134,878 used machines on RESALE, but how to find them? Machine Search
; Power [PS]: 170; Gross weight [kg]: 8250; Engine: Battery System: LIFePO4; Accessories: Battery, Stahldach
Fuse protection: 100A, control voltage: 220V, operating voltage: 380V, connected load: 30,4kW, weight: 14,4t, with four-jaw chuck (diameter: 900mm), tailstock, quill, three steady rests and control system. An on-site inspection is possible.
Clamping force: 500kN, tie-bar spacing: 320x320mm, cylinder diameter: D30, control: Arburg SLOGICA, automatic operating hours: 63.147h, pump operating hours: 65.755h, semi-automatic operating hours: 14h, cycles: 13.943.435. An on-site inspection is possible.
capacity 90 degrees: round: 500 mm capacity 90 degrees: square: 420 mm : 600x400 saw band length: 5320x34x1,1 mm band speed: 15 - 100 m/min table height: 805 mm total power requirement: 3,0 kW weight of the machine ca.: 1,45 t dimensions of the machine ca.: 1,72 x 2,5 x 2,5 m Double miter band saw, hydraulic semi-automatic, DGS 500/600 HA-I • miter left + right 60° • Frequency-controlled saw drive • 34 mm saw band height • Wear-free material support turntable, ball-bearing • To position the saw blade guides using a very wide linear guide • Strong, robust gearbox • Large chipboards • 2 integrated support rollers left and right • Removable chip tray (disinfection) • Free-standing control panel, safe and ergonomic • Storage space for tapes, consumables • Hydraulic cutting pressure control valve • Material height sensor (automatic cut start detection) • Preload s ...
Year of manufacture 1997 Foil Packing Machine Angle welding machine Manual installation Shrink tunnel Mobile substructure Price on request. We deliver and install worldwide!
Specifications: Max. sheet width: 2500 mm Max. sheet thickness: 8 mm Weight, approx.: 6400 kg
Diesel Fuel Tank 4.500 Liter, 4.500 Liter Tank, UL142 Certified
Setting total time Frequency speed control Automatic unloading Vacuum 0-95% Vacuum system filter Volume: 500 liters Machine dimensions in cm: Length: 178 Width: 102 Height: 155 Electric power: 3 kW
Setting total time Frequency speed control Automatic unloading Vacuum 0-95% Vacuum system filter Volume: 1000 liters Machine dimensions in cm: Length: 214 Width: 133 Height: 190 Electric power: 5 kW
Key data: 45 °, 3500 mm, 1350 mm
Basic Cutting length 3500 mm Cast iron sawing unit type Z5 Max. saw blade (not incl.) 500 mm, max. 350 mm with scoring saw blade Scoring unit 120 x 20 mm Cutting height 90°: 175 mm, 45°: 120 mm 3 speeds: 3000/4000/5000 t/min 8D9Kjux2Mt Cutting width between saw blade and Z4 rip fence 1350 mm Z5 Cross Table (1505x760 mm) with Telescopic with Z5 Mitre Stop with 2 Folding Stops Comfort Pack on Cross Table with Extendable Workpiece Roll Frame table with extendable support and degree grid index system with length compensation Motorized height adjustment and inclined position of the saw blade incl. special accessories: Motor 9.2 kW Start/stop in the sliding table
Rexroth Type : 4281. 14 . 09903 . 97 3622-505045314 Kind. . No. 1190103 Stiebel Gear Type :4281.14.09903.97 Type.nr : 3622-505045314 Art.no : 1190103 From stock
ALLSHENG Nano-500 UV-Vis Fluorometer / Spectrophotometer (Micro Volume and Cuvette) New equipment in its original packaging Year of Manufacture: 2023 Model: Nano-500B Light Source: Blue LED Excitation wavelength: 460 ± 20 nm Emission wavelength: 525–570 nm (45 nm) Minimum sample volume: 0.5 μL – 2 μL (2 μL recommended) Optical path length: 0.05 mm, 0.2 mm or 1 mm Light Source / Lifespan: Xenon Flash Lamp Detector type: 2048-element silicon linear CCD array Wavelength Range: 200 – 800 nm UV-Vis Wavelength accuracy: ±1 nm Spectral resolution: ≤3 nm (FWHM at Hg 253.7 nm) Absorbance accuracy: 0.003 Abs (1 mm light path) Absorbance accuracy: ±1% (7.332 Abs, at 260 nm) Absorbance range: 0.04 – 300 (at 260 nm, 10 mm equivalent) Detectable concentration range: 2 ng/μL – 15,000 ng/μL double-stranded DNA (dsDNA) Detection time: < 6 seconds OD600: Absorb ...
Key data: 750 mm, 750 mm, 725 mm
GENERAL Project No.: 905674 Quantity: 1 pcs. Manufacturer: HECKERT (STARRAG) Type: HEC 500 D Control: Siemens 840 D solutionline Year of Make: 2011 Condition: Used machine Layers approx.: 2-3 layers DESCRIPTION MILL Travel in X 750 mm Travel in Y 750 mm Travel in Z 725 mm Max. rapid traverse speed in X/Y/Z 100/100/100 m/min Max. acceleration in X/Y/Z 11/14/11 m/s2 Tool holder HSK 63 Max. speed milling spindle 15000 1/min Max. power at ED 10-40/100% 31/– kW Max. torque at ED 10-40/100% 200/– Nm Spindle diameter in the front bearing 75 mm 1 pc. horizontally arranged milling spindle/s Torque support for multi-spindle drill heads Tool magazine 60 stations Max. tool diameter 160 mm Max. tool length 400 mm Max. tool weight 10 kg Chip to chip time 2.7 s Rotary pallet changer 2-fold Pallet size 500×630 mm Max. workpiece weight per pallet 600 kg Rotary ...
This 3-axis MORI SEIKI DURA VERTICAL 5060 was manufactured in 2007. It features a travel distance of 600 mm in the X-axis, 530 mm in the Y-axis, and 510 mm in the Z-axis. The machine includes a table size of 900 x 600 mm and a maximum table load of 500 kg. If you are looking to get high-quality machining capabilities, consider the MORI SEIKI DURA VERTICAL 5060 vertical machining centre we have for sale. Contact us for further details.
Key data: 300 mm, 500 t, 350 mm
Millutensil SLMD 500. Double decoiler / double rewinder. Capacity load: 500 kg x 2. Inner diameter min 350 mm max. 600 mm. Strip width up to 300 mm. Outer diameter max. 1600 mm. High frequency inverter Danfoss. Sensor for loop control. Dimension 2000 mm x 2000 mm height 1800 mm. Made in Italy.
This 4-axis Mazak HCN-5000 was manufactured in 2024. It features an X-axis travel of 730 mm, Y-axis travel of 730 mm, and Z-axis travel of 800 mm. The machine has a maximum workpiece weight of 700 kg and a spindle speed of 18,000 RPM. If you are looking to get high-quality machining capabilities, consider the Mazak HCN-5000 horizontal machining centre we have for sale. Contact us for further details.
The Klingelnberg PSR 500 U worm gear testing machine was designed as a universal machine for the flexible testing of worm gears and is used by manufacturers of gear and gear technologies for the process of single-flank rolling testing for worm gear sets EFWP. Technical data Max. worm wheel diameter: 500 mm Max. spindle length: 500 mm Max. spindle diameter: 200 mm Center distance: 0 ... 400 mm Max. measuring speed: 60 rpm Braking torque: 2.5 Nm Max. worm wheel weight: 150 kg Max. spindle weight: 50 kg Table diameter: 300 mm Machine weight: 800 kg Dimensions: 1500 x 1500 x 1600 mm The following parameters can be measured here: • Single-flank deviations Fi', fi', fl', fk' • Crossing, concentricity, roundness (option) • Carrying pattern with digital camera • Pitch deviation • FFT analysis, spectrum Picture shows the machine in its current ACTUAL condit ...
Key data: 5000 mm, 275 mm, 310 mm
Urban AP 5000 F - Travelling column milling machine - Heidenhain track control TNC 410 M, control panel can be moved over the entire processing length - Robust basic construction as a welded frame construction - Ball rail guides on all axes - Milling spindle unit: 80 - 6000 rpm, tool holder SK30 - X-axis with rack and pinion drive (30 m/min) - Y/Z axis with ball screw (20 m/min) - 2 chip drawers - Swivelling clamping device for 4700 mm workpiece length - 10 Pneumatic workpiece clamps - Manually operated central lubrication - Moving disc tool changer for 8 tools - Micro-Spray - Cooling emulsion pump - Machine light - Safety bumper - Machine guard pneumatically vertical opening - Year of construction 2005 - Control on: 26910h - Program run: 9185h - Spindle on: 6557h Defects: - Air hoses of the tensioners have to be partially replaced - Contact cables of the cylin ...
1 Farben Offsetdruckmaschine - 1 Color Sheet-Fed Offset Press HAMADA 500 CDA Serial-No. HR-6462 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test
Pressure: 15 bar Motor: 11 kW Free air delivery: 1,319 m³/min Measurement (WxHxD): 2125 x 1730 x 820 Weight: 550 kg Compressed air connection: 1 1/4
Pressure: 10 bar Motor: 5,5 kW Free air delivery: 0,815 m³/min Measurement (WxHxD): 1890 x 1520 x 854 Weight: 437 kg Compressed air connection: 1/2
Halb-automatische Winkeleinschweißmaschine - Semi-Automatic Foil sealing machine Kallfass KC5050/400 Year 1983 - Serial-No. V 6.83.1891 Mobile on mobile frame After sealing - automatic transport into tunnel Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test
Load capacity: 1600kg, lift height: 3300mm, engine: Ford, drive: LPG. UVV inspection sticker 2026 available. The hydraulic system was serviced in 2026. Documentation available. Inspection by appointment possible.
Punching force: 500 kN For example, punches a 20 mm hole in 18 mm steel Stroke release via foot switch Range of tools is included in the price
Stapelauslage / Stacking Delivery Palamides Alpha 700 Plus Baujahr / Year 2011 - Serial-No. 2502 Minimalformat / Size minimum 120mm x 90mm Maxmimalformat / Size max. 330mm x 510mm Stapelhöhe / Stack height 10 - 160mm Geschwindigkeit / Speed 15 - 200m7min Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test
Buchrückenrundemaschine - Book Back Rounding Machine Tränklein BRM 500 Serial-No. 1586/74/1 Working width max. 540mm Thickness of books 0 - 100mm Output 400 - 600 Blocks/Stunde Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test
Antike Falzmaschine - Antique Machine folding machine Brehmer 1/504 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test
This 3-axis DOOSAN DNM 500 was manufactured in 2011. It features a table size of 1200 x 540 mm and impressive travels of 1020 mm in the X-axis, 540 mm in the Y-axis, and 510 mm in the Z-axis. The machine is equipped with a 30-position automatic tool changer and a spindle speed of 12,000 rpm. If you are looking to get high-quality machining capabilities, consider the DOOSAN DNM 500 vertical machining centre we have for sale. Contact us for further details.
Carpet carousel 5000 mm Carousel rack for carpet and flooring rolls Robust and fully functional carpet paternoster (carousel shelf). The system is ideal for space-saving, vertical storage and display of carpets, PVC rolls or other heavy roller goods. Length approx. 5000 mm Capacity: approx. 12–16 support rods / roller places The carpet and floor coverings for the respective carousel rack can be purchased extra for €1000 net. Item location: Frankfurt am Main Period: The collection must take place at the end of September to the beginning of October. Option 1 (self-collection): Dismantling and removal are carried out independently by the buyer. Option 2 (all-round carefree package): We are happy to offer you professional dismantling by us, including delivery throughout Germany, for a flat rate of €1,000 net (plus VAT). "Everything from a singl ...
turning diameter over bed: 400 mm turning diameter over slide rest: - mm turning length: 1000 mm total power requirement: 9 kW weight of the machine ca.: 2 t dimensions of the machine ca.: 2,511,6 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 990 mm, 1730 , 1200
Machine type: EVK 500 Manufacturer: ERBA Heating element kW: 4.0 Total volume: 500 lt. Description: With the ERBA Granulate Dryer EVK 500, workpieces can be easily separated from the granulate with the integrated screening device. It has excellent drying ability, a direct heating system and digital temperature control. The working tank is completely sprayed with polyurethane on the inside. The EVK 350 can be linked to other machines. The price quoted is net plus the currently valid statutory sales tax and plus freight costs. The pictures can show the system including accessories, which are optionally available and associated with additional costs. The price quoted refers to the basic machine. If you are interested, we look forward to hearing from you. We will be happy to advise you without obligation. The European Commission provides a platform for out-of-court online ...
Mains connection: 3P + PE, operating voltage: 400V, frequency: 50/60Hz, control voltage: 24V DC, connected load: 3.5kVA, rated current: 4.8A, total current: 4.8A, upstream fuse: 3×16A. The machine is in perfect condition. An on-site inspection is possible.
4-Spindle Paper Drilling Machine Ideal 504
Specifications: Digital 3-axis digital display HEIDENHEIN TNC 134 X-axis travel 500 mm Y-axis travel 350 mm Z-axis travel 380 mm Tool holder SK 40 vertical milling head with hydr. Tool Clamping DIN 2080 Ring Groove Table type Banquet table Table clamping surface 800 x 360 mm T-slot size 14 mm Weight 1,600 kg Dimensions 1500 x 2000 x 1900 mm Accessories -Central lubrication - Coolant device -Operating instructions
This 3-axis MORI SEIKI NV 5000 alpha1 was manufactured in 2008. It features an X-axis travel of 1020 mm, Y-axis travel of 510 mm, and Z-axis travel of 510 mm. The machine has a weight of 7300 kg and includes a central spindle cooling unit, along with a Blum laser tool measurement system. If you are looking to get high-quality machining capabilities, consider the MORI SEIKI NV 5000 alpha1 vertical machining centre we have for sale. Contact us for further details.
Locker changing room 1800 x 1200 x 500 RA2221 Manufacturer: unknown width: 1200 mm Height: 1800 mm depth: 500 mm different versions available 3 x 2, 2 x 2, 3 x 4 and 2 x 4 (horizontal x vertical) lockers benches also available Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics
; Gross weight [kg]: 5230; Engine: Perkins 2506A-E15TAG1; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 775
Drilling method ELB Full drilling 4-33mm Drilling depth max 737mm Spindle antrib 7,5 kw Spindle speed 550-6400rpm Working feed 35-320mm/min Rapid traverse 3500mm/min Coolant High Pressure Pump, Paper Filter, Chip Conveyor, Magnetic Separator Connection 20 KW Dimensions 4100 x 1650 x 1850mm Weight 3500 KG
Transnorm belt curve conveyor left GKF 90°-800-600-IR400 - Exhibit RA2318 Technical data: Frame width (NB): 800 mm Frame width with Bearing cover and motor: 1000 mm belt width (GuB): 600 mm height (BH): 200 mm height with motor (MH): 350 mm Inner radius (IR): 400 mm Conveying angle: 90° degrees Conveying speed (v m/s): 0,38-1,14 m/s Drive: Nord gear Motor with Frequency converter for stepples speed controll Electrical data: 50Hz V380-500, kW 0,37 / S1 Year of construction: 2020 Incl. 2 supports, current height 810mm Optionally available: Support, if deviating from the currently installed Sideguides Prices net plus VAT from central warehouse Dr. Sonntag GmbH & Co KG, Gattingerstreet 11 B & C, 97076 Würzburg Features: Construction year: 2020 condition: Ausstellungsstück Nominal / inner radius in mm: 400 Nominal / outside width in mm: 800 Belt width in mm: 600 angle: 90° Driven: YES R ...
Transnorm Rising falling Incline belt conveyor with leading belt GF 4600+3300-600-600 RA2202 Technical data: Conveyor length (NL): 7900 mm ( 4600 mm riser segment + 3300 mm forerun) frame width (NB): 600 mm, 700 mm with motor belt width (GuB): 500 mm Overall height (BH): 80 mm, 430 mm with motor Angle: freely adjustable between 0 and 15° Supporting feet: optionally available Conveying speed (v m/s): contact us Drive: SEW gear motor, Electrical data: 50Hz V380-500, kW 0,75 S1 Drive drum: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Side guide on one side and on both sides Frequency converter for stepless speed change Adjust length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany Features: Construction year: 1998 condition: good (used) Conveying length in mm: 7900 ( 4600 + 3300 ) Nominal / outside wid ...
CNC punching machine manufactured in 1995. This TRUMPF Trumatic 500 features a maximum punching force of 220 kN, accommodating workpieces up to 150 kg. It offers a working range of 2500 mm along the X-axis and 1250 mm along the Y-axis, allowing for efficient processing of various sheet sizes. If you are looking to get high-quality punching capabilities, consider the TRUMPF Trumatic 500 machine we have for sale. Contact us for further details regarding this machine.
maximum number of results exceeded
please refine your search
