roland 200 used for sale

Key data: 160 KW, 200 kVA, 400 V

Generator Set Specifications: Model: EQ-I200160 Primary power: 200 kVA / 160 kW Standby power: 220 kVA / 176 kW Voltage: 400/230V Frequency: 50 Hz Speed: 1500 rpm (revolutions per minute) Engine Specifications: Engine brand: Iveco Engine Model: NEF67TM7 Bore x Stroke (mm): 104 x 132 Displacement (L): 6.7 Compression ratio: 17.5:1 Induction: Turbocharged & Intercooler (or Aftercooler) Fuel System: Inline (Series) Regulator Type: Mechanical Dimensions of the generator set (closed): Length: 3150 mm Width: 1056 mm Height: 1900 mm Weight Open: 2000 kg (Note: Here it says "Weight Open" despite the heading "Dimensions of the generator set (Closed)". I left it as it is in the original.) Standard features: 4-stroke, 1500 rpm, water-cooled high-performance diesel engine Stamford alternator ABB Circuit Breakers Manual operation protection system Flexible oil  ...

Key data: 1140 °C

Continious Brazing/Sintering furnace manufactured by Mahler. Type: Humpback (lower H2 consumption). Belt width: 450mm Clearance above belt: 200 mm Heating length: 5000mm Gross throughput: 600 kg/h Electric heating power: 198 kW Service temperature: 1140 Adjustable range of belt speed: 100-1000 mm/min Temperature cotroul groups: 5x Total length: 30m width: 1,8m height: 2,8m Hydrogen connection: 0,1bar 30Nm3/h (type 3.0) Nitrogen connection: 0,1 bar 60 Nm3/h (type 5.0) Exhaust gas : 300 m3/h Furnace is in use, and was regularly serviced. In 12. 2024 brick lining, heating elements, thermocouples, mesh belt and muffle was replaced . Spare parts are available, in case of interest, can be subject of seperate agreement. Offer includes: - Water cooling system with glicol base heat exchanger - Exhaust tubes (2x around 5m Stainless steel) - 5x sensor system to detect ex ...

Swash-up machine Material : Stainless steel --> 3-deck machine, screening in 4 fractions.

Processing plant Manufacturer: Koruma Type: Disho A140/200 No.: 4,209 Built: 1988 with user manual no vacuum, no double jacket with control cabinet LWH: 1400 x 850 x 1450 mm

Bin lifter Type Lifting equipment Height 1900 Width 1500 mm Length 1800 mm Main material Stainlees Steel Time of realisation 2-3 weeks

Part Number: 7687 SPECIFICATIONS - inlet width 540mm - inlet height 300mm - shaft width 630mm - shaft diameter 700mm - knife length 630mm - number of knives 2pcs - sieve dimensions 40x40mm - toothed pulling shaft at the bottom - lower shaft motor 4kW - toothed pulling shaft from above - upper shaft motor 4kW - belt feeder - length of the feeding belt 4720mm - width of the feeding belt 500mm - main motor 75kW - Autoewers (adjustable) - total dimensions of the machine length/width/height 3100x2000x1830mm - total dimensions of the feeder length/width/height 4800x780x980mm - weight about 5000kg ADVANTAGES – made in Germany – autorewers – used chipper, very good condition Net price: 120900 PLN Net price: 28447 EUR depending on the price of 4.25 EUR (Prices may change with higher fluctuations)

Mechanic plate bending machine Goyar 3C-25/20. Bending lenght: 2000mm. Bending capacity: 25mm. Diameter of upper cylinder: 285mm. Diameter of lower cylinders: 235mm. Main motor power: 20cv. Bending speed: 5 mpm. Weight: 5500Kgs.

Hobart A 200 Planetary Stirrer 3 speed full gearbox 1st gear 107 rpm 2nd gear 198 rpm 3rd gear 361 rpm Boiler capacity 20 l Very good operational condition, directly from production!

Wintersteiger DSG 150/200 Thin-cutting creel with center cut device and planing device Cutting width: 150 mm | Cutting height: 200 mm For sale is a professional thin-cutting creel of the type Wintersteiger DSG 150/200, equipped with a center cutting device and integrated planing unit. The machine is ideal for precise slat production with minimal material loss – especially in the parquet, furniture and solid wood processing sectors. Specifications: • Cutting width: up to 150 mm • Cutting height: up to 200 mm • Minimum fin thickness: approx. 1.5 mm • Kerf: from approx. 0.9–1.2 mm (depending on the tool) • Stroke rate: up to 450 strokes/min • Feed speed: approx. 0.3 – 1.8 m/min • Main motor power: 11 kW • Cutting accuracy: ± 0.1 mm Equipment: • Center incision device for centric incisions • Integrated planing device (double planer)  ...

Fixed bed milling machine Zayer 2000BF. Table: 2500x700mm. Longitudinal travel: 2000mm. Cross travel: 1000mm. Vertical travel: 1000mm. ISO50. Speeds: 18. (28-1800rpm). Power: 15cv. Weight: 13000Kgs. Equipped with DRO Fagor.

Artech HD granulator SG 80 120 with 200 kW. Well suited for EBS, cables, used tires, plastics, AzV. Well maintained machine. Recently overhauled.

CNC controller: Mitsubishi M-720BM (MAPPS 2) Capacity X-axis travel mm: 260 Z-axis travel mm: 520 C-axis: 360º (0.001°) Turning length mm: 515 Max. turning diameter mm: ø: Ø356 Upper turret Tool holder: 12 Main spindle Speed spindle rpm: 5000 Drive power spindle kW: 15/11 Spindle bore mm: 73 Manufacturer: KITAGAWA Counter spindle Counter spindle travel mm: 525 Equipment Chip conveyor Signal lamp Tool measuring arm Workarea light Working time hours Under power: 7.456 Cutting Time: 5.423 Basic machine dimensions / weight Length mm: 3.495 Width mm: 2.050 Height mm: 2.230 Weight kg: 5.800

TETRA PAK A3 COMPACT FLEX 250ML AND 200ML PRISMA FILLING LINE Item #: Usm-131 Category Tetra Pak A3 CF/Flex A3 Compact Flex 200ml and 250ml Prisma Filling Line with quick Change kit. Year of manufacturing for the full line is 2016 and few working hours, just like new 1-A3 Compact Flex 200ml and 250ml Prisma Filling machine, Speed 9000 Packs per hour 2-Date Printer 3-Helix Accumulator 30 meter 4-Straw applicator TSA 30 5-Shrink 30 6-Conveyors and Paper Trolly

0: , St. Width: 1080 mm Length: 2000 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Introducing the Danstoker A-S Boiler – Reliable, Efficient, and Built to Last! Specifications: Model: EEB-W HT Serial Number: 78-6155 Year of Manufacture: 2009 Max. Heat Output: 1005 kW Max. Steam Rating: 6.0 Bar (Design Pressure) Design Temperature: 110°C Test Pressure: 9.0 Bar Water Volume Capacity: 3143 Liters This high-performance boiler is engineered for durability and efficiency, making it ideal for industrial applications. With its robust construction and certified design, the Danstoker A-S ensures reliable operation under demanding conditions. Perfect for businesses seeking a trusted heating solution! for more Details: 07379844145 financeukpowergeneratorsltd.com hashtag#Danstoker hashtag#IndustrialBoiler hashtag#Efficiency hashtag#Reliability hashtag#HeatingSolutions hashtag#EngineeringExcellence Private Notes

Optical sorting machine with material feed (via 2 stainless steel infeed hoppers and 2 electronically controlled vibratory chutes), material chute (made of specially coated aluminium), optical unit (4 high-resolution monochrome cameras with 2,048 pixels each; integrated image processing with a resolution of 0.09 mm) and blow-out system (144 high-speed blow-out nozzles with 1,400 cycles per second). The machine can be used, for example, to remove particles of different colours or foreign bodies from a material stream. Throughput: 500 to 800 kg/h (for quartz sand 0.1 - 6.0 mm). IP6X protection class for dustproof operation; incl. connection for external dust removal. Dimensions: 1.4 m wide x 1.8 m deep x 1.90 m high.

Inv. Num. : 5457 Type: UB 63/2000 Producer: HOL-MONTA Created: 2001 Parameters: Control system: Kavalír Maximum grinding length: 2000 mm Grinding diameter: 630 mm Tip stroke: 375 mm Total power requirement: 41 kW

Code 61063 Description Surface grinding machine Make ABA Model FFU 2000/60 Serial No. 208 125 Control Abamatic 3 Year 1986 Tablesize 2510 x 500 mm Grinding surface L x B x H 2000 x 600 x 700 mm Magnetical plate size L x B 2000 x 500 mm Speed table movement 3 – 30 m/min. Max. distance table – centre grinding wheel 900 mm Grinding stone dim. Stone x Wide x Taper Ø 400 x 50 x Ø 127 mm Spindel power 26 kW Spindel speed 1600 - 3000 rpm Motor power 26 kW – 380 Volt Total electr.com. 34 kW Total space L x W x H 7000 x 3500 x 2650 mm Weight 10500 kgs Accessoiries Elec. Magneticplate 2000 x 500 mm Coolant with paperfilter Digital readout Grinding stones, etc. Condition Machine is in good condition

Banding system ATS US 2000 AB Cornerline; good condition; serviced and tested by ATS customer service; bandwidth 30mm; frame size 360x160mm; Min. Product width 80mm, max.165mm; Max. Product length 270mm; Max. Produnkt height 110mm; Compressed air required. Ultra sonic banding machine ATS US 2000 AB Cornerline; good condition; cleaned and checked by the support of ATS Germany; band width 30mm; frame size 360x160mm; min. product width 80mm, max.165mm; max.product lenght 270mm; product hight 110mm; pressure air needed.

Robots from Fanuc, installed since 2022

specifications: - Clamping area approx. 400 x 300 mm - Travel across x approx. 500mm - Travel along Y approx. 300mm - 2 Handwheels - Height 220 mm - 4 T - grooves 14 mm - Distance of the T - grooves approx. 72mm - Space required approx. W 1100 x D 900 x H 220 mm - Weight approx. 190 kg

Spindle diameter 2,000 mm Turnerable diameter 2,000 mm MACHINE IN MECHANICAL/ELECTRIC RETROFIT PHASE

Bosch Turbo Scara SR6 Swivel Arm Robot The SR6/SR8 robot system consists of robust robot mechanics with four freely programmable axes. Thanks to its high speed and load capacity (up to 8 kg), the robot is predestined for assembly work and fast pick & place movements. The turboscara SR6 and SR8 are swivel-arm robots (Scara robots) with four axes and the following advantages: • Minimal cycle time with maximum precision • Large working area and different lifting distances • Defined mechanical interfaces • PC control with a wide range of communication options • Complies with international standards • Brushless drive technology reduces repairs • Integrated user installation, optional: gripper for connecting a tool connector • Integration of safety technology (safety class 3) as standard • User power supply (24 V) in the control cabinet • The BAPS program ...

hydraulic tipping tank or tipping bucket Price: 800,-p.pcs. + VAT reclaimable: R928 hydraulic tipping trailer, tipping wagon MAFI hydraulically tiltable by means of a manual hydraulic pump. Load capacity 2000 kg Overall height 2000mm Inner body dimension Br.1900mm Flat 900mm top 1450mm 2 pieces are to be handed in Because they have been stored for years, they are partly rusty or the paint is peeling off. Otherwise very good technical. Condition in my opinion see also photo of the cylinders easily convertible as a tipping container on a forklift (has been done before) unscrew the chassis weld on 2square tubes for fork mounting Unscrew the manual hydraulic pump with quick couplings and adapt it to forklift hydraulics It is best to visit and try it out for yourself. I had several at one of them the chassis was removed and the holder for forklifts was welded on, intended for wo ...

Very high-quality CNC – controlled precision sheet metal round bending machine with automatic bending sequence calculation – automatic CNC – controlled double-sided pre-bending – conical bending device, three hydraulically driven rollers (one hydraulic motor per roll), hydraulic linear sub-roll adjustment – hard chrome-plated piston rods – hardened and ground rollers - PILZ® laser protection - BECKHOFF® CNC – control with Ethernet technology and large touch screen - DANFOSS® precision hydraulics – central lubrication system Maximum bending length 2,000 mm Roll diameter 170 mm Smallest weft diameter = 1.1 x the roll diameter The rollers run in bronze plain bearings. Nominal pre-bending performance over the entire bending length at 5 x D = 5 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 7 mm sheet steel/ST40 Drive  ...

Frequency Brand: Heinrich Baumüller Type: BKF/12/100/400-2002 Power Converter Not checked for functionality. Sold only to traders!

We sell a pietroberto fork kneader. The machine is ideal for flatbread doughs. Used and overhauled / Warranty

max. wheel diameter: 3000 mm gear width: 1200 mm max. module: 30/40 min. module: 2 table diameter: 2500 mm table load capacity: 400 kN hob dia. - max.: 450 x 500 mm milling spindle speeds: 10 - 165 U/min hob length max.: 500 mm tip circle diameter: 2050 mm tooth helical angle min/max: 0 - 45 ° center distance betw. workpiece-tool min/max.: 150 - 1750 mm milling slide swivelling: 50 Grad distance table / counter stay: 1050 - 2050 mm shifting: 300 mm workpiece weight: 40 t table bore diameter: 800 mm depth of hole: 1100 mm main drive motor: 37 kW min. workpiece diameter: 290 mm min. number of teeth: Wälzfräsen 20 min. number of teeth: Formfräsen 2 taper: MK 100 feeds axial: 1 - 1800 mm/min radial feed: 1 - 500 mm/min feed: Tangential 1 - 450 mm/min rapid traverse: 1875 / 530 / 470 mm/min electrics - voltage/frequency: 380 / 50 V/Hz control: Siemens Sinumerik 3M total power requirement: ...

turning diameter over bed: 460 mm turning diameter over slide rest: 274 mm turning length: 2000 mm spindle bore: 58 mm spindle turning speed range: 25 - 2000 U/min turning dia. in gap: 690 mm metric threading: 41 / 0,1 - 14 mm thread - inch: 60 / 2 - 112 inch. thread - module: 34 / 0,1 - 7 mm Whitworth-thread: 60 / 2 - 112 TPI adjustment of the upper slide: 140 mm dia. of quill: 60 mm quill stroke: 120 mm total power requirement: 5,5 kW weight of the machine ca.: 1,7 / 2,0 t dimensions of the machine ca.: 2,2 x 1,0 x 1,3 m A comprehensive range of quality centre lathes characterised by wide versatility,high accuracy and extremely rigid construction. The machines are well equipped with a multi-fix quick change tool post and 2-axis Newall digital readout fitted as standard and a variable speed option is available. Huvema lathes fully conform to CE regulations. Also available in: 1,5m 3 ja ...

Tensile testing strength: 420 kg pulling force - max.: 2360 Kg weight: 380 kg battery: 24 V / 240 Ah battery: Gewicht: 320 Kg weight of the machine ca.: 700 Kg Dimensions (HxWxD): 1,2 x 1,2 x 1,4 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 200 mm, 300 , 200

Profile bending roll used equipment hydraulic model AR200 year 2008 make MG Italy Capacity bending chart photo in enclosed -Technical data: Output shafts size 200 mm -Machine complete with set of rollers adjustable for the various shape of profiles. -Traction tool hydraulic operated for the HEB-beam - IPE - UNP bending the hard side. -Lateral correctors left and right side hydraulic operated in 3 direction. -Included additional set of rolls for pipe 6" inches -Machine with 3 rolls driven system with individual hydraulic motor and axial gear-unit on each shaft. -The 3 shafts working on bearings, heavy duty type with sealed lubrication. -Centralized control panel movable on wheels with all electric commands. -Dual rolling speed up to 5 mtr/min with automatic balancing system between the 3 rolls. -Safety devices in compliance with European regulation. CE mark. - ...

Ref.nr. 00887 Description of the system Used swap bodies vehicle Swopper 3 ACHSER Manufacturer: Fiege tec Model Swopper max 200 (3 axles) Year of manufacture 2014 (possibly also 2010) still to be clarified Self propelling chair Swopper max 200 with global viewing cab and the single-lever Masterpilot for all driving, lifting, steering and locking functions ergonomically mounted on the right side of the driver's seat. A powerful diesel engine serves as the drive. The hydrostatic drive allows the speed to be infinitely adjusted both forwards and backwards. The max. 200 is equipped with an articulated drive axle at the front and an air-sprung two-axle unit at the rear. Front tyres: two pieces 12.00-20 Industrial – Rear tyres: eight pieces 7.50-15 Industrial. Lighting according to STVZO consisting of 2 three-chamber lights, side spotlights and position lights, reversing lig ...

sheet width: 3100 mm plate thickness: 6 mm pre-bending: 5 mm upper roll diameter: 200 mm min. bending diameter: Ø 300 mm bending speed: 5 m/min total power requirement: 5,5 kW weight of the machine ca.: 4.000 kg dimensions of the machine ca.: 4800x1300x1270 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 200 kN stroke length max.: 200 mm working feed: 10 mm/sec return speed: 20 mm/sec : 480x1060 mm work height max.: 900 mm toolpiece height max.: 200 mm total power requirement: 2,2 kW : 200x12 mm bending capacity max. - round: 48x4,0 mm weight: 500 kg Overall size: 1010x480x1120 mm Domestic equipments: - with semi-automatic control (99 programs with 16 steps each) - including bending bolt (without punch) - Tool holder for dies - Foot pedal Equipment: - Stamp, small U = 145 mm 85 °, H = 200 mm, R = 5 mm - Quick change monometer 85 °, H = 200 mm, V = 63 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Environmental technology Kreisel Krauschwitz - Rotary valve Product name: Rotary valve Manufacturer: Umwelttechnik Kreisel Krauschwitz Type: ANG 200-11-12 Z (RF47) Year of construction: 2006 Machine number: 61614 Condition: used Inlet opening: 200 x 200 mm Outlet opening: 200 x 200 mm Cell depth: 60 mm Cell width: 200 mm Cell wall: 8 mm Number of cells: 8 Engine: SEW-EURODRIVE Type: RF47 DT71D4/TF RPM: 1380/12 Power: 0.37 kW Voltage: 230/400 V Protection class: IP55 Machine size: 850mm x 300mm x 300mm (L x W x H) Transport dimensions: 1,200mm x 800mm x 450mm (L x W x H) on pallet Number of packaging units: 1 Weight: approx. 100 kg on disposable pallet The rotary valve was completely refurbished, checked and tested for function in our company. Price: 1.390,00 € (VB) plus VAT from location Grunow (Brandenburg) (Subject to changes and errors regar ...

Ref.nr 00888 Designation of the system Swap bodies Vehicle Swopper 2-axle Manufacturer: Fiege Tec Model Swopper max 200 (2 axles) Year of manufacture 2004 Self-propelled Swopper max. 200 with global viewing cab and the single-lever Masterpilot for all driving, lifting, steering and locking functions ergonomically mounted on the right side of the driver's seat. A powerful diesel engine serves as the drive. The hydrostatic drive allows the speed to be infinitely adjusted forwards and backwards. The max. 200 is equipped with an articulated drive axle at the front and an air-driven single-axle unit at the rear. Front tyres: two pieces 12.00-20 Industrial a 50% - Rear tyres: four pieces 2.50-15 Industiral approx. 50% lighting according to StVZO consisting of 2x three-chamber lights, side spotlights and position lights, reversing lights, rotating beacon Technical details Hour ...

pressure: 200 t chamfer lenght: 3000 mm distance between columns: 2560 mm dayligth: 450 mm throat: 450 mm adjustment of stroke: 240 mm horn length over column outer edge each: 175 mm table length: 3050 mm table width: 280 mm table height over floor: 820 mm electrics - voltage/frequency: 220/50 V/Hz control: CYBELEC, DNC60 stroke: 250 mm operating pressure: 150 bar total power requirement: kW weight of the machine ca.: 15 t dimensions of the machine ca.: L:4,0 x B:3,2 x H:3,44 m • hydraulical press brake, • new control CYBELEC DNC60 (in 2005), • lower part of the machine moves down 500 mm to the floor, at the moment the machine is mounted on a double-T-support, • prism and upper part of the machine in 3000 mm length The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 290 mm turning length: 850 mm swing diameter: 600 mm control: Siemens type: 840 D mm spindle passage: 103 mm turning speeds: 3000 U/min live tooling: 3000 U/min rapid travel - grinding spindle: 25 m/min total power requirement: 65 kW weight of the machine ca.: 11 t dimensions of the machine ca.: m Offer price without tools Optionally, the accessories can also be purchased: 106 steel holders for indoor and outdoor use. External machining, 20 driven tools (including 10 x angle tools) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

thickness of jaw: 200 mm clamping range: 210 mm clamping height: 55 mm weight: 34,5 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 2000 mm table width: 1000 mm table height: 850 - 900 mm weight of the machine ca.: 0,45 t Welding table / perforated table: Hole diameter: 28mm The table is made of 15mm thick, high-alloy steel S355 JR T = 15 The surface is untreated. Sidewalls 165mm height adjustable from approx. 880 - 980mm Ribbed underside for reinforcement. including floor storage Accessories optional Surface flatness 0.2 - 0.4mm on 1000mm. Very sturdy base, so the Table can be moved with a pallet truck. The accessories shown are optional! Pallet truck is not included in the scope of delivery The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

width of the strips: 100 mm band length: 915 mm dimensions of grinding wheel: 200 mm work table:: 170x125 / 265x150 mm total power requirement: 0,5 kW weight of the machine ca.: 26 Kg dimensions of the machine ca.: 0,6 x 0,5 x 0,3 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 2000 mm Working width: 360 mm Wheel width: 360 mm roll diameter: 60 mm : 800 kg height adjustment: 650 - 950 mm weight of the machine ca.: 0,045 t dimensions: 2,07 x 0,48 x 0,21 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Number of sanding units: 2 St. sanding width: 190 mm Sanding height max.: 2-180 mm LÖWER-Doppelseitige Schleifmaschine DSM 2000 Doppelseitige Einzelholzschleifmaschine zum Schleifen von Massivholz wie z.B. Fensterhölzern etc. Stabile Top-Aus- führung mit langen Gußtischen, Bürst- und Finisheinrichtung und Transportbandvorschub. Geeignet für hohe Dauerbelastung auch bei höheren Spanabnahmen. - versetzt angeordnete Schleif- und Finishaggregate oben und unten - direkt angetriebene gummierte Schleifrollen für schlupffreie Kraftübertragung - Kombischliff über Rolle und Schuh für hohe Spanabnahmen bei gleichzeitig ebener Eingriffszone - wartungs- und verschleißfreie CERMET-beschichtete Schleifschuhe mit sehr guter Wärmeleitfähigkeit und absoluter Maßhaltigkeit - Fremdkühlung der Schleifzonen für einen kühleren Schliff und höhere Schleifbandstandzeiten - zwangsgeführte pneu ...

Reference ID PP-52915 Category 5-Colors Flexo Printer Manufacturer Bobst Model Flexo 200 Year Built 1988 Color 5 Impression- Working Hours - Speed-- Max. Size - Min. Size - Condition Good Location Europe Availability Immediately Machine Description 5 colors Feeder type: Vacuum sheet feeder with pneumatic pressure plate Anilox rollers: All used, ceramic Printing units 1–4: 160 lines/cm, maximum feed volume 8.5 cm³/m² Printing unit 5: 100 lines/cm, maximum feed volume 10.5 cm³/m² Doctor blade system: Ceramic anilox rollers with metal doctor blade Vacuum sheet transport: Yes, 2007 vacuum transport (modified stainless steel suction plate) System upgrades: Sheet cleaning and warm air dryer, both Type 2 200 from DUO TECHNIQUE;

width of the strips: 150 mm band length: 2000 mm band speed: 33 m/sec total power requirement: 4 kW weight of the machine ca.: 100 t dimensions of the machine ca.: 1,2 x 0,5 x 0,85 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.