rubber press used for sale

clamping force: 4.500 kN injection volume: 3.300 cm³ screw diameter: -- mm platen size: 670 x 780 mm Condition: second-hand, Specification: rubber injection moulding machine - second-hand EUROMAP size 4000 – 7000 Clamping unit: - Clamping unit: vertical - Clamping force: 4500 kN - Platen size: 670 x 780 mm - Max. stroke: 600 mm (see data sheet) Injection unit: - Max. injection volume: 3,300 cm³ - Injection pressure: 2150 bar - Power supply: 3x 400 V, 50 Hz, N - Motor power: 35,5 kW - Installed heating capacity: 73,9 kW - Weight: Clamping unit approx.: 8,400 kg Injection unit approx.: 2,700 kg Hydraulic unit with oil and control cabinet 2,200 kg Additional equipment (approx.): 3,000 kg Total weight approx.: 16.300 kg - For dimensions, see the installation data in the appe ...

clamping force: 4.500 kN injection volume: 5.600 cm³ screw diameter: 610 - 985 mm platen size: 670 x 780 mm Condition: second-hand, Specification: rubber injection moulding machine - second-hand EUROMAP size 4500 – 12300 Clamping unit: - Clamping unit: vertical - Clamping force: 4500 kN - Platen size: 670 x 780 mm - Max. stroke: 610 - 985 mm (see data sheet) Injection unit: - Injection unit type: ADV - Max. injection volume: 5,600 cm³ - Injection pressure: 2200 bar - Power supply: 3x 400 V, 50 Hz, N, PE - Pump capacity: 27 kW - Weight: Cutting unit approx.: 10,200 kg Injection unit approx.: 3,500 kg Hydraulic unit with oil: 2,600 kg Accessories approx.: 4,700 kg Total weight approx.: 21,000 kg - For dimensions, see the installation data in the appendix The data for this ad w ...

Rubber buffers / silent blocs for concrete block machines Brands: SCHLOSSER, Hess, Masa, Omag, Rekers, Frima, Techmatic Web: contec-ek

1 x Francis Shaw 45mm dia coldfeed rubber extruder, M/c no. 4513, Year: 1992, power roll feed, L/D ratio 15:1, hinged straight head with c\clamp, cored scred + jacketed barrel with built in temp control unit. Complete with control panel and in very good condition. Box of dies included.

Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.

Used rubber extruder make Troester, type GSV 60/k-12-18D-m.S., Execution as desired, with or without vacuum Built in 1991, machine was in operation until the beginning of 2010 Feed roller Kpl. new drive with flat gear motor Screw speed max. 62 rpm. Engine power 22 kW Control with PLC and temperature control new on request Extruder similar to attached photos.

Used Troester rubber extruder type GSV 60/k-12-18 D with feed roll can be modified/overhauled according to customer\s specification, with or without vacuum, year of construction: 1991 machine was in operation until end of 2010. including feed roll, new drive with flat-gear motor screw speed: maximum 62 rpm motor power: 22 kW PLC control and TCU can be renewed, if requested.

Knife Drawing No. 05714-223C1

Iddon HRX 4.5? (120mm) Cold Feed Rubber Extruder Year 1994 LD ratio 17:1 Bostock & Bramley Gearbox ABB Motor: 1994, 95kW, 1870 rpm, 419 amps, 360 volts With 1 x spare vacuum screw With Control Panel

1 x Alpha Technologies Mooney MV2000e Viscometer software discs and operation manual are included. You will have to register the software. PC not available. In good condition.

Francis Shaw 90mm coldfeed rubber extruder.Year: 1992. Machine No.4846Vented. Side power roller feed,L/D ratio 20:1,H series David Brown gearbox,Thrige Scott 63kW, 2000rpm DC variable speed motor.Machine fully overhauled, cleaned/painted and fitted with NEW electrical control panel. With provision for 5 x TCU's.

1 x Berstorff GmbH 250mm strainer extruder, Year of manufacture: 1988, L/D ratio 7:1, power roller feed (300mm wide), with 120kW, 1800rpm DC variable speed motor mounted on top of gearbox (belt drive), with tube head and knife at top for sheet extrusion. Complete with control panel etc and in very good condition.

1 x Farrel Bridge Model BR lab banbury mixer, Serial no. 91M7000, year: April 1991, Chamber volume 1.5litre pneumatic hopper and swing side discharge door, David Brown gearbox, 30kW DC variable speed motor and controls. Fully guarded with Key interlock system. Complete and in excellent condition.

Tyre testing machine - static balancer for passenger tyres. Tyre size from 15 "to 18" (20") CE certified More details see the attached description!

Mesh belt for AUMA / Rotocure new and unused Length: 14100mm Width: 2250mm

Berstorff Rotocure AUMA 20-S Drum dia: 2000mm Drum width: 2600mm Sandvic Steelbelt Description attached!

Guided from bronze Drawing No. 05714 -227D1

Key data: 70

Single-screw rubber extruder with feed roller and degassing in screws of 70mm and a process length of 22.D - with two-speed temperature-controlled entagling screw - Degassing cylinder with device for static and/or vacuum degassing of the material - a vacuum block pump - two water temperature control units with 9kW heating capacity each, - a Siemens SPS S7 machine with Siemens KTP1200 HMI control panel - a directly driven feed roller feeder for rubber raw strips, a funnel-material stiffening system with Strip monitoring - temperable base body for tool holder and v.m

available Troester Triplex Extruder Top machine QSM 90x 16D Middle machine 200W x 6D Below machine QSM 150 x 16D Head MW500 Description attached!

Farrel Twin Screw / Rollerdie Extruder complete available with Motor and Inverter Description attached!

screw ø:: 120 mm screw length:: 17D screw speedl:: 42 U/min drive power:: 138 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: -- mm cross-section heigth:: -- mm feed:: -- mm speed of feed:: 0,4 - 20 m/min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: 85 mm cross-section heigth:: 25 - 40 mm feed:: 1 - 999,999,9 mm speed of feed:: 60 m/min cuts max.:: 100 - 120 Schnitte/m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

screw ø:: für Extruder 90 mm screw length:: -- screw speedl:: -- U/min drive power:: 13,6 kW Condition: little used, as good as new Specification: gear pump ZP 75/50 for extruder size 90 - SEW helical gear units: R 97 - Siemens direct current motor: 1 GG5 118 - Drive power: 13.6 kW, 57 A - curved tooth coupling - With clamp for the head connection, - Clamping flange for extruder and head connection, - Base plate with linear guide rails, - Tooth shaft diameter: 75 mm - tooth width: 50 mm - helical gearing, hardened steel bearings, right-hand drive - without control The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Barwell Hydraulic Extruder – Used For sale: a used Barwell hydraulic extruder, designed for processing rubber compounds and elastomers. Barwell machines are well known worldwide for their robust construction, reliability, and consistent performance in industrial applications. The machine has been operated in an industrial environment, regularly maintained, and remains in good technical condition. Ready for further use after installation. Key features and advantages: Hydraulic drive ensuring smooth, stable, and precise extrusion Heavy-duty, solid construction for long service life Reliable operation, even with demanding rubber compounds User-friendly operation and easy integration into existing production lines Proven Barwell quality, widely trusted in the rubber industry Applications: Extrusion of rubber profiles and semi-finished products Preparation o ...

cross-section width:: 5 Schläuche 3-5 mm cross-section heigth:: 3 - 20 mm feed:: 1,5 - 50 mm Condition: used, very good condition only approx. 1 year in production Specification: circular knife cutting machine for slices and rings - small cutting machine with high-speed rotating circular knife - feed and knife movement, pneumatic - Tube or strand diameter min.: 3 mm - Tube or strand diameter min.: 20 mm - Feed (ring or strand length): 1.5 - 50 mm - Output depending on material max.: 60 strokes/min - Optionally, the following can be cut 5 tubes or strands: diameter 3 mm to 5 mm 4 tubes or strands: diameter 5 mm to 7 mm 3 hoses or strands: diameter 7 mm to 12 mm 2 hoses or strands: diameter 12 mm to 15 mm 1 hose or string: diameter 15 mm to 20 mm - Power requirement approx.: 0.37 kW - Air supply min.:  ...

cross-section width:: 100 mm cross-section heigth:: 40 mm feed:: 2 - 999.999,9 mm Condition: new, Specification: Impact knife cutting machine CC-600/40 for hoses and profiles - contact length: 600 mm - product diameter: 40 mm - belt width: 100 mm - Tractive force: 400 N to 800 N - Drive: 2 drives upper and lower belt - Conveyor belt speed: 100 m/min - Drive feed, cutting motor: Servo drives - Cutting capacity with blade max.: 4,000 1/min - Connected load: 3.5 kW - Dimensions L/H/B: 1,900 x 1,650 x 960 mm - Weight approx.: 580 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: 700 mm cross-section heigth:: 500 mm feed:: -- mm Condition: used, overhauled Specification: splitter for rubber bales - overhauled with CE - cross section width max.ca.: 700 mm - cross section height max. approx.: 500 mm - cutting force approx.: 10 tons - AC motor: 4 kW, 400 V, 50 Hz - Infeed roller conveyor for product transport - Machine stands on a raised pedestal - Two-hand safety control for driving the blade movement - Safety guard according to current standards - New control cabinet - New on-board system machine - Operating and maintenance manual in English - CE marking - Paintwork: according to customer requirements - Refurbished with 1 year warranty - CE marking, Option: - Output roller conveyor new The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

screw ø:: 90 mm screw length:: 20D screw speedl:: 0 - 60 U/min Condition: NEW, Specification: Rubber vacuum extruder - with warranty - Screw diameter: 90 mm - Screw length: L = 20 D (approx. 1,800 mm conveying length) - Screw speed: 0 - 60 rpm - Centre height of extruder: approx. 1,125 mm incl. base frame - Max. permissible injection pressure: 500 bar - with feed roller - Extruder water-tempered - Extruder base frame as welded construction, to accommodate the extruder with drive motor, the temperature control, the vacuum pump - Funnel piece with intermediate flange: two tempering zones approx. 4D = 480 mm - Vacuum cylinder: three tempering zones BL = 1,057 mm - End cylinder: one temperature control zone approx. 4D = 360 mm - Number of tempering zones: 5 - Heating capaci ...

Rubber mat, rubber plate, stop rubber, stop plate, rubber cover, rubber pad -Gum plate: from pre-tensioning technology -Thickness: 48 mm -Width: 150 mm -Length: 200 mm -Number: 12 pieces -Price: per piece -Weight: 4.3 kg/piece

Rubber sealing profile, sealing plate, curing tool, seal, edge protection, solid rubber rectangular profile -Rubber sealing profile: with 2 grooves, 3 pieces -Length: 3 x 8450 mm / total 25.35 m -Cross-section: 50 x 55 mm -Groove width: 5 mm -Weight: 120 kg

Rubber mat, rubber sheet, rubber stop, stop plate, rubber cover, rubber pad -Rubber cover: Rubber pad -Thickness: 30/6 mm -Length: 634 mm -Width: 100 mm -Height: 130 mm -Quantity: 18 pieces available -Price: per piece -Weight: 3.8 kg/piece

Transport rollers, wheels, casters, carrying rollers -Rubber-coated drive rollers, various designs -Roller diameter: 145 mm -Hole: Ø 20 mm -Roles: 11 -Price: complete -Design/Quantity: see photo -Total weight: 10.2 kg

Tires, solid rubber tires, tractor tires, forklift tires -Tire size: 18 x 7 - 8 -Rim: 4.33 R-8 -from forklift: Still type EFG 1.0/5002 -Number: 2 pieces -Price: complete -Dimensions: Ø 440/152 mm/piece -Weight: 25 kg/piece

Press (n°1) Upstroking Manufacturer: Agila Closing force: 850 Ton Year 1997 hydraulic Steam Platens : 3 2 cavities (250 mm opening) Size heating platens: 1100 x 1400 x 76 mm Diam. piston 650 mm Hydraulic pressure: max. 250 BAR Hydraulic tank: 500 L Complete manual included Size press 2400 x 1400 x 4200 mm (LWH) Weight +/- 23.000 kg

Rubber disc coupling, claw coupling, connecting coupling, torsionally flexible coupling -Manufacturer: ERL -Type: GR199 CF-D-160-10 -Flange: 315 mm -Bolt circle: 295 mm 8x holes -Outer diameter: 315 mm -Dimensions: 315/315/H54 mm -Weight: 6 kg

Rubber disc coupling, claw coupling, connecting coupling, torsionally flexible coupling -Manufacturer: ERL -Type: CF-D-160-10 -Shaft: Ø 22 mm (pre-drilled) -Flange: 315 mm -Bolt circle: 295 mm 8x holes -Outer diameter: 315 mm -Dimensions: 315/315/H70 mm -Weight: 9 kg

REP H48Y10W Horizontal Injection Moulding Machine Year of construction 2005 Machine Parameters Volume [cm3] 1000 Clamping force [kN] 1930 Injection pressure [bar] 1500 Moulds dimension [mm] 450x450 Tonnage 1.9t Platen size: 450x450 Cycles: 2,220,383 General condition: operational Dims [mm]: 4200 L x 1400 W x 2200 H Weight [kg]: 6750

Tires, solid rubber tires, forklift tires -Manufacturer: Continental, solid rubber tires CSE-Robust SC 15 from GSL aerial work platform -Tire size: 5.00-8/3.00 -Bolt circle: Ø 110 x 15 mm -Inner diameter: 67 mm -Quantity: 1 piece -Dimensions: Ø 460 x 125 mm -Weight: 20 kg

Rubber mat, rubber sheet, rubber stop, stop plate, rubber cover, rubber pad, rubber mat -Rubber cover: Rubber pad -Thickness: 9 mm -Length: 1000 mm -Width: 200 mm -Weight: 2.4 kg

rubber mat, rubber plate, stop rubber, stop plate, rubber cover, rubber pad, rubber mat -Rubber cover: rubber pad -Thickness: 9 mm -Length: 1985 mm -Width: 200 mm -Weight: 5.1 kg

tires, solid rubber tires, forklift tires -Manufacturer: Continental, solid rubber tires CSE-Robust Super Elastic SC 10 2 pieces -Tire size: 23 x 5 SC 10 RIM 3.75 P -Bolt circle: Ø 160 x 18 mm -Recess: Ø 110 mm -Price/Delivery: complete -Weight: 41 kg/piece

tires, solid rubber tires, forklift tires -Manufacturer: Vorwerk Rota, solid rubber tires 3 pieces -Tire size: 18x7-8 rim 4.33 R-8 532/272-1 -Bolt circle: Ø 148 x 18 mm -Recess: Ø 110 mm -Price/Delivery: complete -Weight: 22 kg/piece

tires, solid rubber tires, forklift tires -Manufacturer: Solideal, solid rubber tires 2 pieces -Tire size: 23x9-10 RIM 6.50F-10 -Bolt circle: Ø 162 x 20 mm -Recess: Ø 110 mm -Price/Delivery: complete -Dimensions: Ø 465 x 200 mm/piece -Weight: 40 kg/piece

tires, solid rubber tires, forklift tires -Manufacturer: Rigdon, solid rubber tire -Tire size: 23 x 9-10 -Rim: 6.50 F-10 -Bolt circle: Ø 162 x 20 mm -Recess: Ø 110 mm -Quantity: 1x tire available -Dimension: Ø 570 x 210 mm -Weight: 59 kg

tires, solid rubber tires, forklift tires -Manufacturer: Gumasol, solid rubber tires type GLE 2 pieces -Tire size: 8.25-15 -Rim: 6.0-15 -Bolt circle: Ø 225 x 32 mm -Recess: Ø 165 mm -Price/Delivery: complete -Dimensions: Ø 780 x 225 mm -Weight: 110 kg/piece

Tires, solid rubber tires, forklift tires, complete wheels -Manufacturer: Bergougnan, solid rubber tires 2 pieces -Tire size: 250-15 RIM 7.00F-15 -Bolt circle: Ø 225 x 28 mm -Recess: Ø 175 mm -Price/Delivery: complete -Dimensions each: Ø 700 x 215 mm -Weight: 90 kg/piece

rubber damper, engine damper, clutch, rubber coupling -Rubber coupling: rubber damper engine damper -Dimensions: see photos -Total dimensions: 240/210/H130 mm -Weight: 4.5 kg

Tires, solid rubber tires, forklift tires -Manufacturer: Kumaneko, solid rubber tires, 2 pieces with rim -Type: Widewall -Tire size: 27x10-12 -Bolt circle: Ø 220 x 27 mm -Recess: Ø 160 mm -Price/Sale: complete -Dimensions: Ø 600 x 255 mm/pc. -Total weight: 158 kg

tires, solid rubber tires, forklift tires -Manufacturer: Rigdon, solid rubber tire Solid with rim -Tire size: 18x7-8/4.32 (180/70-8) -Bolt circle: Ø 145 x 18 mm -Recess: Ø 110 mm -Quantity: 1x tire available -Dimensions: Ø 390 x 155 mm -Weight: 21 kg