t slot used for sale

Manufacturer: Trepel Hebebühne, Type: EH40/13/1, Year: 1996, Lifting power kg: 3500, Length mm: 5000, Width mm: 1100, Year :1996

Manufacturer: Trepel, Type: EN 10/10/0, Year: 2002, Lifting power kg: 1000, Length mm: ca 1400 , Width mm: ca 800, built-on roller conveyor: no, Year :2002

Various ZKG ZKGs fermentation tanks storage tanks pressure tanks beer, jacket cooling, cooling jacket, year of construction 2004, net volume approx. 45 hl, 4500 liters, 1.5 bar. Various Numbers of CCTs, Storage Tanks, BBTs, Bright Beer Tanks, Cooling jacket, Year: 2004, Net Volume approx. 45 hl, 4500 liters, 1.5 bar.

Oil-Insulated Power Transformers for Sale Transformer 1 - Manufacturer: ELIN - Model: TDQ-164A11S9K-99 - Power Rating: 15 MVA - High Voltage: - 121.5 kV (Position 0) - 118.463 kV (Position -1) - 115.425 kV (Position -2) - Low Voltage: 6.3 kV - Current Rating: - High Voltage: 71.3 A (Position 0), 73.1 A (Position -1), 75.05 A (Position -2) - Low Voltage: 1375 A - Frequency: 50 Hz - Cooling: ONAN - Year of Manufacture: 1994 - Status: Out of service since 2022 - Notable Condition: Relatively high CO levels (due to oxidation); insufficient oil inhibitor content. Oil treatment with inhibitor replenishment recommended. Find more here - / Contact us at -

Oil-Insulated Power Transformers for Sale Manufacturer: ELIN Model: TDY-164A11S9K-99 Power Rating: 15 MVA High Voltage: - 121.5 kV (Position 0) - 118.463 kV (Position -1) - 115.425 kV (Position -2) Low Voltage: 6.3 kV Current Rating: - High Voltage: 71.3 A (Position 0), 73.1 A (Position -1), 75.05 A (Position -2) - Low Voltage: 1375 A Frequency: 50 Hz Cooling: ONAN Year of Manufacture: 1993 Status: In operation until 2025 Notable Condition: High CO levels, insufficient oil inhibitor content. Oil treatment with inhibitor replenishment recommended. Find more here - / Contact us at -

Oil-Insulated Power Transformers for Sale Manufacturer: Brown Boveri Model: TRFKa 1350/30 Power Rating: 1350 kVA High Voltage: - 26.25 kV (Middle position) - 27.56 kV (Position 1) - 24.93 kV (Position 5) Low Voltage: 6.3 kV Current Rating: - High Voltage: 29.7 A (Middle position) - Low Voltage: 124 A Frequency: 50 Hz Cooling: ONAN Year of Manufacture: 1972 Status: In operation until March 2025 Notable Condition: High CO levels and water content; oil drying and treatment recommended. Find more here - / Contact us at -

Slot counter spigot outside inside

Tool used 320x24x58, n 5600 - 2300 HW, BLAA further data on request

Key data: 2000 mm, 2400 mm, 1500 mm

Stock number: 3988 CNC CAROUSEL LATHE Manufacturer: ALEX TECH VIPER, Type: VTL 20/24 M Machines NO.: 7640901011, Year of manufacture: 2008 Specifications: Face plate diameter 2000 mm Large turning diameter 2400 mm Face plate speeds ( ) 1-73 / 1-200 2 step rpm Large workpiece height 1500 mm Gr. face plate load 20000 kg X- Movement 1800 mm Y- Movement ( Cross Beam ) 800 mm - 5 Sep each 200 mm Z- Movement 1000 mm C-Axis 0.001 degree Ram size 230 x 230 Power 11/15 Driven tool revolutions 30-2000 rpm Tool Changer 18 (9 Turning 9 Milling ) ISO 50 Stations Main motor 45 Voltage 400 volts Einständer. CNC Control: Fanuc Oi-TD Spindle Hours 10453 Accessories: Chip conveyance. New 2025 Cooling water system. Various accessories. Cooling in the Spindle Delivery time August 2025  ...

BODE TT60 welding positioner is used for the manipulation of a workpiece with a maximum weight of 3000 kg during the welding process. The device makes it possible to work in the optimum position, thus contributing to improved welding quality. The versatility combined with perfectly thought-out design solutions make the BODE welding positioner guarantee safe handling and trouble-free operation for many years of use. Technical specifications of the BODE TT60 welding turntable - maximum workpiece weight: 3000 kg - table diameter: 2800 mm

Lg.Nr. 25072 Specifications: - Drilling capacity in steel ST 60 40 mm - Drilling spindle holder MK 4 - Drilling spindle stroke 150 mm - Drilling spindle speeds infinitely variable rpm - Projection 350 mm - Max. distance from drilling spindle to table 580 mm - Table with 2 T-slots 600 x 450 mm - Height adjustable via rack with hand crank - Table left + right tiltable - Drive 400 V / 3 kW - Space requirement approx. W 700 x H 1950 x D 950 mm - Weight approx. 650 kg -with: - Machine vise - Keyless chuck 1-13 mm -Lighting

Key data: 65 mm

CNC Turning and Milling Center CNC lathe used CNC universal lathe Manufacturer: Traub Type: TNA 300 Year of Make: 1996 Spindle ø 65mm Tailstock Powered tools Conveyor Control TX8H FlexIPS Collet chuck with collets from 5mm to 65mm Three-jaw chuck Various tool holders fixed, rotating and angle-rotating Etc... incl. bar loading magazine Traub DNH 61 3000, year of construction 1996 incl. many accessories! Location of the machine: Nahe 93047 Regensburg The machine can be viewed on site. It is still energized and works perfectly. We would love to hear from you.

Turning diameter 350 mm Turning lenght 550 mm Spindle speed 5000 rpm Bar work diameter 65 mm Controller MAZATROL smart

Bar diameter 26 mm 12 live tools Turning lenght 180 mm Controller FANUC 16i-TB Spindle speed 12.000 rpm With barfeeder

7 axes Max. spindle passage: Ø 16 mm Max. headstock stroke: 205 mm MAIN SPINDLE Spindle speed: 10000 1/min Spindle drive power: 3.7 kW Minimum C-axis resolution : 0.001 [degrees] SUB-SPINDLE - Max. rod end Ø: 16 mm - Spindle speed : 9000 1/min - Minimum resolution C-axis : 0.001 [degrees] TOOLS 5x Turning tool holder on linear slide 4x drilling unit incl. drilling holders (front/rear) 3x driven tools for transverse machining on linear slides 4x tools incl. drill holders for reverse side machining Driven Tools Speed : 7500 1/min Conveyor Bar Feeder FMB minimag 18/3200

Key data: 300 °C, 2 kW, 144000 W

used oil temperature control unit with 5.5 kW pump max. pre-fuse 80 A electr. Connection 35 kW little used

ZM testing equipment

CNC Model: Fanuc - CNC Version: 18i - TB - Main Spindle Nose: ASA 8 - Main Spindle Power: 26Kw Main spindle bar passage: 81mm - Turning diameter: 300mm - Turning length: 350mm - Main spindle speed: 3500 Number of tool turrets: 2 Number of tool positions for the first turret: 12 Number of Motorized First Turret: 12 First turret X-axis travel: 255mm Y-axis travel first turret: +- 60mm First turret Z-axis travel: 800mm Number of second turret tool positions: 12 Number of motorized second turret: 12 Second turret X-axis travel: 190mm Second turret Z-axis travel: 900mm Fast feeds for linear axes X Y Z: 24m/min Sub-spindle: yes Spindle nose: ASA 8 Number of counter-spindle speeds: 3500 Counter spindle power: 26Kw Bar Passage: 81mm Z stroke sub-spindle : 810mm Chip conveyor: belt Presetting: yes Machine equipment: Machine supplied wit ...

CNC Model: Fanuc Main spindle power: 3.7Kw Main spindle bar passage: 20mm Headstock Stroke (Z1): 210mm Number of main spindle speeds: 8000 Number of linear axes: 6 Number of fixed tool slots for tool plate: 7 Number of live tool slots for tool plate: 3 Fast feeds linear axes X Y Z: 20m/min Sub-spindle: yes Number of counter-spindle speeds: 7000 Bar Passage: 20mm Counter-spindle motorized face tools: 4 Number of motorized rear tools: 8 Refrigerant used: neat oil Model and brand bar loader: Iemca Boss 432 :::D DIMENSIONS AND WEIGHT::: Length: 2150mm Width: 1450mm Height: 1825mm Weight: 2800Kg

Tunnel conveyor belt, conveying height approx. 190cm, total length 380cm, height adjustable, current width approx. 105mm. 380V motor, little used. (there are two tapes)

Telemecanique LC1 FF 43 + LA1 F 221

Manifold GEA TUCHENHAGEN Mixproof-valves - Flushing - Balanced Valve top type: TM15N2B0M/66 DN25 NL = 8x DN25 KWIK = 3x DN 65 = 2x DN 80 = 27x Please contact u for more information

MAZAK QUICK TURN NEXUS 100MS CNC lathe was built in 2005 in Japan by YAMAZAKI MAZAK CORP. The machine, designed for precision machining of workpieces with a maximum diameter of 280 mm, is distinguished by the use of reliable components with excellent technical parameters, such as two spindles (main spindle and sub-spindle) and a 12-position turret. The machining process is performed inside a large, fully illuminated workspace by means of a powerful spindle with an integrated motor design that minimises vibrations at high speeds. This is all complemented by an intelligent CNC control that simplifies daily work by allowing even the most advanced machining programmes to be created in just a few steps. The MAZAK QTN-100MS CNC turning center weighs 4100 kg. Technical specifications of the MAZAK QUICK TURN NEXUS 100MS metal lathe - CNC control: MAZATROL 640T NEXUS - maximum turning diamet ...

1. Qty. 1 Second-hand slab gas fired pit type furnace Manufacturer: Tehnika Set Type: Gas heated (2 Zones) Built: 2001 Stopped: 2019 Power: 110kW Number of heating units: 8 Dim.: 2622 5084 x 6294 mm – H x W x L Inner dimension per zone: LxWxH – 380026001635 mm Load weight max. / 2 zones: 42.000 kg Max. Slab number per zone: 5 Slab length: 3000 mm Voltage supply: 380 V, 50 Hz Compressed air: 5 bar Max. Temp.: 630 °C

bar capacity 90 mm - 2x12 driven positions turrets - Y axis in upper turret - tail stock - very very well equipped ( 36 driven + 39 fixed tool holders - 30 collets etc.etc.) - Lns Sprint S2 barfeed with front magazine - Siemens 840D Power Line Control - IN PERFECT CONDITION

Star SR 32 J III Type B Year of Make: 2022 Machine is not yet for sale, but you are welcome to send us your offer today.

Damping tunnel for inserted/pinched shafts

Tatham Twin shaft paddle mixer Serial: CO1040 Stainless, 1200Kg twin shaft paddle mixer, New motors, new gearbox, new chains, with stainless holding hopper at base

Used-refurbished machine 350 Litre tank capacity Belt drive with toothed belt TC 20/40 programmable control Vacuum pump

Standing GRP tanks, polyester tanks from the company Staffelstein, with flat bottom with slope Volume: 100,000 L Dimensions: Ø 3.40 × 11.03 m high Call us or write to us! We would be happy to make you a non-binding offer! Scholten Tanks GmbH Brüsseler Str. 1 48455 Bad Bentheim/Gildehaus Phone: 05924 255 485

Standing steel tanks with inner coating, insulated, standing, with feet can be used, for example, as a buffer tank or as a rainwater tank Volume: 58,000 L Dimensions: Ø 3.20 m × 8.50 m high Call us or write to us! We would be happy to make you a non-binding offer! Scholten Tanks GmbH Brüsseler Str. 1 48455 Bad Bentheim/Gildehaus Phone: 05924 255 485

Standing steel tanks with inner coating, standing, with feet can be used as a rainwater tank, for example Volume: 58,000 L Dimensions: Ø 3.00 m × 8.50 m high Call us or write to us! We would be happy to make you a non-binding offer! Scholten Tanks GmbH Brüsseler Str. 1 48455 Bad Bentheim/Gildehaus Phone: 05924 255 485

Standing steel tanks with inner coating, standing, with feet can be used as a rainwater tank, for example Volume: 51,000 L Dimensions: Ø 3.00 m × 7.80 m high Call us or write to us! We would be happy to make you a non-binding offer! Scholten Tanks GmbH Brüsseler Str. 1 48455 Bad Bentheim/Gildehaus Phone: 05924 255 485

Standing steel tanks with inner coating, standing, with feet can be used as a rainwater tank, for example Volume: 58,000 L Dimensions: Ø 3.00 m × 8.50 m high Call us or write to us! We would be happy to make you a non-binding offer! Scholten Tanks GmbH Brüsseler Str. 1 48455 Bad Bentheim/Gildehaus Phone: 05924 255 485

Demag 5 ton x 15 100 mm Kind of: overhead travelling crane Capacity: 5 ton Span: 15 100 mm Radiocontrol: no radio control Numbre of riggers : double rigger

Pinomatic cross conveyor for a planing and sawing line Year of construction 2001 Manufacturer Pinomtatic OY Type POS 9+10 S/N P1033 motorised cross conveyor with 7 chain hoists length of the arms: : 6000mm Width of the cross conveyor up to 4000mm ( variable adjustable ) Height: 900mm 6 chain hoists fixed mounted 1 chain hoist can be variably adjusted Voltage 230/ 400VAC

Demag 6,3 ton x 15 100 mm Kind of: overhead travelling crane Capacity: 6,3 ton Span: 15 100 mm Radiocontrol: no radio control Numbre of riggers : double rigger

Demag 6,3 ton x 11 410 mm Kind of: overhead travelling crane Capacity: 6,3 ton Span: 11 410 mm Radiocontrol: no radio control Numbre of riggers : double rigger

Shimadzu TOC VCPH with SSM-5000A solids module and ASI-V autosampler as liquid propene encoder, software

Demag Mannesmann 6,3 ton x 11 410 mm Kind of: overhead travelling crane Capacity: 6,3 ton Span: 11 410 mm Tackle speed: 1 & 6,3 m/min Rotationspeed: 5 & 20 m/min Displacementspeed: 10 & 40 m/min Radiocontrol: no radio control Numbre of riggers : double rigger

Demag 6,3 ton x 15 093 mm Kind of: overhead travelling crane Capacity: 6,3 ton Span: 15 093 mm Tackle speed: 1 & 6,3 m/min Rotationspeed: 5 & 20 m/min Displacementspeed: 10 & 40 m/min Radiocontrol: no radio control Numbre of riggers : double rigger

Tsugami BU20 Swiss-type lathe :::TECHNICAL SPECIFICATIONS::: CNC Model: Fanuc CNC Version: 16i - TB Main spindle power: 3.7Kw Main spindle bar passage: 20mm Headstock Stroke (Z1): 170mm Number of main spindle speeds: 8000 Number of linear axes: 7 Number of fixed tool slots for tool plate: 4 Number of live tool slots for tool plate: 3 Sub-spindle: yes Number of counter-spindle revolutions: 8000 Bar Passage: 20mm Number of fixed rear tools: 6 + 6 Refrigerant used: neat oil Chip conveyor: belt Machine equipment: the machine is supplied without bar loader :::D DIMENSIONS AND WEIGHT::: Length: 2712mm Width: 1401mm Height: 1728mm Weight: 3500Kg

Circumferential diameter over bed ... 500mm Turning length ... 2000mm Max. workpiece weight ... 300kg Circumferential diameter via support ... 270mm Spindle bore ... 52mm Spindle speed ... 22-2000 rpm Main engine power ... 5.5kW L x W x H ... 3640x1100x1580mm Machine weight ... 1940kg The machine is in good condition, possible to test under power.

Connected load: 0.32 kW Weight: 125 kg Manufacturer: Tassold GmbH Model: Rotary Table Year of Make: 2022 Connected load: 0.32 kW Weight: 125 kg Dimensions of the rotary table: Length: 1,800 mm Width: 1,000 mm Height: 1,200 mm Diameter turntable: 1,000 mm Dimensions of the infeed belt: Length: 1,000 mm Width: 600 mm

Key data: 100 °C, 8 kW, 30 W

HB-Therm HB-100Z1 temperature control unit with water medium for a maximum temperature of 100 °C. Heating 8 kW, cooling 30 kW, pump 1 kW, 60 l/min, 60 m. In good condition, ready for use. Please also note our large selection of other used plastic processing machines. All our machines can be viewed on site via video and tested in person.

Inline Tray Sealer Make: MPE Model: I0 Built 2017 Stainless steel Mould set: D2: 195 X 154MM 16 Cycles min, Gas facility

Toyota BT Quick Lift pallet truck 2300kg 1150 mm RA2231 Manufacturer: Toyota Fork length: 1150 mm Fork width: 156 mm Carrying surface width: 520 mm Maximum load capacity: 2300 kg Lifting range: 85 - 200 mm With quick lift, 2x pumping is sufficient to be off the ground, with a maximum load of 150 kg Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

Tube bending machine - mandrel bending machine TRACTO-TECHNIK Type Transfluid DB 2060 KSerien. No. 70173 Year of construction 2004Bending capacity (steel) max. 76.1 x 3.0 mmBending capacity (stainless steel) max. 76.1 x 1.65 mmBending tool max. 70 x 2 mm (for stainless steel)Pipe slide length 4572 mm (4300mm)Bending radius max. 150 mmBending direction clockwise (right)Bending angle max. 190Bending head speed at 90 8 sec. Hydraulic operating pressure 200 barEngine power 3 KWnet connection 400 Volt, 50 Hz, 15

A simultaneous turning center Spinner with three turrets and extensive accessories, spare parts and tools is available. Travel X1/X2/X3: 180mm, travel Y1/Y2: +/-45mm, travel Z1/Z3: 704mm, travel Z2/E2: 620mm/720mm, rapid traverse X/Y/Z: 30m/min, acceleration: 0.5g. Spindle 1: Speed: 5000rpm, nose: A6, bore: 65mm, chuck diameter: 210mm, power: 18kW, torque: 115Nm. Spindle 2: Speed: 700rpm, nose diameter: 110mm, bore: 42mm, max. chuck diameter: 140mm, max. chuck jaw weight: 1.25kg, power: 16.6kW, torque: 100Nm. Turret 1/2/3: Turret stations: 3x12, speed: 8000rpm, tool holder: BMT 45, power: 4.3kW, torque: 13.6Nm. Machine dimensions X/Y/Z: approx. 2880mm/2130mm/1990mm, weight: approx. 7500kg, operating hours: 27102h, control: Fanuc 31i. Including loading magazine Top Automazioni, cooling/high pressure system with 80bar, chip conveyor, fire extinguishing system, a comprehensive tool package  ...

A Thermconcept high-temperature tube furnace is available. T. max.: 1700°C, heated length: 200mm, tube diameter/length: 60mm/600mm, power: 3.3kW, dimensions X/Y/Z: 460mm/530mm/830mm. Documentation available.