127,837 used machines on RESALE, but how to find them? Machine Search
pressure: 140 t chamfer lenght: 3000 mm distance between columns: mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Stocknumber 2010012 Type of machine Pressbrake Make COLLY Type 3000/140 Build in nb Chamfer lenght 3000 mm Pressure 140 ton Stroke 250 mm Throat 310 mm Daylight 520 mm Additional information incl. 1 set of tooling The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3050 mm plate thickness: 53 mm pre-bending: 45 total power requirement: 60 kW weight of the machine ca.: t dimensions of the machine ca.: m Stocknumber 2210020 Type of machine 4-Roll Plate Bending machine Make DAVI Type MCB 3053 Build in 1998 Type of control Conventional Additional information max. Plate widht 3050 mm Max. plate thickness 53 mm Max. thickness prebending 45 mm Toprol diameter 525 mm under roll diam. 470 mm Site rolls diam. 400 mm Power 78 Hp Hardened rolls Conical bending Dimensions: 6000 x 3100 x 6700 mm in very good condition The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 800 KW, 1000 kVA, 400 V
NEW/Surplus MWN 3016 V 16, 800 kW, 400v. 50 Hz. CHP Enclosed Natural Gas Generator Set Rating: 800kW, Electric Power: 800kWe Power factor (cos. phi): 1.0, 400 Volts, 3Ph, 50Hz, 1500 Rpm Altitude: max 1100m a.s.l., Ambient temperature: +5 up to +53 degC Engine: MWM 3016 V 16, 16 cylinders in V, water cooled, turbo charged with intercooler Alternator: 800kW / 400V synchronous, 3 phases, brushless, self-exciting, self-regulating, air cross flow ventilated, protection mode IP23, engine flywheel and generator shaft coupled, engine and generator coupled over SAE flange and fixed to one unit, genset mounted with vibration dampers. Control unit MMC consisting of: Electronic speed regulation for the engine, Cos. phi regulation for the engine, Complete engine monitoring and control, Complete generator monitoring, Display of all relevant data (voltage, frequency, power, temperatures, oil pr ...
sheet width: 3000 mm plate thickness: 10 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 9,8 t dimensions of the machine ca.: 4,15 x 3,55 x 2 m Brand: Durma Type: DHGM 3010 Year of make: 2002 Knife length: 3.000 mm Plate thickness: 10 mm Electric backstop Machine dimensions (lxwxh): 4.150 x 3.550 x 2.000 mm Machine weight: 9.800 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Properties Volume 7300 L Material V2A (AISI 304) 1.4301 Vertical design Last Use Food Number of feet 3 Total height 3550 mm Height 2720 mm Diameter width 2550 mm Weight 450 kg Surface inside IIID Surface outside IIID marbled Description Topsoil: curved bottom 2 crane eyes Upwardly drawn surround with threaded nozzle DN 50 for airlock Tank cylinder: Level indicator with bar and scale with standpipe valve DN 15 Manhole 430x330 mm Sample tap DN 20 Ladder hook at the top Clear drain with inclined seat DN 50 Subsoil: curved bottom forward-drawn outlet surround Forward-drawn floor bead with disc valve DN 50 3 shell feet with calottes - height adjustable
; Power [PS]: 326; Gross weight [kg]: 3404; Engine: Caterpillar C9; Accessories: Tanker, Battery, Control Panel, Stahldach, Including: battery charger and coolant heater; Water Tank Volume [l]: 610
Centrifugal pump Manufacturer: Hilge Type: Hygia II/30C Power: 11 kW Speed: 2930 rpm LBH: 650 x 400 x 410 mm
ALL STAINLESS STEEL Hopper capacity : 300 l Two levels of hopper Two working shafts with paddles Front discharge of ready product in 200 l trolley Programming controller Power – 4 kW Machine dimensions in cm: Width: 95,0 Length: 154,0 Height: 156,0 Weight - 500 kg OPTION :Loading unit 200l trolleys: Column loader dimensions in cm: Width: 110,0 Length: 120,0 Height: 238,0 Column loader power 0,8 kW
TO WHOM AT MAY CONCERN ; WE VE NEW UNUSED 3 SETS NAPIER NA 307 GAS INLET& OUTLET CASINGS AND INLET ELBOWS AT OUR STOCK. 3 SETS GAS INLET & OUTLET CASINGS ARE NEW AND NEVER MONTAGED . PLS REFER SOME PICTURES ON ATTACHE IF YOU VE ANY QUESTIONS . PLS DO NOT HESITATE TO CONTACT WITH US . Capt. Ayhan Ugurluba With Kind Regards ; Aliaga Marine Services E mail: info/aliagamarine.com Phn/Fax:+90 232 618 03 90 Mobile: +905556084850 aliagamarine.com TURKEY
Skid similar but no Dynajet, Oertzen, Falch, DIBO, ... S500-30E-C - High pressure pump: Speck P52/30-500 30l/min. at 500bar (year of construction 12/16) - Motor: Electric 30kW - 400l water tank - Pressure gauge - Pressure regulator - Safety valve - Powder-coated steel frame - Aluminium covers - Forklift tabs - Dimensions with 400l water tank: approx. 1,250 x 1,510 x 1,260 - Empty weight: approx. 700 kg - Year of construction: 2009, new high-pressure pump12/2016 - Operating hours: approx. 1500 h
Dimensions (L/W/H): 800x600x500 mm Weight: 60 kg Total power requirement: 0,25 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Skid similar but no Dynajet, Oertzen, Falch, DIBO, ... S500-30E-C - High pressure pump: Falch xs31.1-30-500 30l/min. at 500bar (year of construction 01/08) - Motor: Electric 30kW - 1250l water tank - Pressure gauge - Pressure regulator - Safety valve - Powder-coated steel frame - Aluminium covers - Forklift tabs and crane eyelets - Dimensions with 1250l water tank: approx. 1,100 x 1,760 x 1,770 - Empty weight: approx. 1,500 kg - Year of construction: 2013 - Operating hours: approx. 1500 h
Dimensions (L/W/H): 0x0x0 mm Weight: 450 kg Total power requirement: 0 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 3030x360x660 mm Weight: 220 kg Total power requirement: 0 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Description: Type : ÖLtransformator Version : Hermetic Make : CG POWER SYSTEMS Belgium NV Year of construction : 2012 Condition : New Rated power : 3500 KVA Medium voltage : 33 KV +- 2 x 5% Low voltage : 400 V Switching group : Dyn 5 Frequency : 50 Hz Cooling type : KNAN Total weight : 7750 Kg Cqs9sygju Oil weight : 1720 kg Synth. ESTER Length : 2400 mm Width : 900 mm Height : 2250 mm + 160mm cable flag Other sizes and voltages also available from 100 KVA to 3500 kva . All transformers are tested and ready for use and immediately available from our warehouse in 59557 LIPPSTADT . Nationwide delivery . For further questions available Mon to Sat. 8 a.m. to 10 p.m.
Many thanks for your interest on our second hand machines, please find follow our offer: Kadema enrober with Original wooden cooling tunnel manufacturer: Kadema; Johannes Kegel Dresden Type: Juwel 305 enrober electrical: 400 VAC / 3 Ph Year of manufacturing: 1930 work width: 305 mm different: With origin wooden cooling tunnel, approx. 8m extendable mass container absolutely in original condition ! We offer this machine in 'as is' condition, without warranty EXW Hess. Lichtenau, (EXW)unpacked
Dimensions (L/W/H): 3030x450x660 mm Weight: 325 kg Total power requirement: 0 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Type: S 300 l 2P-V Complete stainless steel Hopper capacity 300 liter Double working shafts Rotation of shafts in both directions Vacuum: 0,04 – 0,06 mpa Electric power: 4.4 kW Voltage: 380 V / 50 Hz Discharging pneumatic flaps PLC + Touchscreen control Delay start 99 programs Installation dimensions of machine in cm: Width: 135 Lenght: 84 Height: 142 Delivery time: after advanced payment, one working day
Specifications: - Span width approx. 850 mm - Clamping surface height approx. 700 mm - Clamping block depth 300 mm - Total height with clamping base 750 mm - Clamping base dimensions 850 x 450 mm - Clamping holes M16 - Distance of the clamping holes 40 mm - Number of clamping holes per side 336 pcs - Total number of clamping holes 772 pcs - Internal dimensions of the clamping block 380 x 220 mm each - Wall thickness of the clamping areas approx. 40 mm - laterally screwed on 3 jaw lining 300 mm - side-screwed hydr. Machine vice RÖHM - Jaw width 200 mm - Weight approx. 700 kg
Bending Lenght 3050 mm Bending force 135 ton Crowning Type Motorised Controller ModEva 19T CNC back gauge X - R Z manuel
1 used service water pump HABERMANN HPK, power 600 cbm/h, impeller diameter 660, H 33, good condition, E -Motor SONDERMEIER GmbH Type KG315 S/7, 110 kW
Key data: 300
Dürr Eco+Energy ORC 300 HT. 2016 - 500 Hours Model: Eco+Energy ORC 300 HT KWK Year: 2016 Hours: 500 Capacity: 300 kW Hz: 50 Voltage: 400 V Scope of supply: Complete ORC with oil pump skid. Available for Sale. Price: €240,000
RMS Vibration Vibration Test System Here we offer you an RMS Electrodynamic Vibration Vibration Test System. RMS Vibration Vibration Test System Test Manager SWR 900 Vibration exciter SW 3006 30V-50A-3434 N Power amplifier TGA 3000-000.00 Condition: used Unchecked! Tests were not possible Scope of delivery: (See picture) (Changes and errors in the technical data, information reserved!) We are happy to answer any further questions you may have on the phone. Written order possible by email or fax
Dimensions (L/W/H): 4400x4600x3700 mm Weight: 4300 kg Total power requirement: 3,8 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3050 mm plate thickness: 6 mm distance between columns: mm blade length: 3050 mm total power requirement: 11 kW weight of the machine ca.: 7,6 t dimensions of the machine ca.: 2,1 x 3,3 x 1,8 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Vario - Snow removal blade Samasz PSV 301. Universally hydraulically adjustable blade – wedge plough or side clearer left-right use possible. Working width max./min. 303/262 cm, blade height 80/98 cm, rubber skirting strips, special equipment: training wheel set, plough lighting, electric 12 volt cable remote control for light and hydraulic control block. 1 hydraulic connection dw required. Weight approx. 480 kg. Almost new condition. Further snow removal blades, snow blowers and slingshots as well as spreading technology in stock - see also sample photos! Info and offers on request. No sending of package deals or lists. Please name and phone no. for queries. Please let us advise you in advance by phone. Appointment required for viewing!
Vertical basket bottom discharge used centrifuge with scraper, mounted on inertia plate. Type RINA 300F-1000 manufactured by RIERA NADEU. It belongs to the 300 series for liquid-solid automatically separation processes.
sheet width: 3050 mm plate thickness: 25 mm distance between columns: mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 4400x5000x3700 mm Weight: 4500 kg Total power requirement: 3,8 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 2850x2270x2160 mm Weight: 1800 kg Total power requirement: 25,2 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
GRANULATOR / EDGE STRIP CRUSHER The granulator is designed for grinding various plastic waste. Specifications: Motor power: 7.5 KW Capacity: 200 kg/h V-belt: 3 pcs. Speed knife shaft: 715 rpm Blower type: 7,055 kW Housing opening: 300 x 260 mm Rotating knives: 3 Fixed knives: 2 Sieve: 8 mm Weight: 800 kg Connection: 400 Volt, 50 HZ
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
Specifications Cutting width: 3.8×48 mm Year of construction: 1993 Productivity: approx. 40 sheets (DIN A4, 70g/m²) Price: on request Cutting speed: - the safety step: P3 Power supply: 400 V / 2.2 kW We have several channel balers and balers in our warehouse and we cordially invite you to contact us!
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
Dimensions (L/W/H): 0x0x0 mm Weight: 0 kg Total power requirement: 3 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
Rogers 300 HYD Knife Roll Grinder Model: 300 HYD Size 102 Year of arrival at the plant: 1961 Space used by the machine: 7 x 2 x 1,8m Worktable dimensions: 2600 x 250,50 mm. Longitudinal table travel (stroke): 3000 mm. Magnetic system of the table: EML 15 - 115 Volts - 13 Amp - 1500 Watts. Longitudinal slide feed: 0 - 28 m/min. Cross travel without abrasive wheel: 200 mm. Cross travel with new abrasive wheel: 92 mm. Vertical Capacity: 200 mm. Abrasive wheel: Ring abrasive wheel, 26" outer dia., made up of 10 segments type 53 (S/G FLAT RS-801-B) of 6.1/2 "x 2 "x6". Each segment must indicate the maximum RPM for the ring. Abrasive wheel head speed: 560 Rpm. Cooling tank capacity: 259 liters
Dimensions (L/W/H): 2800x1140x1100 mm Weight: 1070 kg Total power requirement: 19 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 1500x1295x1300 mm Weight: 1150 kg Total power requirement: 16,1 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 5500x4000x2250 mm Weight: 8000 kg Total power requirement: 45 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 0x0x0 mm Weight: 0 kg Total power requirement: 3 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Specifications: - Three-jaw chuck 300 mm - Chuck manually rotatable 360° - Division grid 24 - Peak height approx. 185 mm - Duchgang / passage 55 mm - Total depth without baking approx. 270 mm - Total depth with jaws approx. 310 mm - Flange plate horizontal W 300 x D 145 mm - Flange plate vertical W 300 x H 335 mm - Weight 100 Kg - Space requirement W 320 x D 310 x H 335 mm
Dimensions (L/W/H): 5500x3400x1900 mm Weight: 9000 kg Total power requirement: 48 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dimensions (L/W/H): 2860x1140x1100 mm Weight: 1070 kg Total power requirement: 19 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 3000 m³/h power capacity: 2,2 kW Speed: 3000 U/min. : 200 mm Dimensions (L/W/H): 1250x700x2000 mm Weight: 160 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
New industry-standard hotbox for up to 300 bar and up to 28 litres per minute. EQUIPMENT - Epoxy coated steel frame with stainless steel cover - 4-wheel chassis with solid rubber tyres - Connection hose 1,5m - Water inlet temperature max. 60° - Heating capacity approx. 90 kW - Water outlet temperature in the steam range up to max. 140°C - With thermal switch and flow monitor Diesel tank: 20L Power supply: 1x 230V Dimensions: (L x W x H): 700mm x 570mm x 800mm Weight: 65kg Shipping possible. Errors and prior sale excepted. We refer to our terms and conditions.
maximum number of results exceeded
please refine your search
