135,411 used machines on RESALE, but how to find them? Machine Search
Liebherr / Lorenz S800 Gear - Hobbing Machine -Max. workpiece length with counter holder 600mm -Max. workpiece length with retracted counter holder 800mm -Max. travel of the milling carriage 360mm -Largest millable pitch for the largest workpiece 5 Pi / in the normal power range 8 Pi -Pick-up taper - milling spindle MK 5 -Mandrel 22/27/32/40mm -Max. cutter diameter 186mm -Max. cutter length 170mm -Max. cutter displacement 80mm -Milling cutter speeds 40-220 rpm -Feeds infinitely variable / horizontal -Feeds infinitely variable / vertical -Feeds infinitely variable / tangential -Clamping table without water rim 550mm -Clamping table hole 100mm -Mandrel taper MK5 Accessories: 1x pallet interchangeable wheels 1x pallet hob 1x pallet clamping mandrels Documentation Machine feet Dimensions: LxWxH 3.6x1.8x1.9 meters / weight 5000Kg
width of the strips: 100 mm band length: 915 mm dimensions of grinding wheel: 200 mm work table:: 170x125 / 265x150 mm total power requirement: 0,5 kW weight of the machine ca.: 26 Kg dimensions of the machine ca.: 0,6 x 0,5 x 0,3 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Number of boring motors: 1 St. boring of corner bearing 1=yes, 0=no: 1 boring of olive 1=yes, 0=no: 1 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 600 mm y-travel: 400 mm z-travel: 400 mm spindle taper ISO: 40 spindle turning speed range: 80 - 4000 U/min transmission ratio: 18 feed range: 0,1 - 2000 mm/min rapid traverse: x = 4 / y = 3 / z = 5 m/min table load capacity: 250 kp voltage: 380 V / 50 Hz spindle drive: 5,5 kW total power requirement: 16 kVA weight of the machine ca.: 2,6 t dimensions of the machine ca.: 3,8 x 4,3 x 2,0 m • CNC-control system 432 E • Operating hours: 37719 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
JUNG D22 / Internal Cylindrical Grinding Machine -Machine suitable for inner round + surface grinding -Smallest grindable bore 14mm -Largest grindable bore 150mm -Grinding length without face grinding device 250mm -Grinding length with face grinding device -6x workpiece speeds 46-270 rpm -Spindle box right/left swivel 30 degrees -Distance of the spindle axis over the center of the table 250mm -Largest workpiece spindle/grinding support distance 935mm -Spindle box / inclined position 30 degrees each -Work table / tilt forward/backward 5 degrees each -Hand/automatic operation -Taper grinding device -Bezel -Three-jaw chuck -Replacement grinding spindles Dimensions: LxWxH 2.8x1.5x1.8 meters / Weight 3500Kg
plate thickness: 1,6 mm pressure: 450 MPa : 150 x 150 x 90° table surface area: 650 x 500 mm : 875 mm cutting angle - upper blade: 4 ° weight of the machine ca.: 75 kg • manual notching machine with lower frame • sheet thickness (steel 450MPa) to 1.6 mm, aluminium to 2.25 mm, plastic to 3.0 mm, • machine for demonstration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Gate Sharper Manufacturer Vollmer for Inclined and straight ground
Belt Strapping Machine Strap Strapping Device Manufacturer Mosca Verpackungstechnik Maschinenfabrik Gerd Mosca GmbH 69429 Waldbrunn Type RO-TR500-4 Year of construction 2001 Current connection 3 AC 400 Volt Current consumption 1.5kW 50Hz 2.5A PLC Siemens Simatic OP7 The machine can work both manually and automatically. The conveyor belt brings the packaged goods to the right place and the machine then strapping. Operating states Machine An automatic Open a frame Cut off tape
Key data: 630 mm, 2000 mm, 400 mm
Sell a well-preserved lathe from WMW model DLZ 630 x 2000. The machine is in good condition. The dimensions of the machine are LxWxH 4200mm x 1600mm x 1400mm. Spindle passage is 62mm. The machine was completely cleaned. Incl. guideline and sitting skirt. If you have any further questions, please contact us. The machine can be inspected and tested under power by prior appointment. On-site loading is no problem and free of charge. Furthermore, the machine can be delivered in the immediate vicinity and against assumption of costs, with its own truck. A suitable unloading facility must be available for this purpose. The sale is without guarantee and warranty. All information without guarantee.
Bore diameter: , mm Number of heads horizontal: , St. Number of heads vertical: , St. SPINAMATIC mod. GLF-HP Dübeleintreibgerät mit Leimangabe für Fensterfertigung ---------------------------------------------------------------- komplett wie folgt : - Fahrbare Ausführung - Dübelzuführung zur Pistole wird durch SPS-Steuerung gesteuert. - 1 Wendelförderer zur Aufnahme von Dübeln mit 1 Zuführung - Leimanlage ist mit Hoch-Druckpumpe 10:1 und Sonderleimspritzdüse für Dickleim (Typ D3 oder D4-Einkomponent) augerüstet - pneumatische Pistole für Dickleim- und Dübeleinsetzen mit Ausrüstungen für nur einen Dübeldurchmesser nach Wahl zwischen : 6 - 8 – 10 oder 12 mm. Dübellänge : min. 25 mm. – max. 60 mm. Tiefeinsetzen = 30 mm. Der Leim wird durch eine Sonderleimspritzdüse, die mit SPS-Steuerung für elektronische Dosierung in Verbindung ist, gespritzt . - Flexibler Arm mit ...
Number of boring spindles: 1 St. Boring depth max.: 150 mm Motor output: 1,8 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bore capacity in steel (diameter): 25 mm throat: 240 mm bore stroke: 110 mm turning speeds: 125 - 2850 U/min : 310 x 320 mm distance drilling head - clamping area: max. 650 mm total power requirement: 0,75 / 400 kW / Volt weight of the machine ca.: 0,175 t dimensions: 0,95x0,8x1,75 inkl. Tisch m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
width of the strips: 150 mm band length: 2000 mm band speed: 33 m/sec total power requirement: 4 kW weight of the machine ca.: 100 t dimensions of the machine ca.: 1,2 x 0,5 x 0,85 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
connected load frequency: 230 V output: 1,2 KW taper diameter: 19mm mm turning speeds: 1000 - 3000 U/min roll surface width: max. 100 mm roll length: max. 120 mm weight: 2,8 kg range L-W-H: 430 x 280 x 100 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bore capacity in steel (diameter): 16 mm throat: 170 mm bore stroke: 50 mm : 16 mm spindle taper: MK2 spindle turning speed range: 50 - 2250 U/min : 320 mm : 145 mm table surface area: 500 x 140 mm connected load frequency: 230 V total power requirement: 0,5 kW weight of the machine ca.: 90 Kg dimensions of the machine ca.: 0,5 x 0,45 x 0,84 m Drilling and milling machine with - variable spindle speed - Digital depth display - Left / right switch - Cross support - swiveling spindle head - Feeds via hand crank - Tool case with content but without digital display The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Komptech Multistar L3 # 75144 Facilities Multistar L3 Trailer Multistar L3 EU Declaration of Conformity Connect Control cabinet 50Hz Diesel generator 80 kW T4f/Stage V Cleanfix - Fan Fine Screen Deck 10/25 S1 Coarse screen deck 60/90 Bunker Hydr.Foldable Dosing roller Hammer Standard Fine grain collection belt Medium grain discharge belt Air Classifier Medium Grain Preparation of the GK air classifier Trailer (3-axle) Switching from 3 to 2 fractions Slip-on shoe Condition: Servicemaintained Availability: by arrangement Warranty: The machine will be sold in the condition existing at the time of delivery. The seller assumes no liability for defects. We reserve the right to sell in advance, make changes and repairs.
sheet width: 1000 mm plate thickness: 5,0 mm distance between columns: 1070 mm diameter of upper rolls: 130 mm total power requirement: 4,0 KW weight of the machine ca.: 1,15 t dimensions of the machine ca.: 2,55 x 0,65 x 1,1 mm - Electrically adjustable rear roller - Electrically adjustable lower roll (material clamping) - Digital readout for rear roller movement - Digital readout for lower roll movement (material clamping) - Hardened rolls - Conical rolling - Swiveling top roll - Brake motor - Emergency stop - Documentation - 400V The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 1000 mm y-travel: 300 mm z-travel: 400 mm table-size: 1320 x 360 mm spindle taper ISO: 40 spindle turning speed range: 58 - 1800 U/min total power requirement: 4 kW weight of the machine ca.: 2,3 t dimensions of the machine ca.: 2,1 x 2,1 x 1,95 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
width of the strips: 75 mm band length: 2000 mm band speed: 37 m/sec total power requirement: 3 kW weight of the machine ca.: 0,105 t dimensions of the machine ca.: 1,2 x 0,5 x 1,0 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Komptech Multistar L3 Category: Star Screen Specification: Serial / reference number: 75070 Designation: Multistar L3 Performance: Weight: kg Emission class: Tier 4 Final / Stage V Equipment and description: Screen with 3 fractions – fine fraction (mm): 0/10... 25 Middle fraction (mm): 10... 25/60… 90; Coarse fraction (mm): > 90... 120 75 kW/A Diesel Generator Bunker volume: 7 m3 Feed height (mm): 3,450 / Feed length (mm): 3,750 Max. discharge height medium and fine fraction (mm): 3,500 / Max. discharge height coarse fraction (mm): 2,850 Weight approx. 21 tons / Transport length (mm): 11,500 / Transport width (mm): 2,250 / Transport height (mm): 4,000 Throughput depending on the type of material up to approx. 200 m3/h Availability: by arrangement Warranty: The machine will be sold in the condition existing at the time of delivery. The seller assumes no ...
width of the strips: 25 mm band length: 762 mm dimensions of grinding wheel: 125 mm Table tiltable up to: 45 Grad table surface area: 130 x 130 mm connected load frequency: 230 V total power requirement: 0,3 kW weight of the machine ca.: 9 Kg dimensions of the machine ca.: 650 x 360 x 400 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding range: 2 - 20 mm sharp cornered angle min./max.: 90 - 135 Grad connected load: 230 V weight of the machine ca.: 8,6 Kg dimensions of the machine ca.: 0,35 x 0,2 x 0,2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Inv. Num. : 9234 Type: TruLaser 1030 Producer: Trumpf Created: 2024 Parameters: Control system: SINUMERIK 840D SL Maximum power: 10 kW Work table length: 3000 mm Work table width: 1500 mm Maximum sheet thickness when cutting (stainless steel): 40 mm Maximum sheet thickness when cutting (aluminium): 30 mm Maximum sheet metal cutting thickness (steel): 35 mm Maximum sheet metal cutting thickness (copper/brass): 12 mm Feed length Z-axis: 115 mm Source: TruDisk 10 000 W Machine height: 2200 mm Machine length: 9300 mm Machine width: 4700 mm Machine weight: 5500 kg Equipment: Cross and longitudinal conveyors Pallet Changer
: 50 (500) mm : 45 (500) mm L-beam: 80 x 80 x 8 (800) mm T - beam - web outwards: 80 x 9 (800) mm Axis diameter: 60 mm work speed: 5,0 m/min Tool diameter: 195 mm total power requirement: 3 kW weight of the machine ca.: 1,0 t dimensions of the machine ca.: 1,2 x 0,9 x 1,2 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display - hardened special steel shafts - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable - Horizontal and vertical operation - Engine with braking device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Counting and banding machine ATS US 2000 FSB-DBN-T; State as is; should be installed by ATS Customer Service; suitable for processing banknotes; Rontech MF-360 RAV counting feeder; 1x Banderolier ATS US 2000 AD bandwidth 40mm and frame 260x260mm; 1x Banderolier ATS US 2000 AD Bandwidth 30mmund Frame 260x120mm; Turning unit installed. Count and banding machine ATS US 2000 FSB-DBN-T; condition as is; should be installed by the support of ATS; used for banknotes; count feeder Rontech MF-360 RAV; 1x banding machine ATS US 2000 AD with band width 40mm and frame 260x260mm; 1x banding machine ATS US 2000 AD with band width 30mm and frame 260x120mm; turning station.
width of the strips: 100 mm band length: 1220 mm band speed: 1140 m/min. : 0,62 x 0,4 x 0,35 cm total power requirement: 1,5 kW weight of the machine ca.: 0,04 t dimensions: 0,97 x 0,67 x 0,37 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
faceplate diameter: 3200 mm swing diameter: 3500 mm turning height: 2200 mm Control: Typ 840 D sl total power requirement: 51 kW weight of the machine ca.: 86 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 800 mm y-travel: 500 mm z-travel: mm Control: Heidenhain tool taper: SK 40 : 13,5 kw turning speeds: 3150 U/min total power requirement: kW weight of the machine ca.: 3 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Seidenader line for the visual inspection of vials, comprising a Seidenader DT1202 vial/bottle feeding turntable with a diameter of 1200 mm, 1 x 2 units. Seidenader V90-AVSB/30-LR + V90-AVSB/30-RL semi-automatic inspection machines for the visual inspection of cosmetic defects and particles in vials, etc., size range from 0.5 to 1000 ml, throughput of up to 150 objects per minute. The machine is used for the visual inspection of particles, glass defects and gross defects, cracks and hairline cracks. The machines are equipped with TYNDALL light from the top front for cap and glass defects (the light shines from above onto the caps of the containers; for lyophilisates, powders and emulsions, it also shines onto the product) and TYNDALL light from below at the front for non-clear liquids, emulsions, powders and lyophilisates (the light shines diagonally from below onto the base of the conta ...
clamping force: 700 kN injection volume: 103 cm³ screw diameter: 30 mm platen size: 432 x 310 mm closing stroke: 650 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
clamping force: -- kN injection volume: 230 cm³ screw diameter: 40 mm platen size: 475 x 475 mm Condition: used, Specification: Horizontal injection moulding machine, injection unit: - Screw diameter: 40 mm - Cylinder diameter: 40 mm - Spraying volume: 230 cm³. Clamping unit: - tie bar distance: 475 x 475 mm - Operating hours approx.: 30000 h - Air valve - Core pull - 12-way hot runner controller The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Komptech Multistar One Star screen with electric drive #6929 Facilities Multistar ONE EU Declaration of Conformity Feed hopper Anthology Machine documentation 5 inch touch panel Electric Hydraulic Pump HyDrive 2.0 MS ONE Doppstadt Siebdeck 60/90 Drive motors (2 pcs.) Fine grain discharge belt Oversize discharge belt Hook Lift axle Shunting drawbar Condition: Servicemaintained Availability: by arrangement Warranty: The machine will be sold in the condition existing at the time of delivery. The seller assumes no liability for defects. We reserve the right to sell in advance, make changes and repairs.
x-travel: 600 mm y-travel: 400 mm z-travel: 420 mm Control: Heidenhain Tnc table-size: 900 x 460 mm turning speeds: 4000 U/min total power requirement: kW weight of the machine ca.: 2,9 t dimensions of the machine ca.: 3 x 2 x 2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
clamping force: 4200 kN injection volume: 572 - 1716 cm³ screw diameter: 90 mm platen size: 1040 x 1040 mm closing stroke: 620 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
CNC lathe GILDEMEISTER CLX 350 V3 With control DMG MORI SLIMline Multi Touch Fanuc I series Year of manufacture: 2018 Turning diameter: 320 mm Travel in X: 242 mm Travel in Z: 540 mm Spindle bore: 65 mm Speed range: 20 – 5000 rpm With the following accessories: Slide protection with interior lighting 12-speed turret with 12 driven tool stations VDI 30 C Axis , Tailstock with Quill Programmable tailstock via M function Tool measurement in the work area Electronic handwheel Chip conveyor 3 jaw chuck hydraulic Schunk ROTA THW plus 0 210 mm Foot switch for jaw chuck adjustment Parts catcher Glass Scale in the X Axis Coolant device with high-pressure pump 12 bar Coolant spray gun Operating Instructions
cross-section width:: -- mm cross-section heigth:: -- mm feed:: -- mm speed of feed:: 0,4 - 20 m/min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cross-section width:: 85 mm cross-section heigth:: 25 - 40 mm feed:: 1 - 999,999,9 mm speed of feed:: 60 m/min cuts max.:: 100 - 120 Schnitte/m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cross-section width:: 5 Schläuche 3-5 mm cross-section heigth:: 3 - 20 mm feed:: 1,5 - 50 mm Condition: used, very good condition only approx. 1 year in production Specification: circular knife cutting machine for slices and rings - small cutting machine with high-speed rotating circular knife - feed and knife movement, pneumatic - Tube or strand diameter min.: 3 mm - Tube or strand diameter min.: 20 mm - Feed (ring or strand length): 1.5 - 50 mm - Output depending on material max.: 60 strokes/min - Optionally, the following can be cut 5 tubes or strands: diameter 3 mm to 5 mm 4 tubes or strands: diameter 5 mm to 7 mm 3 hoses or strands: diameter 7 mm to 12 mm 2 hoses or strands: diameter 12 mm to 15 mm 1 hose or string: diameter 15 mm to 20 mm - Power requirement approx.: 0.37 kW - Air supply min.: ...
max. wheel diameter: 275 mm gear width: 55 mm max. module: 6 min. module: 1,5 control: Sinumerik 840C tooth width: 5,5 mm spiral angle: 0/60 ° max. number of teeth: 120 min. number of teeth: 5 transmission ratio max.: 1:10 transmission ratio min.: 1:1 spindle speeds: max. 110 mm blade head turning speeds: 20-110 1/min total power requirement: 100 kW weight of the machine ca.: 16700 kg dimensions of the machine ca.: 5200x2300x2400 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
The Inauen VC999 K12 is a professional double-chamber vacuum packaging machine designed for high-capacity food packaging operations. Its dual-chamber configuration allows continuous workflow and increased productivity compared to conventional vacuum sealers. Equipped with a powerful 220 m³/h vacuum pump, digital controls, and a three-nozzle suction system, it provides flexible packaging options for a wide range of products and package sizes. The stainless steel construction ensures durability, easy maintenance, and excellent hygiene standards. Technical Specifications: Manufacturer: Inauen Model: VC999 K12 Type: Double Chamber Vacuum Packaging Machine Material: Stainless Steel Power Supply: 400 V / 50 Hz / 3N Power Rating: 9 kW Vacuum Pump Capacity: 220 m³/h Number of Suction Nozzles: 3 Operating Pressure: 5 – 8 bar Chamber Dimensions: 1045 x 210 x 605 mm Machine Dimensio ...
Ref. 531 Eurofold 235 Model: 435.122 Serial: 20287 05 Year of construction approx. 2007 4 pockets Max. sheet format: 350 x 650 mm Paper Weight: 40-240g/m² Folding capacity up to 30,000 A4/hour Shed display Counters/Lots Counters With cutting and perforating wheel Instruction manual and spare parts list Condition: Functional / Mint Rolls Ref. 531 Eurofold 235 Model: 435.122 Serial: 20287 05 Year of manufacture: approx. 2007 4 pockets Max. sheet size: 350 x 650 mm Paper weight: 40–240 g/m² Folding capacity up to 30,000 A4 sheets/hour Staggered delivery Counter/batch counter With cut and perforating wheel Operating instructions and spare parts list Condition: Fully functional / Rollers in mint condition
: 0 bore depth: 10000 mm number of spindles: 0 Control: Siemens Simatic Touch SPS swing over bed: 1050 mm swing diameter over bed slide: 1600 mm boring diameter: 50 - 310 mm centre height: 800 mm speeds:: 2,5 - 400 total power requirement: 74 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
plate thickness: siehe TD mm pressure: siehe TD t total power requirement: 4 kW weight of the machine ca.: 0,950 t dimensions of the machine ca.: 900 x 1050 x 1300mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Used horizontal automatic sachet filling machine made by Miflex model SP-200. New 2016. The machine is designed for the automatic formation of flat V-shaped sachets as well as stand-up Doypack sachets. It packages loose, granulated, liquid and semi-liquid materials, e.g. gel. The machine is equipped with a volumetric dosing unit and a dosing unit for liquid and semi-liquid products Packaging materials include: polyethylene-coated paper + aluminium, metallised film, laminated films, etc. Packaging material width – max. 500 mm Pouch height: 80–180 mm Machine output when operating on two lanes: 70 units/min The Sp-200 machine is built on a self-supporting frame with safety guards. All components can be easily dismantled for cleaning and maintenance.
bore capacity in steel (diameter): 23 / 28 mm throat: 260 mm bore stroke: 120 mm tool taper: MK 3 table-size: 500 x 350 mm column diameter: 100 mm total power requirement: 1,3 kW weight of the machine ca.: 400 kg dimensions of the machine ca.: 800 x 600 x 1750 mm Defective feed! Right-left rotation stepless speed adjustment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
screw size: 98 mm injection shot weight in Polysterol: unbkt. g/PS closing pressure: 8600 kN total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
maximum number of results exceeded
please refine your search
