 LTR/min . Hose length 4mtr can be extended. Container dimensions Length 5,310 mm Diameter 1,600 mm Weight approx. 1,500 kg Of course, you can also use your tank system. We are happy to offer you diesel pumps with a hig ...
used
Tank Environmental Protection Wozniack . Specialist establishment according to Section 19 of the Water Budget Act (WHG) offers as follows . Diesel tank 7,000 litres double-walled used, with a new diesel pump Vision 60 The container is used, cleaned, overhauled and is equipped with the following fittings: 1 optical leak detector with type approval and leakage liquid (new) 1 filling pipe with TW closure (filling cap) and immerse tube, 1 bearing tube with bearing rod and bearing rod closure, 1 vent pipe with vent hood, 1 brand new limit sensor with type approval (AIII) (new) 1 ladder 1 Diesel pump Vision 60 (new) . Flow rate approx. 50 LTR/min . Hose length 4mtr can be extended. Container dimensions Length 3,710 mm Diameter 1600 mm Weight approx. 1,500 kg Of course, you can also use your tank system. All our tank systems are used in our company by selected employ ...
used
Tank Environmental Protection Wozniack . Specialist establishment according to Section 19 of the Water Budget Act (WHG) offers as follows . Diesel tank 25,000 liters double-walled used, with a new diesel pump Vision 80 The container is used, cleaned, overhauled and is equipped with the following fittings: 1 optical leak detector with type approval and leakage liquid (new) 1 filling pipe with TW closure (filling cap) and immerse tube, 1 bearing tube with bearing rod and bearing rod closure, 1 vent pipe with vent hood, 1 brand new limit sensor with type approval (AIII) (new) 1 ladder 1 Diesel pump Vision 80 (new) . Flow rate approx. 70 LTR/min . Hose length 4mtr can be extended. Automatic pumpgun new . Container dimensions Length 8,390 mm Diameter 2,000 mm Weight approx. 4,500 kg Of course, you can also use your tank system. We are happy to offer yo ...
used
Tank Environmental Protection Wozniack . Specialist establishment according to Section 19 of the Water Budget Act (WHG) offers as follows . Diesel tank 7,000 litres double-walled used, with a new diesel pump Vision 80 The container is used, cleaned, overhauled and is equipped with the following fittings: 1 optical leak detector with type approval and leakage liquid (new) 1 filling pipe with TW closure (filling cap) and immerse tube, 1 bearing tube with bearing rod and bearing rod closure, 1 vent pipe with vent hood, 1 brand new limit sensor with type approval (AIII) (new) 1 ladder 1 Diesel pump Vision 80 (new) . Flow rate approx. 70 LTR/min . Hose length 4mtr can be extended. Automatic Zapfpisole is new . Container dimensions Length 3,710 mm Diameter 1,600 mm Weight approx. 1,450 kg Of course, you can also use your tank system. We are happy to offe ...
used
BLISTER MACHINE FOR AMPOULES FARCON FC320 WITH VISION SYSTEM SEA VISION For thermoforming trays for ampoules, vials. Manufacturer: Farcon (MARCHESINI GROUP) Model: FC320 Year: 2002 Automomatic ampoules feeder on trays Pick and place system to pick up trays and place them on a conveyor Two-way conveyor Maximum forming depth: 42 mm Speed: 45 cycles/min Maximum forming area: Film width 254 mm; Film pitch 220 mm Maximum cutting area: Film width 248 mm; Film pitch 210 mm Maximum production: 63000 ampoules (1 ml)/h Hydraulic network: - Pressure : 1.5 to 2 bars - Connection : Ø 1/2" Gas - Temperature : 11°C to 15°C - Average consumption : 200 l/h Pneumatic network: - Pressure: 6 to 8 bar - Connection: Ø 3/4" - Consumption: 500 Nl/min Power supply: 400V 3-phase, 50Hz, 3A Power: 6kVA CARTONER CAM MODEL HV2 FOR AMPOULES Model: HV2 ...
used
The unit is suitable to pack blisters in PVC + Aluminum, Aluminum + Aluminum, Polypropylene, PET and PVC, Aclar, COC. All the stations are remarkably easy to access and all the movements are fully visible, so that the line is very easy to clean. This machine is equipped with various safety devices to protect the operator. Product parameters can be recalled from a PC, for a quick and easy format change. Reel unwinder driven by a Brushless motor, with automatic machine stop at reel end. Film splicing table equipped with integrated cutter, and automatic vacuum. Forming station entirely managed by Brushless motors. Self-aligning pre-heating plates, independently motorized. Film positioning driven by Brushless motor. Automatic Pitch adjustment directly from the display. Loader trolley MS170 with a maximum load of 300 kg. Dedicated product feeder and relevant enclosure easily remov ...
used
BLISTER LINE ROMACO NOACK (BLISTERING MACHINE + CARTONING MACHINE) Year of construction: 1998 Blister packing line consisting the following two machines, both electrically upgraded in 2020 with new PLC and HMI. Noack 920 blister packer: Maximum draw depth: 12 mm Maximum foil width: 160 mm Maximum capacity: 80 forming strokes per minute Blister collation system for feeding into the cartoner Automatic tablet track in-feed system Tablet feeders into brush box Suitable for packaging tablets or capsules into Alu/Alu or PVC/Alu blisters Variable speed Laetus vision system Vacuum system HAPA H-226-C printer Romaco Promatic P150 fully automatic horizontal intermittent cartoning machine: High production speed, format change without tools Carton dimensions: minimum: 20mm x 15mm x 60mm; maximum: 100mm x 85mm x 150mm Minimum carton dimensions: 20mm x 15mm x 60mm Ma ...
used
Burner types: PT - 600 and PT - 15 XLS plasma power source: ESP 200; 100-160 volts; 40-200 A cutting method underwater Plasma cutting cutting table L:6,7xB:1,63xH0,79m Trafo ESAB ESP200 L:1,05xB:0,55xH:1.1m/330kg Portal; Rails x-way 7500 mm y-path 2700 mm Welding speed 2-750 IPM m/min Control CNC Vision 1000 cutting width y=max. 2438 mm thickness unleg. Steel=50.8 mm thickness of alloyed steel=38 mm thickness Alu=32mmmm burner cod1 piece Adjustment burner=approx. 150mmmm Total power requirement 39.8 kVA machine weight approx. 4.0; ready for immediate use
used
CNC Portal Cutting Machine Manufacturer: ESAB Type: SXE P1 3500 LH Year construction: 2001 CNC control: Vision 51 Working area: 2x6 m Track: 8 m 2 x car use burner under power to visiton request dismantling and commissioning on request; available from 37 KW 2016
used
Serialization system for packaging line: suitable for the printing of code data on the cartons. Incl. camera vision system, bad ejection and data management system etc.
used
Corima AEC212 Syringe Labeler and Plunger Inserter with Plunger Unscrambler and Label Easy-Splice It is an automatic, continuous motion machine for syringe plungering and labelling. Main features: • Perfect operational repeatability; • Easy to use; • Minimal installation space; • Designed to manage each component with positive logic; • Totally customizable, with wide choice of optional units (e.g. Vision system, printing systems, feeding systems, etc); • High flexibility and capacity to process glass or plastic syringes. Standard constructional specifications: • Automatic syringe loading on roller conveyor; • Automatic loading of the plungers with elevator and roller conveyor or with vibrating feeder; • No syringe – No plunger loaded; • Totally parameterizable screwing unit; • Plunger assembly control; • External labelling unit complete with unwi ...
used
CNC Portal Plasma Cutting Machine Manufacturer: ESAB Eagle 2500 Year of construction: 2004 Control: Vision DNC Connection track width: 2,500 mm runway: 5 m Working area: 2 x 3 m Extraction table 1 plasma torch with power source Kjellberg HiFocus 160i automatic gas console (see PDF) cutting tools: up to 25 mm filter cutting system: Columbus Immediately available ; ready for immediate use
used
WSM Stationary screwdriving unit screwdriving station Assembly of parts for car radios and navigation systems and for testing them. The assembly station is surrounded by a protective enclosure. The service doors are equipped with interlocking monitoring switches. The doors are locked in automatic mode and can only be opened when the automazik stop or in manual mode after pressing the doors on the control panel. When the door is open, automatic operation cannot be started. Functional sequence The station is equipped with the pre-assembled assembly via the transfer belt. The work steps of the automatic station with a run of a WT are described below. In normal operation, all 3 stations work in parallel. - Positioning the WT with the pre-assembled assembly in St.2.1 - Lowering the wearer with the scanner and the vision sensor - Scanning of the 3 codes (front panel, fro ...
used
Esab Combirex DX 3000 Working range: 2500mm x 4000mm 1x Plasma Support CNC Portal Plasma Cutting Machine Manufacturer: ESAB Type: Combirex DX 3000 Built: 2015 Control: Vision T5 Track width: 3,000 mm frame: 6000mm Working range: 2500mm x 4000 m suction table 1 plasma torch with power source m3 202 torch PT 36 Cutting rods: Punching: 38 mm Cutting: 45 mm laser pointer filter system ex protected cutting software: Columbus Very low operating hours commissioning on request
used
CANON OCÉ ARIZONA 460XT large format printer built in Canada in 2013, is designed to provide the user with near photographic quality of prints with excellent text clarity. To make this possible, the CANON inkjet printer uses a piezoelectric method, during which special crystals change their shape and volume under tension and pressure on a membrane, and then splash under high pressure onto the printed surface. The use of this technology results in excellent image sharpness, density and uniformity, both while printing on a roll media and on a flat substrate. The OCÉ ARIZONA 460XT UV flatbed printer has an extra large work table with a vacuum system, with which oversized media with a maximum size (L x W) of 3060 x 2510 mm are held stationary to ensure accurate registration of multiple prints. Printing of large-format media uses a piezo head configured for CMYK + WHITE colour support, w ...
used
CNC Portal plasma cutting machine Manufacturer: ESAB Eagle 2500 Year of construction: 2004 Governance: Vision DNC connection Track width: 2,500 mm Career length: 5 m Work area: 2 x 3 m Vacuum table 1 plasma torch Kjellberg HiFocus 160i power source automatic gas Console (see PDF) Cutting thickness: up to 25 mm quality section Filter system Cutting software: Columbus Now available
used
IMA CARTONING MACHINE, MODEL K150C Year of manufacture: 1995 (overhaul: 2011) K150 is an accessible, reliable and efficient cartoner ensuring quiet running at high speed. Its carton prebreaking and opening system combined to extrapositive carton handling by multiple belts ensures best carton forming control. Its design allows fast access and easy cleaning. The machine is equipped with a feeding system for bottles, a feeding system for vials, a GUK Cartonac 81 FA21/ 4 leaflet feeder, IncJet printing and control unit, Antares Vision print control system. TECHNICAL DATA Frequency: 50 Hz Voltage: 380 volts Power: Kw 4,5 Weight: Kg 1500 Production characteristics: Min carton dimensions: mm 20 x 12 x 50 Max carton dimensions: mm 85 x 60 x 190 Max production: 150 cartons/min Pressure: 6 ATM The K150 can handle a wide range of product feeding groups (bottles, squeezable ...
used
we sell 1 of 2 used tray / carton setup with an additional magazine for a package leaflet or e.g. Spoon that is placed in the box and glued to the bottom. The tray / carton erector has 2 Nordson hot glue devices (Pro Blue) each and is completely built in V2 A (also the control cabinet). The system is adjustable in terms of cardboard height and width as well as length, but are set to a currently fixed level. The systems are in a very good used condition as they were in stock after a factory closure (optical condition is almost as new). The special feature of the system is that a vision system (by KEYENCE) is installed in the system, which can check a correct insertion of the package leaflet or the spoon and can stop the system if it is not executed correctly (looks at the tray from above). The system is immediately available and could also be converted to other tray types (stacking corner ...
used
30 cm image amplifier with 2 x magnifying glass function 100 Hz double monitor, Black Vision, 250 Image Memory Usb DFP, DAP Resolution 1.2 - 1.4 Lp/mm X-ray emitter scan replaced in 2019 Refurbished