recycling used for sale

CANDY RECYCLING AD 2000 made in 2015 for recycling of Rework from hard candy production suitable also for jelly, toffee, lollies, fondant even wrapped products result after recycling: completely transparent and neutral sugar-glucose syrup-water solution consisting of: dissolving machine intermediate/buffer tank, volume 2000 L with platform horizontal rotary drum vacuum filter unit year 2015 very good condition

Cable recycling plant with many innovations in all plant components for up to 600 kg/hour (depending on material) The basis of this recycling plant is modularly constructed from strong and innovative individual components. In the standard version, the following structure is obtained. - Preshredder MR 4080 or MR 40-100 - Conveyor belt with magnetic separator - controlled by PLC - Granulator C 600 with axle length 600 mm, 5 rotor blades and 37 kW drive, cooling of the housing by unit against adhesions - Z-separator for the separation of heavy copper or 1 granulate - Dosing drum for the optimally uniform feeding of the following turbine mill - Ghibli 545 turbine mill (new model), optionally with coolable housing and inverter control - SA 600 separation table, new version with PLC inverter control of the air volume + eccentric drive with inverter control of the oscillation + adju ...

Used conveyor belt, built in 2020, few operating hours Very heavy design for recycling With very strong neodymium magnet in the upper deflection drum Reducing gear for slow conveying speed With concealed wavy edge and crossbars on the harness Large inlet hopper with adjustable slider for material height on the belt 4 m long, discharge height approx. 2.2 m (variable) Ideal, for example, for feeding material into a cable recycling plant At call

Used, heavy and high-performance recycling plant for the recycling of old cables. The machine has a granulator with a knife length of 500 mm and a large cutting table. As a result, the Sincro 530 from Guidetti achieves hourly outputs of 450 to 600 kg (manufacturer's specs). The system was traded-in by us and all essential components were checked in the workshop. The machine works reliably and trouble-free. On request, the system can be equipped with pre-shredders and conveyor belts. Feel free to visit us and get your own impression of the machine. You are also welcome to test the machine with your cable material.

Technical data single-deck ballistic separator for three separation fractions: Manufacturer Lubo Screening & Recycling Systems B.V. Type Elliptical 10EBB05 Year of construction 2015 Screening area 12.5 m², consisting of 6 screen paddles 400 x 5000 mm Weight 7,100 kg Note on the separation process: The Lubo Elliptical is a state-of-the-art ballistic separator. It separates the material stream into three fractions, heavier 3D fractions such as tin cans or PET bottles, lighter 2D fractions and screened fines. This ensures high separation quality for various waste streams such as mixed waste, packaging, mixed paper, film and cans. Condition of the machine: The Elliptical 10EBB05 ballistic separator is still in use at a large recycling company separating mixed waste until the 18th calendar week, when it will be replaced by a larger machine with a higher throughput capacity. The machine is in ...

Plastics Recycling Extruder PP=900-1000kg Complete Line

Ermafa twin screw extruder B 2.95-35 D 1992/1995 -Extruration plant for recycling -with hot-tee, Filter -Drying centrifuge, -Degassing plant, -storage silo, -discharge silo, -Chain elevator. -900-1000 kg/h PP

To separate and sort after the specific weight from light and heavy fraction. Useable for grain, aluminium/plastic, rubber/textile, cable-recycling, etc. Type and size are choiceable, depending on the product and throughput. At constant machine length, it is possible to choose between working width from: 450mm, 600mm, 900mm.

The JMC 407 is the top seller among our alligator scissors. It is cost-effective, has a sufficient knife length and enough power for most tasks in metal recycling. It is suitable for cutting many materials, such as profiles, pipelines, motors, transmission housings. The scissors are also frequently used for cleaning scrap metals or for cutting vehicle coolers. The machine has a control without electronics and a manually adjustable holder, which also acts as a protective hood. The scissors can be used by foot pedal in single or continuous operation. The opening width is adjustment via simple clamping screws.

Small vibrating sieve with two decks for three fractions. The diameter of the sieve inserts is 400 mm. This includes a bet with balls that keep the screen insert clean from below. This is suitable, for example, for the screening/classification/quality assurance of copper granules (contamination by plastics or aluminium are sifted) or for the re-treatment of plastic granules from the cable recycling. The sieve is located in our demo pool and is little needed.

The IRS 120 Easy is the perfect entry point into cable recycling. The special combination of large flywheels and multi-part segment cutting knives makes it possible to efficiently recycle old cables made of copper or aluminium even without high power consumption and without shredding. The machine impresses with its small footprint, is easy to maintain and easy to use. Compared to most of the competition's systems, the machine has two separate fans for separator air and dust removal. This eliminates the usual interactions between more or less clogged filters and the purity of the copper granules. In addition, the separator air is not roughly adjusted via throttle valves, but by sensitive adjustment of the fan speed. This gives you the best qualities in finished copper. This machine is an immediately available storage machine and has 4 screen inserts, electronic pre-equipment for ...

Small shredder for a wide range of tasks such as old cables, plastics wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). The machine was overhauled by the manufacturer ISVE in September 2020 and supplemented with an electronics for networking into a cable recycling line. A rotor cover for the optimized processing of old cables has also been added. Currently, the shredder has a 16 mm hole sieve but other hole diameters can also be added. With the 16 mm hole sieve, the shredder reaches about 250 kg/hour when processing mixing cables.

Slow-running robust single-shaft shredder Suitable for the pre-shredding of various materials without solid stuttering materials. Application: Crushing of industrial and commercial materials, films, packaging materials, textiles, paper, rubber, demolition wood, pallets, paper rolls, cable drums, mixed plastics for thermal and recyclable recycling, loose or pressed into bales. Lindner Jupiter 3200 Drive power: 2x 160 kW (Schorch motors) Sieve perforation: Sieving 148 mm Control cabinet: complete with ( FUe -P-Drive) Opening: 3190 x 1750 mm Single volume: approx. 8 m3 Rotor length: 3190 mm Rotor flight circle: 745 mm Rotor speed: 50Hz : 58 rpm Number of rotor blades: 36 pieces Knife dimension, pointed knife: 145x 145 x 47 mm Geggenmesser unten: 9 pieces Scraper comb above: 9 pieces Hydraulic feed: 11 kW Weight: approx. 38 t Dimensions LxWxH mm: 6250 x 3260 x 3090(H=4900 m ...

Small floor filter, which can be used, for example, for extracted air from separators in cable recycling. The filter is without its own fan, so it works purely passively. The filter and the collection bags have a diameter of 500 mm.

Used cable recycling plant Tecnoecology T 250 Turbo Year of construction: 2008 The plant consists of the following parts: - Pre-shredder: Bano MAC 630, approx. 250 - 400 kg/hour, depending on material - Conveyor belt to the dosing accumulator, approx. 4.0 m - Dosing accumulator with discharge conveyor, approx. 1.5 m³ - Controlled conveyor belt with belt magnet for feeding the granulator, approx. 4.0 m - Granulator GA 400/30, approx. 250 - 400 kg/hour, depending on material - Turbine mill, T 25-2, built in 2019 - Separator TV 300, inverter controlled, separation table 80 μm - Dust extraction and filter system The entire system currently achieves between 200 and 300 kg/hour in operation, depending on the cable composition. On request, additional components, such as a big bag loading for the plastic or the re-screening of the granules, can be supplied. The plant is curre ...

Young used machine with very few hours of operation. Compact cable recycling plant with low connected load for 80 - 120 kg/hour (depending on material) This system can be operated with a pre-shredder via a conveyor belt as well as in direct insertion. The system still has the original, unground set of knives, so it can hardly have more than 40 to 50 operating hours. Therefore, we offer this system including a 12-month used machine warranty. Pre-shredders, conveyor belts, dosing accumulators, etc. can also be obtained from us.

Heavy conveyor belt for the recycling of old cables or other materials. The 30 cm strap is designed with concealed lateral pleated bars so that no wires or other material can get stuck in the gaps. The 0.75 kW drive motor is also equipped with a reduction gear, which significantly reduces the conveying speed. The conveyor belt is only used a little and therefore shows hardly any signs of wear.

Simple unit for transporting plastic granules, such as PVC from cable recycling. Suction through hopper and 100 mm flex tube. Forwarding by fan/fan in rotary valve for dust removal. By extending the pipes, the unit can also be located further away from the feeding point. The big bags are suspended by height-adjustable chain hooks. The unit consisting of a rotary valve and filter is also adjustable in height. Of course, boxes can also be used instead of big bags. The machine can be inspected and tested with us.

Technical data baler: Manufacturer BOA Recycling Systems B.V. Type Impress D225-165-D-5V/5H-1.6 Year of manufacture 2022 Operating hours 1,486 hours, as of June 2023 Pressing force main press 2,211 kN or 211 t Specific pressing force 17.5 kg/cm² Working pressure 280 bar Press stroke main hydraulic cylinder 2,900 mm Average cycle time 23 seconds Dimensions of feed chute 1,620 x 972 mm Volume of press chamber 4.4 m³ Bale dimensions 1,100 x 1,200 mm, length variable Drive power 3 x 45 kW Total connected load 250 kW, 500 A Tying system 5-fold vertical, 5-fold horizontal, fully automatic Throughput rates with a bulk density of 30 kg/cbm up to 20 t/hour Bulk density of 60 kg/cbm up to 33 t/hour Bulk density of 100 kg/cbm up to 46 t/hour Bulk density from 150 kg/cbm up to 56 t/hour Bulk weight from 200 kg/cbm up to 69 t/hour Bale weights up to 1300 kg, depending on material Hydraulic oil tank ...

Technical data baler: Manufacturer BOA Recycling Systems B.V. Type Impress D225-165-D-5V/5H-1.6 Year of manufacture 2022 Operating hours 1,568 hours, as of June 2023 Pressing force main press 2,211 kN or 211 t Specific pressing force 17.5 kg/cm² Working pressure 280 bar Press stroke main hydraulic cylinder 2,900 mm Average cycle time 23 seconds Dimensions of feed chute 1,620 x 972 mm Volume of press chamber 4.4 m³ Bale dimensions 1,100 x 1,200 mm, length variable Drive power 3 x 45 kW Total connected load 250 kW, 500 A Tying system 5-fold vertical, 5-fold horizontal, fully automatic Throughput rates with a bulk density of 30 kg/cbm up to 20 t/hour Bulk density of 60 kg/cbm up to 33 t/hour Bulk density of 100 kg/cbm up to 46 t/hour Bulk density from 150 kg/cbm up to 56 t/hour Bulk weight from 200 kg/cbm up to 69 t/hour Bale weights up to 1300 kg, depending on material Hydraulic oil tank ...

Lindner Recycling Shredder used., Brand: LINDNER, Model: Universo 2800, Year of construction: 2010, Number of knives: 68 pieces, Knife shape: 87x87x38, Sieve perforation: 128 mm, Rotor speed: 80 rpm, Weight: 26 tonnes, Electric motor: FIG, Power: 132 kW, Spare parts: Cutting blades and others., Warranty: none, Terms of delivery: EXW Germany, Machine is ready for use and can be put into operation quickly at any time., fire: LINDNER, model: Universe 2800, Year of construction: 2010, Number of knives: 68 pieces, Knife shape: 87x87x38, Sieve perforation: 128 mm, Rotor speed: 80 rpm, Weight: 26 tons, Electric motor: ABB, power: 132 kW, Spare parts: Cutting blades and others., Warranty: none, Terms of delivery: EXW Germany

Used vibrating vibrating screen with two sieve inserts for three fractions. The sieve was used for the post-cleaning of plastic granules from cable recycling. The lower deck has an additional perforated plate with anti-clogging cleaning balls. The screen comes with inserts of 0.8 mm, 1.3 mm and 2.3 mm.

Small dosing accumulator with screw conveyor for cable recycling plants, wood chips, etc. Capacity approx. 650 litres or 400 - 500 kg of pre-shredded old cable Adjustable conveying speed with frequency converter/inverter 0 - 16 rpm Drive only 0.55 kW with reduction gear Discharge height approx. 750 mm Dimensions (LxWxH): 2,200 mm x 800 mm x 1,800 mm Mobile via large heavy-duty castors with brakes

Large Four Shaft Shredder with Two Cutting Shafts and Two Feed Shafts. Until now, the shredder has been used as a pre-shredder for the recycling of old cables. Due to the hydraulic tamper, the shredder can also be used for bulky materials. Changing the screens is hydraulically assisted and therefore easy to do. On request, the shredder can also be supplied with the articulated conveyor belt shown here. The conveyor belt is equipped with a magnet in the upper pulley for iron separation.

Single-shaft shredder particularly suitable for secondary shredding, granulation of pre-shredded material. Application: Commercial waste for thermal or recyclable recycling, e.g. paper, cardboard, art and foams, rubber, leather, textiles, floor coverings. etc. Lindner Komet 2800, overhauled machine 02/2024 Year of construction 2015 Control cabinet with FÜ ABB, dustproof with dry cooler Control panel: new Drive motors : ABB 2x160 kW Paint New/RAL: 5003/7001 Rotor bearings/squeegee/shaft seals : new Wear plates: stainless steel R+L New Knife holder: new All knives/screws : new Sealing ring rotor: new Sealing ring wall: new Terminal strip top: new Terminal strip bottom: Refurbished Counter knife carriage: Recycled Scraper comb beam with sheets: new Gaskets, brackets, bolts, locking bolts: used very well preserved Adjustment screws (counter knife, scraper comb): new Slidi ...

Technical data baler: Manufacturer BOA Type 2040.S.5V.71.37 Year of manufacture 2003 Operating hours approx. 35,598 hours, as of March Pressing force main press 71 t Specific pressing pressure 9.1 kg/cm² Operating pressure 280 bar Dimensions of feed chute 1,620 x 1,080 mm Bale dimensions 1,100 x 1,100 mm, length variably adjustable 800 up to 1,600 mm Drive power 37 kW Tying system 5-fold vertical, fully automatic Throughput rates for quality: B12 / B19, 40 ? 60 kg/cm³, up to approx. 9 t/hour, bale weight up to 850 kg/bale, depends on material Hydraulic oil tank capacity 800 l Transport dimensions 10,020 x 2,400 x 3,400 mm (l x w x h) Machine weight press approx. 24 t Noise level

The JMC 407 is the top seller among our alligator claws. It is cost-effective, has sufficient knife length and enough power for most metal recycling tasks. It is suitable for cutting many materials, such as profiles, piping, motors, gearbox housings. The scissors are also often used for cleaning scrap metals or cutting vehicle radiators. The machine is equipped with a control system without electronics and a manually adjustable hold-down device, which also acts as a protective cover. By means of a foot pedal, the scissors can be used in single or continuous operation. The opening width can be adjusted by means of simple clamping screws. The scissors are from our demonstration pool and can be viewed or tested.

Ermafa Type: RA 1200-350 , Agglomerator Control: Siemens S6 Built: 1995 Dimensions and weights Dimensions LxWxH m: 1.5 x 1.5 x 3.36 Machine Weight Kg: 4250 Other Motor-Three-phase cage rotor motor Performance-355 KW Speed-1488 rpm Voltage-380/660 V;50 Hz Degree of protection-IP 55 Type-IM V3 Mode-S 6 Mixed fraction from shredding 700-1100 kg

Ballshaping- and Delaminationmill Molinator for fine delamination! Diverse Types: RW VKR16/3 / 22-37kW and RW VKR 22/3 / 75-110kW Input Composite Material Examples: Regrind from hair-wire, printed circuit boards, electronic circuits, other composited material. Al / Plastic, Cu / Plastic, Cu / Glass fibre, ABS / Plastic fibres, etc. Type choice: depending on the material / depending on layer thickness / depending on test‘s / according to the desired throughput. Description Molinator: In the inner acts very high forces (High acceleration / high relative-speed)! Bigger parts will be delaminated. Composite-material separates at the phase of boundaries. Metals will be ballshaped. Plastics depending on the specifications stays fluffy” or will be grinded. These effects besides the desired delamination, are helpfully for the separation and are exactly coordinated to our sepa ...

3 Shaft shredder with HARDOX spirals (approx. 500x1700mm), complete hydraulic system with Brevini gearboxes, new base frame with new steel construction, new hopper 6 cbm, inlet-opening: approx. 1100x1700mm, in addition: 7 reserve spirals available

Zig Zag Air Sifter Sizes/ wides from 200mm - 1800mm Precondition for the separation are differences in the material like: - Different sizes of particles - Differences of the density - Differences in the surface condition of the particle - Differences in the form of the particle - Grain size 0.1mm – 40mm, (bigger particles are possible with a special design) We are the manufacturers of these plants and we build Zig Zag Sifter Plants in different sizes. In order to make you a definite offer we need to know some points: 1. What material you want to separate? 2. Grain-size of the material? 3. Bulk weight kg/liter of your material. 4. We have technical center at our house, where we can test your material.

To sieve dry material: like flour-, grainy-, and granule-shaped material. Free running sieve case hanging in a massive framework With an automatic sieve ball cleaning. Sieve-layers in a simple way interchangeably. Applicable to sieve all floury-, grainy materials in dry condition. Sizes of Wide 500 – 1500mm / Lengths 1200 – 2400mm Sieve layers 2 to 4 layers, grain

Demo machine from demonstration pool Enormously versatile cable slot machine thanks to individually adjustable, standing cutting knives. Cables are cut as standard by two knives penetrating the insulation on the side. The series was significantly improved in terms of safety in 2014 and now features a short feeder for thin cables and a long feeder for thick cables. The change is made in seconds by means of a rotary mechanism. The simplicity in the construction and the construction with two powerful, synchronously running rollers is left. With coarse gearing, even thicker cables are safely fed into the knives and transported further after the cutting process for removal. Blunt knives can be easily and cost-effectively sharpened with a standard grinding machine.

Small shredder for various tasks such as old cables, plastics wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). Rotor shaft with connectors for connecting a cooling device (e.g. when used for NYM old cables. The machine is 1 year old and little used from our demo machine inventory. The machine is offered with a one-year used machine warranty.

Heavy peeling machine from also for thick cables up to approx. 110 mm diameter. Cable stripping machine for PVC and lightly reinforced cables. Easy adjustment of the knives by handwheel. Cables are cut from both sides at the same time, so that the remittation drops slightly. Knife individually adjustable by spindle for different strength swelling. Double spindle for precise adjustment of the cable thickness. Two separate 1.5 kW motors for a lot of power when pulling through the cables

Lindner Mircromat 2500 HP, 160 kW, with direct drive. Control cabinet with frequency converter. Knife size 43 x 43 x 19.5 mm (carbide). Number of blades 131. Max rotor speed 265 rpm With large filling shaft (5.6 cbm) and filling hood. Internal pusher 7.5 kW. Perforated sieve 30 mm. New machine

make: Ambra output: 75% mehr Zuzug des Mittel : alle Medien : Ölbinder Recyling-Pack The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Compact but powerful machine for processing old cables up to approx. 25 mm in diameter. The nominal output of the system is 120 kg/hour when using a 4.0 mm perforated screen. By using a pre-shredder, the performance can be significantly increased, then stronger cables are also possible. The machine has been checked and modified in our workshop. - new dividing table - new set of knives - new sieves - new seals - Connection for refrigeration unit - Connection for feed and conveyor belt On request, we can supply additional accessories for the machine, such as: - Pre-shredder -Magnetic drum - Dosing accumulator - Refrigeration unit - Dust filter - Screening drum - Bigbag stand with air conveyance for plastic granules

Used overband magnet with new conveyor belt, new geared motor and new bearings. Length, strap 1,200 mm, magnet 700 mm Strap: width 300 mm, 5 studs Drive: 400V, 0.18 kW Aluminum frame with 4 eyebolts for suspension.

Very good machine from our demonstration pool. Few hours of operation or signs of use. The peeling machine is suitable for XLPE cables, underground cables, cables with steel armouring, cables with aluminium and lead armouring, but also for processing PVC and rubber cables. With this machine, two cuts can be made at the same time in one operation, so that the processing can be twice as fast as with other models. Technical data: Working range/cable diameter: 30 mm to 150 mm Pulling speed: max. 12 m/min Motor: 2x 3.0 kW - 400 volts Dimensions (LxWxH): 1.8 x 1.0 x 1.2 m Weight: approx. 660 kg

Used single-shaft shredder for wood, plastics, old cables, etc. Of course, the machine has received new knives and has been checked by us. Accordingly, we give 3 months of used machine warranty. The shredder has the amplified 30 kW drive (normally 15 kW) and is therefore enormously powerful. The rotor stops in the event of overload or blockage and reverses automatically. The hydraulics of the machine are dry, there are no leaks. Currently, a screen with a hole diameter of 14 mm is used, so that it is perfect for old cables. Of course, other screens in the range of 10 mm to 60 mm can also be used. The shredder is immediately available and can be viewed and tested. Further technical data: Rotor length: 630 mm Rotor diameter: 250 mm Feed travel: 600 mm Loading opening: 1,100 x 1,100 mm Drive rotor: 30 kW Drive hydraulics: 1.5 kW Rotor speed approx.: 90 rpm Weight  ...

Lindner Micromat MS 2000 Drive motor : 75 kW ,400 V/50 Hz Control cabinet: complete star/triangle Rotor speed: approx. 80 rpm at 50 Hz. Rotor blade: 104 pcs. New Rotor blade shape: 43x43x19.5 mm Infill opening: LxW 2030 x 1650 mm Rotor length: 2030 mm Rotor flight circle: 560 mm Wiper comb:yes Counter knife: yes Hydraulic power unit: complete Hydraulic cylinder sieve cassette:sieves 50x50 mm Total weight approx. 11 t Dimensions LxWxH mm: approx. 4520 x2970 x 2660 mm Viewing and trial run possible by appointment. Shipping time: immediately

Brand: LINDNER, Model: Jupiter 3200, Type: Single shaft shredder for pre-shredding, Year of construction: 2011, Number of knives: 36 pieces, Knife shape: 145x145x47, Sieve perforation: 148 mm, Rotor speed: 80 rpm, Weight: 39 tonnes, Electric motor: FIG, Power: 2 x 160 kW, Electrics: 3 switch cabinets with 2 working, frequency converters (Schneider),, original PLC control in German, without, cables from motor to switch cabinets., Equipment: Hydraulic unit, funnel; without the conveyor belt seen in the photo, Knives: Present, but used (counter knives were removed during the photo, shoot), Operating hours: 30000 h, Overall condition: very good working condition., Warranty: none, Terms of delivery: EXW Bremen/Germany, Machine is ready for use and can be put into operation quickly at any time., fire: LINDNER, model: Jupiter 3200, Year of construction: 2011, Number of knives: 36 pieces, Knife  ...

Lindner Micromat MS 2000 Drive motor : 75 kW ,400 V/50 Hz Control cabinet: complete star/triangle Rotor speed: approx. 80 rpm at 50 Hz. Rotor blade: 104 pcs. New Rotor blade shape: 43x43x19.5 mm Infill opening: LxW 2030 x 1650 mm Rotor length: 2030 mm Rotor flight circle: 560 mm Wiper comb:yes Counter knife: yes Hydraulic power unit: complete Hydraulic cylinder sieve cassette:sieves 50x50 mm Total weight approx. 9.5 t Dimensions LxWxH mm: approx. 4520 x2970 x 2660 mm Viewing and trial run possible by appointment. incl. funnel Shipping time: immediately

Cable pelletizing machine V-C03 CE and UVV approved, max. 30-50 KG/h, 0.1-30mm diameter of cables, weight 515KG, L 1000 X W 580 X 1,700 mm, 5.18 KW, 1 year warranty, easy to move with heavy-duty castors, available from 12 KW ex location D-57223 Kreuztal. 8.900€ plus 19% VAT

Small but very robust and powerful shredder for a wide range of tasks such as old cables, plastics, wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). Rotor shaft with connections for connecting a cooling unit (e.g. when used for old NYM cables. The machine is and little used from our demo machine inventory. The machine is offered with a one-year used machine warranty.

Machine for processing mixed old cables including fine conductors and stranded cables, Due to the special rotor system and the large flywheel masses, the system is also suitable for operation in manual insertion. The machine is equipped with a cooling unit that optimizes the granulator with a flow temperature of 0.5 °C for the use of heat-sensitive cables, such as NYM etc. The control electronics of the system enable fully automatic operation in a line with pre-shredder, conveyor belt, dosing accumulator, etc. The machine includes several sets of knives and different screens.

Used and refurbished turbine mill from Tecnoecology for the digestion of old cables, especially fine strands or computer cables. Balling takes place at about 3,000 rpm. The tools are rotatable and have 4 usable edges. The turbine mill can be operated stand-alone or integrated into an existing system without a pellet mill. The machine has a 20 kW drive and can process up to approx. 300 kg of material per hour.

A complete baling press system is for sale, consisting of a chain belt conveyor, the baling press with wire stations and bale chute. Technical data baler: Manufacturer BOA Type Impress D130.110.B.5-(5R).1.6 Year of construction 2009 Press power main press 127 tons Specific press capacity 10,7 kg/cm² Working pressure 280 bar Feed channel 1.620 x 972 mm (l x w) Press volume / cycle 4,1 cbm Volume throughput without load up to 865 cbm/hour Cycle time under operating conditions 22 sec. Press stroke 2.900 mm Bale size 1.100 x 1.100 mm (w x h) length adjustable Driving power 2 x 55 kW Connected load 132 kW Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm up to 17 to/h bulk weight of 50 kg/cbm up to 29 to/h bulk weight of 100 kg/cbm up to 37 to/h bulk weight of 150 kg/cbm up to 51 to/h Bale weight up to 1.200 kg Volume hydraulic oil ...

Technical data shredder: Manufacturer Lindner Recyclingtech GmbH Type Micromat 2000 Year of construction 2012 Operating hours 5,842 hours, as of March Drive power 160 kW Filling opening 2,790 x 2,405 mm Filling height 2,594 mm Cutting chamber volume 4.5 m³ Number of sieve sheets 4 pieces Discharge width 2,225 mm Input density 160 up to 200 kg/m³ Input granulate