schneider tankbau used for sale

Diesel tank system - company filling station - consisting of: 1 x Storage container, 10.000 liter capacity, used 1 x fuel pump, type Eco 75, brand new Description container: according to DIN 6616-D, above ground, double-walled, incl. test certificate. The container has two saddle feet, a manhole with dome cover, is used, emptied inside and professionally cleaned and is equipped with the following fittings: 1 filling tube with TW closure (filling cap) and immersion tube, 1 sounding tube with dipstick and dipstick closure, 1 vent pipe with vent hood, 1 brand-new limit value transmitter with type approval (AIII), 1 ladder and 1 spare sleeve for removal purposes, 1 optical leak detector with type approval and leakage fluid. The container is reprimed and painted on the outside. (RAL sound). L = approx. 5.30 m - D = 1.60 m - weight approx. 2.4 to. - ex wo ...

Earth tank, storage tank, steel tank - brand new for the storage of HEL with 50,000 litres capacity, according to DIN 6608/2, double-walled, external with a high-quality PUR-ENDOPRENE insulation in accordance with DIN 6607. PUR-ENDOPENE is a 2-component solvent-free Polyurethane insulation with excellent insulation properties. Dimensions: D = 2.50 m - L = approx. 10.80 m - weight approx. 9.3 tons. Incl. a walk-in dome shaft, multi-part, according to DIN 6626, height-adjustable from approx. 850 mm to 1,050 mm, as well as a walk-in cover, galvanized + tagwaterproof. Containers ex works, freely charged. Additional price for a navigable dome shaft according to DIN 6626 General: You will receive an invoice with VAT shown. The purchase is made on our general terms and conditions. Further tank systems (new and used) as well as rental systems are also on offer ...

Diesel tank, storage tank, service station, tank plant, steel tank, storage tank with 10,000 litres of content according to DIN 6616/D, above ground, double-walled, incl. officially recognized test certificate. The container has two saddle feet, a manhole DN 500 with dome lid, is used, emptied inside and professionally cleaned and is equipped with the following fittings: 1 filling pipe with TW closure (filling cap) and immersion pipe, 1 bearing tube with bearing rod and bearing rod closure, 1 vent pipe with vent hood, 1 brand new limit sensor with type approval (AIII), 1 ladder and 1 spare sleeve for picking purposes, 1 optical leak detector with type approval and leakliquid. The container is re-primed and painted on the outside. Dimensions: L = approx. 5.30 m / D = 1.60 m / weight approx. 2.2 tons. / ex works, freely charged. General: You will r ...

Fuel oil tank, storage tank, steel tank, diesel tank, tank system with 60,000 litres capacity according to DIN 6616/D, above ground, double-walled, incl. officially recognized test certificate. The container has two saddle feet, a manhole DN 600 with dome lid, is used, cleaned, overhauled and equipped with the following fittings: 1 filling pipe with TW closure (filling cap) and immersion pipe, 1 bearing tube with bearing rod and bearing rod closure, 1 vent pipe with vent hood, 1 brand new limit sensor with type approval (AIII), 1 ladder and 1 spare sleeve for picking purposes, 1 optical leak detector with type approval and leakliquid. The container is re-primed on the outside and painted in ral 7011 - iron grey. Other colours at no extra charge: RAL 6005 - moss green, RAL 5011 - steel blue. L = approx. 12.80 m / D = 2.50 m / weight approx. 11.5 tons. ...

NEW Bainite model BMIM95 95 litre intermeshing type mixer Customs Tariff CN Code: 8477.8093 Manufacturer: Bainite Machines Pvt Ltd Net chamber volume: 95 litre Rotor speed: 6 - 60 rpm Rotor type: HP-5 design (intermeshing) Dust seals: SSA (self-sealing arrangement) Motor power: 420kW, 1000rpm AC motor, 3ph, 50Hz, 380/400V Discharge door: Hydraulic drop door with linear actuator and toggle latch. Two (2) J Type thermocouples mounted in door top as standard One (1) Single acting pneumatically operated oil injector Feed Hopper Assembly: Hydraulically operated Floating weight: single ?V? bottom type Gearbox: Full unidrive type with S.F. 2.25 Bedplate: Fabricated steel Ancillaries: Dust stop lubrication (1.5HP x 2), hydraulic pump unit (20HP) Three (3) Zone closed loop temperature control (TCU) Electrical Controls: Schneider make variable frequency drive (VFD) controls with ...

A good sample preparation in metallography (materialography) starts at the correct separation with a wett cutting machine. Good and proper separation prevents the burning and destruction of the material change in its structure and is the best way to save time and consumables. The separation is performed incorrectly is this very elaborate grinding and polishing extremely high overhead "punished"! Wet cutting machine cutting. Wet abrasive cutting | Separating SCHNEIDER METACUT 251 The head of the cutting grinding machine with built-in blade is lowered by a hand lever on the sample. METACUT 251 separating cutters are available exclusively in manual versions. This is usually not a disadvantage: the specimen geometry changes / separation task all the time, so can hinder the establishment of an automatic cut-off grinder. The workpiece is clamped at METACUT 251 - cut-off machines and the de ...

Granulator/granulator directly from stock available! Can be used in the cable processing and cable recycling, Kunstoffzerkleinerung and destruction of plastic and plastic parts Granulator/Schneidmühle type: RMH 16/22 VGA _ 4 KW drive power (further data see table) other granulator/granulator on request) RMH 16/22 VGA/power: 4 KW RMH granulator features: -In the RMH granulator RMH, a knife set is installed. -A sieve is fitted (drill holes on request.). -The following filter inserts are available standard production: 1.5 mm, 2 mm, 3 mm, 4 mm, 5 mm, 6 mm -V cutting geometry â Lenze electric motor / Schneider Electric box and breaker -Slight tilt of the filler funnel -Available with wheels/2 x fixed castors/2 x brake castors or adjustable rubber-mounted feet -With various trays available 1) Insert as box, here the material out of the box out can be tilted (2) slide ...

Made in Italy machine according to DIN 8606 Tip height: 260 mm Turning diameter over bed: 520 mm Swing over carriage: 300 mm Centre distance: 1500 mm Bed width: 400 mm Spindle bore: 82 mm Spindle nose: Camlock 8 " Spindle speeds: (24) 9-1600 rpm (option 11-2000 U/min) Engine output: 5.5 kW (option: 7.5 kW) feed Z-axis: (93) 0.028 6.43 mm / Rev Feed x axis: (93) 0.012 2.73 mm / Rev Thread, metric: (54) 0.5-224 mm Thread, Witworth: (55) 72 - 1/8 TPI Thread, module: (54) 0.5-112 mm Thread, Diametral Pitch: (54) 64 - 1/4 D.P.. Cross slide Lxw: 650 x 230 mm Transversal carriage stroke: 340 mm Upper carriage Lxw: 350 x 150 mm Upper carriage stroke: 150 mm Tailstock Quill diameter: 85 mm Tailstock Quill stroke: 200 mm Tailstock taper: MK 5 Weight: 3,100 kg Facilities: -Movement of the tailstock pneumatically supported -Acceptance Protocol according to DIN 8605, ...

Made in Italy machine according to DIN 8605: lathe with increased accuracy. Tip height: 215 mm Turning diameter over bed: 430 mm Swing over carriage: 240 mm Top width: 1,000 mm Bed width: 290 mm Spindle bore: 52 mm Spindle nose: Camlock 6 " Spindle speeds variable: 6 Spindle speeds: 60-2,000 rpm S6/S1 engine power: 4 kW (option: 5.5 kW) feed Z-axis: (38) 0.05 - 1.88 mm / Rev Feed x axis: (38) 0.02 1,084 mm / Rev Thread cutting, metric: (30) 0.45-20 mm Thread cutting, Witworth: (35) 80-1 3/4 TPI Thread cutting, module: (25) 0.25-10 mm Thread cutting, Diametral Pitch: (30) 160-3 1/2 D.P.. Cross slide Lxw: 370 x 190 mm Transversal carriage stroke: 240 mm Upper carriage Lxw: 275 x 115 mm Upper carriage stroke: 120 mm Tailstock Quill diameter: 60 mm Tailstock Quill stroke: 135 mm Tailstock taper: MK 4 Weight: approx. 2,000 kg Facilities: -Infinitely variable  ...

Many thanks for your interest on our second hand machines, please find follow our offer: manufacturer: Bindler & Schneider Type: ZE 90/10-10-F/SL (Gear pump) Year of manufacturing: unbekannt output capacity: 6000 kg /h pieces: 1 different: guter Zustand I offer this machine in as-is where-is condition ex Warehouse Hess. Lichtenau, unpacked

Made in Italy Peak: 300 mm Rotary diameter over bed: 600 mm Rotary diameter via sled: 380 mm Peak: 1,500 mm Bed width: 400 mm Spindle bore: 82 mm Spindle nose: Camlock 8 " Spindle speeds: (12) 16-1200 U/min Engine power: 9.2 kW (special equipment/standard: 7.5 kW) Reprimor Z-axis: (93) 0.028-6.43 mm/U Feed X-axis: (93) 0.012-2.73 mm/U Thread, metric: (54) 0.5-224 mm Threads, Witworth: (55) 72-1/4 x8 TPI Thread, module: (54) 0.5-112 mm Threads, Diametral Pitch: (54) 64 -1/4 D.P. Crossleigh hub: 340 mm Oberslitten hub: 150 mm Riding stock pinol diameter: 85 mm Riding stove pinol stroke: 200 mm Ridstock cone: MK 5 Weight: About 3,200 kg Facilities: -3-axis digital display -Step-by-step speed adjustment -Automatic lubrication of the management railways -LED lighting -Micrometer bed strike -9.2 kW engine instead of 7.5 kW -Quick change holder system mul ...

The laser WUXI CHEERON QY-LC1500-2540 FIBER was produced in 2020 by the brand Wuxi Cheeron Qingyuan Laser Technology Co. The machine is new, it was only included for a test run after the purchase. The machine uses an IPG Photonics (Germany) laser source. The 3-axis fiber optic laser cutter has a power of 1500 W and a large working area of ​​4000 x 2500 mm. The modern design of the laser guarantees many processing possibilities, thanks to the fact that it is equipped with two automatic sheet metal loading tables, a cutting chamber, a large LCD screen, and extensive equipment. Laser technical parameters: - two automatic feeding tables: 4000 x 2500 mm - cutting working surface: 4000 x 2500 mm - closed, illuminated cutting chamber, with strong gas extraction - HD cameras for viewing in the cutting chamber and external viewing of loading tables - a closed container with a control  ...

VESPA 30/60/18.5 VGA Cutting mill for plastics 18.5 KW, 200-300 kg/h. Insertion opening mm: 620×400 Rotor diameter mm: 300 Throughput kg/h: 200-300 Rotor blade quantity/mm: 6 x 300 Stator knife quantity/mm: 4 x 300 Engine KW: 18,5 Dimensions mm: 1210×1000×1925 Weight kg: 1500 options: Material conveying blower 4.0 kW and Big Bag filling station. Soundproofing can also be ordered at an additional cost. VESPA Granulators for Plastics – Soundproof insertion opening for minimal noise level and easy feeding with multiple alternative feed options – Horizontally or diagonally separated housing with robust welded steel construction – The cutting rotor rotates in an extremely robust self-aligning roller bearing, which is arranged in the bearing housing outside the cutting chamber. – Easy access to the knives. Knife made of high-quality tool steel with pre ...

VESPA 45/80/37 kWt VGA Cutting mill for plastics 37 KW, 400-700 kg. Model VESPA 45/80/37 kWt VGA Throughput Kg/h: 400-700 Rotor diameter мм: 450 Rotor knife quantity/dimensions piece x mm: 6×400 Stator Knife Quantity/Dimensions Piece x mm: 4×400 Engine kW: 37 Weight Kg: 2300 VESPA Granulators for Plastics – Soundproof insertion opening for minimal noise level and easy feeding with multiple alternative feed options – Horizontally or diagonally separated housing with robust welded steel construction – The cutting rotor rotates in an extremely robust self-aligning roller bearing, which is arranged in the bearing housing outside the cutting chamber. – Easy access to the knives. Knife made of high-quality tool steel with precision machining and surface finish – Good accessibility for cleaning and maintenance – Electrical equipment with SCHNEIDER ELEC ...

VESPA 35/50/15 VGA Cutting mill for plastics 15 KW, 150-250 kg/h. Insertion opening mm: 520×380 Rotor diameter mm: 350 Throughput kg/h: 150-250 Rotor blade quantity/mm: 6 x 250 Stator knife quantity/mm: 4 x 250 Motor KW: 15,0 Dimensions mm: 1180x880x1970 Weight kg: 1150 options: With material conveying blower 4.0 kW and big bag filling station. Soundproofing can also be ordered at an additional cost. Information on throughput quantities is indicative and depends on the type of material, shape, temperature, feed method, rotor configuration, blade sharpness, sieve size, etc. VESPA Granulators for Plastics – Soundproof insertion opening for minimal noise level and easy feeding with multiple alternative feed options – Horizontally or diagonally separated housing with robust welded steel construction – The cutting rotor rotates in an extremely robust self ...

Pester PEWO-fold 1 overwrapping machine for single cartons and carton collations, in OPP-, PVC-, PE-materials, with foil width from 90 mm to 300 mm, film thickness from 0.02 mm to 0.05 mm, maximum roll diameter 350 mm. Size range min. 60 x 60 x 20 mm, max. 400 x 350 x 140 mm, Machine controlled using ELAU/Schneider PacDrive, Electrical connection 3x400V, V+N+PE/50-60 Hz, connected load 5.2 kW/12.5A, Operating pressure 4 bar, compressed air 4 to 10 bar. Infeed height approx. 900 mm, outfeed height approx. 900-950 mm. Output up to 60 cycles/collations per minute. Includes: Infeed conveyor, 1100 mm long x 260 mm belt width, outfeed conveyor, 2000 mm long x 260 mm belt width, Alpha Compact labeller, PEWO-collect collating table, miscellaneous sets of format parts

1015 KW Dresser counterpressure steam turbine for sale. 35.000 € plus VAT FCA freely charged in D-Bergisch Gladbach. TUBRINE Brand: DRESSER-RAND (Nadrowski) Type: AVT 72 TW 17 Number: 16225-1 Electr. Power: 1015 KW Rated power: 1375 kVA Year of construction: 1995 (control units upgraded in 2008) Voltage: 400 V RPM: 1500 rpm Steam flow rate: 25 tons /h Dimensions (l x w x h): 4.50 x 2.40 x 2.30 m Inlet temperature: 253°C Inlet pressure : 18 bar Exhaust temperature : 152°C Outlet pressure : 5.0 bar Steam flow rate at the entrance: 25 tons/h Turbine weight: 11,000 kg Generator Brand: Leroy Somer Type: NWR 50 BL10-4P Electrical power : 1015 KW SWITCHBOARD Manufactured by TIL SA and updated in 2008 Schneider control

table diameter: 1500 mm table load: 5 t swivelling range: 0 - 130 Grad turning speeds: 0,05 - 0,5 U/min : 10000 Nm 0: 1,5 / 1,5 kW welding current: 700 Ampere • Self-locking gear, therefore no forward and backward at eccentric load. • Electronic components from Schneider, Siemens and Delta. • Frequency-controlled stepless speed of the turntable. • High stability due to the robust construction. • welding power transmission • CE certificate. • Very good price / quality ratio. • The D-HBE series comes as a standard version with a cable remote control and delivered with a footswitch. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 900 mm table load: 1,0 t swivelling range: 135 Grad turning speeds: 0,12 - 1,2 U/min : 820 mm welding current: 500 Ampere total power requirement: 0,75 + 0,55 kW weight of the machine ca.: 1,1 t dimensions of the machine ca.: 1,5 x 1,0 x 0,9 m • Self-locking gear, therefore no forward and backward at eccentric Load. • Electronic components from Schneider, Siemens and Delta. • Frequency-controlled stepless speed of the turntable. • High stability due to the robust construction. • welding power transmission • CE certificate. • Very good price / quality ratio. • The D-HBE series comes as a standard version with a cable remote control and delivered with a footswitch. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 1200 mm table load: 1,2 t swivelling range: 0 - 120 Grad turning speeds: 0,06-0,6 U/min max. torque on the faceplate: 2400 Nm table pass: 200 mm welding current: 500 Ampere total power requirement: 0,75 + 1,1 kW weight of the machine ca.: 1,0 t ELDING TABLE WITH LARGE THROUGH BORE • Self-locking gearbox, no pre- or after-run with eccentric load. • Electronic components from Siemens and Schneider. • Frequency-controlled, very accurate speed control. • Turntable with large through hole and T-slots. • High stability through a clever construction. • CE certificate. • Very good price / quality ratio. • The D-TLP series comes with remote control and foot pedal (left / right). No original pictures. Design but identical. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 1000 mm table load: 0,6 t swivelling range: 0 - 90 Grad turning speeds: 0,1 - 1,25 U/min max. torque on the faceplate: 900 Nm table pass: 200 mm welding current: 500 Ampere total power requirement: 0,37 + 0,75 kW weight of the machine ca.: t ELDING TABLE WITH LARGE THROUGH BORE • Self-locking gearbox, no pre- or after-run with eccentric load. • Electronic components from Siemens and Schneider. • Frequency-controlled, very accurate speed control. • Turntable with large through hole and T-slots. • High stability through a clever construction. • CE certificate. • Very good price / quality ratio. • The D-TLP series comes with remote control and foot pedal (left / right). No original pictures. Design but identical. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Fill 3D-Ultrasonic Cutter Here we offer you a Fill 3D ultrasonic cutting system. Fill 3D-ULTRASONIC SCHNEIDER 3D ULTRASONIC CUTTER The 3D ultrasonic cutter from Fill enables three-dimensional contour cutting of fiber-reinforced plastics using ultrasonically excited cutting systems. Your advantages: Ergonomic feeding and unloading Easy creation of bleed programs (NC control) Space-saving system concept (as an alternative to the robot) High repeatability High process stability Easy and fast tool change Possible integration into an overall process chain The principle: The linear axis portal enables precise guidance of the ultrasonic knife with a small footprint and simple kinematics. Thanks to the Siemens 840 D CNC control, the trimming device can be programmed like a machine tool. Tool corrections or path changes can simply be carried out directly on the machine. As standa ...

table diameter: 1000 mm table load: 1200 Kg swivelling range: 0 - 135 Grad turning speeds: 0,1 - 1,0 U/min height adjustment: 1000 - 1450 mm max. torque on the faceplate: 2000 Nm engine output: 0,75 / 0,55 kW welding current: 500 Ampere - Manual height adjustment. - Self-locking gearbox, therefore hardly any pre and after-run at eccentric Load. - Electronic components from Schneider, Siemens and Delta. - Frequency-controlled, stepless speed of the turntable. - High stability due to the robust construction. - CE certificate. The D-HBE series comes as a standard version with a cable remote control and a footswitch. Welding power transmission for max.500Ampere. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 560 mm table load: 0,3 t swivelling range: 0 - 90 Grad turning speeds: 0,25 - 4,0 U/min : 360 Nm welding current: 500 Ampere total power requirement: 0,4 / Hand kW • Self-locking gear, therefore no forward and backward at eccentric Load. • Electronic components from Schneider, Siemens and Delta. • Frequency-controlled stepless speed of the turntable. • High stability due to the robust construction. • welding power transmission • CE certificate. • Very good price / quality ratio. • The D-HBE series comes as a standard version with a cable remote control and delivered with a footswitch. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 1500 mm table load: 5000 Kg swivelling range: 0 - 130 Grad turning speeds: 0,05 - 0,5 U/min height adjustment: 1300 - 2050 mm max. torque on the faceplate: 10000 Nm engine output: 1,5 / 1,5 kW welding current: 1000 Ampere - Manual height adjustment. - Self-locking gearbox, therefore hardly any pre and after-run at eccentric Load. - Electronic components from Schneider, Siemens and Delta. - Frequency-controlled, stepless speed of the turntable. - High stability due to the robust construction. - CE certificate. The D-HBE series comes as a standard version with a cable remote control and a footswitch. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 1400 mm table load: 2,0 t swivelling range: 0 - 135 Grad turning speeds: 0,05 - 0,5 U/min max. torque on the faceplate: 6000 Nm table pass: 200 mm welding current: 700 Ampere total power requirement: 1,1 + 2,2 kW weight of the machine ca.: t ELDING TABLE WITH LARGE THROUGH BORE • Self-locking gearbox, no pre- or after-run with eccentric load. • Electronic components from Siemens and Schneider. • Frequency-controlled, very accurate speed control. • Turntable with large through hole and T-slots. • High stability through a clever construction. • CE certificate. • Very good price / quality ratio. • The D-TLP series comes with remote control and foot pedal (left / right). The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 1600 mm table load: 6 t swivelling range: 0 - 130 Grad turning speeds: 0,05 - 0,5 U/min : 12000 Nm 0: 1,5 / 2,2 kW welding current: 700 Ampere • Self-locking gear, therefore no forward and backward at eccentric load. • Electronic components from Schneider, Siemens and Delta. • Frequency-controlled stepless speed of the turntable. • High stability due to the robust construction. • welding power transmission • CE certificate. • Very good price / quality ratio. • The D-HBE series comes as a standard version with a cable remote control and delivered with a footswitch. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Table dimensions: 800 x 800 mm table load: 1500 Kg swivelling range: 0 - 105 Grad turning speeds: 0,15 - 1 U/min height adjustment: 672 - 1180 mm hollow spindle diameter: mm welding current: 500 Ampere max. torque on the faceplate: 3000 Nm total power requirement: 0,75 kW dimensions of the machine ca.: 1560x1120x750 m Characteristics: • Made in EU • Self-locking gear, therefore no leading and trailing at eccentric load • Hydraulic height adjustment allows almost limitless positioning • Electronic quality components from Schneider / Siemens / Delta • Frequency-controlled stepless speed of the turntable • High stability through a heavy and compact design • CE certificate • Very good value for money • Standard version comes with remote control and dual foot pedal • 3 years warranty (see warranty conditions) • Hydraulically height adjustable with locking system (for fal ...

table diameter: 700 mm table load: 0,6 t swivelling range: 0 - 90 Grad turning speeds: 0,2 - 2,0 U/min : 900 Nm total power requirement: 0,37 / 0,37 kW • Self-locking gear, therefore no forward and backward at eccentric Load. • Electronic components from Schneider, Siemens and Delta. • Frequency-controlled stepless speed of the turntable. • High stability due to the robust construction. • welding power transmission • CE certificate. • Very good price / quality ratio. • The D-HBE series comes as a standard version with a cable remote control and delivered with a footswitch. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 1500 mm table load: 5,0 t swivelling range: 0 - 135 Grad turning speeds: 0,05 - 0,5 U/min max. torque on the faceplate: 10000 Nm table pass: 200 mm welding current: 700 Ampere total power requirement: 1,5 + 3,0 kW weight of the machine ca.: t ELDING TABLE WITH LARGE THROUGH BORE • Self-locking gearbox, no pre- or after-run with eccentric load. • Electronic components from Siemens and Schneider. • Frequency-controlled, very accurate speed control. • Turntable with large through hole and T-slots. • High stability through a clever construction. • CE certificate. • Very good price / quality ratio. • The D-TLP series comes with remote control and foot pedal (left / right). No original pictures. Design but identical. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 30 t throat: 200 mm stroke: 0 - 60 mm table:: 400 x 600 mm table:: 150 mm - Bohrung no. of strokes: 140 Hub/min bore: 40,0 mm - Werkzeug compressed air: max. 6,0 bar dayligth: 300 mm total power requirement: 3,0 kW weight: 1.670 kg range L-W-H: 1150 x 1350 x 2050 mm Furnishing: - Welded steel structure body frame - AISI 4140 (42CrMo4) alloy steel crankshaft - CNC ground for maximum precision SnBz-12 quality - Bronze bearings, ground for minimal surface resistance - 4 sides pneumatic clutch-brake combination - PLC control for safety (PILZ Germany) - Photo cell light barriers around the work table (PILZ Germany) - Two-hand and foot pedal control - Adjustable stroke - Central lubrication system - CE safety approval by TÜV - electrical equipment SIEMENS, SCHNEIDER, PHOENIX, OMRON The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 1400 mm table load: 3,0 t swivelling range: 0 - 135 Grad turning speeds: 0,05 - 0,5 U/min max. torque on the faceplate: 6000 Nm table pass: 200 mm welding current: 700 Ampere total power requirement: 1,1 + 2,2 kW weight of the machine ca.: t ELDING TABLE WITH LARGE THROUGH BORE • Self-locking gearbox, no pre- or after-run with eccentric load. • Electronic components from Siemens and Schneider. • Frequency-controlled, very accurate speed control. • Turntable with large through hole and T-slots. • High stability through a clever construction. • CE certificate. • Very good price / quality ratio. • The D-TLP series comes with remote control and foot pedal (left / right). No original pictures. Design but identical. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 600 mm table load: 0,6 t swivelling range: 0 - 90 Grad turning speeds: 0,1 - 1,8 U/min max. torque on the faceplate: 450 Nm table pass: 80 mm welding current: 500 Ampere total power requirement: 0,18 + 0,18 kW weight of the machine ca.: t ELDING TABLE WITH LARGE THROUGH BORE • Self-locking gearbox, no pre- or after-run with eccentric load. • Electronic components from Siemens and Schneider. • Frequency-controlled, very accurate speed control. • Turntable with large through hole and T-slots. • High stability through a clever construction. • CE certificate. • Very good price / quality ratio. • The D-TLP series comes with remote control and foot pedal (left / right). No original pictures. Design but identical. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dear Sir or Madam, for you in the offer : Granulator/cutting machine available directly from stock! Can be used in cable processing/cable recycling, plastic shredding and destruction of plastic and plastic parts Granulator/Granulator/Granulator Type: RMH 16/22 VGA _ 4 KW Drive Power (See table for more data) Other granulator/cutting machine on request) RMH 16/22 VGA/drive power: 4 KW Features RMH Granulator: - A knife set is installed in the RMH Granulator RMH. - A sieve insert is installed (perforation as desired.). - The following screen inserts are available in stock: 1.5 mm, 2 mm, 3 mm, 4 mm, 5 mm, 6 mm - V- Section Geometry - Lenze Electric Motor / Schneider Electric Box and Circuit Breaker - Easy tilting of the filling hopper - Available with wheels/2 x fixed castors/2 x brake rollers or adjustable rubber-mounted feet - Available with different bays 1) ...

table diameter: 800 mm table load: 600 Kg swivelling range: 0 - 135 Grad turning speeds: 0,1 - 2,0 U/min height adjustment: 850 - 1300 mm max. torque on the faceplate: 900 Nm engine output: 0,37 / 0,37 kW welding current: 500 Ampere - Manual height adjustment. - Self-locking gearbox, therefore hardly any pre and after-run at eccentric Load. - Electronic components from Schneider, Siemens and Delta. - Frequency-controlled, stepless speed of the turntable. - High stability due to the robust construction. - CE certificate. The D-HBE series comes as a standard version with a cable remote control and a footswitch. Welding power transmission for max.500Ampere. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 1100 mm table load: 2 t swivelling range: 0 - 135 Grad turning speeds: 0,1 - 1,0 U/min : 4000 Nm 0: 1,1 / 0,75 kW welding current: 500 Ampere • Self-locking gear, therefore no forward and backward at eccentric Load. • Electronic components from Schneider, Siemens and Delta. • Frequency-controlled stepless speed of the turntable. • High stability due to the robust construction. • welding power transmission • CE certificate. • Very good price / quality ratio. • The D-HBE series comes as a standard version with a cable remote control and delivered with a footswitch. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 1300 mm table load: 3 t swivelling range: 0 - 130 Grad turning speeds: 0,05 - 0,5 U/min : 6000 Nm 0: 1,1 / 1,1 kW welding current: 700 Ampere • Self-locking gear, therefore no forward and backward at eccentric load. • Electronic components from Schneider, Siemens and Delta. • Frequency-controlled stepless speed of the turntable. • High stability due to the robust construction. • welding power transmission • CE certificate. • Very good price / quality ratio. • The D-HBE series comes as a standard version with a cable remote control and delivered with a footswitch. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 1100 mm table load: 2000 Kg swivelling range: 0 - 135 Grad turning speeds: 0,1 - 1,0 U/min height adjustment: 1100 - 1550 mm max. torque on the faceplate: 4000 Nm engine output: 1,1 / 0,75 kW welding current: 500 Ampere - Manual height adjustment. - Self-locking gearbox, therefore hardly any pre and after-run at eccentric Load. - Electronic components from Schneider, Siemens and Delta. - Frequency-controlled, stepless speed of the turntable. - High stability due to the robust construction. - CE certificate. The D-HBE series comes as a standard version with a cable remote control and a footswitch. Welding power transmission for max.500Ampere. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

+ + + Availability / Delivery time / Pre-order + + + The non-binding estimated delivery time is approx. 3-5 months (+/-) (Provided that there are no unforeseeable delays or supply bottlenecks in between) --> A pre-order can be placed. - - - - - Net price: 2.150 € (excl. VAT) gross price: €2,558.50 (incl. VAT) - - - - - PTO generator 18 kVA with AVR -> More models with 18 - 80 kVA can be found in our other displays - - - - - Data of the PTO generator: - Power: 18 kVA - Voltage: 230 / 400 volts - AVR ESC - Dimensions: 95 x 80 cm - Weight: 134 kg - - - - - Digital Display: - Volt - Display (V) - Ampere - Display (A) - Hertz - Display (Hz) - Power in kVA - Operating hours - Meters - - - - - Requirements for the tractor: - PTO speed: 428 rpm - Recommended tractor power: 40 - 50 hp - - - - - Sockets: - 1x 400V 32A - 2x 1-phase socket 16A ...

table diameter: 1400 mm table load: 4 t swivelling range: 0 - 130 Grad turning speeds: 0,05 - 0,5 U/min : 8000 Nm 0: 1,1 / 1,5 kW welding current: 700 Ampere • Self-locking gear, therefore no forward and backward at eccentric load. • Electronic components from Schneider, Siemens and Delta. • Frequency-controlled stepless speed of the turntable. • High stability due to the robust construction. • welding power transmission • CE certificate. • Very good price / quality ratio. • The D-HBE series comes as a standard version with a cable remote control and delivered with a footswitch. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 2000 mm table load: 10000 Kg swivelling range: 0 - 130 Grad turning speeds: 0,02 - 0,2 U/min height adjustment: 1450 - 2200 mm max. torque on the faceplate: 20000 Nm engine output: 1,5 / 2,0 kW welding current: 1000 Ampere - Manual height adjustment. - Self-locking gearbox, therefore hardly any pre and after-run at eccentric Load. - Electronic components from Schneider, Siemens and Delta. - Frequency-controlled, stepless speed of the turntable. - High stability due to the robust construction. - CE certificate. The D-HBE series comes as a standard version with a cable remote control and a footswitch. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 2000 mm table load: 10,0 t swivelling range: 0 - 135 Grad turning speeds: 0,05 - 0,5 U/min max. torque on the faceplate: 20000 Nm table pass: 200 mm welding current: 1000 Ampere total power requirement: 3,0 + 4,0 kW weight of the machine ca.: t ELDING TABLE WITH LARGE THROUGH BORE • Self-locking gearbox, no pre- or after-run with eccentric load. • Electronic components from Siemens and Schneider. • Frequency-controlled, very accurate speed control. • Turntable with large through hole and T-slots. • High stability through a clever construction. • CE certificate. • Very good price / quality ratio. • The D-TLP series comes with remote control and foot pedal (left / right). No original pictures. Design but identical. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 1300 mm table load: 3000 Kg swivelling range: 0 - 130 Grad turning speeds: 0,05 - 0,5 U/min height adjustment: 1200 - 1800 mm max. torque on the faceplate: 6000 Nm engine output: 1,1 / 1,1 kW welding current: 700 Ampere - Manual height adjustment. - Self-locking gearbox, therefore hardly any pre and after-run at eccentric Load. - Electronic components from Schneider, Siemens and Delta. - Frequency-controlled, stepless speed of the turntable. - High stability due to the robust construction. - CE certificate. The D-HBE series comes as a standard version with a cable remote control and a footswitch. Welding power transmission for max.500Ampere. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

+ + + Availability / Delivery time / Pre-order + + + The non-binding estimated delivery time is approx. 3-5 months (+/-) (Provided that there are no unforeseeable delays or supply bottlenecks in between) --> A pre-order can be placed. - - - - - Net price: 2.400 € (excl. VAT) gross price: €2,856 (incl. VAT) - - - - - PTO generator 22 kVA with AVR -> More models with 18 - 80 kVA can be found in our other displays - - - - - Data of the PTO generator: - Power: 22 kVA - Voltage: 230 / 400 volts - AVR ESC - Dimensions: 95 x 80 cm - Weight: 134 kg - - - - - Digital Display: - Volt - Display (V) - Ampere - Display (A) - Hertz - Display (Hz) - Power in kVA - Operating hours - Meters - - - - - Requirements for the tractor: - PTO speed: 428 rpm - Recommended tractor power: 50 - 60 hp - - - - - Sockets: - 1x 400V 32A - 2x 1-phase socket 16A  ...

+ + + Availability / Delivery time / Pre-order + + + The non-binding estimated delivery time is approx. 3-5 months (+/-) (Provided that there are no unforeseeable delays or supply bottlenecks in between) --> A pre-order can be placed. - - - - - Net price: 2.750 € (excl. VAT) gross price: €3,272.50 (incl. VAT) - - - - - PTO generator 27 kVA with AVR -> More models with 18 - 80 kVA can be found in our other displays - - - - - Data of the PTO generator: - Power: 27 kVA - Voltage: 230 / 400 volts - AVR ESC - Dimensions: 95 x 80 cm - Weight: 147 kg - - - - - Digital Display: - Volt - Display (V) - Ampere - Display (A) - Hertz - Display (Hz) - Power in kVA - Operating hours - Meters - - - - - Requirements for the tractor: - PTO speed: 428 rpm - Recommended tractor power: 50 - 60 hp - - - - - Sockets: - 1x 400V 63A - 2x 1-phase socket 1 ...

table diameter: 2500 mm table load: 20,0 t swivelling range: 0 - 135 Grad turning speeds: 0,04 - 0,4 U/min max. torque on the faceplate: 40000 Nm table pass: 200 mm welding current: 1000 Ampere total power requirement: 5,5 + 11,0 kW weight of the machine ca.: t ELDING TABLE WITH LARGE THROUGH BORE • Self-locking gearbox, no pre- or after-run with eccentric load. • Electronic components from Siemens and Schneider. • Frequency-controlled, very accurate speed control. • Turntable with large through hole and T-slots. • High stability through a clever construction. • CE certificate. • Very good price / quality ratio. • The D-TLP series comes with remote control and foot pedal (left / right). No original pictures. Design but identical. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2540 mm plate thickness: 4,5 mm ST thickness at Niro-steel: 3,0 mm VA bending angle max.: 0 - 135 ° daylight opening: 100 mm back stop - adjustable: 70 - 600 mm total power requirement: 5,5 kW weight of the machine ca.: 6275 kg dimensions of the machine ca.: 3900 x 1700 x 1900 mm Description . - Full hardened structure - BEIJER 7 ”touch screen control Software with 40 programs and up to 50 steps 7-inch touchscreen built into the side stand - with manual backgauge, adjustable from behind - Electronic components are quality components from SCHNEIDER - electrical cabinet is integrated in the side stand - Adjustment of the hydraulic pressure to the material thickness - Adjustment of the material thickness on the bending beam is easy with a mm scale - Handle for adjusting the material thickness on the upper beam is hidden in the side stand - Segmented upper cheek The dat ...

sheet width: 2035 mm plate thickness: 4,5 mm ST thickness at Niro-steel: 3,0 mm VA bending angle max.: 0 - 135 ° daylight opening: 100 mm back stop - adjustable: 70 - 600 mm total power requirement: 5,5 kW weight of the machine ca.: 4145 kg dimensions of the machine ca.: 3300 x 1550 x 1900 mm Description . - Full hardened structure - BEIJER 7 ”touch screen control Software with 40 programs and up to 50 steps 7-inch touchscreen built into the side stand - with manual backgauge, adjustable from behind - Electronic components are quality components from SCHNEIDER - electrical cabinet is integrated in the side stand - Adjustment of the hydraulic pressure to the material thickness - Adjustment of the material thickness on the bending beam is easy with a mm scale - Handle for adjusting the material thickness on the upper beam is hidden in the side stand - Segmented upper cheek The dat ...

+ + + Availability / Delivery time / Pre-order + + + The non-binding estimated delivery time is approx. 3-5 months (+/-) (Provided that there are no unforeseeable delays or supply bottlenecks in between) --> A pre-order can be placed. - - - - - Net price: 3.150 € (excl. VAT) gross price: €3,748.50 (incl. VAT) - - - - - PTO generator 38 kVA with AVR -> More models with 18 - 80 kVA can be found in our other displays - - - - - Data of the PTO generator: - Power: 38 kVA - Voltage: 230 / 400 volts - AVR ESC - Dimensions: 95 x 80 cm - Weight: 179 kg - - - - - Digital Display: - Volt - Display (V) - Ampere - Display (A) - Hertz - Display (Hz) - Power in kVA - Operating hours - Meters - - - - - Requirements for the tractor: - PTO speed: 428 rpm - Recommended tractor power: 90 - 100 hp - - - - - Sockets: - 1x 400V 63A - 2x 1-phase socket  ...