single used for sale

Manufacturer: Ott, Type: Euromatic FÜ, Year: 2001, Program: yes, Control: SPS, Work piece width min-max mm: 60 , Min.-max. workpiece length in mm: 60, Min.-max. workpiece height in mm: 10 - 60, Kantenmaterial min-max mm: 0,2 - 15, Vorschub min- max m/min: 12 - 20, Mitre stations: yes, Fasefräsen: yes, Flat scraper: yes, Rolle/Riemen: Rollen, Machine lenght mm: 8500, Wight approx. kg: 4200, Year :2001

Manufacturer: Lange Kantenfräsgerät, Type: B 600, Year: 2009, Moulding spindles: 2, Routing: yes, Min.-max. workpiece length in mm: 8-60, Vorschub min- max m/min: Handvorschub, Mitre stations: yes, Mitre stations: yes, Radiusfräsen : 1,5 mm, FREE TEXT: Fräsmotore Frequenzgeregelt, Year :2009

Manufacturer: HolzHer, Type: 1411-1, Year: 2001, Work piece width min-max mm: 60, Min.-max. workpiece length in mm: 230, Edgeband height max mm: 50, Thickness of coiled edgeband max mm: 3, Vorschub min- max m/min: 11, Glue system granulate/cartridge: Patrone, Buffing unit: yes, Machine lenght mm: ca. 4.100, Wight approx. kg: ca. 1.100, Year :2001

Manufacturer: HolzHer, Type: Sprint 1310, Year: 2006, Edgeband height max mm: 45, Thickness of coiled edgeband max mm: 3, Vorschub min- max m/min: 10, Mitre stations: yes, Glue system granulate/cartridge: Patrone, Mitre stations: yes, Radiusfräsen : yes, Buffing unit: yes, Top pressure belt/roller: rolle, Compressed air bar: 6, Machine lenght mm: 3, Year :2006

Manufacturer: Soenen, Type: SHCR, Year: 1996, Winkelschweissungen im Bereich von min-max Grad: verstellbar, Mit Schweissraupenbegrenzung an Tisch- und Spannplatten: yes, Spannhöhe min-max mm: 30-90, Kämpfer schweissen im Stumpfschweissverfahren: yes, Spannhöhe min-max mm: 30-90, Spannzylinder pneumatisch: yes, Schweissspiegel und Profilanschlag kommen von unten: yes, Einstellbare Schweissraupenbegrenzung: yes, Ausricht-, Abschmelz- und Stauchanschläge: yes, Digitale Anzeige der Schweisstemperatur: yes, Wight approx. kg: 500, Year :1996

Single-girder overhead crane Manufacturer: Demag Lifting capacity 8to Average track approx. 19.5m Lifting height min 6m With built-in crane scale / lifting weighing device. Hoist runs on the side of the beam so that the crane hook can be lifted to the lower edge of the beam. Crane system has already been dismantled. Optionally with approx. 2 x 50m crane rails.

Overhauled machine, single-shaft shredder LINDNER JUPITER 2200 It is made for the single-stage processing of untreated municipal, industrial and commercial waste into medium-calorific substitute fuels (40 – 120 mm) – the ideal raw material for thermal utilisation in the cement plant's calciner. Lindner Jupiter 2200 Rotor equipped with flat blades. Year of construction 2015 Control cabinet with FU ABB Control panel Drive motors : ABB 2x132 kW Funnel Hydraulic Discharge belt Total weight approx. 32 t Shipping time: immediately

Offer 24591 Specifications: - Max. pressing force 25 t - Max. ram stroke 500 mm - Lifting speed 0 - 40 mm/s - Return 0 - 200 m/min - Installation height 800 mm - Projection to the middle of the ram 360 mm - Pusher clamping surface 440 x 360 mm - Plunger clamping pin 40 mm - Table size 630 x 500 mm - Table height above floor 710 mm - Thermoforming force 10 t - Largest deep-drawing depth 160 mm - Drive 400 V / 4 kW - Space requirement approx. W 800 x H 2720 x D 1150 mm - Weight approx. 2500 kg

Single column pneumatic press, hydraulic press PAUL ANTON type PVT 2Pneumatic table press, embossing pressFabr. No. 97148 Year of construction approx. 1980Compressive force: 10 tonProjection: 100 mmPlunger stroke: approx. 25 mmPlunger surface: 32 mmTable size: 250 x 220 mmTable opening: 53 x 53 mmTable height: 1060 mmInstallation height: 155 mm- very stable construction- Hydro-pneumatic press with pressure transmission air on oil- pneumatic foot switch- Plunger with internal thread M12- Metal substructureSpace requirement L x W x H 850 x 620 x 1560 mmWeight

pressure: 75 t throat: 280 mm stroke: 303 mm total power requirement: 15 kW weight of the machine ca.: 7000 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 25 t throat: 250 mm stroke: 100 mm total power requirement: 7,5 kW weight of the machine ca.: 3200 kg dimensions of the machine ca.: 1000 x 1700 x 2600 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 60 mm turning length: 200 mm number of slides: total power requirement: 20 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 10 t throat: 0 mm stroke: 400 mm total power requirement: 7,5 kW weight of the machine ca.: 6500 t dimensions of the machine ca.: m D U N K E S (Germany) CNC Controlled Hydraulic Double Column Press Model HD 10 Year 1993 ________________________________________________________ Pressure 10 tons Ram stroke 400 mm Mounting height 600 mm Table size 400 x 300 mm Table height above floor 820 mm Ram area 400 x 300 mm Ram bore 40 mm Quickspeed, downwards, max. 70 mm/s Working speed, downwards, using max. pressure 40 mm/s Working speed, min. 5 mm/s Working speed adjustable from 5 - 70 mm/s Return stroke speed, min./max. 20 / 175 mm/s Drive 7.5 kW Total electrical load, approx. 12 kW - 380 V - 50 Hz Weigh ...

turning diameter: 1250 mm swing diameter: 1160 mm turning height: 800 mm faceplate diameter: 1000 mm total power requirement: 97 kW weight of the machine ca.: 25000 t dimensions of the machine ca.: m P I T T L E R (Germany) CNC Controlled Vertical Turning and Milling Centre With Tool Changer and Pallet Changer Model PV 1250 / 1-1 Year 1994 _______________________________________________________ Turning Ø max. 1,000 mm Swing Ø max. 1,160 mm Turning length 800 mm X Axis - horizontal 1,300 mm Y Axis - vertical 800 mm Feed / quick feed 16,000 mm/min Main spindle speeds 10 - 1,000 rpm ! Main spindle speeds via separate C Axis 0.1 - 16 rpm Positioning accuracy of C Axis 360° + / - 5 Tool holder ISO 50 Tool drive 22 kW Max. torque / spindle speed 315 Nm / 2,500 rpm Pallet size 630 x 630 mm Spindle drive 63 kW Total electrical load 97 kW - 400 V -  ...

SINGLE SHAFT SHREDDER, V Rotor width 1.500 mm. Rotor diameter 500 mm 16.69″ Motor power 90 kW n.82 knives 60 x 60, adjustable counter-knife, off-set rotor bearings (low maintenance), V-Rotor with knife pockets, Welded knife holders with screwed knives and covered bold heads, Offset rotor bearings ( low-maintenance / closed ), Fast hydraulic backwards incl. different settings by PLC control and anti shock valve, Shredding room unpainted, Movable screen basket (electro-hydraulically), Screen thickness 10mm, Hydrodynamic starting clutch (energy saving system for machine start), Electromechanical drive with heavy duty gearbox, Control cabinet incl. 5m cable, Electrical control system Siemens S7 PLC control, Reverse counter and transmission limit switch (safety package), Star-delta starter, Universal joints for piston with ram impulse and load-related ram function, Machine frame on anti - v ...

PVC PROFILE EXTRUSION LINE EVC BRAND, single screw extruder with 60 mm 28 LD, constructed in 1998, for 180 mm max width, 44 kw drive, control panel, Calibrating desk 3,7 m.long with 1 x 9 kw.pump, Caterpillar pull off unit, 180 mm wide, saw, 6,0 mt.long discharging table.

hydraulic: ja : 100 t weight of the machine ca.: 2,9 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 35 mm, 25 , 103 U/min

Used extruder 35mm - 25 l/d with 5.6 kW drive 3-zone auger 3 heating/cooling zones on the cylinder + 1 tool zone Mass pressure sensor 500 bar All machine cables designed to be plugged in Control cabinet with main switch, motor controller, mass pressure indicator and 4 pieces of temperature controller Function-tested

pressure: 40 t throat: 240 mm stroke: 8-88 mm no. of strokes: 57/86 Hub/min ram - range of adjustment: 63 mm table surface area: 560x450 mm ram surface: 240x200 mm hole in the table: Ø100 mm table height: 840 mm tool hole in ram: Ø40 mm weight of the machine ca.: 3,5 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 200 t throat: 440 mm stroke: 19-230 mm no. of strokes: 58 Hub/min ram - range of adjustment: 100 mm table surface area: 1450x850 mm ram surface: 900x680 mm hole in the table: 300x300 mm table height: 950 mm tool hole in ram: Ø60 mm weight of the machine ca.: 19 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 1000 t stroke: 600 mm weight of the machine ca.: 4 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Single column - eccentric press KRUPP type PEKRD 125 hMasch. No. 2861 Year of construction 1977Compressive force 125 ton. Projection 400 mmTable size 950 x 750 mmPlunger area 800 x 540 mmTable opening 100 x 250 mmStroke adjustment 8 to 160 mmPlunger adjustment 100 mmInstallation height largest stroke at the top max. 550 mmStroke rate 60 strokes/min. Table height above floor 800 mmEngine power 10 kWNetz connection 380 Volt, 50 Hz- Hydraulic overload in the plunger- Compressed air clutch-brake combination ORTLINGHAUS-

Single column hydraulic press, straightening press, punching bracket ECKOLDPressen frame with hydraulic cylinder, mobile press, punching unitType RSD 1500 - 125Masch. No. 317 / 690 Year of construction approx. 1986Compressive force 150 ton. Projection 125 mmSlide stroke 35 mmTable size 280 x 210 mmPlunger area 125 mmInstallation height (plunger to table) max. 265 mmTable height above floor 403 mmHydraulic operating pressure max. 500 bar- without hydraulic unit- Lifter surface with 4 threads M16 and 20 mm guide groove, one centering hole in the middle 15

Single column - eccentric press WEINGARTEN type ERV 40Masch. No. 537 / 65 Year of construction 1965Compressive force 40 ton. Projection 230 mmTable size 570 x 470 mmPlunger area 250 x 200 mmClamping pin hole 40 mmInstallation height max. approx. 520 mmStroke adjustment 8 - 88 mmPlunger adjustment range 63 mmStroke rate 70 strokes per minuteDrive power 3 kWNetz connection 380 volts, 50 Hz- Table height adjustment- Overload protection by crushing plate- Clutch-brake combination by WEINGARTEN friction threaded coupling-

Single column - eccentric press WEINGARTEN type ER 63Masch. No. 52A / 63 Year of construction 1963Pressure capacity 63 ton. Projection 280 mmTable surface 630 x 530 mmAdjustable plunger stroke 8-100 mmPlunger adjustment 63 mmStroke rate 65 strokes / min. Engine power 4 kWNetz connection 380 Volt, 50 Hz- Clutch-brake combination by WEINGARTEN friction threaded clutch- Electrical stroke release via foot switch- Wheel counters- Overload protection by crushing plate- Front crankshafts Support bearingSpace requirement L x W x H 1500

Single column - eccentric press PELS - RICHTER type PEKR 125Masch. No. 20684 Year of construction 1967Compressive force 125 ton. Projection 430 mmTable size 1100 x 750 mmPlunger area 890 x 650 mmTable opening 400 mmStroke adjustment 6 to 115 mmRam adjustment 100 mmInstallation height largest stroke top max. 450 mmClamping pin bore 50 mmStroke rate 60 strokes/min. Table height above floor 900 mmMotor power 7.5 kWNerg connection 380 volts, 50 Hz- overload protection by crushing plate in the plunger- compressed air

Single column hydraulic press SCHÖN type TES/CBbuilt in 1977Compressive force 63 ton. (160 bar)Projection 320 mmTable size 600 x 770 mmPlunger area 600 400 mmPlunger stroke 125 mmInstallation height max. 400 mm (with intermediate plate on the ram)Slide speed Rapid traverse downwards approx. 180 mm/sec. Ram speed work approx. 25 mm/sec. Pushrod speed upwards approx. 180 mm/sec. Table height above floor 870 mmDrive power 22 kWNet connection 380 volts, 50 HzTank capacity approx. 280 litres Hydraulic oil

Single column hydraulic press SCHULZ type SES 250Masch.Nr. 04.86.3511/3 Year of manufacture 1986Compressive force 25 ton. Retraction force 10 toProjection 360 mmTable surface 600 x 720 mmPlunger area 500 x 500 mmFailure opening in table 100 mmPin hole 40 mmPlunger stroke 400 mmInstallation height max. 600 mmTable height above floor 935 / 775 mmTank capacity hydraulics 380 litresDrive power 7.5 kWNet connection 380 volts, 50 Hz- Fixed stop adjustment in the press cylinder 180 mm- Light barrier

Single-column eccentric press MÜLLER GEFREES type PDET 5 S/EKMasch. No. Year of manufacture 1988Compressive force 5 ton. Projection 125 mmColumn passage 170 mm Table surface 280 x 220 mmWaste height 90mmLifting area 160 x 100 mmLifting adjustment 4 to 40 mmRam adjustment 30 mmInstallation height largest stroke at the top max. 210 mmStroke rate 200 strokes/min. Clamping pin bore 25 mmTable height above floor 900 mmEngine power 0.55 kWNerg connection 380 volts, 50 Hz- pneumatic clutch-brake combination-

pressure: 20 t throat: 200 mm stroke: 0 - 50 mm table:: 360 x 550 mm table:: 140 mm - Bohrung no. of strokes: 160 Hub/min bore: 35,0 mm - Werkzeug compressed air: max. 6,0 bar dayligth: 240 mm total power requirement: 2,2 kW weight: 1.250 kg range L-W-H: 1310 x 1250 x 1860 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Stock# UG6388 Little used single screw extruder by Farmet (CZ) model FE100 WE Clever Max. Machine can reach output in range from 90-130 kg/h. Power consumption 16 kW. Includes water pump, die cutting knife, some toolings. Local control panel with plc controls. Previously tested on animal food production. Dims: L 195 cm x W 102.5 cm x H 178 cm x weight 600 kg.

Key data: 100 t

Sale due to switch to eccentric press Pressing force 100 tons Loading depth 360 mm Stroke 500 mm Daylight 800 mm Plunger area 530 x 400 mm Table height above floor 710 mm Working speed 10mm/sec Approach speed 150 mm/sec Return speed 150 mm/sec Required power 17 kW Dimensions L x W x H 1,400 x 2,000 x 3,200 mm Weight of the machine approx. 5.1 t Year of manufacture 2001 Price is net, VAT can be claimed. Loading facilities available All information without guarantee

pressure: 63 t throat: 260 mm stroke: 8-100 mm ram - range of adjustment: 63 mm no. of strokes: 115 Hub/min : 316 mm table surface area: 630x490 mm ram surface: 315x260 mm hole in the table: Ø 140 mm total power requirement: 4 kW weight of the machine ca.: 7,5 t dimensions of the machine ca.: 2000x2000x2700 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Single Column Press Dunkes TYPE: HZS 160 Specifications: Manufacturer: Dunkes Model: HZS 160 Operating hours: approx. 2250 The machine is in good condition and fully functional.

Planetary Gearbox PCEF53.5-X1 New For Doppstadt DW2560B, DW3060 standard, mobile & stationary Not suitable for Biopower models (42 teeth on the roller)! Fully assembled with output flange and driver

A bevel gear rolling test machine Gleason is available. Workpiece diameter: 330mm, max. center distance: 203mm, driver spindle nose distance range: 100mm-250mm, max. offset range upper/lower: 203mm/50mm, driver spindle bore: 99mm, driver spindle taper per meter: 15.5mm/m, counter spindle bore: 58mm, counter spindle taper per meter: 12.7mm/m, spindle speed: 1500rpm, test angle range: 0°-180°, driver spindle repeatability: +/-0.004mm, runout: +/-0.003mm, machine dimensions X/Y: approx. 1550mm/2050mm, weight: approx. 2400kg. An on-site inspection is possible.

Holzzerkleinerer ( Holzhäckler ) maschine modell MION MOSOLE TR 2 gebrauchte maschine Maschinenbedienung im Automatik- und/oder Handbetrieb modus Arbeitsbedingungen: ausgezeichnet Im Automatikbetrieb startet der Motor in die entgegengesetzte Richtung, um den Stopfer von eventuellen Rückständen vorheriger Arbeiten zu befreien. Im Vollautomatikbetrieb stoppt der Motor nach ca. 5 Sekunden und startet erneut in die richtige Richtung für eine kontinuierliche Bearbeitung (siehe Video). Technische Daten : hydraulischer Schieber Breite Rotor mm.700 Durchmesser Rotor mm.300 Drehzahl Zerkleinerungseinheit 100 U/min Trichterinhalt 3.42 m³ Hauptmotor PS 25 Hydraulikaggregat Motorschieber PS 1 auswechselbare Messer Beschickung von oben

Komptech Terminator 5000 SD Category: Garbage Shredders Specification: Category: Universal Waste Shredder Serial / reference number: 481148 Power: 446 hp / 328 kW Weight: 27 000 kg Emission class: Tier 4 Final / Stage V Equipment and description: Terminator 5000 S Diesel engine: CAT C13 Tier 4 Final/Stage V F-Crushing Unit Armoured rollers – new Sickle teeth Hydraulically adjustable cutting gap 0-45 mm Overbelt magnet Central lubrication Remote control

Screw Diameter: 75 mm // Throughput: 700 kg/h

Screw Diameter: 35 mm // Output Capacity: 25 kg/h

VMC ECO S-1.800, Rotor length 1.800 mm, 132 kW Drive 380-400V 3Ph, 420 A 60Hz. IP55, complete with loading hopper, hydraulic ram 11 kW, hydraulic power station, 60 mm screen (or bespoke), control panel, good working conditions, Constructed in 11-2001, Users manual, electrical drawings, CE compliance., offered AS IS WHERE IS, installed power - used power in work: about 60-65% : 132 kW, availability: May 2026, working width: 1.800 mm., options available: loading belt, extraction system, capacity: depending on materials and feeding rate, conditions: Very good, type: single shaft - electric

Offer 25374 Specifications: - Max. pressing force 100 t - Max. ram stroke approx. 500 mm - Lifting speed 25 mm/sec. - Return 125 mm/min - Installation height approx. 1000 mm - Projection to the middle of the ram 380 mm - Pusher clamping surface 530 x 400 mm - Plunger clamping pin 40 mm - Table size 750 x 560 mm - Table hole / through hole in the table 200 mm - Table height above floor 720 mm - Oil filling quantity approx. 200 ltr - Drive 400 V / 11 kW - Space requirement approx. W 1150 x H 3250 x D 1850 mm - Weight approx. 4600 kg

Screw Diameter: 160 mm // Output Capacity: 1400 kg/h

Screw Diameter: 100 mm // Output Capacity: 600 kg/h

Screw Diameter: 65 mm // Output Capacity: 170 kg/h