turning machines used for sale

Control : Heidenhain Peak height 260 mm Tip width 1500 mm Turning over bed 520 mm Turning diameter via slide 310 mm Travel -Z Axle 1250 mm Travel -X-axis 270 mm Width of the lathe bed 400 mm Spindle holder CL 8" Spindle bore 110 mm Spindle speeds 0 - 2000 rpm. Rapid speed X/Z 5 m/min Pinien travel by hand 220 mm Pinole diameter 80 mm Pinole holder MK 5 Total installed power 18 kW (Electronically reduced) Engine hours 1828 h

Ladies and gentlemen, below we offer the following machine for sale: from a tool making, single-layer run and very well maintained. Still under power. CNC lathe Voest - Alpin - Weipert WNE 490 X 1000, peak height 240mm, tip width 1000mm, control Siemens, circulating through mes.over bed 490mm, circulating permes.via plan slide 195mm, crimping 520mm, Spindeldurchmes.im front. Bearing 100mm, spindle bore 63mm, torque 736Nm.

Plate diameter 4200 mm Maximum turning diameter 4600 mm Max workpiece height under the cross member 4000 mm Max workpiece weight 100 t Travel RAM horizontal 2600 mm / min Travel RAM vertical 2000 mm / min Tool holder (powered tools) ISO 50 Table speed 40 rpm Main drive 120 kW Number of gear stages 4 Total connection value 180 kW Max torque on the flat disc 40000 kpm Max cutting force per support 10000 kp Crossbar support right and left Largest vertical path of the Chisel slider 2000 mm Cross-section of the chisel slider 285 x 310 mm Adjustment path of the crossbar 3500 mm Total weight of the machine 115,800 kg Accessories Automatic lubrication of the cross-bar guide on the stand Hydraulic weight compensation of the chisel sliders Milling spindle and C-axis c-axis 360,000 positions

Table diameter 2,000 mm Max. Turning diameter 2,150 mm Turning height 1450 mm Table speed 3-140 rpm Max. weight of the workpiece 12000 kg Milling spindle: Maximum speed 2,000 rpm Milling spindle Motor power 22 kW Total weight of the machine approx. 34,000 kg Machine complete with: C-axis: 360,000° Milling spindle 22 KW Tool changer 16 positions Tool changer for milling tools ISO 50 16 positions Complete cladding Conveyor Complete cooling system with filtration

Center height 660 mm Distance between the centers length 12000 mm Turning diameter 1320 mm Turning max. via support 950 mm Clamping max. 1200 Power 55 KW Torque 35000 Nm Bezel I 200-630 mm Workpiece weight 21 to Accessories: Conveyor

Center height 660 mm Center width 11000 mm Turning diameter 1320 mm Turning max. via support 950 mm Power 55 KW Torque 35000 Nm Clamping max. 1200 Workpiece weight 14 to Accessories: Bezel 200-630 mm

Turning + Thread cutting semi-automatic M32 The machine was never used for production. Suitable for internal and external threads max. diameter 90 mm max. turning length 45 mm max. thread pitch 1.5 mm max. thread length 14 mm Max. Thread pitch multi-speed 3 mm largest thread length multi-speed 21 mm Drive motor approx. 3 hp Machine weight 800 Kg

Parallel lathe Geminis GE650S to be rebuilt. Distance between points: 1000mm. Flip on bench: 680mm. Flip on cart: 410mm. Flip over neckline: 850mm. Main hole: 84mm. Motorized trolley and charriot. Speeds: 18 (13-1000rpm). Main engine: 15hp. Plate and trolley protections and CE RD1215/97 certificate. Quick-change plate and turret.

Bendless automatic lathe make INDEX type E 60Fabr. -No: E 6072107 Year 1972largest material passage: 60 mmChuck diameter: 136 mmmax. thread diameter: M 30 / M 24Speed range: 134 - 2420 rpm.Working distance: 80 mmRapid traverse path: 50/62 mmlargest longitudinal path: 80 mmDistance quill to collet: 60 - 230 mmFeed infinitely variable: 5 - 3400 mm / minDrive power: 5.5 kWDimensions L x W x H: 1510 x 850 x 1500 mmWeight approx. 2000 kgWith- bar feed- various change wheels- hydr. Power Chucks- long turning device- Copy machine Fabr. SauterusedPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Single spindle lathe make INDEX type ER 25Mash. -No: 25751408max. workpiece passage Drm.:25 mmxa0xa0xa06-edge: 21 mmxa0xa0xa0Square: 16 mmmax. workpiece feed p. Circuit: 70 mmmax. thread diameter: M 16 / M 14Speed range: 14 - 5750 rpm.Number of automatically switchable speeds: 4Number of overdrive speeds: 26Number of slow speeds: 234Turret diameter: 120 mmTool holder cone: 3/4 Turret processing: 60 mmDistance collet - Turret: 60 - 150 mmFeed rate infinitely variable: 16 - 2800 mmFeed rate continuously variable: 40 - 7000 mm / minRapid forward / backward: 10/25 m / minSwitching time: 0.75 sCross slide travel: 44 mmLongitudinal adjustment of the upper slide: 20 mmContinuous feed of the cross slide: 5 - 1000 mm / minDriving power: 4 kWDimensions L x W x H: 1900 x 1020 x 1650 mmWeight approx: 1650 kgWith- 8-fold revolver- 2 vertical parting carriages- 2 horizontal cut-off slidesused, in very ...

Cam-type single-spindle turning machine make MAS Kovosvit type A 50 CA.Make -No: 007 built in 1991Max. Drm. of bar stock Infeed / Outfeed: 52/60 mmMax. Length of the bar material: 3000 mmMax. Displacement of the bar stock at feed: 90 mmSpeed range: 15 - 2244 rpmNumber of supporters: 4Max. Working stroke height of the supports: 45 mmNumber of turret settings: 6/8Max. Working stroke - height of the turret: 85 mmMax. Threaded by taps Thread:in steel: 24 x 1.5 mmin brass: 36 x 1.5 mmWeight: 2490 kgConnected load: 10 kVAExternal dimensions L x W x H: 2150 x 1125 x 1970 mmWeight: 2530 kgused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Turret lathe make MANURHIN type Dekomat 50Mash. -No: 3005-157Spindle bore: 50 mmgr. rod cover: 42 mmgr. Diameter of the chuck: 160 mmGr. working diameter: 120 mmSpindle drive pol. Engine: 4/8 hpNumber of programmed speeds: 4Number of speed groups: 5Speed range: 75 - 3200 rpm.Number of turret positions: 8long stroke: 150 mmLarge planing stroke: 49.7 mmgr. Radius difference when copying: 17 mmNumber of longitudinal feeds per cycle: 3 (+ 4 )Number of feedrates per cycle: 2 (+ 1 )Feed range longitudinal: 0-425 mm / minFeed range flat: 0-150 mm / minRapid traverse: 7 mm / minExternal dimensions without bar feed: 2300 x 1200 x 1500 mmWeight: 2000 kgWith- separate control cabinet- Connector panel controlusedPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you  ...

Program controlled lathe type TRAUB type TF 60/140Machine -No: 194 Year 1976Max. Bar passage: 60 mmMax. Chuck: 120 mmMax. Clamping diameter: 130 mmSwinging diameter: 190 mm21 spindle speeds: 21 - 2000 rpm.switchable speeds: 4 right 2 leftSled trails: 125 mm along: 70 mm acrossinstalled power: 14 kWWith- Copying device- sweeping device- hydr. tensioning device- bar feed- 2 vertical slides- 2 horizontal slides- collet set- Three-jaw lathe chuckused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

AUTOMATIC SPINNING LATHE DENN RPE-290 Denn Mod.RPE-290 Automatic Spinning Lathe- Spindle Speeds 615/1060/1825 RPM. More information on request.

Face plate diameter: 4200mm Swing diameter: 4950mm Turning height: 3000mm Ram: 300mm x 300mm (Z-Stroke: 2100mm) Workpiece weight: max. 30t Accessories: PickUp station Control 840D Sl Machine was completely overhauled, machined and rebuilt.

CNC CONTROL: MSD 501 II, FANUC FEATURES: DIAMETER ADMITTED ON THE BED, MM 680 MAXIMUM TURNING DIAMETER 440 MM N1 MAXIMUM TREATMENT DIAMETER N2 322 MM MAXIMUM TURNING LENGTH, MM 471 THE STANDARD MACHINING DIAMETER MM170 MAIN SPINDLE: STEP PANEL 45 MM COUNTER SPINDLE: HOLE PITCH LINE 43 MM TURRET 1: POSITION N12 ALL MOTORIZED TOWER 2: POSITION N12 ALL MOTORIZED

Machine weight: 39,000 kg Faceplate diameter 2000 mm number of supports: 2 pcs. Dimensions : Height 6280 mm width 6600 mm length 4800 mm Extras: Right support with turret head, left and side - sliders. Digital indication of NS 114. Technical condition at the time of sale: Defective rotary amplifier main drive-replacement is required. Require replacement of cables and wires external piping:-machine control cabinets. Repair and adjustment of electrical parts. Not operated since 1994 The maximum dimensions of a workpiece Height 1300 mm Diameter of 2000 mm Weight 15 000 kg

Peak height 200 mm Tip width 1500 mm Turning- over slide 235 mm over bed 425 mm via kröpfung 470 mm Speed Continuous 45 - 2240 rpm Spindle bore 45 mm • the Reitstockpinole 55 mm Morse cone of the spindle and tailstock MK 4

Largest workpiece height: 630 mm Largest workpiece diameter: 800 mm Largest workpiece weight: 2000 kg Engine power: 40 kW Dimensions: 2600x2500x3700 mm Machine Weight: 10000 Kg Electrical table voltage Electrical rotation of the knife head Shaped copy via template Two-axis measurement Ball screw Suitable for CNC conversion Accessories: Clamping pressure gauges Tools

Machine

Machine Details Stock-No. 1105-03620 Type of machine CNC Lathe Make SPINNER Type TC 32 Year of manufacture 1999 Type of control CNC Storage location HAGUENAU Country of origin Germany Delivery time Immediate Freight basis ex Site Technical details turning diameter 150 mm turning length 300 mm control SIEMENS 810 D swing diameter 300 mm swing diameter over face slide 150 mm x-axis 400 mm z-axis 285 mm spindle passage 32 mm spindle motor 7.5 kW spindle turning speed - stepless 8000 rpm c-axis 0.001° Turret positions 12-speed VDI 25 work piece power 1.2 kW toolpiece turning speed range 6000 rpm weight of the machine approx. 1.8 t dimensions of the machine ca. 2 X 1 X 1.6 m Additional information CNC CONTROL SIEMENS 810 D

- Digital display - Accessories available. Peak height 200 mm Peak width 800 mm Turning- over slide 235 mm over bed 425 mm Speed 36 - 1780 rpm Recording Camlock 6 Spindle bore 45 mm Flat and longitudinal feed 0.05 - 2.8 mm/U • the Reitstockpinole 55 mm Morse cone of the spindle and tailstock MK 4 Spindle motor 8 hp

Machine is in good condition. Machine has a semi-spindle and it does not have a chip-federal.

Table diameter 1450mm Max working diameter 1600mm Max height under crosstravel 1000mm Nr. 02 RAM Visualization by DRO 4 axes Good working conditions Machine weight18 ton

Vertical lathe KOLOMNA 1540 T CONVENTIONAL MACHINE READY TO INSTALL Spindle diameter 4.000 mm Working diameter 4.140 mm Max working height 2.060 mm Ram travel 1.250 mm Weight over spindle 100 ton Motor power spindle 100 kW Boring/milling unit included Nr.02 RAM with visualization by DRO Excellent conditions, mechanical really like a new.

DATA ABOUT THE MACHINE Machine type: CNC lathe Manufacturer: Gildemeister Type: CTX400 Year of construction: 1993 Condition: used Location Warstein , Germany Reference M-GIL-0922 DESCRIPTION We offer you a used CNC lathe from the manufacturer Gildemeister NEF. Technical data (without guarantee) Circulation diameter over bed: 500 mm Turning length: 600 mm Number of spindle rotations: 20 - 5000 rpm Number of tools: 12 Spindle bore: 72 mm Tailstock pinole diameter: 80 mm Tailstock pinole stroke: 100 mm Total power requirement: 45KVA Space requirement approx.: 4.5 x 2.0 x 1.8 m Drive for driven tool (tool turret) without function Machine is in continuous production. Availability: From mid-Oct. 2022 Our offer is aimed at commercial persons who are covered within the meaning of the Trade Code according to §14 GewO. The offer is subject to change, subj ...

Table diameter 2.000 mm Working diameter 2.000 mm Machine under retrofit/rebuilding to install CNC Mechanical ready, totally rebuilt.

Machine Details Warehouse number 1105-03703 Machine type CNC lathe - inclined bed machine Make SOMAB Type TRANSMAB 400 Year of construction 2002 Conventional control type Control NUM 1060 T Storage location FRANCE Country of origin France Delivery time immediately Freight base EX WAREHOUSE Technical details Turning diameter 500 mm Turning length 650 mm Control NUM 1060 T Turning diameter above the face sled 240 mm Turning diameter via transverse guide 320 mm Main drive motor 18/24 kW Spindle speeds 3600 rpm Spindle passage 73 mm Chuck diameter 210 mm Tailstock cone MK 4 Total power requirement 30 kW Machine weight approx. 4 t Space requirement approx. 3.60 X 2 X 2 m Information Machine in inclined bed design with NUM 1060 CONTROL HYDRAULICK CHUK PARTS FAENGER SPAENEFOEDERER 12x revolver VDI 30

CNC fine lathe Make: PetrolGer Type: TNL Control: Siemens 810T Built: 1991 Equipment and accessories: - Swivel loader system - Small conveyor belt - Charging-unloading gripper - Chip conveyors - Foot lever for clamping and relaxing the collet

MANURHIN KMX SWING 720 CNC lathe was built in 2004 in France. The automatic lathe is used for precision machining of workpieces with a maximum length of 2500 mm and a diameter of 20 mm, in ten axes. The high quality of the workmanship, high turning precision and reliability of the turning centre, will satisfy even the most demanding customers. The KMX SWING 720 swiss type lathe guarantees the possibility of performing a wide range of metal machining, thanks to the use of a main spindle together with a sub spindle rotating at a maximum speed of 10000 rpm. The machining tools are stored in a magazine with a capacity of up to 14 pieces and they are changed in a very short time. The lathe is equipped with a Fanuc Series 160i-T CNC controller for full control of the machine and a Hydrobar Express 226 LNS bar feeder. The total weight of the machine is 4300 kg. Technical parameters of  ...

Inv. Num. : 6238 Type: HIT-250 MS Producer: HYUNDAI Created: 2004 Parameters: Control system: Siemens Sinumerik 840D turning length: 650 mm turning diameter: 390 mm Maximum turning diameter over bed: 590 mm Maximum spindle speed: 3600 1/min Maximum main spindle power: 15 kW Spindle passage: 80 mm Number of all tools: 12 pieces Number of driven tools in the turret head: 12 pieces Chuck diameter: 250 mm Axis X: 265 mm Axis Z: 660 mm Clamping diameter (counter spindle): 160 mm Spindle passage (counter spindle): 50 mm speed (counter spindle): 4500 1/min Length: 3692 mm Width: 1850 mm Height: 1850 mm Weight: 6450 kg Equipment: C-axis Technical documentation Conveyor Driven tools 2x 3-jaw chuck Cooling Complete coverage of the work area Oil mist separators Housing for clamping rotary knives and cases (8 pcs.)

Machine Details Stock number 1105-03732 Machine type CNC lathe - inclined bed machine Brand BIGLIA Type B 111 - S Year of construction 1995 Control type CNC Control Fanuc 0-T Storage location FRANCE Country of origin Taiwan Delivery time by arrangement Freight base from location Technical details Turning diameter 180 mm Turning length 280 mm Control Fanuc 0-T Rod passage: 42 mm Speed range - spindle 6000 rpm Feed range - turret / infinitely variable 1 - 12000 mm/min Rapid traverses 20 / 24 m/min Number of tool turrets: 1 piece Tool turret - places: 12 stations Tool holder direct pick-up Tailstock MK 3 Total power requirement 7.5 kW Machine weight ca. 3,2 t Space requirement approx. 2800x1700x1700 mm Accessories 3 - Baking - Lining Complete machine documentation Conveyor Parts catcher Collet device Electronic handwheel Coolant device Tool - Sett ...

Machine Details Stock number 1105-03735 Machine type CNC lathe Brand MAZAK Type QT 20 N Year of construction 1995 Control type CNC Control Mazatrol T PLUS Storage location FRANCE Country of origin Japan Delivery time immediately Freight base from site Technical details Turning diameter 440 mm Turning length 451 mm Control Mazatrol T PLUS Turning diameter via bed carriage 300 Tailstock holder MK 4 Quill stroke 130 mm Tailstock displacement 500 mm x-axis 180 mm z-axis 510 mm Spindle bore 62 mm Speed range 12-4500 rpm Total power requirement 40 KVA Machine weight ca. 4,2 t Information WITH MAZATROL T PLUS Good Macschine All prices plus VAT. VAT.. Changes and errors in the technical details and information reserved.

MACHINE IS IN GOOD WORKING CONDITION Machine need center horse and support for the clamp cutting tools. Bj0ie7dcoa Machine Has ben used in Switzerland, after thay realize they need that both suports, they took it off and use on other lathe.

:::SPECIFICATIONS::: CNC Model: Okuma OSP CNC version: U100 - L Spindle nose: ASA 6 Spindle power: 22Kw Main spindle revolutions: 5000 Turning diameter: 630mm Bar clearance: 51mm Turning length: 1170mm Number of tools: 44 Tool connection: HSK 63 Spindle power: 7,7Kw Number of spindle revolutions: 6000 X Axis Stroke: 475mm Y axis stroke: + - 80mm Z Axis Stroke: 1155mm Swivel B-axis travel: 0.001degree Rapid feeds linear axes X Y Z: 40m/min High cooling pressure: yes Pressure value: 120bar System with external tank with filter: yes Number of Tool Turrets: 1 Number of tool places before turret: 12 First turret tool attachment type: VDI Counter-spindle: yes Number of counter-spindle revolutions: 6000 Counterspindle power: 22Kw Bar clearance: 32mm Z stroke counterspindle : 1180mm Model and brand bar magazin ...

Type: LT200-MY Twin Star Year of construction: 12/2006 Commissioning: 2007 Control: OSP – P200L Delivery time: ex stock The lathe is in very good general condition. Due to the basic and additional equipment, this used machine is versatile. With the automatic bar feeder, the double turret equipment, the additional Y-axis and the parts catcher, the machine produces your workpieces completely independently. From start to finish. Due to the equipment with main and counter spindle, production can be economically effective and fast. Machinery Collet chuck SMW on both sides Main and counter spindle Y-axis Conveyor Bar loading magazine Turbo 5-55 Parts catcher - B-turret with swivel ejection to the collection box (at the door). Onward transport by internal parts conveyor belt. Technical details Swing diameter: mm 400 turning diameter: mm 210 turning length: mm 960 2 tool ...

Machine Details Stock number 1105-03764 Machine type CNC lathe Brand HURCO Type TM8 Year of construction 2012 Control type CNC Storage location HAGUENAU Country of origin Delivery time at short notice - by arrangement. Freight base delivery from location. Technical details Turning diameter 305 mm Turning length 477 mm Planweg. (x-axis) 203 mm Longitudinal travel 508 mm Spindle bore 52 mm Speed 4800 rpm Tool turret 12 Rapid traverse 19/24 m/min Total power requirement 11 kW Machine weight ca. 3800 kg Information Equipment: - Winmax CNC control - 3-jaw chuck - 12-fold revolver - Tool measurement -Tailstock -Conveyor - Coolant device

CNC Lathe with indexing chuck ( Autoblock) SPINNER TC400 52

CNC control: FANUC 0i-TF+ with 15" LCD color display and Manual Guide i -12-fold tool turret with BMT45 holders, 24-fold indexing -Coolant device with 10 bar delivery pressure incl. coolant gun -WTO Holder Package -Oil skimmer with endless belt for extraneous oil separation -Warning light with 3 colors -Workspace lighting -Bar feeder interface for connecting loading magazines -Chip conveyor, ejection right -Part ejector on counter spindle incl. cooling by the spindle -Chuck blow-out device on the counter spindle -Parts catcher with parts conveyor belt inside -Automatic surveying arm -Transformer -CE conformity -English machine manuals -Main spindle: 3-jaw power chuck Ø210 mm (8") for spindle head standard: A2-6; Make: SAMCHULLY incl. 1 set of soft and 1 set of hard jaws -Counter spindle: 3-jaw power chuck Ø135 mm (5") for spindle head standard: Flat-110; Make: SAMCHU ...

- Siemens Sinumerik control - Chip conveyors - Coolant system - Built in 2002 Technical data - Circulation diameter: 235 mm Sledge path: - Z-axis (vertical): 250 mm - X-axis (horizontal): 450 mm + 370 mm - Workpiece height: 100 mm - • in the front bearing: 90 mm - Spindle head with short cone DIN 55026: A5 - Hollow shaft motor with oil circulation cooling: integrated into the spindle box - Rated power 100% ED: 29.3 kW - Nominal torque 100% ED: 200 Nm - Rated speed: 1400 rpm - Maximum speed: 6500 rpm - Travel speed Z-axis: max. 30 m/min - Travel speed X-axis: max. 60 m/min

Machine Details Stock-No. 1105-03781 Type of machine CNC Lathe - Inclined Bed Type Make MAZAK Type sqt 30 Year of manufacture 1998 Type of control CNC Storage location FRANCE Country of origin Japan Delivery time on request Freight basis ex location Technical details turning diameter 560 mm turning length 10000 mm control MAZATROL T PLUS greates pass round over bed 560 mm swing diameter over slide rest 400 mm spindle cone A 2-8 Spindle bore 77 mm Spindle motor 22 kW turning speeds 3500 rpm total power requirement 35 kW weight of the machine approx. 6 t Additional information WITH turret Swarf Conveyor Tool Eye Parts Catcher

Machine Details Stock-No. 1105-03782 Type of machine CNC Lathe - Inclined Bed Type Make BIGLIA Type B 121 S CNC Year of manufacture 1989 Type of control CNC Storage location FRANCE Country of origin other Delivery time at once Freight basis free loaded Technical details turning diameter 520 mm turning length 420 mm control fanuc ot Spindle Bore: 45 mm turning speed range - spindle 4900 rpm Rapid traverse 20/12 m/min tool taper VDI 30 tail stock MK 4 total power requirement 20 kW weight of the machine approx. 3.5 t dimensions of the machine approx. 2900x1800x1800 mm Additional information WITH FANUC OT CONTROL Tailstock 3 Jaw Chuck Chuck Chip Convoyer

CNC Lathe Gildemeister CTX 200 Series 2 Immediately free from location: CNC Lathe Gildemeister Type CTX 200 Series 2 Built in 2001 Operating hours 39,000 CNC Control Heidenhain 4290 TP Turning diameter 210 mm Turning length 305 mm Reiststock revolver 12 driven tools Conveyor Bar loading magazine Max travel plan 160 mm Max travel length 350 mm Spindle speeds up to 5000 rpm 2 simultaneous axes with C axis 1 controlled spindle 12 driven tools Collet pliers with hydr. Hollow clamping device up to 43 mm Workpiece pick-up device up to 56 mm very many tools

Bridgeport EZ Path S Used machine (very good) Control type Cnc Built 2001 Hours K.a. Price 12,500 € net plus VAT Dimensions 3100x1850x1500 Weight 2500 kg Location Haiger Description Universal CNC cycle deer of the brand Bridgeport suitable for tooling, fixture construction, training as well as mold making • Circulation diameter: 430mm • Control: Fanuc 20T Technical data • Circulation diameter 430mm • Peak width 1000mm • Control Siemens Fanuc 20 T • Reitstock MK 4 • Multifix tool station • Speed 1-4000rpm • Connection 380V - 7.5 KW

Lathe

Lathe

Lathe

Machine Details Stock number 1105-03811 Machine type CNC lathe - inclined bed machine Brand GILDEMEISTER Type CTX 410 Year of construction 2004 Control type CNC Control HEIDENHAIN TURN PLUS Storage location FRANCE Country of origin Germany Delivery time available at short notice Freight Base EX WORK Technical details Turning diameter 320 mm Turning length 600 mm Turning diameter 320 mm Travel - x 260 mm Travel - z 635 mm Orbital diameter 680 mm Orbital diameter via slide 365 mm Spindle bore diameter 87 mm Turret head (x-fold) 12 Main spindle speed heidenhain turn plus 1/min Rapid traverse X + Z - axles 24/30 m/min Drive power - spindle motor 21 kW Control HEIDENHAIN TURN PLUS Power supply 40 kVA Information control HEIDENHAIN TURN PLUS 2 AXIS MACHINE 12-fold turret VDI 30 Spaneforderer

CNC control: FANUC 0i-TF+ with 10.4"/15" LCD color display and Manual Guide i -12-fold tool turret with BMT65 mounts -Coolant device with 10 bar delivery pressure incl. coolant gun -WTO Holder Package -Oil skimmer with endless belt for extraneous oil separation -Warning light with 3 colors -Workspace lighting -Bar feeder interface for connecting loading magazines -Chip conveyor, ejection right -Part ejector on counter spindle incl. cooling by the spindle -Chuck blow-out device on the main spindle -Parts catcher with collection box -Automatic surveying arm -Transformer -CE conformity -English machine manuals -3-jaw power chuck Ø210 mm (8") for spindle head standard: A2-6; Make: SAMCHULLY incl. 1 set of soft and 1 set of hard jaws -Counter spindle 8": 3-jaw power chuck Ø170 mm (6") for spindle head standard: A2-5; Make: SAMCHULLY, incl. 1 set of soft and 1 set of hard  ...

Universal CNC lathe BOEHRINGER NG 200 Manufacturer: BOEHRINGER Type [ type]: NG200 CNC double Control unit: Siemens 840D Year of construction[construction year]: 10/2001 Rotating diameter: 290 mm Turning length: 850 mm Control: SIEMENS 840 D Orbital diameter over bed: 600 mm Revolver 1 Revolver 2 Counter spindle Counter headstock Tailstock C-axis Powered tools Automatic machine doors – newly retrofitted Z-axis resolution: 40nm (2nm interpolated) Travel in Z: 740mm Rapid traverse speed in Z: 25 m/min Centering tip SK 30 X-axis resolution: 125nm (8nm interpolated) Travel in Z: 220mm Rapid traverse speed in Z: 25 m/min Distance between main and counter spindle: 1034mm Drive power: 30-72 kW Torque: 662 Nm Speed range max.: 4500 rpm Spindle head: Size 6/8 DIN 55026 Spindle diameter in the front. Bearing [spindle]: 120 mm Chuck diameter: 200-315mm Spindl ...