129,253 used machines on RESALE, but how to find them? Machine Search
One complete and one partially dismantled extruder system Davis are available. 1) Davis Standard DS-25, power: 6385W, max. melt pressure: 700bar, max. temperature: 315°C. Including 4x screws, 6x bursting discs, Digicolor dryer, platform, screen changer with heating and sealing pack, new cylinder, 3x screw seals, and spare drive motor. 2) Davis Standard DS-20, power: 4500W, max. operating pressure: 700kg/cm², max. temperature: 315°C. Including Conair dryer, 3x screws, screen changer with heating and sealing pack, cast housing, extrusion tool, and spare drive motor. General accessories: various ring heaters, 3x Eurotherm temperature controllers, and 3x Eurotherm pressure sensors. Documentation available. An on-site inspection is possible.
A complete PS foam extrusion line (capacity: 350kg-400kg/h) is available. 1) 7x dosing units K-Tron Switzerland and Coperion, main components: 3, side components: 4, capacity: 350kg-400kg/h. 2) Primary extruder Battenfeld, year of manufacture: 1998, screw diameter: 120mm, screen changer: Gneuss, double piston pump: LEWA. Including gas injection. 3) Secondary extruder, screw diameter: 150mm/33D. Including unused old die and a coextruder Kühne with 50mm screw diameter. 4) Oil-heated Sunwell round die. 5) Calibration unit Dorn, knives: 2, films: 2, film width: 1080mm. 6) Take-off unit Gloenco Double S Haul-Off. 7) PS film winder, positions: 4, simultaneously operated positions: 2, winding speed range: 10m-30m/min, roll weight range: 150kg-300kg, roll length range: 500mm-800mm. Including discharge with ionization. Documentation available. An on-site inspection is possible. This line is sold ...
Deze machine staat in opslag bij Plastima Used Machinery Blo Udevcqccs Dvycop
Werkend uit productie, heeft altijd gelopen met een 800 mm extrusiekop voor het produceren van HDPE buizen. Bwj Uswr Db Nod Dvycjw
Deze extruder lijn van Kuhne staat bij Plastima Used Machinery in de machineopslag. De machine komt uit 2008 en verkeerd in prima staat. Merk: Kuhne GmbH Model: K 60E - 33D Typen schroef: enkelschroef Bouwjaar: 2008 Schroef Ø: 600mm L/D-verhouding: 33 Hoogte cyclinder: 425 mm Bls Ud Dou Etygevycep Kegelhoogte: 325 mm Total height: 750 mm
Brand Collin Lab & Pilot Solutions GmbH Type E 30 M Low Boy Type Screw Single Year of manufacturing 1999 Screw Diameter 30 mm Screw L/D 25 Dimensions (LxWxH) 2.000 x 1.200 x 1.900 mm Weight 560 kG Bwo Ud Dvyew Awczjcsw
This extruder from WEBER is located in the machine storage at Plastima Used Machinery. The machine is from 1997 and is in excellent condition. Brand: Hans Weber GmbH Model: NE 7 048 Screw type: Single screw Year of manufacture: 1997 Screw diameter: 75 mm Be Ud Detpg D Uovyceww L/D Ratio: 30 Operating hours: 76,200
WEBER buisextrusielijn inclusief: Bws Ud Dvysvryhyscsw WEBER DS 8.5 Elmepla zaag Battenfeld R200/6 Battenfeld V125
Deze extruder van WEBER staat bij Plastima Used Machinery in de machineopslag. De machine komt uit 1983 en verkeerd in prima staat. Bwj Ud Djq Tr Tbevycow – Merk: Hans Weber GmbH – Model: ZE 30 – Bouwjaar: 1983 – Enkelschroefs extruder – Schroef Ø: 30 mm – verhouding: 20 L/D
Brand: Collin Lab & Pilot Solutions GmbH Model extruder: E 30 M Low Boy Type screw: Single screw Screw Ø: 30 mm L/D Ratio: 25mm Working hours: 17.620h Year of manufacturing: 1999
Sale of spare parts of EEK 125.22 V, including vacuum cylinder, screw and V-pump, 6 x TCU, Power cabinet with FU 165 KW
Brand: Hans Weber GmbH Model: ZE 20 Type Screw: Single screw Year of construction: 1999 Screw diameter: 20 mm L/D ratio 20 L/D Motor power: 3 kW Control Voltage: 200 V Dimensions (LxWxH): 3100 x 1200 x 1280 mm Weight: Approx. 300 kG Other: – Including swivel mounting arm – Including extra connection box
Prealpinaa 180 mm. 35 L/D (under reconditioning), for HDPE LDPE LLDPE PC PP PS ABS, Offered totally reconditioned with warranty, The line includes:, (OPTIONAL - Buffer silo with agitators and feeding auger), forced feeding unit, extruder with NEW barrel and 180 mm NEW screw 35 L/D, vacuum degassing system, 397 kw d.c.drive, semi-automatic screen-changer with 300 mm diam. screens. (can be fitted with fully automatic screen-changer), water ring pelletizing unit, heat exchanging units on pelletizer and gearbox, drying centrifuge, vibro-classifier, NEW electric cabinet with PLC and touch screen display (or traditional commands, if preferred), throughput rate 1.000-1.400 kg/h depending on scraps and feeding rate, installed power 650 kw, used 420 ca in work, Users manuals, drawings, CE., Delivery : about 13 working weeks for total reconditioning, See how we recondition [HERE](.germanplast.eu/p ...
Extruder for the production of packaging chips Year of manufacture: 1994 Screw: four-course Cylinder: 2-pass Nozzle plate "FLIPS/balls diameter 4mm/1-fold Cutting device with 4-blade cutter head Dosing and suction device Machine is electrically connected, dry running possible Spare parts: 2 4-pass screws, 1 nozzle plate
This ROLBATCH RBSDMS-IZS-678 was made in 2016. It is equipped with a Mill PLC control unit. The machine has a maximum film thickness of 0.3-1 mm.
This SWISS CAB KMV was manufactured in 2001. It is a pipe extruder designed for plastic-metal composite pipe systems. More technical details will follow soon. Consider the opportunity to buy this SWISS CAB KMV pipe extruder. Contact us for more information.
- Brand: GESTER - Model No.: JR75 - Production 50 kg/h - Power: 15 hp (11 KW) main engine - Spindle diameter: 75 mm
- Brand: GESTER - Model No.: JR110 - Production 100-150 kg/h - Power: 55 hp (40 KW) main engine - Spindle diameter: 110 mm
GT-5413 Pellet Extruder - Brand: GESTER - Model: PE YT-75 - Production 40 - 60 kg/h - Power: 20 hp (15 KW) main engine - Power: Auxiliary engine 5.5 hp (4KW) - Weight 800 kg
GT-5414 Pellet Extruder - Brand: GESTER - Model: PE YT-90 - Production 60 - 80 kg/h - Power: 25 hp (18.5 KW) main engine - Power: 7.5 hp (5 KW) auxiliary engine - Weight 1200 kg
Manufacturer: Kowin Model: 232 Machine 1 : - Operating hours 0 - Year of Manufacture: 2024 Machine 2 : - Operating hours the machine donsen´t show operating hours . The machine was only doing g 10-15t of regrind per month from 2011 till 2024 - Year of Manufacture: 2011 Find more here - / Contact us at -
PLASTIMAC LAB EXTRUDER, for blown film, suitable for testing granulate, 25 mm screw diameter, 70 mm diam. die, 500 mm collection frame, 7,5 Hp drive, complete wuth supporting structure, (corona treatment+small printer can be sold separately if required), installed power - used power in work: about 60-65% : 7,5 Hp, working width: 500 mm, conditions: good
Leda Mattiello Extrusion line 160 mm 50 LD 2 degassing pumps, under refurbishing, ENERGY SAVING IR heaters, for PP PS PE ABS PC, etc., Very good quality extruder, 3 m3 ca. storage silo, crammed vertical screw for light materials with adjustable speed,, extruder with 160 mm. screw, 50 L/D, n.8 Infra Red Petrelli Heaters x 11 kw each V.380 - for great energy saving, 315 kw a.c.Sever drive with inverter (about 60% power used in work), Gefran inverter, n.2 vacuum degassing pumps, semi-automatic screen-changer 320 mm Ø screens (possible configuration with fully automatic scren-changer), horizontal water ring pelletizer - or different, drying centrifuge, closed water cycle, Zambello gearbox with oil recirculating pump, oil-water heat exchanging unit, Control cabinet for managing the whole line including thermoregulators, etc., Nominal throughput rate 800-900 kg./h depending on material., The ...
BLOWN FILM LAB EXTRUDER, suitable for testing granulate, 25 mm screw Ø 25 L/D, 60 mm diam. die, 500 mm. pull off, 350 mm collection frame, 7,5 kW drive, complete with tower, nips and rolls, control panel, production rate 10 kg/h, installed power - used power in work: about 60-65% : 7,5 kW, working width: 350 mm, conditions: checked
A Lenhard extruder for butyl rubber is available. Application: insulating glass production, material: thermoplastic butyl based on polyisobutylene, max. operating temperature: 140°C, max. butyl pressure: 140bar, max. hydraulic pressure: 150bar. An on-site inspection is possible.
Haendle Extruder type PZG60b/50 with doubleshaft mixer MDVG920a, 29 cbm/h, 30 bar
Connected load 11.5 kW, extruder screw diameter 32 mm, 3 heating zones, heating time approx. 20 min, potting temperature 0-280 °C, incl. TORO-Systems TR Dry-Jet granulate supply Auction-ID: A7-45263-20
BLOWN FILM LAB EXTRUDER, suitable for testing granulate, for LDPE and HDPE, die diam.97 mm., 800 mm wide single winder, fixed pull off, fixed die head, Maximum throughput rate 35 kg/h, height of pul off 3.700 mm from ground, installed power - used power in work: about 60-65% : 7,5 kW, working width: 350 mm, conditions: checked
CDM PREALPINA 500-600 kg/h, Materials PE PP PC PS ABS PA, extruder with 130 mm. screw diam. 35L/D, a.c. 283 kw drive, Constructed in 2013, crammed feeding unit, extruder 130 mm., one degassing pump 5,5 kw, fully-automatic screen changer FIMIC RAS 400, water ring pelletizing unit, drying centrifuge, heat exchanging unit, vibrating screen, electric cabinet, machine offered reconditioned, installed power - used power in work: about 60-65% : 435, availability: Subject to unsold, conditions: Totally reconditioned, options available: Fimic or non stop screencganger + buffer silo or loading screw+hopper + crammed feeder with buffer silo synchronized with horizontal screw, used power in work: 280 kw, cooling: 13.400 Kcal/h, MATERIALS: PE PP PC PS ABS EPS XPS EPP, delivery time: 30 days ca
Pipe screw, cement screw used without motor for the conveyance of cement or similar materials with directly attached bearings Total length: 6520 mm Screw aisle length: 6130 mm Screw aisle: 210 mm Shaft of 80 mm, slope progressive at the inlet Opening opposite the driven side: inside 210, flange 280 mm Opening 1 driven side: 250 mm Opening 2 (with lid) diameter: 200 mm Matching motor and overhaul can be offered optionally. Drive via flange motor with coupling
A very well preserved VML 18 R screw compressor unit is offered. The screw compressor has the following performance data: Air volume 15.82 m³/min P2e 1.8 bar. The electric motor has a power consumption of 55 kW. If you have any questions, please do not hesitate to contact us.
A very well preserved VM 8 R screw compressor unit is offered. The electric motor has a power consumption of 30 kW. If you have any questions, please do not hesitate to contact us.
A new replacement level type VMX 110 RD is offered see pictures. If you have any questions, please do not hesitate to contact us.
On offer is a very well-preserved VM 8 R screw compressor unit. The electric motor has a power consumption of 30 kW. If you have any questions, please feel free to contact us.
A new replacement stage type VMX 110 RD is offered, see pictures. If you have any questions, please feel free to contact us.
Pneumatic screwdriver, pneumatic screwdriver DESOUTTERDrück air screwdriver, rod screwdriver for screwdriving technology type SD 140-AR510-S4QDreh torque range: 0.6-14.0 NmSpeed: max. 510 rpm. Compressed air requirement: 6 barAir consumption: 8.7 l/sBit input: M6- rotary switch for clockwise and counterclockwise rotation (rotary ring control)- without screwdriver shutdown- compressed air control cable 4 mm- compressed air connection for screwdriver function min. 10 mm- Aluminum bracket for handling device- Screw feeder 12 mm (inner diameter)Dimensions L x W x H
Screw block for screw compressor, compressor, compressed air unit, stationary compressed air compressor, screw block, compressor, compressor stage -Manufacturer: Boge, screw block compressor stage from compressor type SL 270 -Screw block: type BS 430 -Final pressure: max. 15.0 bar -Hole circle: Ø 295 mm / M20 / Ø 740x22 mm -Shaft: Ø 100 x 200 mm -Dimensions: 1200/850/H790 mm -Weight: 917 kg
Screws, hex bolts, flange nuts, hexagon nuts, collar nuts, solar fasteners, cylinder screws -Hex bolts/cylinder bolts: M10 stainless steel 330 kg -Hexagonal screws: DIN 933 M10 x 100 300 pcs / M10 x 20 4400 pcs -Cylinder head screws: DIN 912 M8 x 35 6600 pcs / M8 x 30 4200 pcs -Material: Stainless steel A2 -Price/Sale: complete -Transport dimensions: 1200/800/H200 mm -Total weight: 330 kg
Screws, hexagon screws, flange nuts, hexagon nuts, collar nuts, solar fasteners, cylinder screws -Hexagonal screws/cylinder head screws:M16 / M20 730 kg -Hexagon screws: DIN 931 8.8 M20 x 60 250 pieces / M20 x 55 DIN 933 8.8 4400 pieces. -Hexagon screws: DIN 931 8.8 M16 x 50/22 150 ST -U-washers: Ø 21.0 mm DIN 125 Form B 2100 pcs. -Price: complete -Transport dimensions: 1200/800/H440 mm -Total weight: 730 kg
We offer all types of screw manufacturing machines M3 - M25 -A href=inchabc://abc.steinfels-kg.de/sale/screws/inch>all information about the machine please click here
We can offer you all types of screw making machinery for M3 - M25
M18L - 1 Screw Head Slitting Machine (used) without vibrating conveyor Make: MENN - Type: KS8 and KS5 Diameter range 1.7-10 mm Shank length under head 3-105 mm Power Piece/Min 27-1.850 Weight 800 kg Engine power 1.5 kW
maximum number of results exceeded
please refine your search
1.500 € 
