134,602 used machines on RESALE, but how to find them? Machine Search
Machine Type: Center Grinding Machine Manufacturer: Henninger Model: ZS 200 Year: Not specified - Max Workpiece Length: up to 2000 mm - Workpiece Diameter: 285 - 325 mm - Center Diameter: 2 - 110 mm - Bore Taper: 50 - 120 mm - Center Height: 165 mm - Wheel Diameter: 10 - 60 mm - Grinding Wheel Speed: 9150 - 18300 RPM - Power: 0.4 kW - Weight: 0.5 tons Equipped with: - Pneumatic centering device
Grinding wheel dimensions (od x id x width): 325 x 175 x 125 mm, Ø min/max to be rectified: 1.5 / 50 mm, Regulating wheel width: 125 mm, Regulating wheel dimensions (od x id x width): 220 x 125 x 125 mm, Grinding wheel width: 125 mm, Grinding wheel head motor power: 7,5 Kw, Long: 1.520 mm, Width: 1.020 mm, Tall: 1.260 mm, Weight: 1.600 Kg
grinding diameter: 630 mm grinding length: 600 mm centre height: 320 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Maschine wird überholt nach Kellenberger Messprotokoll und neu lackiert. Die anfällige Güttinger Steuerung wird durch die zeitgemäße BEMA X Steuerung ersetzt. Das heißt die Maschine erhält in diesem zuge auch eine komplett neue Elektrik. Siehe Beispielfotos. Maschine mit verstärktem Werkstückspindelstock zum fliegend Schleifen von schweren Werkstücken. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Grinding wheel dimensions (od x id x width): Ø300 x Ø175 x 125 mm, Ø min/max to be rectified: 1.5 - 50 mm, Regulating wheel dimensions (od x id x width): Ø220 x Ø125 x 125 mm, Grinding wheel width: 125 mm, Number of revolutions engine power: 2,100 rpm, Grinding wheel head motor power: 7.5 HP, Total power: 8,5 Kw, Weight: 1.450 kg
Grinding wheel dimensions (od x id x width): 325 x 175 x 125 mm, Ø min/max to be rectified: 1.5 / 50 mm, Regulating wheel width: 125 mm, Regulating wheel dimensions (od x id x width): 220 x 125 x 125 mm, Grinding wheel width: 125 mm, Grinding wheel head motor power: 7,5 Kw, Long: 1.520 mm, Width: 1.020 mm, Tall: 1.260 mm, Weight: 1.600 Kg
Grinding wheel dimensions (od x id x width): 325 x 175 x 125 mm, Ø min/max to be rectified: 1.5 / 50 mm, Regulating wheel width: 125 mm, Regulating wheel dimensions (od x id x width): 220 x 125 x 125 mm, Grinding wheel width: 125 mm, Plow (auto/manual): Automatic, Maximum length to be rectified in plongeé: 125 mm, Grinding wheel head motor power: 7,5 Kw, Long: 1.520 mm, Width: 1.020 mm, Tall: 1.260 mm, Weight: 1.600 Kg
Grinding wheel dimensions (od x id x width): 325 x 175 x 125 mm, Ø min/max to be rectified: 1.5 / 50 mm, Regulating wheel width: 125 mm, Regulating wheel dimensions (od x id x width): 220 x 125 x 125 mm, Grinding wheel width: 125 mm, Grinding wheel head motor power: 7,5 Kw, Long: 1.520 mm, Width: 1.020 mm, Tall: 1.260 mm, Weight: 1.600 Kg
Universal cylindrical grinding machine for external and internal grinding with accessories Features: - Automatic grinding cycles - X/Z axes electrically controlled - Table can be swivelled up to 30° - Swivelling grinding head - Short changeover times from external to internal grinding - Easy to use - Compact design Hours: 12936 Weight: 2300Kg Technical data: see picture Further details on request
Monzesi Rossi Monza 500 centerless grinding Grinding wheel 250 500, Recent Electric retrofit The machine is in our warehouse in Gussago BS, under power M i m u machine tools, Centreless grinding is a procedure for grinding cylindrical bodies and is used for mass production of rollers, cylindrical, conical rollers, jet needles, pump pistons, hydraulic sliders, crosses, drills etc., During centerless plunge grinding, the workpiece is ground in one pass, thanks to the translation of the grinding wheel. For this purpose, the grinding wheels and the adjustment discs have a negative profile of the piece, to work which is given to them with the aid of a tool., The through-feed grinding or also through grinding and longitudinal grinding: pieces, to be worked proceed uninterruptedly with axial feed through the rectification gap.ith axial advancement through the grinding gap.
grinding diameter: 250 mm grinding length: 400 mm centre height: 125 mm Control: Fanuc 21i-T total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Maschine gewartet und teilüberholt. -Neue Schleifspindellagerung -Neue x-Achs Spindel -Obertisch überschliffen -Neue Geometrie Tischgeometrie -Neue Geometrie WSS zu Schleifspindeln B-Achse mit 1° Hirth Verzahnung Längspositionierung HF-Innenschleifspindel GAP Papierbandfilter The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
working area: mm speed: m/min Bar length: mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Manufacturer: Ziersch Model: ZT 820 Year of Manufacture: 2008 Type of Machine: Grinding Machine Certification: CE Marked Find more here - .ucymachines/ Contact us at - sales@ucymachines
Inv. Num. : 8195 Type: AR35 Type 11 Producer: Reform Created: 1998 Parameters: Control system: Sinumeric 805 Magnet: 3500 x 700 mm Machine height: 3000 mm Machine length: 8800 mm Machine width: 2250 mm Machine weight: 28000 kg
Dimensions: 1520x1020x1260mm, Weight: 1550 kg, Grinding wheel gap: 1.5/50mm, Ø min / max to be rectified: 1.5/50mm, Max.width of wheel in feed grinding: 125mm, Max. width of grinding wheel in plunge grinding: 125mm, Working wheel dimensions (od x id x width): 300x125x175mm, Øext.min. working wheel: 220mm, Min. ext. Ø of the working wheel: 220mm, Max. profile depth of the working wheel: 8mm, Max. depth of working wheel profile: 8mm, Driving wheel dimensions (od x id x width): 220x125x125mm, Drive wheel dimensions (OD x ID x W): 220x125x125mm, Min. ext. Ø of the drive wheel: 165mm, Øext.min. driving wheel: 165mm, Max. depth of the drag wheel profile: 8mm, Driving wheel motor power: 0,75Kw, Working wheel motor power: 7,5Kw, Drive wheel motor power: 0,75Kw, Angle of inclination of the working grinding head: +/- 5º, Angle of inclination of the drive wheel head: -2/+5º, Angle of inclina ...
PART NUMBER: 7549 Specifications: - max width of the workpiece 1100mm - max height of the workpiece 170mm 2 units: 1) grooved rubber roller for calibrating 2) rubber roller + boot boot + metal roller –in advance: - metal roller, slip - aggregate - metal roller, slip - A unit with a shoe - metal slip outfeed roller – from below: - Pulling strap - pneumatic oscillation of the belts - electric lifting of the table top - 2 types of feed speeds - 11kW motor - with pneumatic brake - working pressure 6-8bar - extraction spigot diameter 2x150mm - total dimensions length/width/height 1960x1700x2000mm - weight about 2000kg ADVANTAGES – made in Germany – 2 units – unpainted – used grinder, very good condition Net price: 34900 PLN Net price: 8116 EUR depending on the price 4.30 EUR (Prices may change with higher fluctuations)
Universal tool and cutting grinding machine TACCHELLA 4 AM - Universal device, Hydraulic movement of the table., Information about technical data are not binding., Machine available subject to prior sale., Longitudinal travel x axis: 400 mm, Cross travel y axis: 250 mm, Clearance between worktable and spindle axis: 375 mm, Wheel speed: 3000/6000 rpm, Wheel dimension: 200x20 mm, Spindle motor power: 1,5 Kw, Weight: 1150 Kg, Accessories: Cooling system, motorized dividing device
grinding length: 600 mm grinding width: 250 mm workpiece height: ca. 385 mm table surface area: 600 x 200 mm table speed -stepless-: 2 - 35 m/min table load capacity: max. 250 kg grinding wheel size: ø 225 x 25 mm grinding wheel hole diameter: 50,8 mm vertical feed autom.: 0,001 - 0,099 mm rapid traverse vertical: 600 mm/min cross feed of table continual: 10 - 1000 mm/min rapid traverse cross: 1000 mm/min total power requirement: 6 kVA dimensions of machine L x W x H: 2,65 x 1,70 x 2,28 m Accessories: DRO on Y-and Z-axis, magnetic plate 600 x 200 mm, grinding wheel with flange, wheel trueing attachment, wet grinding attachment with paper band filter The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding length: 600 mm grinding width: 300 mm workpiece height: 350 mm total power requirement: ? kW weight of the machine ca.: 2,5 t dimensions of the machine ca.: 2,522 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding length: 8400 mm grinding width: 1450 mm workpiece height: 1250 mm surface area: 8000 x 1250 mm table height over floor: 920 mm distance between columns: 1470 mm workpiece weight max.: 59700 kg weight of the machine ca.: 59,7 t dimensions of the machine ca.: 22 x 5 x 5 m Adjustment ranges: -Crossbeam, vertical 1250 mm -Grinding support, horizontal 3100 mm Adjustment speeds: -Machine table (X-axis) infinitely variable 1-45 m/min Table creep speed 5 m/min -Grinding support, horizontal (Y-axis) Rapid traverse 3000 mm/min Feed, step 0.001-0.099 mm Feed rate, continuous 100-3000 mm/min Creep speed 18+1 mm/min Tip infeed 0.001-0.019 mm -Crossbeam (W-axis) Rapid traverse 410 mm/min Table drive: -Oil transmission, Type Iv4 -Cylinder-Ø 185 mm -Piston rod Ø 130 mm -Drive motor 22 kW The data for this ad was created with ModulMWS - the ...
: 0600 mm : 300 mm : 342 mm : 700x340 mm : 355x38x127 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 0800 mm : 400 mm : 342 mm : 900x460 mm : 355x38x127 mm : 2400 U/min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Maximum length of the piece: 1100 mm, Minimum length of the piece: 50 mm, Maximum diameter of the piece: 125 mm, Minimum diameter of the piece: 8 mm, Center height of tailstock above guide: 145 mm, Center height of tailstock above carriage: 65 mm, Centering hole taper angle: 60°, Larger diameter of centering hole cone: 50 mm, Diameter of smallest centering hole: 2 mm, Grinding spindle speeds: 45000 / 22 500 / 13 000 rpm, Hollow screw speed: 400 rpm, Stroke of the grinding wheel along the grinding surface: 0.75 - 5 mm, Diameter of grinding wheels: 15, 27, 48 mm, Weight approx.: 460 kg, Dimensions (length x width x height): 850 x 750 x 1850 mm
grinding diameter: 630 mm grinding length: 600 mm centre height: 320 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Machine with heavy duty workhead. Machine will be partial overhauled before delivery. Machine will get a geometry protocoll according to the Kellenberger new machine guideline The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
TOS BUC 63A/3000 Cylindrical Grinding Machine Grinding Diameter 630 mm Grinding Length 3000 mm Height of centers 315 mm Workpiece Weight 2500 Kg Max. Grinding wheel dimensions 750 x 100 x 305 mm Spindle Speed 840/970 rpm Workpiece Spindle Speed 8 - 315 rpm Grinding support stroke 90 / 280 mm Table Speed: Variable - from 0.01 to 3.6 m / min Grinding Head Swivel 90 Degree Table Swivel +/- 5 Degree Work Head Tilts from 90 taper - Morse 6 Spindle Drive 15 KW Machine Dimensions 10000 x 3400 x 2000 mm Machine Weight 13.7 Ton Machine weight approx. 12 t Space requirement approx. 12 x 4.3 x 1.9 m Total power input 22 kW
Sell some machines from our warehouse because we need the space to expand
SPECIFICATIONS: Machinable tool: max. Ø 300 mm Tool length: max. 240 mm Installed power: 1.1 kW EQUIPMENT: Different types of grinding wheels
Travel paths X/Y/Z: 900 x 400 x 200 mm Table size 800 x 400 mm
grinding diameter: 250,350,450 mm grinding length: 1000 mm centre height: 125,175,225 mm grinding wheel diameter: 400 mm grinding wheel width: 50 mm bore: 127 mm : MK5 work piece spindle speed: 20-400 U/min workpiece spindle - bore: mm grinding head swivelling: 360 ° grinding spindle head - swivable: 180 + - ° grinding spindle speed: 1500,1700,2200 U/min : 0,001-0,030 mm/Ø : 0-0,95 mm/Ø : ±8 ° longitudinal feed of the table: 1300 mm table speeds: 0,02-6 m/min : 130 kg : 130 inkl. Spannugkg kg : mm grinding depth: mm : 70 mm total power requirement: 6,5 kW weight of the machine ca.: 2,5 t dimensions of the machine ca.: 4,2 x 2,0 m Ready for delivery, with 12 month warranty in germany and neighbouring countries! Geometrically overhauled and repainted with new electrics. In KELLENBERGER quality! -Digital display in 2 axes. Resolution x-axis 0.5my -Modern workpiece headstock with cone ...
Machine Table size approx. 2500 mm x 980 mm
Manufacturer: Tagliabue, Type: L 600, Year: 1998, Monting of the machine: Walze/Walze, Sanding width mm: 600, Sanding hight mm: 0,5-30, Number of sanding belts: 2, Continous adjustable feeding speed m/min: 5-20, Feeding engine kw: ca.2, Sanding belt dimensions: ca.2620 X 630, Sanding belt speed m/sec: 2 Stufig, Power belt 1 in kW: ca12, Performance in kW belt 2: ca.12, Constant table hight: yes, machine ready for demonstration: yes, Year :1998
Manufacturer: Weber, Type: K 1-1100 V, Year: 2001, Monting of the machine: Walze, Double sided sanding line: no, Sanding width mm: 900, Sanding hight mm: 100, Number of sanding belts: 1, Continous adjustable feeding speed m/min: 2 - 14, Feeding engine kw: 1,3, Sanding belt dimensions: 2.620 x 1.150, Table hight adjustment by engine: no, Rollers: 1, Power belt 1 in kW: 15, Intermediate sanding of lacquer: no, Vacuum table: 2,2, Noise enclosure: yes, Brushing unit: 0,55 kW, Year :2001
grinding length: 2000 mm grinding width: 600 mm workpiece height: mm Control: total power requirement: 17 kW weight of the machine ca.: 10 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Working width: 1.100 mm Number of sanding units: 2 st. Workpiece thickness max.: 150 mm sanding belt measurements: 1.110 x 1.900 mm Motor roller: 15 kW Motor pad: 11 kW Feed motor: 1,5 kW Feed speed: 3 - 15 m/min. Overall size: 1.750 x 2.210 x 2.280 mm Weight: ca. 3.300 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding length: 6100 mm grinding width: 350 mm workpiece height: 300 mm Control: total power requirement: 75/92,5 kW weight of the machine ca.: 20 t dimensions of the machine ca.: 12.500 x 1.800 x 2.600 m Brand Reform Machine no 2050-SL377 Type AR 61 Type 8/CNC CNC Brand Siemens CNC Type Sinumerik 805 Year of make 1997 Machine weight 20.000 kg Horizontal Grinding length 6.100 mm grinding width 350 mm Grinding height 300 mm Engine power 75 / 92.5 Kw Automatic depth feed Grinding stone diameter 600 mm ø Magnetic plate size 5x 1.200 x 350 mm Cooler with magnetic filter Machine size (lxwxh) 12.500 x 1.800 x 2.600 mm 5x Magnetic plate, adjustable in degrees. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Reishauer RZ 362A Built in 1999 Accessories: 2x Fässler dressing device Diamond Wheels Whetstones Turbo separator
Key data: 1340 mm, 150 mm
SPECIFICATIONS: Machining width: 1340 mm Processing height: 150 mm Steel calibration roller: Ø 200 mm Sanding belt length: 2100 x 1400 mm Installed power: 17 kW
Doubleside glass grinding machine Min glass dimention 160x160mm Glass thickness 3-30 mm
Spline shaft Grinding machine STANKO 3M451B/1500 with accessories.
Inv. Num. : 8313 Type: 1500 R Producer: Kellenberger Created: 1972 Parameters: Table dimensions: 2060 x 140 mm Maximum grinding diameter: 250 mm Max. grinding length: 1500 mm Length: 3270 mm Width: 1600 mm Height: 1650 mm Weight: 3250 kg Equipment: DRO
Surface Grinding Machine Manufacturer: Geibel + Hotz Type: FS 40 AC Year of Make: 1998 Table length: 400 mm Table width: 200 mm Workpiece weight max. on the table: 150 kg Grinding wheel diameter: 225 mm Grinding wheel width: 25 mm Grinding wheel bore: 51 mm Machine weight approx.: 1,050 kg Machine dimensions LxWxH: 1,800 x 1,200 x 2,250 mm
Key data: 3000 mm, 850 mm
Crankshaft Grinder BERCO RTM 425 Center height mm.425 Max swing mm.850 Center distance mm.3000 Wheel flanges Rests Machine dimensions mm.7100 x2350 Weight approx Kg 9000 Perfect working condition
grinding length: 600 mm grinding width: 200 mm workpiece height: mm total power requirement: 7,5 kW weight of the machine ca.: 2,3 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Specifications: - Sanding belt dimensions approx. 2000 x 150 mm - Surface grinding opening approx. 560 x 150 mm - Sanding belt speed approx. 30 m/sec. - Contact washer B 150 / D 200 mm - Drive pulley B 150 / D 200 mm - Drive 400 V / 3 kW - Working height adjustable -Mot. Dust extraction - Space requirement approx. W 750 x H 1050 x D 1500 mm - Weight approx. 120 kg
External/Internal Cylindrical Grinding GENDRON RU 28.100 Between points: 1000 mm Maxi grinding diameter: Ø 290 mm Tool holder rotation: from 70 to 370 RPM 4-jaws Ø 200 mm chuck Grinding wheel: Ø 300 mm Auto pass plug Swivel table External hydraulic group External lulbricant tank Voltage: 380 V Dimensions (L x W x H): 3000 x 1900 x 2000 mm Weight: approx 3 T
maximum number of results exceeded
please refine your search
