thread rolling used for sale

Qty. 1 Second-hand Sendzimir Cold Rolling Mill Mfc.: INNSE Type: ZR23 C-25 – 20-Hi Built: 1977 Stopped: 2025 Steel grades: HSLA, low and high carbon steel, etc. Strip width: 300 - 650 mm Thickness: 0.05 – 3.0 mm Max. tensile force: 15.000 kg Coil weight: 10 T AGC & PLC system: ABB

A dough sheeting machine Fritsch for folded dough sheets for subsequent processing is available. Belt width: 700mm, working width: 650mm, roller gap range: 0.3mm-50mm, roller diameter: 98mm, max. dough block weight: approx. 20kg, belt speed: 50m/min, machine dimensions X/Y/Z: approx. 3300mm/1250mm/1550mm, weight: approx. 500kg. An on-site inspection is possible.

Qty. 1 Second-hand 2-Hi Skin Pass Rolling Mill Mfc.: Sir James Farmer Norton Type: 2 - High Temper Mill 318/610 x 710 mm Built: 19 Stopped: 2025 Strip Width: 300 – 600 mm Thickness: 0.3 – 4.0 mm Max. Tensile Force 3000 kg, Coil weight: 10 T

A granite three-roll mill, presumably made by Bauermeister, which was used for marzipan, is available. On-site inspection is possible.

Qty. 1 Second-hand Reversing 4-Hi Cold Rolling Mill Mfc.: NKMZ, ABB, Grip Engineering, Launer Engineering Built: 1972 Type: Reversible Cold Rolling Mill (Quarto-1800) The cold rolling stand has been modernized by ABB in 1995. The mill was fitted with automatic gauge control (AGC), flatness control unit (AFC), spot cooling system (by Grip Engineering), and work roll changing device (by Launer Engineering). Besides, the mill has been equipped with a horizontal rolling Oil filtration system (by Launer Engineering). Flatness & AGC control: available /1995

Rolling mirror approx. 50x175h cm

Dimensions per tray: 2000 x 1300 mm with a total of 40 sheeting trays Reference: Pieper - Lot 9 Auction-ID: A7-46763-5

Total load 200 kg, floor load 80 kg Auction-ID: A1-46781-20

Equipped with drive! Approx. 2 to 4 tons; remote control included; Auction-ID: A1-41997-96

Viewing by appointment Auction-ID: A1-43891-34

Viewing by appointment Specification Value Type Vibratory Pneumatic Tire Roller Operating weight 8,500 kg Max. ballast weight 9,100 kg Power 77 kW / 103 hp Speed max power 1600 rpm Drive Hydrostatic, AWD Speed up to 9 km/h Climbing ability 38% Working width 1960 mm Total width 2200 mm Total length 4540 mm Altitude (ROPS) 2995 mm Wheelbase 3000 mm Ground clearance 285 mm Fuel tank 130 litres Hydraulic tank 65 litres Water tank spray system 600 litres Tire configuration 3 front / 4 rear Tire size 17/70-20-12PR Auction-ID: A1-43891-32

Brands E.W. Menn / Ingramatic / P&E / Hilgeland Diameter ranges from 1 mm - 20 mm

Thread cutting power M 2 - M8 Speed: 700 rpm, luf requirement: 750 l/min, pressure 6 - 7 bar, working range extension: 300 - 1900 mm, Afbau parallel arm: stable arm structure made of hard aluminium profile (38x29) Weight: 23 kg, adapter holder: TCS 1 B - incl. 6 safety slip couplings according to your choice year: 2009

Thread cutting capacity: M 3 - M 12 Speed: 400 rpm Air demand: 750 l/min Pressure: 6 - 7 bar Extension: 950 mm Standard accessories: Parallel arm Air motor 6 pcs safety slip couplings of your choice guide column with mounting flange Radial boom Maintenance Pneumatic oil for initial filling

Threaded drilling machine with up to 10 spindles, adjustable drilling pattern

Machine is used for the processing of pipe and pipe components, including thread cutting in terms of the single and mass production. Diameter range of processable pipes: 70-290 mm Max diameter of processable work-piece: -Over stand: 800 mm -Over support: 450 mm Diameter of spindle hole: 300 mm Max turning length: -With bevel ruler: 800 mm -W/O bevel ruler: 420 mm Amount of spindle speeds: 12 Limits of spindle rotation frequency: 8-355 turn/min Amount of longitudinal and cross support servings: 32 Limits of: -Longitudinal servings: 0,064-1,025 mm/turn -Cross servings: 0,034-0,458 mm/turn Step limits of cuttable: -Metric threads: 1-12 mm -Inch threads (amount of threads for 1): 2-24 Max turn angle of bevel ruler: +- 10 degrees Overall machine dimensions: -Length: 3600 mm -Width: 1860 mm -Height: 1525 mm Machine weight with electric equipment: 9050 kg

STANKOIMPORT 5822M thread grinding machine was manufactured in the USSR. The machine is used for the process of grinding threads to give them the correct dimensions and roughness. During this process, a grinding wheel with a diameter of 400 mm is used to remove a small allowance from the workpiece, forming the thread shape on it. The grinding machine processes threads with a maximum diameter of 200 mm, a length of 500 mm and a weight of up to 30 kg. Depending on the choiceed disc, the diameter of the workpiece can be from 3 to 150 mm (grinding with a single-coil disc) or from 10 to 120 mm (grinding with a multi-coil disc). The total weight of the grinding machine is approximately 5 tons. Technical data of the STANKOIMPORT 5822M thread grinding machine - maximum workpiece diameter: 200 mm - diameter of the workpiece grinded with single-coil disc: 3-150 mm - diameter of the workpi ...

Semi-automatic short-threaded cutting machine for the production of external and internal thread Gr. via cross slide: 160 mm Gr. via cross slide guide: 240 mm tip wiete 250 mm nSpindle=180-2240 rpm spindle bore: 61 mm gr. threaded length/deep 100/6 mm

Assembly angle on both sides with threaded plates brand: Otto Kraft height 835mm ; Width 550 mm ; Length 450 mm plate size 750 mm x 500 mm All details without gewaehr

Huller thread cutting machine vith hydraulic vice. Thread head from M3 up to M27 Machine is perfect for serial work.

MOSCOW 582 thread grinding machine was manufactured in the USSR. Technical data of MOSCOW 582 thread grinding machine - grinding diameter: 250 mm - grinding length: 500 mm - tooling (divider, fang, changewheels) - dimensions: 260 x 220 cm

Thread cutting head with chaser jaws, thread cutting stock, thread cutting machine, pipe thread cutter, cutting head -Threading head: pipe thread -Measurements: see pictures -Price: per piece -Number: 4 pieces -Dimensions: 340/250/H60 mm -Weight: 6 kg/piece

Micrometer, micrometer screw -Measuring range: 75 - 100 mm -Handover: as is as seen -Accessories: missing, see photo -other sizes: available -Dimensions box: 265/145/H30 mm -Total weight: 0.7 kg

Micrometer, micrometer screw -Measuring range: 75 - 100 mm -Accessories: see photo -other sizes: available -Dimensions box: 265/125/H25 mm -Total weight: 0.8 kg

Tapping machine, pipe thread cutter -for: pipe size max. 2 inches -Speed: 72 rpm -Foot switch with: emergency stop function -Pipe cutter -Interior deburrer -Operating voltage: 220 volts -Dimensions: 1100/560/H1140 mm -Weight: 126 kg

Tapping machine, pipe thread cutter -without tools -Operating voltage: 220 volts -Dimensions: 830/530/H1080 mm -Weight: 64 kg

Thread cutting head with chaser jaws, thread cutting stock,Tapping machine, pipe thread cutter, cutting head -Thread cutting head: 1/2- 2 -Cutting jaws: R1 -1 1/2 -Dimensions: 870/110/H200 mm -Weight: 11 kg

Micrometer, micrometer screw -Measuring range: 125 - 150 mm -Handover: as is as seen -Accessories: missing, see photo -other sizes: available -Dimensions box: 330/180/H30 mm -weight: 1.1 kg

Tapping machine, pipe thread cutter -for: pipe size max. 2 inches -Speed: rpm -Foot switch with: emergency stop function -Pipe cutter -Interior deburrer -Operating voltage: 230 V -Dimensions: 1200/560/H1250 mm -Weight: 133 kg

Tapping machine, pipe thread cutter -for: pipe size max. 2 inches -Speed: rpm -Foot switch with: emergency stop function -Pipe cutter -Interior deburrer -Operating voltage: 220 V -Mechanics for: cutting jaws missing -Dimensions: 1100/700/H1130 mm -Weight: 132 kg

Tapping chucks, tapping chucks, tapping chucks -Tapping chuck: with return -with: slip clutch -Cutting capacity: M8-M18 -Recording: MK3 -Quantity: 1x thread cutting chuck available -Price per piece -Weight: 3.4kg

Thread cutting head with chaser jaws, thread cutting stock, thread cutting machine, pipe thread cutter -Inch thread: 1/4 - 1 inch -Dimensions: 550/120/100 mm -Weight: 4.7 kg

Thread edge with extensive accessories, by hand or automatically to use. Table model, mobile also for the construction site Manufacturer GF Georg Fischer Table model with electric drive or by hand. Automatically opening thread cutting head Threaded jaws for: 1/2 inch, 3/4 inch, 3/8 inch, 1 inch, 1 1/2 inch, 2 inch Machine in transport box (steel) Rems Tornado Klauke Rothenberger Supertronic Special price

Thread cutting head with chaser jaws, thread cutting stock, thread cutting machine, pipe thread cutter -Inch thread: 1/4 - 1 inch -Dimensions: 385/120/110 mm -Weight: 5.1 kg

Thread cutting head with chaser jaws, thread cutting stock, thread cutting machine, pipe thread cutter -Inch thread: 1 -2 inches -Dimensions: 640/160/H130 mm -Weight: 8.7 kg

Cutting stock set, hand pipe thread cutter, thread cutting machine, pipe thread cutter, pipe thread cutter, cutting head, tap wrench -for square up to: 34 mm -Price: per piece -Quantity: 2 pieces -Dimensions: 1005/85/H35 mm -Weight: 4.7kg

Tapping machine, pipe thread cutter -for pipe size: max. 2 inches -with: cutting jaws -Speed: rpm -Foot switch with emergency stop function Pipe cutter -Interior deburrer -Operating voltage: 220 volts -Dimensions: 1200/660/H1250 mm -Weight: 166 kg

Ball valve, ball valve internal thread -Pressed brass -Internal thread: 2 inches -full: passage, full ball -Number: 63x ball valves available -Price: per piece -Weight: 2.1 kg

Clamping plate with T-slots, plate field, welding table, welding table, pallet changer -comes: from a CNC machining center -Width: 440 mm -Length: 400 mm -with: support ribs -with: instep index -Number: 2x plates available -Price: per piece -Weight: 74 kg

Specifications: Model: RNR 20-600 Machine No.: 8266 Item no.: 511061 Year of construction: 2021 Working range: Radius 1800mm RPM speed: 600+170 (with intermediate gear) Torque in Nm: 19/67 Recording: Gr. 2 Ø 31 Capacity St.40: M3-M20 Air consumption approx.: 650 l/min Required air pressure: 7kgr/cm2 Standard - Pneumatic motor (pot make: Ingersoll-Rand) - Engine lubrication - Pressure reducing valve and moisture separator - Quick-change mount for e.g. Bilz thread holders - Flange for mounting on the table - Microspray system for thread cutting (integrated in the machine head) Accessories: - 1x 2-1 reduction - Thread cutting holder with slip clutch for the following threads: 1 / Ø 19 2/ Ø 31 M4 Ø 2.8 ■ 2.1 M8 Ø 6 ■ 4.9 M5 Ø 3.5 ■ 2.7 M10 Ø 7 ■ 5.5 M6 Ø 4.5 ■ 3.4 M12 Ø 9 ■ 7 M14 Ø 11 ■ 9 M16 Ø 12 ■ 9 M18 Ø 14 ■ 11 M20 ...

Offer via gebr. Thread cutting machine with pipe saw RA21 Made GEORG FISCHER type KM2, built 1997 Technical data: Thread diameter 3/8" - 2" Power connection 200 - 240 V / 50 Hz With mobile undercarriage with threaded cutting jaws 3/8", 1/2", 3/4", 1", 11/4", 11/2",2" used, in good condition.

Thread cutting dies, replacement dies, thread cutting heads with chasers, thread cutting stock, thread cutting machine, pipe thread cutter -various: thread cutting sizes -Price: complete -Weight: 12 kg

thread dia.: 12 mm threading length: 20 mm turning speeds: 400 U/min working area: 500 - 1600 mm weight of the machine ca.: 25 Kg dimensions of the machine ca.: m • pneumatical thread cutting device, M3 - M12, • with 6 adapters of thread cuttings, Size 1, • control valve with lubrication, • order no. 31681, The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

90m Trapezoidal threaded spindle, steel, warehouse liquidation, TR30x6 bis TR10x3, , new -75% Single-start, rolled threaded spindles with trapezoidal thread according to DIN 103, in material C35/C45, in many sizes between TR10x3 to TR30x6. Special price These threaded spindles come from a stock liquidation, therefore we offer a bundle with spindles for an absolute special price. The current purchase price of these threaded spindles is € 2354 excl. VAT Our selling price is only 25% that is € 588 excl. VAT Attention: The photos do not correspond to the indicated quantity Scope of delivery: appr 180kg TR30x6 right: 3x780mm TR28x5 right: 1x1940mm, 1x1180mm TR26x5 right: 6x950mm, 1x850mm, TR26x5 left: 1x1900mm, 3x1000mm, TR24x5 right: 2x1570mm, 1x1700mm, 2x840mm, TR24x5 left: 2x2000mm, 1x1120mm, 1x840mm, TR22x5 right: 1x2000mm, 1x790mm TR20x4 right: 1x2000mm, 1x ...

PLC – controlled universal thread chasing machine suitable for all external and internal threads, as well as for peeling operations on rods and shafts (with peeling heads of different sizes), with 7" color touch screen. External and internal threads from M10 to M60 can be cut with the machine on all rotationally symmetrical workpieces such as pipes, bushings, shafts and reinforcing steel rods (taped external threads, drilled internal threads or rolled external threads with rolling heads). All thread types - male and female - metric ISO thread - Whitworth thread - trapezoidal thread - pipe thread - round thread - saw thread - UNC/UNF - and other USA threads etc. Strehlkopf speeds infinitely variable from 25 to 300 rpm Hollow spindle bore Ø 64 mm Maximum thread length 300 mm in one clamping (optional up to 600 mm length) The strehlkopf can also be used to peel wave-shaped  ...

Thread cutting machine, pipe thread cutter, thread cutting head with Strehler jaws, thread cutting die, thread cutting machine, pipe thread cutter -for: Pipe size: max. 2 inches -Cutting jaws: 1/2-2 inch -Operating voltage: 240 volts -Dimensions: 1000/600/H1114 mm -Weight: 80 kg

Tapping machine, pipe thread cutter -for: pipe size max. 2 inches -Cutting jaws: 1/2 , 3/4, 1 , 1 1/4, 1 1/2 -Dimensions: 510/360 / H240 mm -Weight: 64 kg

Thread cutting machine, pipe thread cutter -for: Pipe size max. 2 inches -Cutting jaws: 1/4 - 2 -Dimensions: 510/360/H240 mm -Weight: 64 kg