129,251 used machines on RESALE, but how to find them? Machine Search
Styrofoam briquetting press With an innovative technology, the press compacts bulky foam waste from EPS (polystyrene®) into easy-to-handle blocks in an extremely economical way. The extreme volume reduction achieved in this way in a ratio of up to 40:1 not only saves transport and disposal costs to a considerable extent, the blocks produced can also be recycled as raw materials and contribute to a quick amortization. - Long service life due to robustly designed drive technology - Efficient process due to fully automatic pressing pressure control, with predetermined breaking point function and individual block length - Hours of operation without overheating and fusion due to optional water-cooled pressure channel - Convenient, fully automatic operation due to state-of-the-art control - High cost-effectiveness due to low operating and maintenance costs - Simplest commission ...
Manufacturer: Busch Type: Mink MI 1502 BP Engine: 18.5 KW ; DS 400V Status: Used, partial performance: 6 months Volume flow: 500 m3/h compression pressure: +1.2 bar Accessory: additional suction filter (changed) ; Operating manual delivery time: approx. 1-2 Where.; ready for use
Styrofoam briquetting press With an innovative technology, the press compacts bulky foam waste from EPS (polystyrene®) into easy-to-handle blocks in an extremely economical way. The extreme volume reduction achieved in this way in a ratio of up to 40:1 not only saves transport and disposal costs to a considerable extent, the blocks produced can also be recycled as raw materials and contribute to a quick amortization. - Long service life due to robustly designed drive technology - Efficient process due to fully automatic pressing pressure control, with predetermined breaking point function and individual block length - Hours of operation without overheating and fusion due to optional water-cooled pressure channel - Convenient, fully automatic operation due to state-of-the-art control - High cost-effectiveness due to low operating and maintenance costs - Simplest commission ...
l 45 kw POWER 680 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 45 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw
Pressure: 65 tons -Stroke: 140 mm -Table size: 720 x 600 mm -Plunger surface: 500 x 300 mm -Tappet adjustment: 80 mm -Strokes: 20-40 per min. -. Weight: 6000 kg -Dimensions (L x W x H): height 3.1 m -Clamping hole ø 60 x 80 mm More info on request
CNC – controlled frame gluing press for automatic gluing of all frame constructions with dowel connection – tine connection – 45° miter connection, automatic centering of the press plates and the upper press beam. The frame presses are available in the following sizes – pressing area 3,000 x 1,700 mm – 3,000 x 2,000 mm and 3,500 x 2,500 mm. Two vertical press cylinders – pressing force per cylinder 7 tons (optional four vertical press cylinders). Two horizontal press cylinders, stroke range 150 mm - pressing force per cylinder 3 tons. Maximum tread depth 130 mm (larger tread depths on request). CNC control from SIEMENS® with touch screen for calling up three automatic pressing cycles, 99 compression programs can be stored per pressing cycle. Among other things, the following parameters can be programmed: frame size, frame profile structure, pressing time, pr ...
Gluing stand VHS with motor hydraulics for gluing all frame constructions with dowel connection – tine connection – 45° miter connection. The motor-hydraulic gluing stands VHS are available in the following sizes: Maximum grouting range 2,500 x 1,800 mm 2,500 x 2,100 mm 3,000 x 1,800 mm 3,000 x 2,100 mm 3,500 x 2,100 mm Three vertical press cylinders with a stroke range of 120 mm and a pressing force of 2 tons each. Two horizontal press cylinders with a stroke range of 120 mm and a pressing force of 2 tons each (optionally, the gluing stands can of course be supplied with more press cylinders). Drive power 0.75 to 1.25 kW.
Tech. Data Nominal press force 1000 kN at maximum stroke adjustment - commute 6.5 mm 1250 kN at maximum stroke adjustment - commute 3.5 mm Strokes with endurance 125/83/63 Hube/min Usable stroke rate 50 50 38 / min. Throat depth 320 mm, clamp 380 mm Stroke adjustment 10-120 mm, Stosselverstellung 80 mm Stosselflaeche 800 x 320 mm, recording journal 50 / 85 Tabletop table top hole, 900 x 630 mm 230 mm, Durchfalloch in the table 300 / 400 x 250 mm Drive - 7,5 / 5,5 kW Bulk 1350 x 2080 x 2780 mm, Btto 8900 kg
HACO ERM 30175 CNC press brake built in Belgium in 1999, performs precise bending of workpieces with a maximum length of 3100 mm. The robust, stable construction of the machine, together with a high press force of up to 175 tonnes, guarantee excellent machining results. The press is equipped with operator conveniences such as a pedal for foot control and a HACO bc40 GRAPHIC CNC control located on the arm. The total weight of the machine is 10 tonnes. Technical data of the HACO ERM 30175 press - CNC controller: HACO bc40 GRAPHIC - maximum press force: 175 t - maximum workpiece length: 3100 mm - bending speed: 8 mm/s - approach speed: 100 mm/s - return speed: 80 mm/s - distance between carcase walls: 2600 mm - reach: 300 mm - working stroke: 200 mm - safety distance: 300 mm - pedal for foot control - main motor power: 15 kW - waiting time: 75 ms - maximum pressure: 255 bar ...
Roll press / dough dividing and warp knitting machine / Klievmaschine Machine Mechanics completely overhauled & repainted by the expert New installation of the entire electrical system, according to the latest standards 6 months warranty Properties: + Stationary machine, very robust & stable construction + Machine is set in motion by switch-on lever, one-hand operation + Cleaning position electric, to the rear, with switch + even division of the dough, excellent rounding of the dough pieces + equipped with active cut-off, for square dough pieces + Partial knife / cutter head has been overhauled / recoated + completely disassembled, mechanically overhauled, repainted + New installation of the entire electrical system, according to the latest standards + Transmission parts run constantly in an oil bath + complete overhaul in Babenhausen, according to German quality stand ...
various hand spindle presses small More: Foot pendulum press Jantsch
Printing capacity max. 300 t, table 1500 x 1000 mm, stroke max. 500 mm
used cabinet press Manufacturer: Maschinenfabrik Bermatingen GmbH & Co. Type: DIXI 30 S Year of construction: 2009 Serial No.: 109138 specifications: Pressing force: 30 t Filling opening: 1,200 x 670 mm (W x H) Height from the ground: approx. 940 mm Split egg filling opening: 1,070 x 260 mm Height from the ground: 1,310 mm Bale size: 1,200 x 800 x 800 - 1,100 mm Bale weight: up to 270 - 360 kg Drive power: 7.5 kW Cycle time: approx. 29 sec. Pressing time: approx. 14 sec. Binding: 4-fold - vertical with poly strap Machine dimensions: 1,600 x 1,300 x 3,170 mm (W x D x H) Machine weight: 2,180 kg Transport height: 2,240 mm (Subject to errors in the technical data)
Cordmasspress built 1970 diverse thorns All data without information
Capacity , ton: 800 Stroke, mm: 320 Strokes/min: 20 Shut height, mm: 900 Bed to ram adjustment stroke, mm: 320 Bed dimensions, mm: 2500x1600 Main drive motor power, kW: 75 Overall dimensions, mm: 4220x3500x8356 Weight, ton: 96,6
Te Coop: Danfoss Druk druk transmitter MBS 3000 0-6 bar
Te Coop: Labom Druk transmitter CE 1110 Druk 0-25 bar
• 120 tons total pressing force • Pressing area 3,000 x 1,350 mm • With patented, thermostable electric heating plates with automatic temperature control system • Connected load of the heating plates with economy circuit 10.6 kW • Connected load of the hydraulics 2.2 kW • in 6-cylinder version Ø 85 mm • Lockable main switch • Push-button control • Stop button • Safety ripcord, safety edge • Timer with automatic opening and acoustic signal • Stroke = opening 400 mm • Infinitely adjustable stroke limitation • 2-stage hydraulics with automatic pressure follow-up • Compact hydraulic power unit mounted maintenance-free in the oil tank • Teflon bronze guides in the cylinders • Hard chrome-plated steel pistons • Heavy rack and pinion compensation for synchronous table movement • fully open on four sides • Economy circuit installed as s ...
Frame press Hess economic hydraulic 3600 x 2250 mm L x W x H: 400 x 100 x 270 cm Weight approx. 1100 kg year 1987 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Baling press cardboard foil MF100 | 6 t pressing force The MF100 balers are ideal for pressing cardboard, paper, film, clothing and other materials. Volume reduction through compaction of up to 90%. The press is user-friendly with a large filling volume. The automatic bale ejector helps to remove the bales from the baler without any problems. Characteristics: Bale weight of up to 100kg Ideal for use with medium material volumes Fully automatic bale ejection Powerful cylinder for uniform material compaction Hold-down device to reduce material springback CE certified Made in Europe Specifications: Pressing force: 6 t Motor: 1.5 kW 13 Amp Power supply: 220-230 V (1 phase) Machine dimensions (H x W x D): 2371 x 1388 x 1046 mm Transport height: 1876 mm Machine weight: 632 kg Cycle time: 28 seconds Noise level: 65 decibels Bale: Ba ...
Te Koop: Samson for Type: 3804 Druk: 0.016 - 0.4 bar maximum druk 0.76 bar. Prijs is incl. BTW
Hydraulic press brake. Working length: 3.000mm. Pressing force: 200Tn. Back gauge.
The BTS-1100 Bin Compactor is ideal for material compacting in your 1100 Ltr. garbage and recycling wheelie bins. Large bulky rubbish, but also cardboard and recyclable materials can be compacted easily and safe to a minimum of its size. By compacting these waste and recyclable materials you achieve a volume reduction of up to 80%, a significant saving on your disposal costs and you also create a safe and clean working environment. Pressing force: 3.5 Ton Compaction: up to 80 % (material depending) Machine size: 2120 H x 1160 W x 1150 D mm Machine weight: 270 kg Transport height: 1594 mm Cycle times: 20 seconds Motor: 1.5 kW 13 Amp Power supply: 220 - 240 V (1 phase) Noise level: 68 dB User-friendly and safe two hand lever control Optimum utilization of garbage bins Reduces the number of waste bins No more climbing into wheelie bins Reduces frequency of ...
Revised and repainted. The images are sample photos of similar machines and are intended to show the execution and quality of the revision. All wear parts are replaced. Filter cloths new. 1 year warranty on the filter press, excluding wear parts. Panel size: 630 x 630 mm Dimensions: approx. 2000 x 1100 x 1500 mm Chamber depth: 25 mm Capacity: 210 litres Operating pressure: 12 / 15 bar Turbidity inlet: flange 2", central Number of plates: 25 plates Material sheets: Polypropylene Material cloths: PP 5009 (white) Design: open filtration Closing pressure: max. 385 bar Painting: primed and painted in RAL 5010, filter trough + drip tray in plastic. Engine hydraulics with single-acting cylinder. Optional double-acting cylinder that retracts the heavy pressure plates. With the single-acting cylinder, the operator has to push the pressure plates back by hand. Optional: fill ...
High pressure cleaner, Cold water high pressure cleaner Manufacturer: Karcher Type: HD 700 Year of construction 1998 maximum pressure: 140 bar 9.5 L / min Drive: electric With hose package All information without guarantee
Transfer press KRUPP PST-A 160 built in 1980. Technical data of the KRUPP PST-A 160 press: - nominal pressure: 160 tons - cutting force grade 1: 400 KN - force between stands: 1200 KN - number of working steps including cutting stage: 11 - distance between stands: 200 mm - slider stroke: 210 mm - drawing depth: 70 mm - range of jumps, infinitely adjustable: 15-75 / min. - production range of jumps with repeatability of its setting: 25-75 / min. - number of actuation movements: 15-25 / min. - a usable work resource for a jump in the range of 25-75 strokes per minute. : 20,000 J - maximum load on a single step: 500 KN - maximum load of a single step using inserts: 630 KN - maximum width of the tape: approx. 340 mm - maximum diameter of the cut: 120 mm - minimum diameter of the pattern: 30 mm - distance between stands: 2450 mm - height of tool building at the lower posi ...
Rotary vane vacuum & compressor - dry running Manufacturer: Becker Type: DVT 3.140 and DVT 3.100 Engine: 400V DS Suction power: 100-140 m ³/h Discharge pressure / vacuum: Optional +-0.5 bar / +-1 bar / +-1.5 bar Status: Demo Warranty: 12 months; ready for operation
with 32 filling valves, 8head crowner and 8head aluminium screw capper with Siemens S7 control capacity: approx. 8,000 bottles/h in 500 ml bottles
Revised and repainted. The images are sample photos of similar machines and are intended to show the execution and quality of the revision. All wear parts are replaced. Filter cloths new. 1 year warranty on the filter press, excluding wear parts. Panel size: 630 x 630 mm Dimensions: approx. 2900 x 1100 x 1500 mm Chamber depth: 25 mm Capacity: 312 litres Operating pressure: 12 / 15 bar Turbidity inlet: flange 2", central Number of plates: 40 plates Material sheets: Polypropylene Material cloths: PP 5009 (white) Design: open filtration Closing pressure: max. 385 bar Painting: primed and painted in RAL 5010, filter trough + drip tray in plastic, Engine hydraulics with single-acting cylinder. Optional double-acting cylinder that retracts the heavy pressure plates. With the single-acting cylinder, the operator has to push the pressure plates back by hand. Optional: fill ...
Manufacturer: Bush type: mink MI 1502 BP Motor: 18,5 KW; DS 400V status: used, without Warranty: 6 months Flow rate: 500 m ³/h discharge pressure: + 1,2 bar Accessories: additional intake filter (changed); Manual delivery time: approx. 1-2 where.; ready for operation
GS12 - used approx. 26 m³ / 26,000 litres steel tank, gravel filter, pressure tank, water cistern. The container is used and in good condition. capacity: 26.2 m³ / 26,200 litres material: steel tank, pressure tank 6 bar outer dimensions: approx. Ø 2.90 m x height 5.70 m inner dimensions: approx. Ø 2,80 m x height 3.80 m weight: 6 tons output: 42 m³/h year of production: 2000 comm. nr. 22857/3 other: painted blue, threefold epoxy resin coating inside Aboveground pressure tank made of steel, standing vertically on four feet, with two acces holes DN500, one DN300, former gravel filter. Incl. flanged / welded nozzle floor with screwed-in filter nozzles, inner mud funnel, all required connections for untreated water inlet, treated water outlet, backwash in- and outlet and ventilation. This steel tank can be used as gravel filter for filtration, de-icing and ...
The BTS-240 Bin Compactor is ideal for material compacting in your 240 Ltr. garbage and recycling bins. Large bulky rubbish, but also cardboard and recyclable materials can be compacted easily and safe to a minimum of its size. By compacting these waste and recyclable materials you achieve a volume reduction of up to 80%, a significant saving on your disposal costs and you also create a safe and clean working environment. Pressing force: 2 Ton Compaction: up to 80 % (material depending) Machine size: 2360 H x 780 W x 780 D mm Machine weight: 234 kg Transport height: 2360 / 1754 mm (on request) Cycle times: 20 seconds Motor: 1.5 kW 13 Amp Power supply: 220 - 240 V (1 phase) Noise level: 68 dB User-friendly lever control Optimum utilization of garbage bins Reduces the number of waste bins No more climbing into bins Reduces frequency of waste collection A qu ...
RADAX high-pressure duct fan High-pressure duct fan with cylindrical pipe sleeve, flanges on both sides, directly driven. Cylindrical galvanized steel tube Sheet metal, with double-sided moulded Flange, hole pattern according to DIN 24155, recessed built guide wheel. Semi-axial impeller, eight spatially connected curved blades made of thermoplastic, Balancing quality G 6.3 according to VDI 2060 and DIN ISO 1940. Three-phase squirrel-cage motor by Voltage reduction speed controllable, Thermal contacts, closed design, maintenance-free, sealed, low-noise Ball bearings with long-term lubrication. Fan data (default) Seawater version. Also resistant to weak acids and alkalis. NEW!
The BTS-MF300LH is the ideal waste baler for compacting your loose cardboard and plastic film waste into a bale of up to 300 kg. Due to the compact design and low height of under 2 meters this baler is perfect for rooms with limited ceiling heights. The baling press impresses with its ease of use, safe operation and its large filling volume. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Pressing force: 20 Ton Bale weight: up to 300 kg (material depending) Bale size: 1100 H (var.) x 1200 W x 800 D mm Machine size: 1986 H x 1800 W x 1100 D mm Machine weight: 1140 kg Transport height: 1986 mm Loading aperture: 1200 W x 600 H mm Cycle times: 45 seconds Motor: 2.2 kW 16 Amp Power supply: 220 - 240 V (1 phase) ...
SPK KB 2132 eccentric press was manufactured in the USSR in 1980. Operating with a force of 160 tonnes, the press of almost indestructible design offers the highest quality and precision during the most demanding workpiece machining. The machine’s equipment includes among others a pneumatic clutch, a large-area slider performing up to 71 strokes per minute, central lubrication and manual control. The total weight of the press is 13200 kg. Technical data of the SPK KB 2132 press - maximum press force: 160 t - work table dimensions (L x W): 1000 x 700 mm - maximum slider stroke: 160 mm - minimum slider stroke: 25 mm - slider dimensions (L x W): 580 x 460 mm - slider adjustment range: 120 mm - slider stroke rate: 71/min - intermediate plate thickness: 110 mm - distance between work table and slider (slider in lower position, largest stroke, connector unscrewed): 480 mm - bore ...
Nominal force: 6300 ton Number of continuous strokes per minute: 40 Ram stroke: 460 mm Distance between ram and table (table is in upper position): 1150 mm Table adjustment: 15 mm Distance between press columns: 1950 mm Ram dimensions: -front to back: 1680 mm; -left to right: 1680 mm Table dimensions: -front to back: 1950 mm; -left to right: 1920 mm Mechanical upper ejector: -max stroke: 100 mm; -number of positions: 1 -steps of stroke adjustment: 25-30-75 mm -force: 30 ton Pneumatic lower ejector: -max stroke: 300 mm -stepless stroke adjustment: 15-300 mm -number of positions: 3; -force: 65 ton Side windows dimensions: -width: 1100 mm; -height: 1280 mm Main motor: 400/590 kW/rpm Press layout dimensions: 6300x8965 mm Total height: 11125 mm Height above floor level: 9150 mm Total weight: 626100 kg
Technical data: -Compressive force 100 t -Throat 320 mm -Wide stand below the Guide 400 mm -Table size approx. 850 x 610 mm -Discontinued diarrhea hole in the table 335 / 300 mm -thickness of the table clamping plate 90 mm -gr. Height approx. 300 mm -Plunger area 600 x 335 mm -Adjustable height of the RAM 80 mm -Stroke adjustment 10-130 mm -Emissions er hub in the RAM 32 mm -Speed continuous operation approx. 56 / min -Drive 400 V / 11 kW -Space requirement approx. B H 1900 x 2800 X 2200 mm -Weight approx. 9000 kg Starring:-UVV press backup controller PREVENTA -Hydr. + pneumatically actuated clutch -LUTEX auxiliary braking system -Central lubrication
Hi, I offer you Hydraulic power pack-three engines 90 KW each -oil tank 4500l, -Each engine drives two hydraulic pump gear -Pump Model 45V60A Power supply power to the extruder scrap shears in the set are three Dimensions chydrauliczne 160x190 coolers coolers 3 x -cooling connection 100 mm -power connection 80 mm Very Good Condition Net price: 59900 $-€14000 contact: + 48 600-517-834
Qty. 1 Second-hand extrusion press including log furnace Mfc.: SMS Built: 1986 Force: 960 MT (9.3 MN) Press jaw: Wide: 155 mm Height: 140 mm Max. inlet: 130 mm (144 mm block, 5 mm protection per side) Recipient: 149,9 mm Extras: Heatable tool cassette from Marx (installed 2016) Conversion of recipient to resistance heating (beginning of 2016) Punch press disc: 149,2 mm Broaching disc: 150 mm Billet Ø: 144 mm Length: 265 – 540 mm Log length: 3000-4800 mm Log Furnace Mfc.: Extrutec GmbH Built: Temperature: 480-520 °C Zone 1: 460-490 °C Zone 2: 440-470 °C Zone 3: 400-450 °C Table weight: Max. 1350 g/m Min. 80 g/m Electrical control cabinet Puller Exhausting system Cooling device Spare parts for furnace combustion air Spare parts head burner Spare parts oven stove bo ...
TECHNICAL SPECIFICATIONS Manufacturer: HENKE Designation: Production plant for concrete block slabs Type: UNI 2000 Year of construction: 1995 Operating hours: 11,543 h COMPOSED OF: Item 010) Fully automatic rotary table top pressure press UNI 2000/600/7 Item 020) Attachment distribution device for fine-grained attachments Pos. 030) Fully automatic dividing disc dosing unit with 8-fold ejection Item 040) Fully automatic direct washout system "WESER 100/2" for flat laying (horizontal) Item 050) Moulding frame device 400 x 400 mm, 2-fold Pos. 070) 2 x chain conveyor 1.50 m long Item 080/120) Pallet destacker Item 090) Cleaning brush Item 100) Pallet oil roller Item 110) Intermediate transport Pos. 130) Plate removal device Item 160) Stacking arm with bearing block Item 170) Chain conveyor 5 m long Pos. 180) 2 x Plate Pack - Lifting Item 190) Parcel push-off device ...
JJZ-CP type press designed for the production of plywood, doors, MDF. The glued elements are fed and removed from the press automatically by means of driven rollers. The press can be used with glue feeders. Specifications: -max. pressure 500T/ adjustable/ -max. load height 1300mm -max. batch size 1300x2500 -press size 3600x1370x4500 mm -press foundation ~500 mm below the floor level -feeding table 2000x1960 mm -receiving table 2350x2500 mm -max. power 13.2 kW -Ce -capacity of 6 batches per hour Currently, we glue panel doors and MDF board on presses. Very good technical condition. We offer a plywood production line dedicated to these presses.
Pressure capacity: 8000 kg Maximum cutting area - 200 mm2 for material strength 40 kg / mm2 Horizontal radius 200 mm Clearance between the side walls 160 mm Fixed hub 35 mm Pin hole in the Stossel 38 x 60 mm Adjustability of the Stossels 70 mm Weight of 400 kg of the Presse Operating instructions The machine is located in the new value. State, probably never in use. Control actuator Stober
Machine type: Hose press / pneumatic Manufacturer: Peters Type: NDP YOC 2000 Condition: used / good Offer will only be sent if a complete imprint is provided! Price 1.250 Euro incl. 19% VAT free loaded. Location Warstein , Germany Reference M-PET-0124 DESCRIPTION We offer you a used hose press from the manufacturer Peters. Data to follow. Heavy-duty design Pressure 8 bar Availability: immediately Our offer is aimed at tradespeople who are registered within the meaning of the Trade Regulation Act according to §14 GewO. The offer is subject to change, subject to prior sale. Please provide your full contact details to receive a quote with our terms and conditions and payment terms. Errors in the descriptions and offers are excepted!
JR Dare Press Plate: 1400mm x 1400mm Daylight 530 mm 4 x rams Ram diameter - 16” Max working pressure - 1500 PSI Clamping tonnage - 600T Platen heating - strip heaters 18KW / platen
THE WOOD PRESS FOR HIGH-QUALITY FUELS The RUF LIGNUM Classic wood briquette press is ideal for briquetting medium quantities of wood chips that accumulate in the woodworking industry. The briquetting process can generate additional revenue and reduce storage and transport costs. Another advantage is the flexibility of our wood briquette presses. You can press different material grains into high-quality briquettes without the need for a binder. As a result, RUF briquettes have a higher utility value and an optimal CO2 balance as a valuable energy source. Our LIGNUM series also impresses with high energy efficiency and low wear thanks to the innovative RUF hydraulics. YOUR BENEFITS AT A GLANCE - Fully automated 24-hour operation possible -Longevity - Low maintenance costs - Compact design - Direct integration into existing production facilities possible Bto8iej998 - Experience f ...
maximum number of results exceeded
please refine your search
