universal cnc milling used for sale

x-travel:8500 mm y-travel:2000 mm z-travel:1500 mm rapid travel x/y/z:25 m/min table-size:10.000 x 1.350 mm table load:max. 5 t/qm universal head:orthogonal 1° x 1° tool taper:SK 50 milling head speed:4.000 1/min power capacity:37 kW max. torque on the spindle:900 Nm internal coolant system feed:15 bar control:HEIDENHAIN iTNC 530 Tool changer:60 Pos. total power requirement:75 KW dimensions of the machine ca.:12,7 x 5,2 x 4,6 m weight of the machine ca.:35 t universal travelling column - universal machining center, orthogonal milling head, water-cooled, with 1° indexing in 2 axis (360 pos. in rear layer, 270 pos. in front layer) 3D touch probe M&H 20.41, dividing wall for 2 table machining, internal air blast, 15bar high pressure pump, prepared for HSC milling heads incl. torque support, moveable operator-cabin/panel, chipconveyor, handwheel HR 410, controlled security fence, miscella ...

x-travel:750 mm y-travel:600 mm z-travel:520 mm table surface area:D 700 x 500 mm turning speeds:30000 1/min tool taper:HSK E50 control:HEIDENHAIN iTNC 530 tool change unit:60 pos. rapid traverse:50 m/min table load capacity - central/maximum:350 kg total power requirement:50 kVA weight of the machine ca.:9 t dimensions of the machine ca.:3,2 x 2,65 x 2,8 m 5-axis simultaneously HSC-machining center, NC-round-swivelling table B-axis 180°, C-axis 360°, chip conveyor, prepared for 3D touchprobe HEIDENHAIN TS 641 (without touchprobe), mode 4, spindle chiller, no internal coolant supply, approx. 124.200 hours "machine on", approx. 60.600 hours "spindle on" in total

grinding diameter:600 mm grinding length:3000 mm centre height:315 mm workpiece weight max.:3000 kg work piece spindle speed:8 - 120 U/min grinding wheel motor:25 kW grinding wheel speed:45 m/sec grinding wheel width x diameter:750 x 80 mm table speeds:30 - 4500 mm/min feeds of grinding head:0 - 5 mm/min table swivelabel +/-:7,5 ° total power requirement:55 kVA weight of the machine ca.:18 t dimensions of the machine ca.:11,5 x 4 x 2,2 m - Internal grinding device - taper grinding up to 10,1° based on diameter - automatic grinding cycle - grinding wheels and flanges - dressing device - coolant attachment - dust exhauster, various steady rests

grinding diameter:380 mm grinding length:1000 mm centre height:180 mm grinding wheel diameter:400 mm max. workpiece weight between centres:250 kg total power requirement:10 kW weight of the machine ca.:4,1 t dimensions of the machine ca.:3 x 2 x 1,6 m with internal grinding attachment with fixed and swivelling headstock with coolant tank

Universal grinding machine from Denius, manufactured in 's-Hertogenbosch (NL). Robust machine for the precise sharpening of various cutting tools: milling cutters, drills, reamers, turning tools, etc. Model on a heavy cast iron frame, equipped with a powerful motor and a table adjustable in several axes. Features: Brand: Denius Type: Universal Tool Sharpener Origin: Netherlands Power supply: Three phase (400 V) Cross table with micrometer adjustments Swivel tool holder Upper motor driving the grinding wheel Stable cast iron frame, ideal for precision work Estimated weight: approx. 250–350 kg

End Milling Machine Drill Milling Machine working width mm: 3200 Left - right swivelling saws from 0° - 45°. Complete with drilling unit Suitable for machining doors and door posts.

Univ. Tool Milling Machine DECKEL Type FP 1Masch. No. 33064 Year of construction approx. 1960 Overhauled in 2012Travel distances X: 300 mm Y: 150 mm Z: 330 mmTable size 600 x 210 mmSpindle holder MK 4 - S20 x 2Spindle speed vertical 95-1900 rpm. 12 stepsSpindle speed horizontal 60-1200 rpm. 12 stepsMotor power 1.1 and 1.4 kWNerg connection 380 volts, 50 Hz- Feed in the X and Y axis- Pinol displacement on the vertical milling head- Fixed angle table- Coolant device with mechanical pump in the machine foot-

Milling holders with milling cutters and drills mostly SK40, total 25 parts

End mill, end mill, cutter, shell cutter, milling head, angle cutter, shell angle cutter, angle end mill, prism cutter -Angle milling cutters: Attachment angle milling cutters, prism milling cutters -Type: Ø85 x 35 mm -Hole: Ø 27 mm -Quantity: 1x milling cutter available -Dimensions: Ø 85 x 35 mm -Weight: 0.8 kg

Impex ST-D70E Slot Milling Machine Wall Groove Milling Machine Auction-ID: A7-45427-67

Spit F 40 slot milling machine including accessories and 3 milling machines, wall groove cutter Auction-ID: A7-45427-54

BAIER MF 63i Slot Milling Machine Wall Groove Milling Machine Auction-ID: A7-45427-115

Table clamping surface: 600 x 1100 mm traverse path x: 800 mm traverse path y: 450 mm traverse path z: 500 mm Quill stroke: by hand approximately 50 mm of spindle speeds: 63-3150 rpm stufenl feeds. adjustable: 0,1-1500 mm / min rapid traverse: x/y/z 4.5/2,6/3 m / min. Supply: 380 V, 5.5 kW space: 3000 x 2500 x 2030 mm weight: 4000 kg

Table clamping surface: 500 x 1000 mm stroke x: 630 mm traverse path y: 500 mm traverse path z: 460 mm Quill stroke: hand 45 mm spindle retainer: ISA 40 spindle speeds: 31.5-3150 rpm stufenl feeds. adjustable: 1-3000 mm / min rapid traverse: x/y 6 / z 4 m/min. Supply: 380 V, 6/8 kW space: 1800 x 2120/2600 x 2020 mm weight: 3100 kg

Table clamping surface: 630 ø mm traverse path x: 600 mm traverse path y: 450 mm traverse path z: 500 mm Quill stroke: hand 80 mm spindle retainer: ISO 40 spindle speeds: 20-3150 rpm stufenl feeds. adjustable: 1-3000 mm / min rapid traverse rate: 4 m / min. Connection: 380V kW space: 2000 + 850 x 2000 x 2000 mm weight: 3300 kg

Stroke x: 600 mm traverse path y: 400 mm traverse path z: 400 mm spindle retainer: ISO 40 spindle speeds: 80-4000 rpm stufenl feeds. adjustable: 0,1-1500 mm / min rapid traverse: x & y/z 4/2.5 m / min. Supply: 380 V, 16 kVA kW space: 2450 x 2200 x 1900 mm weight: 2250 kg

5 axis machininng center (milling/turning from bar) multitasking Under power in our warehouse MAKE CHIRON MODEL MILL 800 5 axis CNC Fanuc 18iMBS (5 simoultaneous axis 1) X, Y, Z (mm) 800 ? 500 - 550 Rapids (Highspeed) 60 m/min Swivelling head CNC controlled (B axis) +/- 100° Turning spindle Peiseler Milling spindle 12.000 giri / 140 Nm (v nota 2) Tools 65 Tool type HSK-A 63 DIN 69893 Tool-change time 1,5 sec (v nota 3) Table 1400x500 Max table load 1200 kgs Coolant through spindle 70 bar (see note 4) CNC controlled clamping/rotating unit for 6th face machining (v. nota 5) Pressurised linear encoders Swarf conveyor Renishaw-ready Y.O.M. 2006 Weight 7500 kgs Turning package Max dia 65mm RPM: 15 / 4500 Max 42,5 KW / 90 Nm. Hydraulic clamping 800 Nm. Bar loader ILS-RBK- 10012 65 Diameters min ...

Table size: 460 x 800 mm stroke x: 485 mm traverse path y: 385 mm traverse path z: 380 mm Quill stroke: by hand approximately 70 mm spindle speeds: 50-3150 rpm stufenl feeds. adjustable: 2-1000 mm / min rapid traverse rate: 2 m / min. Port: 3.7/4,4 kW space: 2100 x 1650 x 1730 mm weight: 1850 kg

Vertical machining center Cincinnati Millacron Traverse path x 1270 mm Y: travel 660 mm Z: travel 660 mm CNC control: Acramatic 850SX Table size: 1,370 x 660 mm Table load: 910 kg Rapid traverse x/Y/Z: 15,000 mm / min. Spindle speeds: 60-8,000 rpm. Spindle recording: ISO 40 Distance from spindle - table min/max: 150/880 mm Tool changers: 21 items Equipped with:-cooling device -Hand Council operation -Complete instructions Country of origin: England Spindle motor: 9 kW Machine weight: 8.000 kg Machine WxDxH: 3,600 x 2.900 x 3.000 mm

Tool to CNC milling center Steep cone-cone SK 40 Vsadrq with tightening bolt Tool according to the pictures flat rate EUR 6980.00 Built in 2003 In good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Control: Heidenhain TNC 360 (1992) Table size: 1000 x 1000 mm Table size with front extension: 1345 x 1000 mm Table load max.: 2000 kg Distance spindle centre to column min/max.: 270 ~ 1270 mm Distance spindle nose to table min/max.: 0 - 1100 mm Distance between the upright columns: 1855 mm Table longitudinal travel : 1400 mm Boring ram carriage cross travel: 900 mm Crossrail vertical travel: 850 mm Boring spindle travel: 370 mm Spindle motor rating: 6 KW Spindle speed range: 30 - 1500 rpm Boring spindle diameter: 82 mm Spindle taper: MK 5 Borer diameter: 2 - 70 mm Boring tool diameter: 17 - 450 mm Boring diameter in solid ST 60: 45 mm Boring diameter in solid Cast iron: 70 mm Equipped with: Tooling; Accessories Machine overhauled and retrofitted in 1992 !; Very good

Vertical Milling Machine RAMBAUDI type RAMMATIC 600 Travel X 1260 mm Travel Y 690 mm Travel Z 600 mm Numerical Command NUM 1060 Cone SA 50 Table size 2000 x 600 mm Year of construction 1991 Voltage 380 V Depth 2500 mm Total height 4000 mm Weight approx 9 T

CNC controlled 3 axle system a 3 axis system for various Aufgaben(wie Fraesen, Bohren, gravieren, Handhabung, Lasern, Laborarbeiten, etc.) X-Y axes are created by IEF. Traverse paths x 200 mm, Y: 320 mm Z axis (FESTO) operated pneumatically. Stroke Z: 95 mm 4 x supports height 330 mm Control IEF, PA control Alu-Profilrahmen(4x4cm) with 4 doors with automatic locking system. Dimensions: L x D x H (CA. 1390 x 990 x 2000 mm) Aluminum table top Cabinet

With CNC control, HEIDENHAIN, Type: TNC 155, measuring taster Separate control cabinet: 1260 x 500 x 1700 mm Travel distances 700 x 550 x 550mm Table area 1000 x 490 mm Accessories: Treatment / Cooling system / tool shots The machine stored since 2013. At the time of storage, the machine was fully functional.; ready for use

A used S O R A L U C E CNC driving stand milling and drilling center FS 16000 Built in 2000 MAIN TECHNICAL DATA: Travel: Longitudinal (X): mm 16000 Senkr. (Z): mm 1600 Cross (Y): mm 1500 Milling and drilling spindle: Tool holder: ISO 50, DIN 69871 Auto. Tool tension: clamping force 15000 N Tightening bolt: DIN 69872 Form B (BT50) Spindle speeds: Special speeds: rpm 20-3000 Feeds: Feed range: mm/min 2-5000 Rapids: X-axis: mm/min 12000 Y- and Z-axis mm/min 15000 The machine is equipped with: - HEIDENHAIN control TNC 426 M. - Operator's platform in the X-direction with sliding door and Viewing windows against chip flight and splashing water. - Operator's console swivels mounted on the stage. - Automatic thermal expansion compensation of the Milling sliders. - Automatically indexing milling head. This milling head enables the fully automatic m ...

Milling Machine MAHO MH 700 C CNC- 5 axis CNC- Phillips 432 X/Y/Z- 700/450/500 mm B axis CNC Universal table 820x480 mm 5th axis- CNC/NC dividing head ISO 40 spindle adapter Quill stroke of spindle 100 mm Universal table: -swiveling of the Horizontal X/Z axis 30 degrees -swiveling of the vertical Y axis 360 degrees Spindle speeds infinitely variable 20-3150 rpm

Spindle diameter 203.2 mm x-travel 9,000 mm y-travel 4,000 mm Grinding spindle diameter 335 mm Spindle holder ISO 60 Spindle speeds 1-350 / 5-1,200 rpm w-axis 800 mm z-axis 1,200 mm Rapid x-axis 8,000 m/min Rapid y-axis 6,000 m/min RAM Dimensions 530 x 600 mm Main drive 75 kW Total power requirement 165 kW Machine weight approx. 130 t Space requirements approx. 16 x 5.5 x 8.1 m Addition: - hydrostatic guides in x-, y- and w-axis - Telescopic cover for the X-axis of the bed - cumulative Z and W axes - Leveling shoes - Platform Y axis

Mikron C Axis Machine Table - with Heidenhain control 430 - Siemens server motor - Table: 60 x 110 cm - 4th axis, diameter: 50 cm - Weight: 650 kg Good condition fully functional can be visited and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article, in order to avoid misunderstandings, can be viewed before the purchase and tested under electricity. Please ask questions before buying to avoid ambiguity. For general questions or an appointment for a viewing, I can be reached at any time at the telephone number below or above. Errors in the description and prior sale excepted. VAT will be shown separately on my invoices. Shipping with freight forwarder.

Travel X-axis 19,000 mm Y-axis 3,500 mm Z-axis 1,000 mm W-axis 1,000 mm V-axis 2,500 mm B-axis 360°/ 0.001 Table size 4,000 x 3,500 mm Maximum permissible weight on the table 65 t Spindle diameter 160 mm Mounting cone in spindle 2079 DIN/ ISO 50 Spindle speed 2.5 - 1,000 rpm Spindle motor power 90 kW RAM cross section 400 x 400 mm Automatic tool changer 60 positions Feed in all axes 1 - 6,000 mm/min Rapid response in all axes 10,000 mm/min Automatic indexing 360,000° Plate field 12,750 x 6,000 mm CNC, electrical and mechanical overhaul by Siemens in 2003

2130 2x3 M 3D CNC milling plotter built in 2014 in China, is used for machining workpieces in the X,Y and Z axes. Machining is performed on the machine’s vacuum table with dimensions (L x W) of 3000 x 2100 mm, by using a rotary head. The applied electro-spindle with a power of 4.5 kW, is distinguished by its extreme reliability and speed reaching up to 18000 rpm, allowing the desired result to be obtained in a very short time. The CNC milling machine is controlled by a hand-held terminal connected to the WEIHONG NK105 G2 CNC controller. This solution makes the machine’s operation much easier to handle and allows every function to be used. The machining centre is also equipped with among others: an EMI filter to attenuate high-frequency electromagnetic interference and a PANASONIC MDME102GCGM axis servo motor. Technical specifications of the 2130 2×3 M CNC milling machine - wo ...

Travel X-axis 9,500 mm Y-axis 4,100 mm Z-axis 950 mm W-axis 900 mm Main spindle speeds (infinitely adjustable): 3.15 - 1000 rpm Spindle motor power 58 kW Feed speed (infinitely adjustable): X-axis 0.1 - 9600 mm/min Y-axis 0.1 - 5600 mm/min Z-axis 0.1 - 5600 mm/min W-axis 0.1 - 5600 mm/min Accessories: Plate field: 6 x 4 m (CNC-controlled B- and V-axis) Table: 2 x 2 m (CNC-controlled B- and V-axis)

x-400,y-330,z-350,angle table 630x335,SK 40, 40-6,000 rpm,measuring probe

SERON 1315 EXPERT CNC milling machine built in Poland in 2017 is new and has never been used. The machine designed and manufactured with attention to the smallest details, is used for precision machining of a wide range of materials such as mild metals, plastics, carbon, wood, wood-like panels and glass. All vibrations and deformations during the milling process are eliminated by the high-quality ribbed steel construction with a T-slot table made of aluminium profiles, with a length of 1500 mm and a width of 1300 mm. The workspace is additionally equipped with a special PVC overlay to protect the table cover while cutting the workpieces through. At the end of the table there is a six-position linear magazine with an automatic tool correction sensor. The 1315 EXPERT machine axes are driven by highly dynamic and precise brushless AC servo drives with back pressure, equipped with serv ...

5 axis machininng center (milling/turning from bar) multitasking Under power in our warehouse MAKE CHIRON MODEL MILL 800 5 axis CNC Fanuc 18iMBS (5 simoultaneous axis 1) X, Y, Z (mm) 800 ? 500 - 550 Rapids (Highspeed) 60 m/min Swivelling head CNC controlled (B axis) +/- 100° Turning spindle Peiseler Milling spindle 12.000 giri / 140 Nm (v nota 2) Tools 65 Tool type HSK-A 63 DIN 69893 Tool-change time 1,5 sec (v nota 3) Table 1400x500 Max table load 1200 kgs Coolant through spindle 70 bar (see note 4) CNC controlled clamping/rotating unit for 6th face machining (v. nota 5) Pressurised linear encoders Swarf conveyor Renishaw-ready Y.O.M. 2006 Weight 7500 kgs Turning package Max dia 65mm RPM: 15 / 4500 Max 42,5 KW / 90 Nm. Hydraulic clamping 800 Nm. Bar loader ILS-RBK- 10012 65 Diameters min ...

Micron WF 61 C Equipped with a controlled round table Workspace X-axis: 800mm Y-axis: 500mm Z-axis: 460mm Table: 1000 x 500mm Number of working spindle speeds: 21 Speed range 40-4000 rpm Pinole movement vertical: 90mm Feed speed in all 3 axes: 1-3000 mm/min

Mikron VCP 800 2007 Built in 2007 Control Heidenhain iTNC 530 Travel X-800mm , Y-650mm , Z-500mm Working spindle: Spindle speed max. 12000rpm. Tool magazine: Number of tool slots 36 Machine table: Clamping area 800 x 650mm Accessories: Inner coolant supply - Belt filter system 20Bar Conveyor

Lid Maho DMC 80 U hi-dyn Workspace: X-axis: 800mm Y-axis: 700mm Z-axis: 600mm Workpiece weight: 800 kg Number of axes: 5

5 Axis Lid Maho DMU 200 P Built in 2000 The machine is in very good condition. Videos under power available ! Technical data: Travel: X 1800 mm Y 2000 mm Z 1100 mm NC Round Table: Table area: 1700 x 1400mm Permissible load: 5000 kg Number of grooves: 11 Axis (swivel range) : 360 x 0.001 degrees Motor spindle: 8,000 rpm (SK50) Tool holder: SK 50 Tool changer: 60 seats Max tool weight: 20 Kg Max tool length: 450mm Max tool diameter: 110mm

DECKEL MAHO DMU 100 T YEAR OF CONSTRUCTION: 2001 - Number of axes: 5 ( simultaneous) milling spindle - Tool holder: SK40 - Spindle drive power: 15 [kW] - Spindle speed: 20 - 12,000 [up] LINEAR ACHSEN - Travel X/Y/Z axes: 1,060 x 710 x 710 [mm] - Rapid speed (X/Y/Z) : 30,000 [mm/min] - Feed speed (X/Y/Z) : 20 - 15,000 [mm/min] SCHWENKACHSE A : SCHWENKKOPF - Travel: 90 [degrees](+/-) - Minimum resolution: 0.001 [degree] SCHWENKACHSE B : NC ROUND TABLE x 800 [mm] - Travel: 360 [degrees](+/-) - Minimum resolution: 0.001 [degree] WERKZEUGWECHSLER - Number of tools in the magazine: 32 ( 2x 16 places) table - Table size: 1500 x 795 [mm] - Loading table max. : 500 [kg]

Matsuura MC600VF Vertical Machining Centre in great working condition ready to use. COOLING TROUGH SPINDLE YEAR: 1997 with Yasnaz i80M Control, Table size 870 x 400mm, 20 Position ATC, BT40 Taper, Spindle Chiller, Coolant Tank, X = 600 Y = 410 Z = 470mm, Spindle Speeds 30 – 8000rpm. S/No. 970112285 including Large Qty of BT40 Tooling (33 TOOLS, Universal 3D Tester. Country of Origin: Japan. INCLUDED AS WELL BACK UP PARAMETERS.

Milling machine 4-axis (15995740874) DMG Milltap 700 (2015) Spindle 24,000 1/min NC parts apparatus Lehmann EA-510. L Tool magazine 25 places Renishaw Measurement Kit Rinsing gun Milling machine 5-axis (15995747284) DMG Milltap 700 (2015) Spindle 24,000 1/min Swivel rotary tables 5-axis simultaneous operation Clamping pneumatics 1-circuit Tool magazine 25 places 40 bar IKZ Conveyor Rinsing gun Renishaw Measurement Kit Milling machine 5-axis (15995765944) DMG Milltap 700 (2018) Spindle 10,000 1/min Swivel rotary tables 5-axis simultaneous operation Clamping pneumatics 1-circuit Tool magazine 25 places 40 bar IKZ Conveyor Renishaw Measurement Kit Automatic front door Automation interface including automation door on the right Milling machine 5-axis (15995734744) + WH3 (770200062R) DMG Milltap 700 (2014) Spindle 10,000 1/min Swivel rotary  ...

Model MC-800VF WITH 4 TH AND 5 TH AXIS FIRST TIME IN USE FROM 1996 Brand MATSUURA Type Vertical Machining Centers Control CNC (Yasnac i80 CNC control) Table 1200mm x 400mm Power 15 hp RPM 12000 rpm ATC 30 Taper BT40 Axis 3+2 Weight APROX 7000 KG TRAVELS: X = 800mm, Y = 440mm, Z = 485mm mfg MATSUURA mpn MC-800VF Matsuura MC-800VF WITH 4 TH 5 TH AXIS MACHINE WAS WORKING IN ROLLS ROYCE FROM A NEW AND IS GREAT MANTAINED HAS NEW BATTERIES, BACKUP MADE.

Milling machine lid FP 4 NC Built c. 1992 with controlled C-axis 2 pieces of screw sticks Various tool holders Machine is in top condition and was last serviced on 20.08.2020 for approx. 3.000,- € (net). documents available. The machine is sold only because of space requirements. Location of the machine: 76661 Philippsburg

Parcels of 7 machines 1x CNC 5 axis milling center, brand Okuma, type MU 400 VA, built in 2004, with various accessories and tool holders 1x CNC 5 axis milling center, brand DMG, type DMU 50/60, year of construction, 1996 with various accessories and tool holders 1x CNC 3 axis milling center, brand Okuma, type VR 40II, year of construction, 1995 with various accessories and tool holders 1x CNC 4 axis milling center, brand Okuma, type MC 40VA, built in 1991, with various accessories and tool holders 1x tool adjuster, Make EZSET Type 400 1 x Schumpfgerät, Brand Heimer, Type Power Clamp, Year of construction 2019

ATMSolutions ATMS 1325 CNC milling machine built in 2017 in Poland is designed for the production of both small and large parts made of e.g. aluminium, plastic or wood. The machine on offer is like new, it has never worked after a trial run. The machining process is performed on a large vacuum table using a powerful, water-cooled spindle. The steel frame, by increasing the overall rigidity, makes it possible to achieve unprecedented precision and accuracy in machining, removing any vibration and deformation. In addition, the X and Y axes are equipped with trapezoidal guides with gear drives with bevel teeth, thanks to which excellent dynamics and feed repeatability are achieved. This is complemented by an intuitive CNC control with professional CAM software that supports G-CODE and .nc commands. The ATMS 1325 CNC milling machine weighs 1000 kg. Technical specifications of the ATMSo ...

Machine details Stock number 1105-03328 Machine type tool milling machine - Universal Make MAHO Type MH 800 E Year of construction 2000 Control type CNC Storage location FRANCE Country of origin Germany Delivery time immediately Freight base from stock price Technical details x-path 700 mm y-way 550 mm z-path 500 mm Speed 20 - 5000 rpm Tool holder SK 40 Quibola stroke vertical 80 mm Feed 1 - 5000 mm/min Rapid speed 6000 mm/min Table size 900 x 550 mm Total power requirement 16 KVA Weight of the machine ca. 7 t Space requirement approx. 2.4 x 2.85 x 2.1 m Information - with web control CNC 532 - with FIXED ANGLE TABLE WITH TOOL CHANGER - Enclosure Machine under power Ready for demonstration.

Cover FP2 FP 2A SK40 / with dialog 11 path control Control: CNC Dialog 11 - 3D Web Control Speed: 40 - 4000 rpm Feed rate: 2 - 3600 mm/min infinitely variable Rapid speed: 4 m/min Drive power: 1.6 / 2.0 kW 1400/2800 rpm Quill: Extendable quill vertical 80 mm SK40 with Clamping system DIN 2080 Travel: X/Y/Z: 300/300/400 mm Rotary table: 3 axis Universal table 600 x 330 mm max load 250 kg Equipment: Hydromechanical clamping system SK40 with suit bolt DIN 2080. Vertical & Horizontal spindle , Milling head manually swivel+/- 90 ° Machine light Programming: Dialog-guided programming with cycles. E-handwheel.

Deckel Maho DMG DMU 70eVolution 5Axis simultaneous Machining center CNC Hersteller [manufacturer]: DMG Deckel Maho Type [ type]: 70eVolution Control unit: Heidenhain iTNC 530 Incl. handwheel Baujahr[construction year]: 12/2006 - Renewed/renewed spindle - IKZ integrated cooling system for water 40bar and air (both possible) Travel X/Y/Z 750/600/520 mm B-axis 0 to 180° degrees C-axis n x +-360° degrees Table load up to 350kg Spindle speed range 20 to 18,000 1/min. Tool holder SK 40 DIN 69871 Weight [weight]: 10.000kg Full documentation is available. Inspection under power can be done at short notice. We will be happy to answer any further questions you may have. Tel. 017621834834Price, from stock here plus VAT Condition: good - ready for demonstration Delivery: from stock - as seen Payment: purely net - upon receipt of invoice Prior sale, errors excepted.  ...

Code 0739 DESCRIPTION CNC Universal toolroom milling machine Make Maho Model MH 700 C S/N 75915 Year 1984 Control Philips CNC 432 Table 900 x 500 mm Longitude ( X – axis ) table 700 mm Vertical ( Y – axis ) table 450 mm Cross ( Z – axis ) spindle 500 mm Spindle out ( H/V ) 100 mm Max. distance table / spindle horizontal 700 mm Max. distance spindle / table vertical 500 mm Spindle taper 40 ISO Speeds 20 – 3150 rpm Feeds X-Y-Z 1 – 3000 mm/min Rapides 6 m/min Spindle motor 8 kW - 380 Volts Accessories Table 900 x 500mm Condition Machine is in good condition