shears used for sale

Guillotine shears, FASTI type 506-10-2,5 Masch. Nr. 96-506-018 Year of manufacture 1996 Cutting length 1030 mm Cutting thickness 2.5 mm Working height 850 mm Drive power 4 kW Mains connection 400 volts, 50 Hz. - mechanical sheet metal hold-down - electric foot switch - simple backgauge 550 mm with handwheel adjustment - 2 support arms 550 mm - angle stop right 750 mm - protective housing SICK behind the machine - control cabinet fixed to the machine space requirement L x W x H 2150 x 1650 x 1400 mm weight 650 kg good condition; used

guillotine shears, sheet metal shears DIGEP type OL 3 Fabr. No. 1312 Year of construction 1977 Cutting length 1250 mm (nominal cutting length)Cutting length max. 1300 mm Cutting thickness at 450 N/mm² 3 mm single backgauge 500 mm Column projection 200 mm Cutting angle 2 Stroke rate at full cutting length max. 50 strokes/min. Working height 860 mm Motor power 2.2 kW Mains connection 380 volts, 50 Hz - LED cutting area lighting - simple backgauge with manual adjustment - Mechanical foot switch - Front angle stop left - 1 piece front sheet metal supports 300 mm Space requirement L x W x H 1660 x 1350 x 1200 mm Weight 1600 kg good condition; used

Shears cnc 3000 x 6, year 3003 Folder: 4000 x 80 Ton Variable angle notching machine with punching head. Machines in excellent condition that worked for a private company or not for third parties.

4-fold combined profile steel shears PEDDINGHAUS type Peddy Masch. No. GJ 4405 Year of construction 1970 Notching device: rectangular notch 40 x 40 to 7 mm sheet steel Punch dimension 40 x 50 mm - stroke rate 40 strokes/min. - Table support 750 x 260 mm Profile steel shears: Profile shears at 90 angles 70 x 70 x 7 mm Profile shears at 45 angles 50 x 50 x 6 mm Bar steel shears:Cutting capacity round 28 mm Cutting capacity square 25 x 25 mm Flat steel shears: Cutting capacity max. 10 mm cutting capacity flat 80 x 6 mm- blade length 175 mm- usable length 135 mm - shear angle approx. 2 motor power 1.5 kW mains connection 380 volts, 50 Hz. - mechanical stroke tripping - bogie with material support Space requirement L x W x H 1200 x 750 x 1700 mm Weight 500 kg good condition; used

Plate shears, sheet metal shears, sheet metal shears, crank plate shears, guillotine shears -Manufacturer: Fasti, mechanical guillotine shears type 506/20/2 -Cutting width: 2030 mm -Max. Cutting thickness: 2.0 mm -Back gauge: adjustable by hand -Throat: 545 mm -Stroke: continuous stroke / single stroke / tapping -Setup dimensions: 2505/1650/H1150 mm -Transport dimensions: 2505/1100/H1150 mm -Weight: 1200 kg

ERMAK CNC HVR 3100 x 13 hydraulic guillotine shears built in Turkey in 2008, are designed for cutting workpieces made of among others mild steel or stainless steel. The metal sheet with a maximum length of 3100 mm and a maximum thickness of 8 mm (plain steel) or 13 mm (stainless steel), is held during machining by 14 hydraulic clamps. The angle of the cutting blade can be freely adjusted in the range from 0.5° to 2.0°. Full control over the operation of the CNC HVR 3113 machine is guaranteed by the control panel located on the guillotine shears body with installed CYBELEC DNC 60 CNC controller, allowing programming of many different machining processes. The guillotine shears is equipped with among others new cutting blades and a foot control pedal, making the operator’s work much more comfortable and simple. The total weight of the machine is 13400 kg. The total weight of the mach ...

DURMA SB 3020 hydraulic guillotine shears built in 2008 in Turkey are an ideal choice for machining stainless steel, copper, aluminium and plain steel. Workpieces with a maximum thickness of 20 mm are cut using extremely precise, hardened cutting knives with manual adjustment of the gap between the blades. The high-quality monoblock design, combined with the hydraulic system, additionally ensures the highest stability and machining performance, even during the most demanding challenges. To facilitate the operator’s work, special transport rollers have been integrated into the work table, on which the workpiece is fed directly under the cutting line. The machining parameters are programmed in the intuitive DURMA ENC 100M control panel with clear LCD display and memory for 50 programs. The DURMA SB 3020 guillotine shears also features a driven back stop with T-slots and sockets with d ...

Sheet metal shears, sheet metal shears, sheet metal sheet shears, crank sheet metal shears -Manufacturer: Cidan, mechanical guillotine shears type MS-M 10/3 -Cutting width: 1040 mm -Max. Cutting thickness: 3.0 mm -Back gauge: 500 mm -Throat: 660 mm -Setting dimensions: 1840/1330/H1130 mm -Transport dimensions: 690/1330/H1130 mm -Weight: 880 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Hand lever shears: sheet metal and round steel shears -Blade insert length: 300 mm -Round steel: up to approx. 17 mm -Total dimensions: 500/145/H1325 mm -Transport dimension: 1000/145/H450 mm -Weight: 38 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Hand lever shears: sheet metal and round steel shears -Blade insert length: 200 mm -Total dimensions: 380/160/H1160 mm -Transport dimension: 830/160/H500 mm -Weight: 25 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Hand lever shears: sheet metal and round steel shears -Blade insert length: 200 mm -Round steel: up to 15 mm -Total dimensions: 460/160/H1230 mm -Transport dimension: 1000/160/H440 mm -Weight: 23 kg

Hand guillotine shears, guillotine shears, sheet metal shears, sheet metal shears, folding machine, edging bench -Hand guillotine shears combined with: folding machine -Cutting width: 610 mm -Max. Section thickness: 1.0 mm -Swivel bending machine -Max. Working width: 610 mm -Max. Sheet thickness: 1.0 mm -Transport dimensions: 845/910/H1230 mm -Weight: 240 kg

Profile steel shears, hand lever shears, hand sheet metal shears, sheet metal shears, sheet metal shears -Scissors: 185 mm -cutting: 40 mm angle iron -cutting: Ø mm round steel -Dimensions: 460/985/H2220 mm -Weight: 88 kg

Combined profiled steel shears and hole punch GEKA type HYD 80 / Hydracrop 80/A Masch. No. 9566 Year of manufacture approx. 2000 Punching force 80 ton. Projection 300 mm Punching up to 40 mm in 14 mm sheet metal Flat material shears 450 x 15 mm Angle steel shears 130 x 130 x 13 mm 4-point shears 45 x 45 mm Round material shears 45 mm Rectangular notchers up to 12 mm Motor power 5.5 kW Mains connection 400 Volt, 50 Hz stop with el. Lifting release 500 mm - Work table with stop for the hole device 550 x 380 mm - Working height of the hole device 1100 mm - Work table with stop for the rectangular notcher 550 x 400 mm - Working height rectangular notcher 930 mm - Approx. 21 pieces of various punching tools - Operating instructions - Original painting, not repainted Space requirement L x W x H 1800 x 1150 x 1950 mm Weight 1.7 ton. very good condition; used

Combined lever shears make PEDDINGHAUS type 5 RP 10Machine -No: 992815Technical specifications:Blade length: 175mmPerformance sheet steel up to: 10 mmPower angle iron: 80 x 8 mmPerformance bar steel shears round: 22 mmPower bar steel shears square: 20 mmPerformance profile steel shears: 60 x 7 mmDimensions approx.: 700 x 200 x 700 mmApprox. weight: 107 kgused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Hand lever shears, long-knife sheet metal and round steel shears, lever shears, long-knife sheet metal shears -Manufacturer: Victoria, long-knife tin snips on a mobile stand -Blade insert length: approx. 350 mm -Sheet steel: up to approx. 4 mm -Rectangular profile: up to approx. 7 mm -Total dimensions: 1030/500/H1900 mm -Weight: 109 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears -Blade insert length: 200 mm -Steel sheet: up to 7 mm -Flat/band iron: up to 100x9 mm -Round steel: up to 20 mm -Rectangular profile: up to . 18x18mm -Lever arm: with rack and pinion translation -Total dimensions: 540/180/H1570 mm -Transport dimension: 1250/180/H490 mm -Weight: 44kg

Hand lever shears, long-knife sheet metal and round steel shears, lever shears, long-knife sheet metal shears -Manufacturer: Victoria, Long Knife Tin Snips -Blade insert length: approx. 350 mm -Sheet steel: up to approx. 4 mm -Rectangular profile: up to approx. 7 mm -Total dimensions: 670/180/H1260 mm -Weight: 55 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears -Blade insert length: 200 mm -Round steel: up to approx. 20 mm -Rectangular profile: up to approx. 19x19 mm -Lever arm: with rack and pinion translation -Total dimensions: 455/170/H1540 mm -Transport dimension: 1230/170/H440 mm -Weight: 49 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears -Blade insert length: 150 mm -Round steel: up to 12 mm -Lever arm: with locking spring -hold-down: -Total dimensions: 320/120/H1260 mm -Transport dimension: 990/120/H310 mm -Weight: 12 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears type 3 S / 4 L -Blade insert length: approx.300 mm -Steel sheet: up to 4 mm -Flat/band iron: up to 70x6 mm -Round steel: up to 13 mm -Cutting capacity: see photo nameplate -Hold-down device: continuously adjustable -Number: 2x lever scissors available -Price per piece -Total dimensions: 500/160/H1480 mm / 500/160/H1180 mm -Transport dimension: 1180/160/H430 mm -Weight: 32/30 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears type 3/5 R -Blade insert length: 200 mm -Steel sheet: up to 5 mm -Flat/band iron: up to 60x6 mm -Round steel: up to 13 mm -Cutting capacity: see photo nameplate -Total dimensions: 380/160/H1310 mm -Transport dimension: 970/160/H470 mm -Weight: 23 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears type 3S / 6 R -Blade insert length: 200 mm -Steel sheet: up to 6 mm -Flat/band iron: up to 70x7 mm -Round steel: up to 13 mm -Cutting capacity: see photo nameplate -hold-down: -Total dimensions: 385/160/H1500 mm -Transport dimension: 1160/160/H400 mm -Weight: 24 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears type 3/5 R -Blade insert length: 200 mm -Steel sheet: up to 8 mm -hold-down: -Total dimensions: 385/160/H1280 mm -Transport dimension: 960/160/H390 mm -Weight: 22 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears -Blade insert length: 280 mm -Round steel: up to 14 mm -Total dimensions: 500/160/H1250 mm -Transport dimension: 930/160/H420 mm -Weight: 30 kg

Hand lever shears, long knife, sheet metal and round steel shears, sheet metal shears -Sheet metal and round steel shears: Type 3 BR 4 300 -Steel sheet: up to 4 mm -Round steel: up to 13 mm -Knife length: 300 mm -Downholder: infinitely adjustable -Underframe: massive steel construction -Dimensions: 335/575/H2080 mm -Weight: 103 kg

Hand lever shears, long knife, sheet metal and round steel shears, lever shears -Mubea: sheet metal and round steel shears -Cutting insert length: 200 mm -Dimensions: 380/160/H1240 mm -Weight: 22 kg

We supply round and flange ring shears (circular shears) in two sizes - 3/1300 and 5/1800 Our KS circular shears are PLC - controlled hydraulic - electromechanical machines designed for the production of rounds and flanges made of steel sheet, VA stainless steel sheet, Aluminium and non-ferrous metal sheet, maximum shearing performance for sheets with a tensile strength of 400 N/mm2 - 0.5 mm to 3 mm or 0.5 mm to 5 mm, smallest / largest cutable circular board 150 mm / 1,300 mm or 1,800 mm respectively – cutting speed up to 35 m/min, drive power 5 kW or 7.5 kW, weight approx. 2,000 kg and 3,000 kg

Hand lever plate shears and profile steel shears Knife length 400mm Cuts sheets up to 5mm Cuts round steel up to 13mm Heavy and stable design with foldable storage table. Mounted on base More hand lever plate shears in stock, also for round steel and profiles!

BOSCHERT G CUT 2504 CNC guillotine shears were manufactured in 2014 in Germany. The guillotine is designed for cutting metal sheets with a maximum length of 2600 mm and a thickness of 4 mm (mild steel st42) or 2 mm (stainless steel). The sheet metal is held in place by 13 hydraulic clamps and, thanks to the installed CNC controller with touch panel, it is also possible to store many different work programmes, making the machine very useful and versatile. After entering the parameters of the steel sheet to be cut, the controller automatically sets the cutting gap, choices the angle of the upper knife and the appropriate pressure force and then starts the cutting process. The guillotine is also equipped with, among other things: a foot control to facilitate the operator’s work, light curtains to prevent a worker from entering the working area of the machine and an automatic metal shee ...

Key data: 3100 mm, 6 mm

HACO TS 3006 hydraulic guillotine shears manufactured in Belgium in 2006, are used in manufacturing plants to cut steel sheets with a maximum length of 3100 mm and a thickness of 6 mm. The machine has vertically aligned knives with four cutting edges, which ensure high precision and quality machining of workpieces regardless of the thickness and type of sheet. The angle of the cutting knives and the gap between them are adjusted by means of two levers at the rear of the machine. During machining, the workpiece is pressed against the cam in order to take an accurate measurement on the gauge located between the front stop and the bottom knife. Two parallel hydraulic cylinders drive the cutting bar (the upper knife attached to the slider) to perform the movement in the up-down direction. The HACO guillotine shears are offered with equipment which includes a foot control, a modern HACO SP ...

METALPRES NHM 3006 hydraulic guillotine shears built in the Czech Republic in 2000, are used for precision cutting of black or acid-resistant steel sheets with a maximum length of 3000 mm. The NHM 3006 T guillotine shears have been regularly serviced and upgraded throughout their lifetime. In 2023, a general overhaul was performed with a net value of approximately PLN 16000, during which seals, clamps, controls, electrical installation with cabinet were replaced and the knives were sharpened. The price of the machine also includes a rack with saw for steel and a rack for sheet metal shown in the photos. The total weight of the METALPRES NHM 3000 3M machine is 2000 kg. Technical specifications of the METALPRES NHM 3006 guillotine shears - maximum cutting length: 3000 mm - maximum workpiece thickness (acid-resistant steel): 5 mm - maximum workpiece thickness (black steel): 6 mm - di ...

Engine. Guillotine Shears Impact Shears Tin Shears Scissors Cutting Manufacturer: KRAMER Model TM IIa 3000x4,5 max. cutting length 3050 mm max sheet thickness at ST 40 4.5 mm Distance between uprights 3050 mm Projection 130 mm Table width 360 mm Strokes per min 30 pcs. Hold-down device 16 pieces Manual backgauge travel 5 – 550 mm Engine power 7.5 kw Machine weight 4000 kg Space requirements: W 3480 mm D 3600 mm H 1400 mm Foot switch Back gauge front support arms Angle stop The machine is in good condition and ready for immediate use. Machine runs very quietly. Forklifts available, freely loaded trucks Cheap shipping possible Location of the machine 48324 Sendenhorst for enquiries 0157-35496006 The price is net plus 19% VAT.

DURMA MS 2004 guillotine shears were built in 2008 in Turkey. The machine, characterised by the application of many facilities and modern solutions, guarantees precise and efficient machining of, among others, stainless steel, aluminium, copper and plain steel. A sheet metal with a maximum thickness of 4 mm is fed through ball transfers built into the work table, whose design protects the surface of sensitive materials from scratches and nicks. All machining process parameters are programmed on the intuitive DURMA ENC-100M control panel with a clear LCD display and memory for 50 programmes. During the cutting process, the rigid design of the machine ensures that sheet deformations are within tolerance, making both the workpiece and the cut-off ready for further machining. The DURMA MS-2004 mechanical guillotine shears are offered with direct drive, high-quality cutting knives with adj ...

Specifications: - Flat steel shears cut up to 450 x 15 mm - up to 300 x 20 mm - Profile steel shears - cuts L-steel at 90° up to 150 x 13 mm - Steel bar shears - cuts round steel up to 45 mm - Square steel up to 45 mm - Notching device up to 12 mm - no notching tool available! - Hole punch - punching force 850 KN - with stop table - Projection 510 mm - punches in steel up to 26 mm Ø in 22 mm - 50 mm Ø in 12 mm - various punches + matrices - Support table - E. Contact stop - Drive 400V / 7.5 kW - Space requirement approx. W 1050 x H 1900 x D 2300 mm - Weight approx. 2850 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Hand lever snips: tin snips with stop and stable base -Blade insert length: Approx. 160 mm -Lever arm: with rack and pinion translation -Hold-down device: continuously adjustable -Total dimensions: 1000/780/H1870 mm -Transport dimension: 1000/780/H1300 mm -Weight: 100 kg

Hand lever shears, long knife, sheet metal and round steel shears -Peddinghau: s 4R/7, long knife, sheet metal and round steel shears -Particularly stable scissor body made of: tempered steel -Lever arm with: safety spring -Infinitely adjustable: hold-down device -Steel sheet up to: 7 mm -Round steel up to: 20 mm -Square: 18 mm -Cutting length up to: 170 mm -Performance specification for: material with a strength of 450 N/mm² -Dimensions: 770/650/H2250 mm -Weight: 91 kg

Key data: 2500 mm, 3 mm

powerful crankplate shear WMW ScTP 3.15x2500 - Precise cutting with 10 tons of cutting force - With the powerful cranked clasp shear from WMW, type ScTP 3.15x2500, we offer a reliable cutting machine for precise sheet metal processing. With a cutting force of 10 tons and a torque of 27,500 kgcm, these guillotine shears are ideal for various applications in sheet metal working. Specifications: - Manufacturer: WMW - Model: ScTP 3.15x2500 - Cutting force: 10 tons - Torque: 27,500 kgcm - Sheet thickness: 3.15 mm - Maximum material strength: 50 kg/mm² - Power consumption: 3.5 kW (see nameplate for more data) - With an impressive cutting force of 10 tons, the WMW ScTP 3.15x2500 effortlessly masters sheet thicknesses up to 3.15mm. - The crankplate shears deliver precise cuts that still meet the highest quality standards. - The robust construction and powerful torque make th ...

McIntyre 407 CAT Shear Designed to recover the precious metals found in Catalytic converters, JMC Cat shears also versatile enough to be used anywhere in your yard. Purpose Built McIntyre Cat shears have been purpose built for recovering precious metals from catalytic converters. The Catalytic converter is simply placed in the jaws and cut. The movement of the jaw is directly controlled by the moveable foot pedal and a V clamp holds the Cat in place during cutting. Once cut, the pinched end of the converter can be re-opened using the side bracket attached to the top jaw, allowing the contents to be poured out.

McIntyre 320 Shear The well established 320 Shear is a must for any yard and is now recognised as the industry standard for all shears of this type Powerful and high quality One of our most popular shears, the McIntyre 320 Shear has maintained dominance in a demanding market due to its strength, quality and reliability

: 28 min. Punching force: 110 to : 40x20 mm flat steel: 600x15 oder 400x20 mm L-beam 90°: 160x160x16 mm L-beam 45°: 70x70x7 mm : 50 mm square edge steel: 50 mm : 13 mm throat: 300 mm Basic equipment: - Complete set of blades for flat steel shears - Complete knife set for bar cutter - Complete knife set for angle steel shears - Compl. Standard punching device - Stamp quick release device for punches up to 40 mm diameter - Rectangle notch compl. with hold downs - Complete knife set below for rectangular notching - Upper tool for rectangular notching - Support table for flat material - Punching table with stop - Notch with stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

flat steel: 350 x 10 mm round bar steel: 35 mm square edge steel: 30 mm L-beam: 80x80x8 mm hole diameter in sheet thickness: Ø 27 in 13 bzw. Ø 20 in 8 mm : 500 kN throat: 177 mm : 34 (Hub 15mm) blade length: 356 mm engine output: 3.0 kW weight: 950 kg dimensions: 1300x1100x1850 mm Standard equipment: - Knife set for flat steel - Complete knife set for angle steel shears - Complete normal punching equipment - Quick release device for punches up to 31 mm - Support table for punching device, rectangular notching and flat steel shears - Bending stamp with matrices V 40 and V 70 - Electric contact stop (1.000 mm) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 32 /min Punching force: 60 to throat: 500 mm : 40x11 mm : 350x15 mm : 350x15 mm L-beam 90°: 120x120x10 mm : 45 mm square edge steel: 40 mm : 10 mm : Aufnahme bis max. 150x10 engine output: 5,5 kW weight: 2012 kg Basic equipment: - Flat steel shears with knife set - Angle shears with knife set - Punch with quick release device for punches up to 40 mm - Support table for punching device - Triangular notching device - Support table for notching - bending station - Bending stamp with matrices V 40 and V 70 - electrical contact stop (1 meter) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 32 /min Punching force: 60 to throat: 250 mm : bis max. Ø 40x11 mm : 350x15 mm : 350x15 mm L-beam 90°: 120x120x10 mm : 45 mm square edge steel: 40 mm : 10 mm : Aufnahme bis max. 150x10 engine output: 5,5 kW weight: ca. 1600 kg Basic equipment: - Flat steel shears with knife set - Angle shears with knife set - Punch with quick release device for punches up to 40 mm - Support table for punching device - Triangular notching device - Support table for notching - bending station - Bending stamp with matrices V 40 and V 70 - electrical contact stop (1 meter) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Punching force: 45 t hole diameter in sheet thickness: Ø 27x13 mm : 24 /min L-beam 90°: 80x80x8 mm L-beam 45°: 60x60x6 mm flat steel: 200x13 mm : 7 mm engine output: 2,2 kW weight: 760 kg Basic equipment: - Complete set of blades for flat steel shears - Complete knife set for angle steel shears - Compl. Standard punching device - Stamp quick release device for punches up to 27 mm diameter - Rectangular notching device compl. with hold down - notch - Support table for punching device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 10 mm Punching force: 55 to : 40x10 mm flat steel: 300x15 oder 200x20 mm L-beam 90°: 120x120x10 mm L-beam 45°: 70x70x7 mm : 40 mm square edge steel: 40 mm : 37 /min. throat: 250 mm weight of the machine ca.: 1.600 kg Basic equipment: - Complete set of blades for flat steel shears - Complete knife set for bar cutter - Complete knife set for angle steel shears - Compl. Standard punching device - Stamp quick release device for punches up to 40 mm diameter - Rectangle notch compl. with hold downs - Complete knife set below for rectangular notching - Upper tool for rectangular notching - Support table for flat material - Punching table with stop - Notch with stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 45 to. no. of strokes: 24 Hub/min hole diameter in sheet thickness: max. Ø 27 in 13 mm : 80x80x8 : 60x60x6 mm flat steel: 300x10/200x13 mm : 7 mm engine output: 2.2 kW range L-W-H: 1550x820x1540 mm weight: 760 kg Standard equipment: - Complete knife set for flat steel shears - complete knife set for angle steel shears - complete standard punching equipment - Stamp quick release device for punches up to Ø 27 mm - Rectangular notching device complete with hold-down device - notch - Support table for punching device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2100 mm plate thickness: 6,0 mm ST 42 thickness at Niro-steel: 4,0 mm VA cutting angle: 1,2 Grad no. of strokes: 28 Hub/min oil volume: 150 ltr. down holder: 11 Stück control: CYBELEC CybTouch engine output: 11,0 kW back stop - adjustable: 1.000 mm table height: 800 mm weight: 4.500 kg range L-W-H: 3.010 x 2.100 x 1.640 mm ------------------------------------------------- electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment ------------------------------------------------- Furnishing: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Quantity Cutting length limitation Material preselection, including sheet thickness Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) on ball screws ...

sheet width: 3100 mm plate thickness: 6,0 mm distance between columns: 3.100 mm down holder: 14 Stück no. of strokes: 16 - 24 Hub/min oil volume: 150 ltr. cutting angle: 0,5 - 1,5 ° thickness at Niro-steel: 4,0 mm column arm: 350 mm engine output: 11,0 kW weight of the machine ca.: 7.060 kg range L-W-H: 4100 x 2200 x 2190 mm -------------------------------------------------- electr. / hydraulic CNC guillotine shears - guided by a backdrop with CYBELEC CNC touch screen control with electr. / hydr. Cutting gap and cutting angle adjustment -------------------------------------------------- Furnishing: - CNC guiding guillotine shears - with electr. / hydr. Cutting gap and cutting angle adjustment - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including s ...

sheet width: 3100 mm plate thickness: 6,0 mm distance between columns: 3100 mm down holder: 14 Stück no. of strokes: 18 Hub/min oil volume: 150 ltr. cutting angle: 1,2 ° thickness at Niro-steel: 4,0 mm control: CYBELEC CybTouch weight: 6,3 To. range L-W-H: 4.000 x 2.100 x 1.640 mm -------------------------------------------------- electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment -------------------------------------------------- Furnishing: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including sheet thickness Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Can be folded up at max.travel, for ...