TRACTO-TECHNIK GMBHGrundodrill 12 GS Drilling rig Grundodrill 12 GS Drilling rig Grundodrill 12 GS vehicle + locating system drill Track G2
Truck to 7731 T31 with 2 axle trailer with ramps
-ONE year of manufacture 1995
Drilling rig GRUNDODRILL 12 GS
-Manufacturer TRACTO-TECH ...
used machine
Drilling rig Grundodrill 12 GS vehicle + locating system drill Track G2;
;
Truck to 7731 T31 with 2 axle trailer with ramps;
;
-ONE year of manufacture 1995;
;
Drilling rig GRUNDODRILL 12 GS;
;
-Manufacturer TRACTO-TECHNIK GmbH;
-Type 12 GS drilling bore rig;
-Tractive force 120 kN;
-Thrust 120 kN;
-0-20 ° inclination angle;
-Number of strokes 1000 min-1;
-maximum torque at 130 Umin;
-maximum spindle RPM 70130 Umin;
-Pilot hole diameter 80 mm;
-Diameter percussion drilling pipe TWIN DRIVE 54 mm;
-Impact drill pipe (effectively) 3000 mm long;
-maximum feed speed 0.5 msec;
-maximum diameter of Expander (soil-dependent) ≤ 600 mm;
-maximum pipe of A diameter (soil-dependent) ≤ 450 mm;
-maximum drilling length (depending on the floor) ≤ 350 mm;
-maximum detection depth (depending on the system) 16 m;
-minimum theoretical bending radius 42 m;
-maximum speed 1.2 kmh;
-Fresh water tank 200 liters;
-Drive motor (diesel) HATZ;
-Commercial at 1750 RPM 68 kW;
-Power Max kW at 2400 RPM 80.5;
-Diesel tank 100 litres;
-maximum hydraulic pressure 300 bar;
-Oil tank capacity (oil) 60 litres;
-12 V starter system;
-Sound pressure level LPA according to DIN EN ISO 11201;
-Sound pressure level LWA according ISO 4872;
-Incl. operating instructions;
-Dimensions (Lxwxh) 6160 x 1900 x 2440 mm;
-Weight 8450 kg;
-Boom box weight incl. 48 rods approx. 1600 kg;
-Linkage weight 25 kg;
;
The Grundodrill 12 GS drilling rig is used exclusively for the production of underground tunnels in sand, silt, clay and clay soils with low stone inclusions up to a diameter of 450 mm (depending on the floor).;
The first step creates a pilot hole with the diameter of the drill head.;
In the second step, this pilot bore is so enlarged through special Expander in diameter and pulled into the channel in the continuative piping at the same time.;
A drilling fluid (usually water-bentonite mixture) is used to reduce the soil mechanical resistance during these operations. ;
In addition, the drilling fluid serves as a support medium for the dissolved particles along the tunnel wall to the start - or intermediate pit.;
This procedure is used mainly in the fields of supply:;
-Gas;
-Water;
-Waste water;
-Power;
-District heating;
-Telecommunications;
-Jacket;
Used in PE, steel or cast iron.;
The GRUNDODRILL 12 GS drill is suitable for the following applications:;
-Longitudinal linings,;
-Crossroads of federal highways, highways, parking lots, etc.,;
-Culvert conditions;
;
The drill operates the poles and cutting tools, which create a tunnel through which the product tube is retracted.;
;
Beacon drill track G2;
;
-Manufacturer of Radiodetection CE, continental Europe;
-Monitoring location system of drilling;
;
The drill Track G2 receiver is designed for the requirements of horizontal drilling.;
;
Good used condition.;
For further details on request. Sale as shown (see pictures);
Changes and error in the technical details and information and subject to prior sale.;
Concrete Plant Equipment Suitable for Normal and Lightweight Pallet circulating system for wall elements made of pumice concrete. Formable surface: 1.875x12m, pallets appr. 2mx12.25m. Equipped with: wall elements, 3 cement silos, 1 dry mortar silo, 1 feeding station with bucket el ...
used machine
Pallet circulating system for wall elements made of pumice concrete. Formable surface: 1.875x12m, pallets appr. 2mx12.25m. Equipped with: wall elements, 3 cement silos, 1 dry mortar silo, 1 feeding station with bucket elevator, 5 surcharge silos, mixer for lightweight and normal concrete with lift, mixer for finishplaster from silo, concrete spreader, 2 parallel work stations in the pallet circulating system, separate plasterfinish conrete spreader, 2 vibrating rollers for compacting, heat insulated hardening chamber with shelf control unit and pallet circulation systeml, tilting table, lifting crane 10to, outside crane 10to, various mortar silos, concrete buckets, pallet cleaning unit, old concrete reinforcement bending equipment, metalworking tools.
MECOF35 C RADIAL DRILL Radius: 1105 mm Drilling on steel: 40 mm
Distance :basement-spindle: 1230 mm Spindle taper: 40 Morse
Spindle speed: 1460 rpm Motor power: 2,2 kw
Radius: 1105 mm Drilling on steel: 40 mm;
Distance :basement-spindle: 1230 mm Spindle taper: 40 Morse;
Spindle speed: 1460 rpm Motor power: 2,2 kw
660mm drill bit hammer Augers Not used Drill Bits and Rock Hammers
(total 10units)
(Drill Bit)
Quantity: 8 units
Make: Koken (Japan)
Year: 2005
Hammer type: M160-SD18M150-SD15
Shank type: SD18SD15
Bit size: 660mm(26inch)5 ...
KOBELCO Vertical ground Carroteuse on stretcher Kobelco
vertical ground Carroteuse on stretcher Kobelco
Brand: Custom Machine
Annèe: 2011
Time: +- 1200
Engine: 380 V AC
drilling maximum diameter: 60 cm
Maximum depth: 150 cm
Offset mast: 180
Advancement of ...
used machine
div;
vertical ground Carroteuse on stretcher Kobelcodiv;
div;
Brand: Custom Machinediv;
div;
Annèe: 2011div;
div;
Time: +- 1200div;
div;
Engine: 380 V ACdiv;
div;
drilling maximum diameter: 60 cmdiv;
div;
Maximum depth: 150 cmdiv;
div;
Offset mast: 180div;
div;
Advancement of the mast: 60 cmdiv;
div;
drill column: Adamasdiv;
div;
Track Length: 185 cmdiv;
div;
Overall dimensions of the machine:div;
div;
250 cm x 110 cm x 210 cmdiv;
div;
Dimensions of the cooling water tank:div;
div;
60 cm x 58 cm x 60 cmdiv;
div;
Overall dimensions of the trailer:div;
div;
195 cm x 100 cm x 39 cmdiv;
div;
overall dimensions of the transport chassis:div;
div;
400 cm x 115 cm x 14 cmdiv;
div;
Note: The core drill and not included accessories, generator not includeddiv;
div;
Condition: Good and testeddiv;
div;
div;
HYDRAHAMMERJOY 3 HYDRA JOY 3 Drilling rig Year 2006Serialnumberr H03753Make: Hydrahammer.it3444 hoursCaprari Mudpump (8 bar) - Original pump with 25 bar is still availableEquiped with Rotary head for flush drilling, Rotary head for dry drilling is also available ...
used machine
Year 2006;Serialnumberr H03753;Make: Hydrahammer.it;3444 hours;Caprari Mudpump (8 bar) - Original pump with 25 bar is still available;Equiped with Rotary head for flush drilling, Rotary head for dry drilling is also available;100 meters drillpipe are included, diameter 76 mm, pipelength is 2,5 mtr; ready for operation
FRASTEMultidrill XL MAX Drilling machine Drilling rig - Fraste Multdrill XL MAXEquipment is good working condition and 100 meters drill Pipe are includedType: MDXL MAXYear 2006Total Weight : 11.800 kgPower Diesel Engine 86KW 117 pkPull of Rotary Head Feed Sy ...
used machine
Drilling rig - Fraste Multdrill XL MAX;Equipment is good working condition and 100 meters drill Pipe are included;;Type: MDXL MAX;Year 2006;Total Weight : 11.800 kg;Power Diesel Engine 86KW 117 pk;Pull of Rotary Head Feed System 5000 kg;Thrust of rotary head feed system 3500 kg;Pull of Main Winch 2000kg; ready for operation
CONRAD STANENCONRAD 300 Drilling machine Conrad 300 Drilling Rig mounted on Mercedes Truck type 1717 - 4WD suiteble for Straight flush drilling. Approximately 200 meters drillpipe are included. Equipment is ready for operation.Conrad 300 Drilling RigYOM 1998Dia ...
used machine
Conrad 300 Drilling Rig mounted on Mercedes Truck type 1717 - 4WD suiteble for Straight flush drilling. Approximately 200 meters drillpipe are included. Equipment is ready for operation.;;Conrad 300 Drilling Rig;YOM 1998;Diameter of drilling pipe ; 88 mm;Pump Type CM 490 Liter per Minute 20 Bar;;Mercedes 1717 - 4x4;YOM 1990;98000 km; ready for operation
FRASTEML-MAX Drilling machine Included drill accessories:Drill accessories:- 3 inch straight flush drillpipes, total 112 meter length- 4 inch reverse circulation drillpipes, 17 x 3 meters Straight flush drillings up to 120 meters depth, max. hole di ...
used machine
Included drill accessories:;;Drill accessories:;- 3 inch straight flush drillpipes, total 112 meter length;- 4 inch reverse circulation drillpipes, 17 x 3 meters;;;; Straight flush drillings up to 120 meters depth, max. hole diameter of 150 mm.; Reverse circulation drillings up to 80 meters depth, max. hole diameter of 600 mm.;;Specifications:;;Mast Stroke 4.300 mm; Pull up force 3.000 daN;;Drillhead Thrupass 100 mm; Torque 270 daNm at 110 rpm-540 daNm at 55 rpm;;Straight flush pump Pump capacity 100 m3hr; Pressure 6 bar;Reverse circulation pump Type 4 inch; Pump capacity 180 m3hr;; ready for operation
