rock used for sale

Rock.Zone RR 300 asphalt milling machine, cutting head width 300mm, drive power 30KW, dead weight 450 kg, operating pressure 210 bar, total length 860mm, the machine has been used only lightly, very good condition

Rock Wool factory 16.000 t/y - Stone wool - Laine de roche - nearly new - for all products.2,5 tons Rock Wool per hour - Coppola Kiln, fired by coal - Rest on request. licence of Swedish System

Hard rock slab, granite slab, granite block Hard rock block, angle block precisely machined on all sides Measuring cube length: 1590 mm width: 300 mm Height: 470 mm- 2 holes 80 mm- 2 holes 120 mm - threaded bushes mainly M16, some with M12 and M18 Net weight: 570 kg good condition; used

Hard rock slab, granite slab, granite block, measuring cube Hard rock block, angle block precisely machined on all sides The granite top comes from a measuring machine Dimensions of the large table surface L x W x H: 1350 x 1000 x 300 mm Dimensions of the small table surface L x W: x H: 1350 x 300 x 245 mm- 5 pieces of shelter blocks with levelling screws approx. 400 mm- 8 pieces of threaded bushings in the table surface with M10 (hole spacing 500 x 250 x 250 x 250 mm) - 4 pieces of threaded bushings M16 - small chipping on the edge of the plate Overall dimensions L x W x H: 1350 x 1350 x 300 mm Dead weight measuring plate: 1500 kg Dead weight granite feet: 100 kg very good condition; used

Excavator buckets / rock bucket, very stable, unused The geometry corresponds to a Fang, the tooth holder / cutting edge is rounded, this high performance, grave. Bucket width: 1500 mm Bucket volume: 1 m 3 (piled) base plate for quick coupler: 520 mm (width) x 640 mm (depth) Excavator size: 18-30 to use weight

Hard rock - test plate, stone measuring plate, granite measuring plate, measuring table PAGUS DIN 876 Working surface: 630 x 400 mm Working height: 920 mm Material: IMP with base cabinet: 510 x 360 x 700 mm with key used, tested ! Dimensions: 630 x 400 x 920 mm

RECON Part number: 1218-5513 Please note: we also have other various RECON parts of different manufaturers / types in stock. We are pleased to provide you with our current stock list. ---------------------------------------------------------------------- ----------- If you have any further questions do not hesitate to contact us

conventional haertepruefer for the Processes Rockwell C , B , A Analog measuring watch, manual operation, weight load system Standard compliant according to ISO6506 Performance 2 years At the price, no used hardness tester is worthwhile. Better to spend a little more, but with a guarantee. More info schuetz-licht.de/produkte/haertepruefer/haertepruefgeraete-rockwell/ha ertepruefgeraet/

WK 700 Z classic Tilting circular saws Tilting saws/firewood saw PTO Performance: Tractor approximately 12KW - 16 HP Speed: 1450 RPM with the carbide saw blade 700 / 30 mm with longitudinal stop Depth of cut: D = ca. 250 mm with drive systems Weight: ca. 120 kg G & BGU-90157 Accessories: G & BGU-91272 wood retaining claw G & BGU-95060 PTO PTO standard 102

HWS 720 K Tilting circular saws Electric motor with direct drive Saw blade diameter: 700 mm Speed: 1400 1/min 400V 50 Hz Working height: 850-1150 mm Rocker pad: 735 mm Dimensions: 1270 x 730 x 1130 mm Weight: 100kg G & PIECES 5965721

Width: 1000 mm Length: 1500 mm Plate height: 195 mm Adjustable feet height: 600 mm Total height, working height: approx. 800 mm weight:

Immediately available used

SMA 700 Rocker saw Firewood saw Battery starter G&JAN-1055006

Weibert SMA-700T Rocker saw PTO drive Tractors power min. 15hp PTO speed: max. 540 rpm Drive saw blade: belt drive Saw blade speed: max. 1440 rpm Saw blade diameter: 700mm Carbide-tipped Holder 30mm, tooth pitch 32mm, thickness 3.2mm Total weight 136kg Dimensions: 109mm x 85mm x 110mm (LxWxH) G&JAN-1055004

Motor power: 179kW, length: 9655mm, width: 2490mm, height: 2630mm, weight: 18.7t, with documentation.

RECON rocker arms complete with rocker arms MAK M43C MAK Part Numbers: 433530-100, 433510-100, 433520-100

BERGEN ROCKER ARM. BERGEN BRM, WARTSILA, DEUTZ KHD/MWM, MAN B&W, JENBACHER, ABC, PIELSTICK , GUASCOR, MAK, CATERPILLAR, VOLVO, WICHMANN, PUMPS, SACM, SEPERATOR, COMPRESSSOR, FILTER, PUMPS, VACUUM SAVAGE SYSTEM, HEAT EXCHANGER & COOLER. Spares are available and all kinds of spare parts can be given. Please contact us for your questions. EVE International AS E-Posta : info@eveinternational.com.tr Phone : +90 0216 519 2707 Fax : +90 0216 519 2720

Diameter x width: 750 x 1,500 mm max. operating pressure 300 bar Weight: approx. 2,800 kg 76 Chisel

Immediately available used rocker arm bracket

Immediately available used rocker arm block.

Immediately available used rocker arm bracket

Immediately available used rocker arm bracket

Immediately available used rocker arm bracket

Immediately available used rocker arm bracket

Description: Measuring plate 1000 x 600 x 140 mm Including base cabinet and vernier height gauge on the measuring plate Attention: without paints, varnishes and liquids weight approx.: 300 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 630 x 1,400 mm

weight approx.: 300 kg, Approx. Onsite Dimension. (l x w x h): 1,200 x 400 x 250 mm

Description: Including base frame , weight approx.: 200 kg, Approx. Onsite Dimension. (l x w x h): 1,000 x 600 x 900 mm

Description: Reading 0.5 HR. Ball and diamond indenter. N.5 setting blocks (3xHRC, HRBW, HRA). Max measurable height when the lead screw protector is added 100 mm, without a lead screw cover 170 mm. Measurement depth 135 mm. Durometer dimensions 185 x 465 x 640 mm. Measuring force: 588,4 N (60 Kgf) /980,7 (100 Kgf) /1471 N (150 Kgf). The item that is delivered is NOT the one shown in the pictures, but an equal one Approx. Onsite Dimension. (l x w x h): 530 x 400 x 750 mm, weight approx.: 82 kg

Many of our machines are available from stock. Call and ask to find out more. Hydraulic press brake PBE-1204-CNC STEP ROCK22+ Specifications - Max working thickness (S235): up to 3.0 mm - Nominal pressure: 400 kN - Max working length 1250 mm - Throat depth: 300 mm - Max stroke: 210 mm - Daylight: 410 mm - Distance between side frames: 2600 mm - Max backgauge distance: 750 mm - Nominal motor power: 2.0 kW - Length: 1960 mm - Width: 1450 mm - Height: 2610 mm - Weight: 4000.0 kg Tools - Automatic backgauges on linear guides driven by servo: 2 pcs - Front supports: 2 pcs - Backgauge distance regulation (X-axis): electric motor - Ram control (Y-axis): electric motor - Type of punch holder: AMADA quick-action clamping Assistance by a specialist We make sure to stay in constant touch with our Clients. This is why we add a time package of tech support hours for Otinu ...

With articulated carrier DC26, load: 108kW, max. driving speed 16km/h, tyre size: 14.00 R24 A, 2x drill arm BUT 35, Diesel Power Generator Deutz BF4M 1013C, drill mounts BMH 6414, max. drill rod length: 4321mm, max. drilling depth: 4020mm, loading platform HL 210, CE standard, air/water flushing, heat exchanger and high-pressure pump Swellex, without drill hammers.

Commercial Joint Pre-Roll Machine for Condition: very good / NEW FEATURES 72, 143 or 453 Pre-Rolled Joints Significantly Faster Than Competitors Durable & Built for Commercial/Industrial Use Food-Grade Components Designed, Manufactured & Assembled in the USA OSHA Compliant

SUB: FOR SALE... NEW & RECON ORIGINAL PARTS L 48/60 AT STOCK HAVE A GDY SIR; WE'VE MANY NEW OR RECON SPARE PARTS OF MAN L 48/60 AT OUR STOCK. PLS FIND DTLS AT BELOW. MOST OF THEM SUPLIED FROM YOU IF YOU INTEREST PLS DO NEED HESITATE TO CONTACT WITH US. 1 NEW CYLINDER LINER X 1105003-7519 1 YOU 2 RECON EXHAUST VALVE 1140441 D 449216 1 3 RECON EXHAUST VALVE 11408100120560 1 5 RECON EXHAUST VALVE 114071002050560 1 6 RECON EXHAUST VALVE 1140441144 1 7 RECON EXHAUST VALVE 114071000960560 1 8 RECON EXHAUST VALVE 114061002560560 1 9 RECON EXHAUST VALVE 114091003053060 1 10 RECON EXHAUST VALVE 114071009960560 1 11 RECON EXHAUST VALVE 114091000500560 1 12 RECON EXHAUST VALVE 114071000950560 1 13 RECON EXHAUST VALVE 11406102640560 1 14 RECON EXHAUST VALVE 11408100120560 1 15 RECON EXHAUST VALVE 61953016796 1 16 RECON EXHAUST VALVE 6051953004859 1 17 RECON INLET VALVE 01 ...

TECHNICAL SPECIFICATIONS Manufacturer: Weserhütte Description: Double Knee Lever Jaw Crusher Type: DBS1200x960 Year of construction: 1979 Version: Heavy version for hard rock Drive power: 110 kW Flywheel diameter: approx. 2,400 mm Inlet opening (width x height): 1,200 x 960 mm SPECIFIC COMMENT - Incl. pusher SW1250x4000 - Incl. stepped grate with pre-screening - Incl. control unit TECHNICAL SPECIFICATIONS Manufacturer: Weserhütte Description: Double toggle jaw crusher Type: DBS1200x960 Year of manufacture: 1979 Version: Heavy duty for hard rock Driving power: 110 kW Flywheel diameter: approx. 2,400 mm Inlet opening (width x height): 1,200 x 960 mm SPECIFIC COMMENT - Incl. step grate with pre-screening - Incl. control unit If you are interested please let us know, we appreciate to send you a detailed quotation. EuroConsult Dimitrios Piretzidis

Powder incineration furnace 2,000 x 1,900 x 2,000 mm 1 inner dimension length 2,000 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 1 pc. 5,700 m3/hr 10 Electric motors 1 pc. 2.2 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 33 kW = 28,380 kcal/hr 12 sash doors on one side 2 pcs insulated with rock wool 100mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX with heat-resistant fans and heat-resistant bearings, Thermoblock has overheat protection 14 Burner 1 pc. furnace is operated with gas burner 15 Exhaust air 1 pc. device for exhaust air pipe, manual flap guide

Powder incineration furnace 2,000 x 1,900 x 2,000 mm 1 inner dimension length 2,000 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 1 pc. 5,700 m3/hr 10 Electric motors 1 pc. 2.2 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 33 kW = 28,380 kcal/hr 12 sash doors on one side 2 pcs insulated with rock wool 100mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX with heat-resistant fans and heat-resistant bearings, Thermoblock has overheat protection 14 Burner 1 pc. furnace is operated with gas burner 15 Exhaust air 1 pc. device for exhaust air pipe, manual flap guide

Powder incineration oven 3,500 x 1,900 x 2,000 mm electric 1 inner dimension length 3,500 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 1 pc. 7,500 m3/hr 10 Electric motors 1 pcs. 3 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 58 kW 12 sash doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heating electrically heat-resistant fans and heat-resistant bearings, thermoblock has overheat protection 14 Burner 1 pc. oven is electrically heated 15 Exhaust air 1 pc. device for exhaust air pipe, manual flap guide

Powder incineration furnace 3,500 x 1,900 x 2,000 mm gas operation 1 inner dimension length 3,500 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 1 pc. 7,500 m3/hr 10 Electric motors 1 pcs. 3 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 58 kW = 49,880 kcal/hr 12 sash doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX with heat-resistant fans and heat-resistant bearings, Thermoblock has overheat protection 14 burner 1 pc. oven is heated with gas burner. 15 Exhaust air 1 pc. device for exhaust air pipe, manual flap guide

Powder incineration oven 4,500 x 1,900 x 2,000 mm electric 1 inner dimension length 4,500 mm 2 Inner dimension width 1,900 mm 3 Inner dimension height 2,000 mm 4 Substructure 1 set steel profile 5 walls 1 set on both sides galvanized sheets 1mm, outside RAL 6 insulation walls, ceiling 1 set of rock wool 150mm 75Kg/m2 7 ground furnace gets 2 entry rails for horde wagons 8 Temperature 220°C 9 fans 2 pcs. 2x 5,700 = 11,400 m3/hr 10 Electric motors 2 pcs. 2x 2.2 kW , 1450 R/m, 3 F, 50 Hz 11 Thermal power 74 kW 12 sash doors on one side 2 pcs insulated with rock wool 150mm 75Kg/m2 Heating Indirectly via Thermoblock 13 Thermoblock 1 set stainless steel INOX AISI 316 heating electrically heat-resistant fans and heat-resistant bearings, thermoblock has overheat protection 14 Burner 1 pc. oven is electrically heated 15 Exhaust air 1 pc. device for exhaust air pipe, manual f ...

Thyssen measuring plate / control plate made of natural hard rock Thyssen measuring plate made of hard rock (granite slab) Length: 2750 mm Width: 700 mm Thickness: 200 mm Total height with table: 1200 mm Height vertical plate: 240 mm Thickness: 200 mm 2 x T-groove Flatness tolerance according to DIN 876/0 Base with cabinet Trimos HGL 2000 length measuring instrument without measured value display Item location: 42859 Remscheid Dismantling and transport by the buyer. The dismantling, loading, as well as transport can alternatively be offered by us. More measuring plates in other sizes - new and used - can be found in our shop! International shipping costs on request!

Thyssen measuring plate / control plate made of natural hard rock Thyssen measuring plate made of hard rock (granite slab) Length: 4000 mm Width: 1500 mm Thickness: 300 mm Flatness tolerance according to DIN 876/0 Target value 20 μm Actual value 19.5 μm Underframe Item location: 42859 Remscheid Dismantling and transport by the buyer. The dismantling, loading, as well as transport can alternatively be offered by us. Find more measuring plates in other sizes - new and used - More measuring plates in other sizes - new and used - can be found in our shop! International shipping costs on request!

1. ELECTRICAL BOX TYPE OVEN Purpose of use : Powder curing Maximum temperature : 220ºC The furnace heating system is designed as forced convection system. It is based on the principle of pumping the oven volume air into the oven with the help of a circulation fan and increasing the oven temperature with the heat transfer provided by the air passing through the heating unit. The walls of the furnace and heating unit are made of modular sheet metal and high density insulated panels. Air distribution ducts with regulated flaps inside the oven ensure that the oven temperature is homogenous at every point. The temperature control device is digital type and provides precise adjustment of the oven temperature. The heating unit is placed on the side, rear or top of the oven and consists of an insulated heating chamber, heating cell with resistance inside, circulation fan that can opera ...

Hommel Dura Measuring Plate / Control Plate made of Natural Hard Rock Hommel Dura Hard Rock Measuring Plate (Granite Plate) Length: 3000 mm Width: 1000 mm Thickness: 300 mm 1 x T-slot You can find more measuring plates in other sizes - new and used - in our shop! International shipping costs on request!

1. ELECTRICAL BOX TYPE OVEN Purpose of use : Powder curing Maximum temperature : 220ºC The furnace heating system is designed as forced convection system. It is based on the principle of pumping the oven volume air into the oven with the help of a circulation fan and increasing the oven temperature with the heat transfer provided by the air passing through the heating unit. The walls of the furnace and heating unit are made of modular sheet metal and high density insulated panels. Air distribution ducts with regulated flaps inside the oven ensure that the oven temperature is homogenous at every point. The temperature control device is digital type and provides precise adjustment of the oven temperature. The heating unit is placed on the side, rear or top of the oven and consists of an insulated heating chamber, heating cell with resistance inside, circulation fan that can opera ...

Niton XRF equipment, model XL3t 980 GOOLD+. the spectrometer is practically new as it has been completely overhauled and recalibrated by the parent company in November 2023, changing the defective/worn parts which are under warranty for another six months or a year and which has the double metal/alloy -soil/rock setting. (each setting is worth 3000 euros) Overhauled by the manufacturer in November 2023, excellent conditions, comparable to a like new instrument. It is one of the most advanced models capable of reading even light metals such as aluminum, magnesium, silicon and precious metals. The equipment was purchased in Italy from the American company Thermo Fisher, to carry out tests which have now been completed. The spectrometer works perfectly. Reasons for sale: non-use. The equipment has a double configuration, both for soils and rocks and for alloys and metals. Th ...

Year of construction 1994 Stack mass: Depth - 2.40 meters High - 3.00 mtr Long - 11.50 meters Drying capacity - са.75 m3 gross Fans - 7 х 0.75 квт Chamber construction - container construction is not desmantlebel! Interior trim - Aluminium welded 2.0 mm Insulation - rock wool 80 mm Outdoor installation Electrical cabinet with computer control system MB-400 Very good condition

MicroStep CNC guide machine AQUACUT 3001.15 W working area (3000mm x 1500 mm) high pressure pump: KMT Streamline Pro I 60 S, 6200 bar cutting up to 300mm only 4 000 operating hours Including osmosis water treatment system (12,000,- Euro) The AQUACUT is a robust and very practical CNC guide machine in portal construction, specially developed for continuous use in water jet cutting. The high dynamics of the system are overpowered by a low-set machine portal, digital DC servo motors with play-free transmission and practical, stainless linear guides in all three axes. In combination with an HD pump, the AQUACUT can be used to cut solid metals, hard rock, marble, armoured glass, ceramics, plastics, corrugated board, foams, as well as composite materials. assembly and commissioning on request. ; ready for immediate use

Fine impactor, opening: approx. 1,000 x 700 mm, with inlet and outlet box, semimobile on steel skids, for soft and medium hard rock, construction year estimated

Used hammer mill (impact crusher), model 97.58. Overall dimensions: Length 2960 mm Width 2090 mm Height 2065 mm Rotor diameter 0.8m Rotor width 0.6 m Number of hammers 4pcs Max feed grain size To 0.15 m of sedimentary rocks For igneous rocks of 0.20 m Weight Crusher 5.9 T Crusher Capacity 40-70 T / h Main drive 45 kW. Included support frame and spare hammers set. Max rock crushing size 0,15 m sedimenting rocks 0,20 m magma rocks

Used approx. 25 m³ / 25,000 litres Polyester tank , fiberglass tank (Staffelstein tank), above ground, good condition. Dimensions: Ø 2,80 m x 4.20 m high-quality tank on rock/ring, dome on the top of the tank body, multiple ports above, including filling tube and floating indicator. The container can be used as a storage tank for water, liquid feed, whey, potato steam skins, molasses, liquid manure, seeping juice, canola oil, AHL/ASL or as rain drip tank, etc.. Price upon request. Transport can be arranged at low cost. Also we can modify the tank to suit your demands, just ask us. It is not possible to update all our advertisements daily. Since our inventory is changing continuously, it may be that this tank has already been sold but a similar one is in stock. Please give us a call or write, so that we can advise you personally. More information and offers on our s ...

The NEXUS of 7501 is the cheapest universal hardness testing machine with currently available technology: This hardness testing machine sets the benchmark in quality and price in the device class with proven swivel mechanism (motor switch between Indenter and lens): never get a comparably-equipped machine of this quality at such a fair price. In the standard version are already integrated: USB camera + software for the automatic measurement of impression of hardness -electronically controlled test load application with load cell in closed-loop -integrated boxed PC (WIN 7), LAN connectivity, result export, hardness testing software IMPRESSIONS -integrated touch-screen monitor for a simple, direct touch control -LED lighting, Brinell with ring light The machine is universally suitable for all classic metal hardness testing (test loads 0.5 250 kg). Due to the modern, quality equip ...