squaring used for sale

4 sides trimming line

Cutting saw for cutting waste material. Suitable for processing waste after an angle circular saw. The configuration of the machine and its parameters is by mutual agreement. Technical parameters: Power of the main motors: 2 x 11 kW Power of the feed motor: 0.75 kW Minimum height of the starting material: 15 mm Maximum material length: optional Maximum height of the starting material: optional

Brettbesäumer Autojet used Cutting heights 18 - 100 mm, 3 variable axes – 2 variable stems – Re./Li. Additional bushing. Build 3/94 - New laser measurement with PC/software/PC cabinet from Installation 5/2007 A cost-effective solution for a fast trimming machine with modern laser measurement. - Continuous capping with length stops for the cap lengths - Zero cross-cut saw - Addition of swivel saw for tip capping on the opposite side. The waste is disposed of. -Transverse measuring conveyor The boards are conveyed by a measurement curtain in transverse passage. -Laser measurement State-of-the-art surveying with 15 lasers from above. Of course, programs can be stored in all variety, depending on length and width, separation, sharp-edged or forest edge can be mapped in many ways in the program. - Alignment table A computer calculates the ideal orientation of the boa ...

PAUL recutting saw type s-900-L with a passage width 906 mm, Cutting width 180 mm. The feed is infinitely adjustable 0- 90 m-min. The saw motor has 110 kW. Saw blade diameter 550 mm at 2500 rpm. With automatic feeding, Spreiselabscheider double-lamellig with pull-out tapes

SPECIFICATIONS: Max. cutting length: 3000 mm Max. cutting height: 50-60 mm Manual Saw Blade Feed Adjustable cutting width Electric/pneumatic operation

I sell a center saw with continuous HOMAG FPL620/06/15/P S/LQ. Year of construction 2007. Working width 204 - 1304mm Element height 12 - 60mm Cutting width 100mm Blank length 300mm Feed speed 10 - 40 m/min. Configuration: 1 + 1 pcs. cutting units top + bottom 1 pcs. cutting unit flexible top/bottom 1 pcs. cutting unit flexible top/bottom 1 pcs. grooving unit with stop and softforming function Material pressure tape with conveying from above. Continuous machine. Condition Very good. Available same.

Workpiece thickness: 8 - 50 mm Edge thickness: Coil edges 0.4 - 3 mm Feed speed 10 m/min Equipment: manual height adjustment. Joint milling unit, 2 motors Panel edge heating Gluing area Pressure zone 1 driven and 2 non-driven rollers End trims, 2 x 0,8 kW motors, straight and chamfer 15? Top and bottom trimming Profile scraping unit for PVC edging Glue scrapers

Panel thickness: 8 - 50 mm Thickness of the edges: 0,4- 3 mm Feed speed 8 - 11 m / min PU pressure rollers Equipment: Squaring unit, 2 motors 2,2 kW Panel edge heating Edge magazine for coil and strips Hot melt application with roller Airtec AT4510 unit The Airtec aggregate is positioned so you can use Airtec or the standard glue pot Motorized side pressure unit End trims, 2 motors, pneumatic positioning straight and with chamfer trimming unit above / below Contour trimming unit Profile scraping unit Glue scraping unit Polishing unit Detergent spray system central lubrication

Workpiece thickness: 8 - 60 mm Workpiece overhang: 38 mm Edge material of the roll: 0.4 - 3 mm Edge material in strips: 0.4 - 6 mm. Min. workpiece width: 70 mm (with thickness 8-22 mm), 120 mm (with thickness 23-40 mm), 150 mm (with thickness 41-60 mm) Feed speed: 11 m/min Machine equipment: Joint milling unit, 2 x 2.2 kW motor Gluing unit with workpiece edge preheating Pressure zone with driven main pressure roller and 2 non-driven pressure rollers Hood unit, 2 x 0.18 kW, pneumatic adjustment phase/straight Radius and fine milling unit, 2 x 0.27 kW Form milling unit 1 x 0.35 kW Profile scrapers Glue joint scrapers

Fixed side at the left Feedspeed 18 - 25 m/min Working width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mm Panel overhang 30mm Panel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations) Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mm Coil diameter 830 mm Equipment: Sprayers release agent Squaring device with 2 motors each 3 kW Edge heating Edge magazine for 2 coils, guillotine for edges up to 3 mm Glueing part A20 with quickmelt application Lateral pressure zone K, 1 driven and 6 after pressing rollers End trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kW Contour trimming, 2 exchange units Profile scraping PN10 Flat scrapers FA11 Sprayers cleaning agent Buffing Automation package straight/chamfer: -Automatic adjustment infeed fence -Automatic setting of pressure rollers -Pneumatic setting of end trims -Pneumatic setting of rough trims -Automa ...

Single sided edge bander with hot melt, fixed side at the right, pre-milling unit Edge thickness: 0,4 to 12 mm Workpiece thickness: 8 - 60 mm Feedspeed 8-20 m/min (limited to 10 m/min using the contour trimming) Workpiece transport by chain, top pressures with rubber rollers Sound enclosure over all trimming motors Equipment: Adjustable fence Pre-milling with 2 shapers, each 2,2 kW Coil and strip magazine Hot melt unit, Quickmelt type Pressure zone with1 driven and 2 non-driven pneum. Loaded rollers End trims, 2 x 0,35 kW motors, straight and chamfer 15? Top/bottom trimming, motors 2 x 0,35 kW Radius trimmming Contour trimming unit, leading and following edge, 2 x 0,35 kW Radius scraping unit Glue scrapers Buffing unit Controlls PC 20+

Workpiece thickness: 8 - 90 mm, electronically adjustable Feed rate: 18-32 m/min frequency controlled Edge thickness: 0.3 - 3 mm for roll edges, strips up to 20 mm Equipment: Inlet guide automatically adjustable via the control, extension 500 mm Joint milling unit: 2 x 3.0 KW workpiece preheating Gluing unit A34 edging magazine for roll Pressure zone with 1 driven, 6 non-driven rollers, automatic adjustment from the control Cutting unit WK14, straight, 2 motors 0.8 kW Pre-milling unit: 2 x 1.5 KW, pneumatic adjustment Form milling unit FF 12 automatic, 2 motors 0.4 kW radius/phase milling unit FF12 automatic 4 motors 0.4 KW universal milling aggregate controlled UF11, 4 kW Profile scrapers PN20 Glue scrapers Nozzles for detergent and anti-stick Polishing unit Control: Power Control PC22

Fixed side at the left Feedspeed 18 - 25 m/min Working width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mm Panel overhang 30mm Panel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations) Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mm Coil diameter 830 mm Equipment: Sprayers release agent Squaring device with 2 motors each 3 kW Edge heating Edge magazine for 2 coils, guillotine for edges up to 3 mm Glueing part A20 with quickmelt application Lateral pressure zone K, 1 driven and 6 after pressing rollers End trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kW Contour trimming, 2 exchange units Profile scraping PN10 Flat scrapers FA11 Sprayers cleaning agent Buffing Automation package straight/chamfer: -Automatic adjustment infeed fence -Automatic setting of pressure rollers -Pneumatic setting of end trims -Pneumatic setting of rough trims -Automa ...

SCM sliding table saw model SI16E 3200: - 3200mm aluminum carriage - motorized lifting of the blade unit - motorized tilting of the blade unit, with numerical indicator - parallel guide with manual adjustment, usable width 1270mm - main blade D=350mm, speed 4000rpm - scorer D=120mm, speed 8500rpm - Main blade motor KW 5.5 / HP 7.5 - Engraver motor KW 0.75 / HP 1 Machine in compliance with CE regulations. Year 1998 Available from the end of September / October 2026