rapid press used for sale

pressure:20 t Stroke:230 mm table surface area:Ø600 mm distance table - lower edge of ram:770 mm weight:595 kg

HOT PRESS model SIMI 4LP second hand machine plates useful size mm. 2500 x 1300 n.04 pistons diam.mm. 80 max. thrust Ton. 60 specific pressure max. kg.2 / cm2 opening mm. 320 hot water plates heating via wood boiler (optional) weight kgs. 3000

Tot.kW 43 Volt 400V /50Hz

Bale size (W x H) approx. 1,100 x 700 mm Bale weight approx550kg

weight of the machine ca.:620 kg dimensions of the machine ca.:1000 x 920 x 1550 mm

Pressure:175 t chamfer lenght:4100 mm distance between columns:3600 mm column arm:410 mm ram stroke speed:180 mm/sec return speed:135 mm/sec working speed:10 mm/sec work stroke:275 mm oil volume:200 l dayligth:550 mm table height:900 mm table width:90 mm total power requirement:15 kW weight of the machine ca.:12000 kg dimensions of the machine ca.:5100 x 2150 x 2850 mm

Key data: 15 t, 66 mm

Burger Press D07 Length 1.20 m Width 0.60 m Height 1.70 m 2 Hand control Switch to foot control 1 press die

Specifications: Capacity 300 to Stroke rate 35 strokes Plunger width 1000 mm Projection 450 mm Plunger stroke 20 - 140 mm Plunger adjustment 80 mm Engine power 30 hp Weight roughly estimated 18 tons

nominal force:100 t stroke:320 mm no. of strokes:35 /min distance between columns:360 / 250 mm Distance table/ram, max. stroke up, adjustment up:500 mm table surface area:320 x 450 mm table height over floor:660 mm ram surface:250 x 280 mm spindle diameter:125 mm power capacity:3,0 kW weight:4,5 t Dimensions (WxDxH):2,0 x 1,6 x 3,1 m

pressure:60 t distance between columns:650 mm stroke:220 mm distance table/ram, max. stroke up, adjustment up:410 mm table surface area:600 x 525 mm hole in the table:110 mm table height over floor:900 mm side window:200 mm ram surface:560 x 490 mm power requirement:15,0 kW dimensions (WxDxH):1,9 x 1,3 x 2,7 m foundation pit:not necessary

pressure:250 t distance between columns:1110 mm stroke:250 mm Distance table/ram, max. stroke up, adjustment up:500 mm Table surface area:1100 x 900 mm Table height above floor:950 mm Side window:690 mm Ram surface:1100 x 900 mm Oil volume:730 l Power capacity:56,0 kW Dimensions (WxDxH):2,3 x 1,55 x 3,96 m

Used multi-layer paver Zenit 844 Built in 1993 inclusive: 1 piece concrete mixer 750 l Teka 1 piece concrete mixer 500 l approx. 12 pieces of used moulds approx. 100 production pallets Used concrete multilayer machine Manufacturer: Zenith Type: 844 Year: 1993 including: - 1 pcs 750 liter mixer Teka - 1 pcs 500 liter blender - about 12 moulds - about 100 pcs production boards

nominal force:160 t stroke:140 mm no. of strokes:85 /min distance between columns:400 mm distance table/ram, max. stroke up, adjustment up:500 mm table surface area:400 x 450 mm table height over floor:800 mm Allowed max. force:230 t ram surface:400 x 320 mm spindle diameter:125 mm power requirement:7,35 kW weight:5,0 t dimensions (WxDxH):1,7 x 1,2 x 2,9 m

pressure:300 t distance between columns:1800 mm stroke:1000 mm Distance table/ram, max. stroke up, adjustment up:1300 mm Table surface area:1600 x 1200 mm Table height above floor:1080 mm Ram surface:1600 x 1200 mm Weight:24,0 t Dimensions (WxDxH):2,8 x 2,1 x 6,0 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2

no. of strokes:150 /min impact energy:420 kJ distance lower die block / ram gudeway:435 mm Throat:425 mm steel forging - rectangular up to:110 mm steel forging - diameter up to:125 mm power requirement:22,0 kW weight of hammer:3,9 t weight of anvil:3,0 t ram hammer weight:200 kg weight:6,9 t dimensions (WxDxH):1,1 x 2,3 x 2,4 m

Specifications: Capacity 40 tons 2 strokes 57 + 86 H/min Projection 250 mm Plunger stroke 8 - 88 mm Plunger adjustment approx. 63 mm Table , WxD approx. 570 x 450 mm Max. installation height approx. 330 mm

Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw

Power 550 W

SINGLE POINT OPEN BACK INCLINABLE POWER PRESS Inv. No. 11.420PC Make IWK Model PEKRON 150Z Machine No. 1501 Capacity 150 tons Ram stroke 200 mm Ram adjustment 100 mm Shut height min/max 370 / 570 mm Strokes per minute 40 Knock out in ram 0 – 70 mm RPM 10 - 815 Throat 290 mm Power inclinable 30 degrees, 4kW Table 1000 x 630 mm Ram 760 x 410 mm Q 12 Volts 230 / 400 Cycles 50 Hz Including: Bolster plate 1.000 x 630 x 80 mm Bolster plate 1.000 x 630 x 90 mm Table opening, diameter 440 mm Updated electrics 2004 CE certified

Equipped with shrinkage of 6-45 mm; Manual pump; Shrink force 1000Kn; 7 Sets of molds; Completion indicator light; Maximum opening diameter without mold: 50mm; Maximum opening diameter with mold: 40mm; Hydraulic tank capacity: 1L; Hydraulic oil capacity: 0.5L; Unused

Including various tools;

VORONEZH K8544 Hot Forging press YEAR : 1980 / 2008 OVERHAUL AND INSTALLED FORCE : 2500ton RAM STROKE : 350 mm RAM SIZE : 1120X1070 mm TABLE OVERALL SIZE : 1400X1200 mm NUMBER OF STROKES IN CONTINUOUS MODE : 60 NUMBER OF STROKES IN MANUAL MODE : 26 SHUT HEIGHT : 890 mm STROKE OF UPPER KNOCK OUT : 60 mm STOROKE OF LOWER KNOCK OUT : 70 mm MAIN MOTOR : 132KW (CHANGED TO HYUDAI HEAVY Y2012) PRESS OVERALL DIMENSION : 5380X4680X6400 mm HYDRAULIC BOLSTER NEW IN 2007 CONDITION : VERY GOOD WORKING CONDITIONS Trimming press available

Rice spotting press Weight: 5000kg

Consisting of two punching stations, driven by pneumatic cylinders incl. Installed punching tool on pedestal Dimensions of the pedestal: 560 x 300 x 170 mm

Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw

Specifications Maximum pressure: 60 tons Press force: 156 t/m² Bale size: 1100 x 1100 x 700 mm Bale weight: 400 kg Power supply: 400V/ 13kW Year of construction: 2014 Dimensions of the tailgate: 2815 x 1085 x 2250 mm Machine weight: 7.5 t The machine is functional

Equipped with shrinkage of 6-45 mm; Manual pump; Shrink force 1000Kn; 7 Sets of molds; Completion indicator light; Maximum opening diameter without mold: 50mm; Maximum opening diameter with mold: 40mm; Hydraulic tank capacity: 1L; Hydraulic oil capacity: 0.5L; Unused

Unused, crimping range 15-63mm, maximum aperture 75mm, 53.5 mpa, force 500 T, 3000W

with mounted punching tool

Gluing Press / Press Rotor / Gluing Stars For the production of solid wood panels or similar Manufacturer: ACMA Levels: 4 Hydraulic Cylinders: 6 per level Hold-down: 2 frames per level Working area per level approx. 2900 x 1150 mm

SECOND HAND BENDING PRESS - plates dimensions mm. 3100X800 - opening mm. 800 - 8 cyl. diam. 80 mm.

Machine number: 2-0513 Compressive force: 28 kN Stroke: 60 Table dimensions: 200 x 160 mm with pneumatic punching tool mounted

Condition: unchecked Item is sold as is Weight may be ggbfs. Deviate. Machine must be dismantled by the buyer and transported out of the hall area. It cannot be guaranteed that a forklift is on site.

With foot switch, on metal base, self-made.

Table dimensions: approx. 190 x 110 mm incl. installed tools

Serial number: 0069 Compressive force: 28 kN Stroke: 12 mm Delay time: 0.063 sec min./max. operating pressure: 3/6 bar Table dimensions: approx. 200 x 150 mm incl. installed punching tool

Machine number: 2-0586 Compressive force: 28 kN Stroke: 60 Table dimensions: approx. 200 x 150 mm incl. installed punching tool

Specifications Maximum pressure: 65 tons Pressing force: 84 tons/m² Duct cross-section: 1000 x 750 mm Bale weight: do 550 kg Power supply: 400 V/ 45 kW Year of construction: 2011 Number of ties: 4 vertical Dimensions of the tailgate: 1400 x 920 mm Weight: approx. 13 tones Bale tying: automatic

Specifications Maximum pressure: 50 tons Press force: 7.14 kg/cm² Duct cross-section: 1000 x 700 mm Bale weight: do 500 kg Power supply: 400 V/ 30 kW Number of ties: 3 horizontal Dimensions of the tailgate: 1250 x 950 mm Weight: about 10 tons Bale tying: automatic Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the duct. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers Large flaps of the press chamber for easy maintenance

Key data: 200 mm

used press brake Trumpf TruBend V200 + BendMaster 60 Year of construction 2004 Pressing force max: 2000kN Stroke max: 365 mm Operating pressure max:340 bar 1 piece B0401A0009 = BendMaster 60 1 piece B0106A0073 = TRB V200-6A 1 piece of protective housing incl. lighting 1 piece of BendMaster roadway 14 meters in 2 meter segments 1 piece of system control system trump

Length 3120 mm; WILA NS Recording

Equipped with 10 crimp sets; unused

Hydraulic Hose Press; Crimping range: 15-63mm, Max aperture: 75mm, Voltage: 380V, Wattage: 3000W, Pressure: 53.5 Mpa Packing size: 780x540x1350 Weight incl. packaging: 280 kg Unused.

with battery and charger leaking oil