rotary press used for sale

Rotary cultivator Pellenc Tournesol TS 1000 LD, three-point rear attachment, tool Rotary cultivator with 2 movable cutter blades on the boom (manual length adjustment approx. +/- 25 cm), hydraulic drive by means of 540 rpm push-on PTO pump, hydraulic lifting (1 x hydraulic connection ew required). Support and evasion function can be adjusted several times, solid sliding shoe (approx. 60 kg). Year of manufacture 2014, used. Manufacturer's specs: For tractors 50 hp, hydraulics 30-40 ltr. /min. at 180 bar, working speed max. 5 km/h, vine width min. 2.20 m.

Kiefel Roller Sheeter

For sale is an Aerzen GM 4 S rotary lobe blower. Can be purchased as a complete unit or separately as shown in the pictures. Year of Make: 2004 Condition: Blower overhauled - all wear parts renewed, immediately ready for use The blower has been professionally overhauled and is in perfect technical condition.

For sale is an Aerzen GMA 10.2 rotary lobe blower. Can also be used as a replacement for a GM 7 L. Year of Make: 2000 Condition: Refurbished - all wear parts renewed, immediately ready for use The blower has been professionally overhauled and is in perfect technical condition.

For sale is an Aerzen GMA 11.3 rotary lobe blower. Can also be used as a replacement for a GM 10 S. Year of Make: 1990 Condition: Refurbished - all wear parts renewed, immediately ready for use The blower has been professionally overhauled and is in perfect technical condition.

For sale is an Aerzen GMA 11.3 rotary lobe blower. Can also be used as a replacement for a GM 10 S. Year of Make: 1990 Condition: Refurbished - all wear parts renewed, immediately ready for use The blower has been professionally overhauled and is in perfect technical condition.

Stock number: SF018, Rotation filter, stainless steel,, Fratelli Gianazza type 15020., Double jacket., Rotation, for kieselguhr., Ø 500 mm, 5,6 m²., Material: Stainless steel AISI 304

For sale rotary dryer made from Bison, output 5 t/h, with heating stove 6mW with self feed and self cleaning moving fllor. With all need equipment, cyclon, chimney, and fans. Price 110.000,00 EUR EXW. +38765812388 Neven

TAYLOR Hydraulic Rotary Clamp - Working length mm. 2400 - Working width mm. 800 - 20 sections - N. 3 pressers for each section

Offer 25238 Specifications: - Max. load capacity with horizontal table top 350 Kg - Max. load capacity in all inclined positions 300 kg - Face plate diameter 400 mm - Through-hole / hollow shaft 125 mm - Face plate manually swivels left + right 0 - 90 ° - Rotary movement infinitely variable approx. 0.15 - 5.0 1/min - Right + Counterclockwise - E. footswitch - Welding current transmission approx. 350 A - Drive 400 V - Table height in horizontal position approx. 900 mm - Space requirement approx. W 1150 x H 900 x D 800 mm - Weight approx. 290 kg - Jaw chuck 250 mm

Heidolph Laborata 4001 complete with condenser and water bath, 0-270 rpm

Welding turntable - Welding rotary device with housingRound welding deviceLoad capacity approx. 50 kgTurning chuck diameter 300 mmTurning chuck speed 1.0-15 rpm. Mains connection 230 volts, 50 Hz- Spiral lathe chuck with inwardly stepped chuck jaws- Speed control infinitely variable via potentiometer- Drive via gear motor, direction of rotation left- Start via electric switch- Welding current transmission with sliding contact- Extraction connection 160 mm- Interior lightingDoor opening W x H 715 x 1060 mmInterior dimensions W x D x H

Vacuum pump, airframe pump, rotary vane pump ALCATEL type 100-132Fabr. No. 173082 - 3101 Year of manufacture: approx. 1995Volume flow: approx. 50 m3/hNegative pressure: 0.5 mbar (indicated on the nameplate)Negative pressure: - 0.9 bar (determined during test run)Engine power: 3 kWMotor speed: 1420 rpm. Mains connection: 400 volts, 50 Hz- Oil-lubricated rotary vane pumpDimensions L x W x H: 700 x 420 x 310 mmWeight: 78 kgGood condition; used

- Filter area 6 m2 - With residual filtration device - Machine in good condition

Rotary Brush Screen Properties: Total height 1900 mm Overall length 580 mm Depth 500 mm

Manufacturer:Porta Model: TRO-06-N08 Year of Manufacture: 2012 Machine Type: Production Cell with CNC Rotary Transfer Machine Control: Porta Additional Components: - Filter System (Knoll VRF450, 2011) - Chain Conveyor (Knoll) - External Cooling Unit - Mist Extraction System - Workpiece Conveyor - Handling: 3x 6-Axis Robots (ABB) - Cleaning System (Mako) with Filter System - Small Pallet Turner (Mako) Find more here - / Contact us at -

Stations: 24, substations: 20, side stations: 20, axes: 2/station, collets: 24, production output single/double cycle: 120/240 pieces/min, stroke: 35mm, max. workpiece diameter: 25mm, spindle speed: 20000rpm, machine weight: approx. 2650kg, control: Mikron MAC 50, operating hours: approx. 17335h. Documentation available. An on-site inspection is possible.

Rotary Brush Screen WESTFALIA BSB 200 Properties Type BOD 200 Machines No. 1 684 639 Total height 2500 mm Total length 600 mm Depth 600 mm Manufacturer: Westfalia Separator AG

Two identical rotary transfer machines Eubama including filtration systems are available. Workpiece diameter: 60mm, workpiece length: 320mm, clamping stations: 10, cycle rate: 20/min, spindle stroke: 100mm, drilling capacity steel/brass: 20mm/30mm, threading capacity steel/brass: M30/M40. Documentation available. An on-site inspection is possible.

table diameter: 400 mm table load: . t table height: . mm total power requirement: . kW weight of the machine ca.: . t dimensions of the machine ca.: . m The technical data is provided by the manufacturer or operator and is therefore not binding for us. We reserve the right to prior sale, our terms and conditions of business and sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, crane capacity 70 t More than 10,000 items of accessories for your workshop If you want to sell machines, production lines, or your business, then get in touch with us. You can find more offers on our website. Viewings are possible by arrangement. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 400 mm table load: . t table height: . mm total power requirement: . kW weight of the machine ca.: . t dimensions of the machine ca.: . m Small defect on the faceplate, see pictures. The technical data is provided by the manufacturer or operator and is therefore not binding for us. We reserve the right to prior sale, our terms and conditions of business and sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, crane capacity 70 t More than 10,000 items of accessories for your workshop If you want to sell machines, production lines, or your business, then get in touch with us. You can find more offers on our website. Viewings are possible by arrangement. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 400 mm table load: . t table height: . mm total power requirement: . kW weight of the machine ca.: . t dimensions of the machine ca.: . m The technical data is provided by the manufacturer or operator and is therefore not binding for us. We reserve the right to prior sale, our terms and conditions of business and sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, crane capacity 70 t More than 10,000 items of accessories for your workshop If you want to sell machines, production lines, or your business, then get in touch with us. You can find more offers on our website. Viewings are possible by arrangement. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table diameter: 400 mm table load: . t table height: . mm total power requirement: . kW weight of the machine ca.: . t dimensions of the machine ca.: . m The technical data is provided by the manufacturer or operator and is therefore not binding for us. We reserve the right to prior sale, our terms and conditions of business and sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, crane capacity 70 t More than 10,000 items of accessories for your workshop If you want to sell machines, production lines, or your business, then get in touch with us. You can find more offers on our website. Viewings are possible by arrangement. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Rotary valve 1.1 kW, as good as new

Our KVK 5 is a semi-automatic rotary arm wrapper that, compared to our turntable wrappers, has the advantage that your pallets can be placed at ground level for the wrapping process. It is equally ideal for light and unstable as well as heavy packaged goods, as there are no centrifugal forces and no load-bearing capacity has to be observed. In addition, the KVK 5 model is equipped with a pre-stretch system for 250% elongation. With this pre-stretching system, you can produce up to 3.5 m of film on the pallet from 1 m of film on the roll and reduce your material consumption enormously. With the KVK 5, there is only a minimum application tension, so that even light packaged goods are not pulled off the pallet. Only the application and separation of the film has to be done manually with this wrapper. The machine weight of almost 1000 kg shows how solid and stable this winder is. ...

Key data: 250 , 7

Rotary screw air compressor. Pressure: 7.5 bar. Power: 136 kW. Rotation speed: 1488 r/min. With new screen.

Description: Rotary Lobe Pump Flow rate: 2.0 m³/h Operating pressure test 0.8 bar Motor: 1.1 kW - With connections: suction side DN 40 and pressure side: DN 40 - With chassis mobile, 2 swivels and 2 fixed castors - With cable and CE plug 16A Dimensions: Length: 1100 mm Width: 620 mm Height: 1100 mm Note: Pump 100% tested, with function guarantee On request, infinitely variable with frequency converter for an additional cost. Connections can be changed at an additional cost.

Tilting Rotary Table Shelf diameter: Ø 300 mm Manual tilt vertically + horizontally Maxi vertically tilt: 90° Base/shelf height horizontal position: 250 mm Height in vertical 90° position: 400 mm Seating Surface: Length 450 mm x Depth 500 mm x Height 250 mm Weight: approx 200 kg

GENERAL Project No.: 905789 Quantity: 1 pcs. Manufacturer: BUDERUS Type: BDG 220 Control: Siemens 840 D solutionline Year of Make: 2020 Condition: Used machine Spindle Approx (hrs): 3000 Shifts machine one approx. (hour): rarely used DESCRIPTION GRINDING Max. workpiece diameter 440 mm Max. workpiece height 150 mm Travel in X 170 mm Max. rapid traverse speed in X/Z 30 m/min Max. feed speed in X 0.01-15 mm/min Max. speed workpiece spindle 1000 1/min OTHER EQUIPMENT Workpiece probes for measuring thickness deviation Gate sensor Splash protection cladding with fully encapsulated working area Automatic work room door Lighting in the work area Mechanical oil/emulsion mist extraction system Coolant device with paper belt filter High pressure pump 25 bar Mobile control unit for set-up operation with electronic handwheel Machine condition light Au ...

Offer 25347 Hydr. Manipulator - Positioning - Welding Rotary and Tilting Table Specifications: - Max. load capacity incl. work table 4000 kg - Face plate hydraulically swivel 0 - 180 ° - hydr. Height adjustment of the face plate - Face plate with holes D 28 + threaded holes Ø 1600 mm - Table moves in the last inclination or horizontally approached - Rotary movement electrically hydraulic with right + counterclockwise rotation - min. / max. rotation speed 0.1 - 1.4 rpm - min./ max. table height in horizontal position - approx. 1040 / 2140 mm - Welding current transmission approx. 600 A - Drive 400 V - Handheld remote control + E. foot switch - Space requirement approx. W 2000 x H 1100 x D 3200 mm - Weight approx. 5700 kg

Offer 25352 Hydr. Manipulator - Positioning - Welding Rotary and Tilting Table Specifications: - Max. load capacity incl. work table 2000 kg - Effective payload 1700 kg - Face plate hydraulically swivel 0 - 180 ° - hydr. Height adjustment of the face plate - Table moves in the last inclination or horizontally approached - Rotary movement electrically hydraulic with right + counterclockwise rotation - min. / max. rotation speed 0.75 - 2.0 rpm - 3 D work table DEMMLER 800 x 800 mm - min./ max. table height in horizontal position - approx. 600 / 1550 mm - Welding current transmission approx. 600 A - Drive 400 V - Handheld remote control + E. foot switch - Space requirement approx. W 2100 x H 600 x D 1500 mm - Weight approx. 1200 kg

Offer 25357 Hydr. Manipulator - Positioning - Welding Rotary and Tilting Table Specifications: - Max. load capacity incl. work table 4000 kg - Face plate hydraulically swivel 0 - 180 ° - hydr. Height adjustment of the face plate - Face plate with holes D 28 + threaded holes Ø 1600 mm - Table moves in the last inclination or horizontally approached - Rotary movement electrically hydraulic with right + counterclockwise rotation - min. / max. rotation speed 0.1 - 1.4 rpm - min./ max. table height in horizontal position - approx. 1040 / 2140 mm - Welding current transmission approx. 600 A - Drive 400 V - Handheld remote control + E. foot switch - Space requirement approx. W 2000 x H 1100 x D 3200 mm - Weight approx. 5000 kg

Key data: 18

Machine name: Rotary Transfer Machine Pfiffner HB45 - 18 Hour Manufacturer: Pfiffner Machine number: HB45 Year of construction: 2006 Condition: used Functionality: Fully functional

Properties: Length 780 mm Total height 2400 mm Motor power 0.25 kW Depth 780 mm Volume 931 L Steel as a material Description: Front flange - DN 50 reduction Flange rear - reduction DN 50 bottom: Disc valve DN 100 Motor: 0.25 KW

1 POLYTEX "Waterfall Sample" Mounting Machine type FC, year 2017, semi-automatic "Waterfall" sample mounting machine of modern design for "Waterfall" sample strips. Electronic power traction feed with programmable logic controller (PLC).

1 POLYTEX pinking machine type ZH (Zigzag cutting) knife width 500 mm, serrated knife with 5 mm serration gauge, stroke 50 mm,

1 TUPESA rotary garment dyeing and washing machine type STONE 550, capacity up to 550 Kg (constructor indication and depending on articles) drum diameter 1950 mm x depth 1700 mm (volume 5000 L)

1 POLYTEX "Waterfall Sample" Mounting Machine type FB, year 2017, semi-automatic "Waterfall" sample mounting machine of modern design for "Waterfall" sample strips. Electronic power traction feed with programmable logic controller (PLC) and touch screen. sample size width infinitely variable up to 800 mm, unlimited length, output single ply up to 900 stripes per hour, output two-ply up to 450 stripes per hour,

1 HOZA pinking machine type ZM 50 (Zigzag cutting), cutting width 500 mm, serrated knife with 4 mm serration gauge, manual actuation

1 POLYTEX pinking machine type ZP-V (Zigzag cutting), knife width 1020 mm, machine equipped with FASNACHT security light guards, stroke up to 65 mm height, up to 50 cuts per minute, PLC and inverter controlled. Fully automatic electric double feed system with 2 programs for simultaneous prechoice of sample length and width. Ensures highest degree of accuracy and operating comfort. Machine delivered with all possible extras/options namely: cutting height adjustment 0-1-2 mm (with or without carton underlay), increased hold-down force with hydraulic speed regulators, reinforced laser pointer.

1 SUCHY fabric winding and cutting machine, year of manufacture 2015, roller surface width 220 cm, Unwinder with pneumatic expanding shaft for cardboard cores, Inspection station, Cross-cut knife holder (for manual cross-cutting), Rewinder with pneumatic expanding shaft for cardboard cores, Speed: 0–50 m/min

1 TUPESA sample rotary garment dyeing and washing machine type TSP-2-CP, high temperature high pressure machine, year 2001, capacity 2 Kg, drum diameter 470 mm, drum depth 250 mm, drum volume 42 L, dye cycle controller TUPESA type RS-1, drum rotation 0-28 rpm, machine equipped with centrifugation process of 450 rpm, 2 addition vats. Machine designed to work with temperatures up to 140 ºC. This type of machinery is suitable for dyeing all types of garments such as polyester, polyamides, synthetic blends, etc.

1 TUPESA rotary garment dyeing and washing machine type TSP-25-CP, high temperature high pressure machine, year 2008, capacity 25 Kg, drum diameter 1100 mm, drum depth 610 mm, drum volume 580 L, dye cycle controller TUPESA type RS-BASIC PLUS touch screen, drum rotation 0-28 rpm, machine equipped with centrifugation process of 700 rpm, 5 addition vats. Machine designed to work with temperatures up to 140 ºC. This type of machinery is suitable for dyeing all types of garments such as polyester, polyamides, synthetic blends, etc.

1 TUPESA rotary garment dyeing and washing machine type TSP-55-CP, high temperature high pressure machine, year 2004, capacity 55 Kg, drum diameter 1250 mm, drum depth 1100 mm, drum volume 900 L, dye cycle controller TUPESA type RS-1, drum rotation 0-28 rpm, machine equipped with centrifugation process of 650 rpm, 5 addition vats. Machine designed to work with temperatures up to 140 ºC. This type of machinery is suitable for dyeing all types of garments such as polyester, polyamides, synthetic blends, etc.

1 KAPPA pinking machine type 51N (Zigzag cutting), knife width 500 mm, power driven swatch and sample cutting machine, serrated knife with 4 mm serration gauge, year 2022, precise and accurate thanks to mechanical movement of the cutting board (turn wheel), exchange of knife is effortless and fast, motor 1,5 kW (2 HP)

1 HOZA (Germany) pinking machine type EZM 60 (Zigzag cutting), knife width 600 mm, electrically actuated, year 2019, laser for cutting line indication, machine controlled per PLC, knife with 4 mm serration gauge, up to 30 cuts per minute, 3 x 380 V, 50 Hz,