rep used for sale

Oil-free. Water cooled. Variable speed drive. Volume flow 4.5 - 15.5 m3/min. at 7.0 bar. With built-in compressed air refrigerant adsorption dryer. HP air end 1x replaced. With energy recovery.

ELHA 6 Axis Horizontal Machining Center Xpert-K High-Performance Horizontal Machining Center The newly designed DEPO XPERT K horizontal machining centre offers a high degree of flexibility and above-average productivity. Description Horizontal BAZ The 6 axes are individually controllable. The HSK 100 holder makes it possible to clamp large tools and thus process large areas with high chip removal. Installed is a high-performance G30 fork head spindle with hydromechanical clamping system and a hybrid slewing bearing at top speed which allows extremely high speeds to be driven in order to achieve an optimal milling result even with the smallest tools. This fork head is equipped with a fully automated spindle change cycle, which makes it possible to replace the complete spindle in less than an hour. A hydraulic clamping device is installed for clamping components (effective table ...

KAWASAKI YF03N ULTRA HIGH SPEED DELTA ROBOT The Y Series robots are parallel type pick & place robots and offer quality and reliability. Brand Kawasaki Type YF03N Year of construction 2010 Serial number YF0030012 Electrical connection 400 V Total dimensions L 2400 mm Total dimensions W 2350 mm Overall dimensions H 2750 mm Description of the Kawasaki YF03N robot Type Parallel Kinematics Degree of freedom (axes) 4 Maximum payload (kg) 3 Positioning repeatability (mm) 1 ± 0.1 Range of motion (mm) ø1,300 × H500 Weight (kg) 145 Angle repeatability (°) ± 0.1 Cycle time (payload) 2 0.27s (1 kg) 0.45s (3 kg) Other: 400 volts; camera; Software; instructions; components; Iron frame, with control cabinet; 2x connection cable 5-pin; Control panel E40E-A003

Stable production machine, peak width 1000mm Peak height 180mm Grinding wheel diameter 500 mm ready for use. We specialize in the revision of grinding machines, and offer service, maintenance, repair, conversion and control modernization.

Overhaul year 2020 Built 1995-2019 Saw blade 160 - 200 mm Drive power saw motor 2.2 KW Speed Saw blade 1,500 -3,750 min-1 Cutting speed Saw blade 750 - 3350 m/min Saw height control infinitely adjustable fully electronic Working area square 90° max.: 50 x 50 mm Working range flat 90° max.: 110 x 50 mm Working area Around 90° max.: 50 mm Supply length Pneumatics 2.5 - 350 (single stroke) 5 - 700 (double stroke) Supply length AC Servo 2.5-9999 mm (optional) Supply supply. Servo-controlled replenishment unit 500 mm/s Compressed air connection 6 bar Weight (saw) approx.: 600 Kg Dimensions LxWxH (saw without attachments)approx.: 1400mm x1000mm x1600mm Technical Description Pressta Eisele Profilma 200 Retrofit Pressta Eisele Profilma 200 Retrofit Fully automatic high-performance sawing machine for non-ferrous metals and material The machine is technically as well as ...

Fanuc LR Mate 100i High Speed Robot with Control It is a five-axis, modular, electrically servo-driven robot designed for loading and unloading precision machines, welding and material transport. Its hollow joint construction encloses the entire cable routing to avoid getting stuck. The FANUC LR Mate 100i also features brushless AC servo motors that minimize motor maintenance, sealed bearings and drives enable operation in harsh factory environments. Included in delivery is the control unit Mate RJ-2 Robot Specifications Axles: 5 Payload: 3kg H-reach: 620 mm Repeatability: ±0.04 mm Robot mass:32kg Movement speed of the robot J1 180 °/s (3.14 rad/s) J2 180 °/s (3.14 rad/s) J3 225 °/s (3.93 rad/s) J4 216 °/s (3.77 rad/s) J5272 °/s (4.75 rad/s) Robot Motion Range Robot J1 ±160° J2 +150° - 35° J3 +206° - 159° J4 ±120° J5 ±200° (Changes and e ...

Machine weight: 39,000 kg Faceplate diameter 2000 mm number of supports: 2 pcs. Dimensions : Height 6280 mm width 6600 mm length 4800 mm Extras: Right support with turret head, left and side - sliders. Digital indication of NS 114. Technical condition at the time of sale: Defective rotary amplifier main drive-replacement is required. Require replacement of cables and wires external piping:-machine control cabinets. Repair and adjustment of electrical parts. Not operated since 1994 The maximum dimensions of a workpiece Height 1300 mm Diameter of 2000 mm Weight 15 000 kg

We offer replacement and wear parts for all common scrap baling presses of German manufacturers, such as Lindemann, Becker & Prünte, Becker, Oberländer, Leimbach.

Variable speed drive. Volume flow 2.0 - 14.68 m3/min. Air end 1x replaced. With energy recovery.

Trackball with connection cable for Ultimax control Replacement for Hurco Ultimax 4 , Ultimax 3 Easy to change, ready to ship New

Bosch Scara SR 800 swivel arm robot incl. control Manufacturer: Bosch Maximum load on the gripper flange: 5 kg Stroke 3rd axis 480 mm Pn.-Duuck 4-8 bar Weight: 100 kg Swivel range see diagram, incl. complete control consists of Bosch MP 30 control panel + TR12-R + equipped plug-in card module Item condition used The robots were all in stock at a large automotive supplier as a failure replacement machine, so you are accordingly they are in very good condition. In addition to about 50 paternosters, countless other machines such as presses, robots, furnaces, industrial vacuum cleaners, etc. are available. Workshop equipment, workbenches, workshop trolleys, tools, forklifts and shelves abundantly available A total of 24,000 m² of production space will be dismantled and sold Please also note our other offers.' After purchase, the amount is due within 7 wo ...

PressOne P1S-5 is a press-fit machine from Finland that is powered by a ball-circuit spindle with servo motor. This gives you the best of both worlds. Power, speed and accuracy. No oil means no leakage problems, no rush of oil changes and no filtration problems. Only pure power, accuracy and speed! Specifications: P1S-5 Main press technology: ball-circuit spindle with AC servo drive Maximum pressing force: 50 kN Repeatability of the force adjustment: . . . . . . . . . . . . . . . . . Maximum opening speed: 50mm/s Approach speed: 50 mm / s Pressing speed: max 10 mm / s Extension: 470 mm Stroke length: 210 mm Faster range: M2 - M10 Servo motor: 0.6 kW Control: P1S TC12 Touchscreen 12" Tool connection: Type Haeger, 4-fold lower rotary base The maximum approach speed requires the "Fast Approach Speed" option. Control features of the P1S TC12: - Programmable pressing f ...

Used, partially repaired, tested truck engine in exchange The old part deposit in the amount of 2,500.00 Euro will be credited again regardless of the condition of the old engine 6-month warranty Price plus VAT and shipping

Ceetec's new A250 paint machine is here! As an official and exclusive sales partner for the German-speaking region, I am pleased to present our latest model to you. After almost 50 years of construction of the previous model since the beginning of the 1970s (better known as the GORI brush machine), the new model is now an extensive update with extended applications. Who is this machine suitable for? - Carpentry /carpentry that manufactures carports, facades, terraces, garden houses, etc. - Wood industry companies that paint, read or impregnate industrial boards / beams / slabs etc. Technical data: max. workpiece height: 250mm max. workpiece width: 250mm (or 380mm = Ceetec A380) Speed: 16-42m/min Connection: 400V / 1.5kw Benefits ggü. simple spray painting: 1. The wood protection is massaged evenly into all pores, which ensures a high resistance. 2. Different su ...

AT-Motor, repaired according to RAL-GZ 797 Complete motor, version biogas Four-stroke petrol gas engine (54 kW) 4 cylinders in series water-cooled engine cooling water-cooled exhaust pipe Old part deposit: 6,000 euros

working range without repositioning X: 2535 mm working range Y: 1300 mm Control: Siemens Sinumerik 840D Punch power: 220 KN Laser power: 2200 Watt Plate thickness max.: 8 mm Beam on: 4.390 h Standard equipment: - Work range X-axis 2535mm for combined operation - Hi-Las high pressure cutting - Laser-cutting head with 5’’ lens - head quick change device - Programmable cutting gas/Pressure settings - Capacitive height regulation - Compact dust extractor - 2 sheet clamps - automatic tool change with 19 stations (21 minus sheet clamps) - Full rotation of all tools - NC-controlled, maintenance free 3-phase motor - Repositioning device - quick shut-down of hydraulic system - automatic machine shut-down - tool length compensation - chutes for parts 500 x 500 mm - punching slug suction system - metal forming possible - tool spray lubrication - Programmable stripper - adaptive stroke lengt ...

Package from one place in germany: Printing machine: ABDICK 9840 Plate size: 330 x 492 Kompac dampening system Mirror roller Squeegee unit for coloring (new) Printing and impression cylinders must be readjusted plus material: 1 blanket new 100 printing plates Printing machine: ABDICK 350 cd Plate size: 254 x 381 Kompac dampening system 1 new application roller (reserve) Folding machine: GRAFIpli 3810 S Tools: 2 folding pockets 1x grooves / grooves Perforate 2x Counter: FKS series 3800 Sorting unit: Duplo DC-10 mini Gathering up to 10 sheets of A3 Stainless steel table vertically / horizontally adjustable Stapling unit: NAGEL Foldnak 8 Brochure Street (up to 10 sheets DIN A3) Trimmer: NAIL Cutting machine: EBA 551 LT Extension: Side table left (NEW - not complained) plus replacement knife with assembly tool Package Price: on request

working range without repositioning X: 3085 mm working range Y: 1740 mm Control: Siemens Sinumerik 840D Punch power: 220 KN Laser power: 2400 Watt Plate thickness max.: 8 mm Beam on: 2.763 h Standard Equipment: - Working area for combined laser/punching 2585 x 1650 mm, for punching 3085 x 1740 mm, laser-cutting 3085 x 1650 mm each without resetting operation - HI-Las High pressure nitrogen cutting - laser head with 7,5 lens - programmable repositioning cylinders - quick stop function - Blow-out device for small parts - Safety light barriers - manual Additional equipment: - additional clamp and possibility to open one or a pair of clamps - Prepared for Multitool - Function tapping Automation: - TRUMALIFT SheetMaster FMC - sucker plate - Trumasort L - TRUMATOOL 40 - TRUMAGRIP New Resonator in 2011

working range: 1270 x 1270 mm Punch power: 180 KN Plate thickness max.: 6,4 mm Standard equipment: - Rotatable tool adapter - Autom. repositioning device with presser foot - Autom. Tool changer with 9 stations - 2 clamps - 9 cartridges - Part chute 200 x 200 mm with parts sorting into 2 containers - 2 part container - Brush tables - Multitool - Vaccum slug removal - Chip container - Rapid shutdown device hydraulic - TFT colour screen 10.4 - 3,5 disk drive - Graphic programming ToPs 2000 - Safety light barrier 2 radial - BNC and RJ45-network connection Additional equipment: - Function Tapping - Function engraving/rapid beading - Tool spray lubircation - Table extensions - Tool setting aid

X working range max .: 3000 mm Y Working range max .: 1500 mm Z working range max .: 115 mm Control: Siemens Sinumerik 840 D SL Laser power: 5000 W Beam on: 29.712 h Plate thickness St. Max .: 25 mm Plate thickness Va. Max .: 20 mm Plate thickness Al. Max .: 20 mm Standard Machine Specification: Machine - working range in 3000 x 1500 mm - Closed machine - Integrated cabinet - Optional barrier-free installation - Automatic pallet changer in longitudinal direction - Torque drive in combination with direct linear drives - Enclosed beam delivery via fiber optic cable - Chiller for machine cooling - Integrated electrical cabinets with inside light - Common ON-OFF Switch for machine and laser - Conveyor belt for small parts / slug - Work area lighting - Positioning laser diode - Spray device - PierceLine - FocusLine - NitroLine - PlasmaLine - Automatic nozzle cleaning - Transport and assem ...

working range without repositioning X: 2500 mm working range Y: 1270 mm Control: Bosch PNC-P Punch power: 165 KN Laser power: 3000 Watt Plate thickness max.: 6 mm Standard configuration Machine - Working Range 2500 x 1270 mm - Stable C-frame for easy access - Coordinate guide for high precision machining - Linear magazine with 19 tool stations including and 2 clamps - Drives with maintenance-free 3-phase servo motors - Repositioning unit with programmable stripper - Brush tables - Parts chute 300 x 500mm - Chip container - Good parts container - Enclosed beam delivery via fiber optic cable - ContourLine - FocusLine - NitroLine - Seperate main switch machine and laser Punching head - Hydraulic punching head - Programmable presser foot - Tool length compensation - Spray lubrication for punches - Vacuum slug removal - forming Control - Open controller based on ...

1 pc flame pretreatment system with electronic control 1 pc EF 600-1 Burner control consisting of Electrical control with ignition and monitoring device for 1 pc burner, control electronics, control panel with plain text display, Emergency stop setup and interface for external control Mechanical control with Safety valves, gas/air mixers, thermoanemometrial mass flow meters for air and gas, Engine valves, pressure monitors for overpressure and vacuum monitoring and supply air blowers. 1 pcs C24-2300 Film burner, 2200 mm working width, adjustable up to min. 1000 mm with connections for water cooling and water-cooled double T-beam 1 pc spare parts consisting of 2 earth replacement electrodes and 1 replacement fabric Power supply : 400/230 V 50 Hz, 2.5 kVA Gas supply : Natural gas 75 – 100 mbar Heat output : max. 400 kW Gas consumpt ...

M. No .: 45553I // Output: max. / min mechanical: 9000 copies / h // 2000 copies / h Formats: trimmed max. / min .: 30.5x34.9 cm // 8.9x14 cm Untrimmed max. / min: 31.1 x 35.5 cm // 9.2x14.6 Product thickness max. 1.0 cm pressed Consists: Feeder: 3x double vertical feeder (DVA 100) total 6 Stations // Gripper opening for folded sheets with pre-and post-fold (min.0.5 cm) vacuum opening without overfold / combined gripper. Stitching station: 2xHohner Universal 52/8 Trimmer Scale display Pressure vacuum generator Equipment / Additional information: -Compl. Replacement knife set -middle cut -1x replacement stitching head -Replacement chains -Finger + tongues - Conveyor belts changed 4 years ago Power supply: 50/60 Hz // 3x380 V (420) // 3x220V (200)

Variable speed drive. Volume flow 12.4 - 50.5 m3/min. at 7.0 bar. Air end 1x replaced.

Used Heuft Glass Empty Bottle Inspector InLine reflexx Device No. 2ZG042943 Condition: very good, ready for use at short notice ·       Original delivery date 12.2011 ·       Power max. 46,000 fl./h ·       Pass direction from left to right ·       Two triggers ·       Secomak blower instead of compressed air ·       Transponder detection for RFID test bottles ·       Discharge monitoring ·       Network Heuft Hlan (Upgrade Optional) ·       Hayt two ways discharge Delta K to the right ·       4 Variety Licenses ·       Tripartite Delta K for band height of 1130 ·       Two fluids for lye detection Not available! ·       inlet control, must be supplemented if necessary ·       Thread edging, must be supplemented if required ·       The documentation is complet ...

SHARK 281 CCS (Cut Control System) manual bandsawing machine to cut from 0° up to 60° left. Other than the manual cut mode, the sawing machine can make single cuts without operator, using the head weight control- led by a hydraulic brake: after the cut the band stops. The frame at this point is manually lifted to the position needed in order to reposition the bar to cut . In the version with pneumatic vice (MA) the vice is opened/clo- sed by a manually-controlled valve (optional with pedal control). BEST PRICE IN EUROPE

The FORNI INDUSTRIALI FIBEX COMBI 6GX-10.130-7110.2E.270 brazing furnace was built by the Italian company Forni Industriali Heat Treating Plants in 2007. The furnace is used for soldering steel elements with solder paste at temperatures up to 1120 degrees Celsius. At the entrance and exit of the furnace, two pairs of gas burners (so-called safety pilots) are installed to prevent the escape of the protective atmosphere outside the furnace. Electric heaters powered by thyristor temperature regulators are responsible for the proper temperature in the furnace. The belt furnace has a conveyor speed adjustment in the range from 0 to 500 mm / min, and the working length of the soldering zone is 7100 mm. The furnace for brazing steel elements was modernized in 2021 - the thermal insulation and the cooling module for sections 1 and 2 were replaced. The cost of the modernization was 70,000 Euro.  ...

Accuracy: 0.7 mm Application: Production and montagelinins, quality control Location: Rüsselsheim The measurement is based on the analysis of surface curvature. The deformation is detected by the detector built into the scanning head. During the measurement, the image of the detector is converted into a point cloud using the control software. Each of the points describes the geometry using X, Y, Z coordinates. The system then enables personalized analysis and reporting. The scanners can also be purchased individually. Visit by appointment. Disassembly, transport and commissioning by specialist company optionally possible.

In our depot in Freilassing we always have new containers in different colours and finishes in stock. This ensures a short delivery time and the possibility to visit the containers before purchase. CHOOSE YOUR CONTAINER! PrimeQUALITY As a very special service we offer the option to buy a flawless first-trip container. For this purpose, transport damage is professionally repaired and dirt is removed. State New / First trip – with easy traces of usage through one-time sea voyage Color Bottle breakfast RAL 6007 (or subject to availability) TECHNICAL DATA Dimensions outside: (L x W x H) 6,058 x 2,438 x 2,591 mm Dimensions inside: (L x W x H) 5,844 x 2,330 x 2,350 mm Weight: approx. 2.22 t Payload: approx. 28.27 t Facilities CSC Safety Approval Material: CorTen steel, weatherproof Floor: 28mm hardwood, waterproof Doors: 270° opening, 4-fold linkage Coating: insi ...

Robot Industrial Robots KUKA Kuka KR60-3 F Foundry Built in 2006 Reach 2033 mm Weight 665 kg Payload 60 kg Kuka Control KRC2ed05 Weight 185 kg Processor 2GHz Language WinXP Software status V5.6.8 Kuka Teachpendant KCP2ed05 Kuka interconnectors 7 m / 15 m repainted

Used shredders with gearbox not overhauled and also not repaired. Spare parts such as shafts, scrapers, knives, etc. also available as good as new.

Thermotron Temperature Chamber Here we offer you a Thermotron temperature chamber. Water-cooled Thermotron temperature chamber SE-1000-5-5 Dimensions of the working area - WxDxH: 102 x 100 x 97 centimeters Working range volume: 986 liters Temperature uniformity: ± 0.5°C Temperature range: -70ºC to 180ºC Temperature control tolerance: 0.3°C Feed dimensions - WxDxH: 122 x 188 x 218 centimeters Electrical requirements 400/3/50 28.4 A Refrigerant: R-404A / R23 Approx. Weight: 862 kg Type: Thermotron SE- 1000-5-5 For you as a buyer for security the following information! The following points are carried out in advance at our offered chambers: 1. Functional check and replacement of necessary components 2. New filling with legally compliant refrigerant 3. Leak test with certificate 4. After successful verification, the chambers are subjected to a test run, which ...

Robot Industrial Robots KUKA Kuka KR60-3 Built in 2005 Reach 2033 mm Weight 665 kg Payload 60 kg Kuka Control KRC2 Weight 185 kg Processor 733MHz Language Win95 Software status V4.1.7 SP08 Kuka Teachpendant KCP2 Kuka interconnectors 7 m / 15 m (repainted) Can also be offered with a KRC2ed05 controller Kuka Control KRC2ed05 Weight 185 kg Processor 2GHz Language WinXP Software status V5.6.6

White Temperature Test Chamber Here we offer you a white temperature test cabinet. White temperature test chamber air-cooled approx. 124 liters Dimensions and design of the test chamber Internal dimensions Height 490 mm Width 540 mm Depth 470 mm External dimensions Height 1230 mm Width 780 mm Depth 1112 mm Bushings in the side walls: 2 pcs., NW 560mm 1 pcs., NW 100 mm Specifications: Temperature range -40°C to +180°C Temperature change rate Cooling: 2.0 Kimin to -10°C Temperature change rate heating: 2.0 Kimin Electrical connection: 380V/3PH+N+PE/50 Connection value: 4.4 kVA Refrigerant: R-404A Weight: 270 kg Type: 125 SB/+10 JU/40 DU For you as a buyer for security the following information! The following points are carried out in advance at our offered chambers: 1. Functional check and replacement of necessary components 2. New filling with legally compliant r ...

Zalkin capping machine replacement parts Size 35 x 18

Forkilift in good condition, battery dead. Ned be replaced. We can offer As well refrubrished, and price on request. Lifting height 200mm lifting capacity 2000kg

Air table, side tables chrome-plated table Monitor Replacement knife

White Temperature Chamber Here we offer a white temperature chamber. White temperature chamber water-cooled Temperature range: from - 70°C to 180°C Temperature change rate cooling 10 K/min Temperature change rate heating 10.0 K/min Temperature deviation in time ± 0.1 to ± 0.5 K Temperature homogeneity spatially ± 0.5 to ± 2.0 K Test room dimensions: width 580 mm x depth 615 mm x height 750 mm Housing dimensions: width 895 mm x depth 2080 mm x height 1950 mm Voltage: 3/N/PE AC 400V±10% 50Hz Rated power 14 kW Rated current 26 A Refrigerant: R-404A R-23 Weight: approx. 450 kg Control panel has been updated to a 24 volt version Type: WT11-270/70/10 For you as a buyer for security the following information! The following points are carried out in advance at our offered chambers: 1. Functional check and replacement of necessary components 2. New filling with le ...

Espec Temperature Shock Chamber Here we offer you an Espec temperature shock chamber. Thermal shock environmental chamber (cold load: -65° to 0°C). Conventional thermal shock chambers with three zones can be quite large, since three separate chambers are used. The TSA series has only one chamber, which significantly reduces its size. Instead, it circulates cold, hot or ambient air as needed. The air-conditioned air can be pre-cooled or preheated beyond the setpoint, allowing for faster recovery of the desired state after transmission. Espec Temperature Shock Chamber Water Cooled TSA-201S SN: 153000154 Hot chamber: +60 to 200°C Cold chamber: -70 to 0°C Working temperature: 0-40°C System: Two zones or three zones test by flap switching Achievement: Test area: High temperature. Exposure range: +60 to +200°C Low temperature. Exposure range: –70 to 0°C Temperature fluctu ...

Punching machine AMADA Europe 258 Punching force / Punching force 20 ton Working range / working range: 1250mm x 2000mm (4000mm with one reposition. 5000mm or more is also possible with second reposition) Hydraulic-eccentric drive / Hydraulischer Antrieb Turret / Revolver; Total number of 27 stations: Auto Indexing: 2 x B (max dia 31.7mm) 1 x C (max. dia. 50.8mm) Roller table / ball table

The X-MET8000 handheld XRF devices offer high performance for the reliable testing of materials and chemical compositions: fast, precise analysis for fast sorting (metals, polymers, wood, solutions, soil, ores, minerals, etc.). The X-MET is practical, robust and easy to use, for results you can rely on. The X-MET is perfect for the analysis of light elements (Mg, Al, Si, P, S, Cl). It offers the lowest detection thresholds with laboratory-quality results in seconds, day after day. Test a wide range of materials with the versatile fundamental parameter (FP) method and empirical calibrations (traceable to certified reference materials) where the highest precision and accuracy are required. Friendly The intuitive, icon-based user interface requires minimal operator instruction. Excellent ergonomics Lightweight (only 1.5 kg), compact, ergonmomic. You can use the X-MET for a lo ...

The capsule filling machines SPT-FM 100 are for the fully automatic filling of hard gelatin capsules Large #00 - #4, (optionally 000, 5) with powder, granules or pellets in the pharmaceutical and dietary supplement sector Designed. The dosing is carried out via a dosing disc, which ensures a high accuracy of the filling quantity. The new SPT series of fully automatic capsule filling machines enable: Capsule size of #000 - 5 Encapsulation of powders, granules and pellets possible Faster and easy format change without additional tools Touch Screen User-friendliness via HMI (Human Interface) According to GMP guidelines CE-certified 2-year warranty Installation and repair service from Germany Number of segements 14 Max power caps/h 110,000 Capsule size #00,1,2,3,4 (optional #000.5) Max rotation speed 130 rpm Speed control inverter Bczj2ygm3s Machine dimensions 1,650 x 1 ...

Laser handheld spectrometer VULCAN for quick and easy chemical elemental analysis. Vulcan is one of the fastest metal analyzers on the market and is designed for durability. It offers reliable material identification in just one second, based on laser-induced plasma spectrometry, without any X-rays. Whether for scrap sorting or PMI quality control, Vulcan always provides precise and consistent material ID data. Significant increase in productivity An increased number of analyses per day makes all the difference, especially with extensive inventories. Low operating costs Because Vulcan is a laser device, employees don't have to attend expensive and time-consuming radiation training and certification training. Long-lived Vulcan is IP54 certified (equivalent to NEMA3) and meets military standards for robustness (MIL-STD-810G). It also comes with a 3-year warranty. Prove ...

The Capsule Filling Machines SPT Series are for the fully automatic filling of hard gelatin capsules Large #00 - #4, (optionally, 000, 5) with powder, granules or pellets in the pharmaceutical and dietary supplement sector Designed. The dosing is carried out via a dosing disc, which ensures a high accuracy of the filling quantity. The new SPT series of fully automatic capsule filling machines enable: Capsule size of #000 - 5 Encapsulation of powders, granules and pellets possible Faster and easy format change without additional tools Brg2zsee Touch Screen User-friendliness via HMI (Human Interface) According to GMP guidelines CE-certified 2-year warranty Installation and repair service from Germany Number of Segements 1 2 3 Max power caps/h 8500 17000 25000 Capsule size #00,1,2,3,4 (optional #000.5) Max rotation speed 140 rpm Speed control inverter machine dimensions  ...

MAPS devices for grinding and polishing Here we offer a Struers MAPS preparation system. High capacity Less consumables, less work Unique reproducibility Main features for the highest quality and the preparation of high quantities Specifications: Connections: Current: Three-phase Compressed air: 6 bar (90 psi) - consumption approx. 200 l/min Water: Supply via house connection, disposal via house wastewater Size and weight: MAPS preparation modules Height: 1905 mm Length: 1535 mm Depth: 1115 mm Weight: 850 kg Sample Holder Sizes: 160 mm Ø and 200 mm Test holding arm Drive motor: 150 rpm, 0.37 kW (0.5 hp) Pressure force: 50-700 N in stages of 10 N Preparation station for plane grinding Main engine 5.5 kW (7.4 hp) Speed: 1450 rpm Grindstone: Ø 356 mm, grinding width 115 mm Dressing: automatic funnel for the grindstone Circulation cooling unit: 60 l/min, capacity  ...

The capsule filling machines SPT-FS80 are for the fully automatic filling of hard gelatin capsules Large #00 - #4, (optionally s. 000, 5) with powder, granules or pellets in the pharmaceutical and dietary supplement sector Designed. The dosing is carried out via a dosing disc, which ensures a high accuracy of the filling quantity. The new SPT series of fully automatic capsule filling machines enable: Capsule size of #000 - 5 Encapsulation of powders, granules and pellets possible Faster and easy format change without additional tools Touch Screen User-friendliness via HMI (Human Interface) According to GMP guidelines CE-certified 2-year warranty Installation and repair service from Germany Number of segements 10 Max power caps/h 80,000 Capsule size #00,1,2,3,4 (optional #000.5) Nf7il Max rotation speed 130 rpm Speed control inverter Machine dimensions 1,320 x 1,050  ...

Heraeus Vötsch Here we offer you a climate test chamber. Water-cooled Housing dimensions: width 2215 x depth 1280 x height 1985 (mm) Rated voltage: 400V, +-10%, 3/N.50Hz Rated power: 12.5 kW Rated current: 19 A Temperature testing Temperature range -70°C to + 180°C Temperature deviation: +- 0.5 K temporally, +- 2 K spatially Cooling speed on average: 2 K/min Heating speed on average: 3 K/min Climatic test Temperature range +10°C to + 90°C Humidity range: 10% to 98% RH Humidity deviation: +- 1% to +- 2% RH (temporal) Temperature deviation: +- 0.3 K temporally, +- 1.0 K spatially Test room volume: 1200 liters Qualified usable space: 695 x 1190 x 750 mm, approx. 620 liters Refrigerant ND R404A Refrigerant HD R23 Water consumption: < 3 litres / 24 hours (at 40 °C and 92 % RH) Type: HC 7120/S For you as a buyer for security the following information! The fol ...

The capsule filling machines SPT-FM150 are for the fully automatic filling of hard gelatin capsules Large #00 - #4, (optionally 000, 5) with powder, granules or pellets in the pharmaceutical and dietary supplement sector Designed. The dosing is carried out via a dosing disc, which ensures a high accuracy of the filling quantity. The new SPT series of fully automatic capsule filling machines enable: Nf7iv Capsule size of #000 - 5 Encapsulation of powders, granules and pellets possible Faster and easy format change without additional tools Touch Screen User-friendliness via HMI (Human Interface) According to GMP guidelines CE-certified 2-year warranty Installation and repair service from Germany Number of segements 20 Max power caps/h 150,000 Capsule size #00,1,2,3,4 (optional #000.5) Max rotation speed 130 rpm Speed control inverter Machine dimensions 1 750 x 1 750 x 2 ...

White temperature cabinet Here we offer a white temperature cabinet. Air-cooled White temperature cabinet with S! MCON / 32 controller Test room capacity : approx. 195 litres Test room dimensions: height 750 mm, width 580 mm, depth 450 mm, External dimensions: height 1775 mm, width 870 mm, depth 1600 mm, Data for operation: Test room lighting halogen bulb 24V, 50W Rated voltage: 3/N / PE AC 400 V ± 10% 50 Hz Rated current: 14 A Data for temperature tests: Temperature range: -42 to +180 °C Temperature deviation temporally in the middle of the usable space: ± 0.1 to ± 0.5 K Temperature deviation spatially: ± 0.5 to ± 1.5 K Temperature change rate Heating: 4 K/min Cooling: 4 K/min Heat compensation max. 2300 W Refrigerant: R404 A 2.5 kg Gwicht : 490kg Type: WT3 - 180/40 For you as a buyer for security the following information! The following points are  ...

Round-cut heading machine for whitefish Baader IS033 Processes: cod and other whitefish with throat cut Working range: 1-13 kg Throughput rate: up to 30 fish/min Operator: 1 person The fish is placed belly to operator head first into the machine. The fish head is held and the entire fish is transported to the knife section where a high-yield head cut is performed. The main body of the fish, with collarbone on, discharges to the front of the machine. The head is transported via a chute to the rear of the machine. Thanks to its construction, the operator has a clear view of the machine. Adjustments e.g. for adaptations or service operation are performed easily and operator-friendly as well as knife replacement. Technical Data: Water consumption: 10 l/min Power consumption: 2.2 kW Features Maximum yield Easy handling and clean up No size adjustment ne ...