127,520 used machines on RESALE, but how to find them? Machine Search
: 45 to. no. of strokes: 24 Hub/min hole diameter in sheet thickness: max. Ø 27 in 13 mm : 80x80x8 : 60x60x6 mm flat steel: 300x10/200x13 mm : 7 mm engine output: 2.2 kW range L-W-H: 1550x820x1540 mm weight: 760 kg Standard equipment: - Complete knife set for flat steel shears - complete knife set for angle steel shears - complete standard punching equipment - Stamp quick release device for punches up to Ø 27 mm - Rectangular notching device complete with hold-down device - notch - Support table for punching device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
round bar steel: 50 mm square edge steel: 40 x 40 mm L-beam: 140 x 13 mm Punch power: 900 kN hole punching press: throat: 510 mm hole punching press: max. length of stroke: 29 mm hole punching press: capacity (dia. x thick.): 31 x 20 mm notching: l + T material: 80 x 14 mm no. of strokes: 40 / 45 Hub/min total power requirement: 4 kW weight of the machine ca.: 3,7 t dimensions: 2,1 x 0,7 x 2,12 m Accessories: various punches and dies The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 200 mm, 400 , 360
Profile Bending machine Model AR360 -Year 2004 MG brand made in Italy OUTPUT SHAFTS 360 MM Capacity as per the original bending chart here enclosed Configuration installed with the machine -Pyramid dual pinch side rolls independent hydraulic positioning bending and pre-bending performance -The 3 shafts driven with hydraulic motor and gear unit individual on each roll -Synchronized speed automatic hydraulic control between the 3 rotating shafts -hydraulic traction tool to roll HEB_INP_UPN bending on hard-side. -Lateral correctors left/right hydraulic operated in 3 directions Tooling with the machine -Set of rollers for pipe: 6” and 12” -Set of rollers with adjustable opening width up to 400 mm ( for all the profiles bending easy way and hard way ) -Set of rings to increase the rollers opening width up to 500 mm ( for all the symmetric profiles b ...
Key data: 200 mm, 300 , 200
Profile bending roll used equipment hydraulic model AR200 year 2008 make MG Italy Capacity bending chart photo in enclosed -Technical data: Output shafts size 200 mm -Machine complete with set of rollers adjustable for the various shape of profiles. -Traction tool hydraulic operated for the HEB-beam - IPE - UNP bending the hard side. -Lateral correctors left and right side hydraulic operated in 3 direction. -Included additional set of rolls for pipe 6" inches -Machine with 3 rolls driven system with individual hydraulic motor and axial gear-unit on each shaft. -The 3 shafts working on bearings, heavy duty type with sealed lubrication. -Centralized control panel movable on wheels with all electric commands. -Dual rolling speed up to 5 mtr/min with automatic balancing system between the 3 rolls. -Safety devices in compliance with European regulation. CE mark. - ...
AMOB MAH 40/3 CNC 3-roll bending machine was built in 2021 in Portugal by AMOB Group. The machine, designed for bending tubes and profiles, ensures the highest precision and repeatability of the produced parts. The machining process is performed by three hardened rollers, of which the upper roller has hydraulic adjustment. Each of these is driven by a reliable, high-power motor, which is located inside a fully welded body. This solution enables bending of even the most complex shapes both vertically and horizontally. All this is complemented by an advanced CNC control with memory for numerous programmes. The MAH 40/3 CNC tube and profile bending machine weighs 540 kg. Technical specifications of the AMOB MAH 40/3 CNC bending machine - control panel with CNC control - number of rollers: 3 - roller diameter: 148 mm - roller rotational speed: 12 rpm - number of shafts: 2 - shaft di ...
: 50 (500) mm : 45 (500) mm L-beam: 80 x 80 x 8 (800) mm T - beam - web outwards: 80 x 9 (800) mm Axis diameter: 60 mm work speed: 5,0 m/min Tool diameter: 195 mm total power requirement: 3 kW weight of the machine ca.: 1,0 t dimensions of the machine ca.: 1,2 x 0,9 x 1,2 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display - hardened special steel shafts - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable - Horizontal and vertical operation - Engine with braking device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
angle steel/side length: unbkt mm double T-iron on the x-axis: unbkt. mm U-iron on the x-axis: unbkt. mm total power requirement: 37 kW weight of the machine ca.: 16 t dimensions of the machine ca.: 2900x2300x2150 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
angle steel/side length: siehe TD mm double T-iron on the x-axis: siehe TD mm U-iron on the x-axis: siehe TD mm total power requirement: 15 kW weight of the machine ca.: 4,6 t dimensions of the machine ca.: 1850 x 1550 x 1685mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
angle steel/side length: siehe TD mm double T-iron on the x-axis: siehe TD mm U-iron on the x-axis: siehe TD mm total power requirement: kW weight of the machine ca.: 0,9 t dimensions of the machine ca.: 1160 x 1000 x 1175mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
angle steel/side length: unbkt mm double T-iron on the x-axis: unbkt mm U-iron on the x-axis: unbkt. mm total power requirement: 77 kW weight of the machine ca.: 45 t dimensions of the machine ca.: 6000x5000x3500 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
ELUMATEC SBZ 628 profile machining center was built in 2016 in Germany by elumatec AG. The machine has been regularly serviced throughout its service life. The ELUMATEC SBZ 628 profile machining centre is an extremely versatile solution for advanced machining of window profiles, door profiles or facades. It enables precision machining of any type of profile with a maximum length of 7500 mm. Cutting, drilling and milling is performed in a single work cycle by advanced machining units located inside a sound-absorbing cabin. A clamping system positions the workpiece instantly and holds it securely during the entire machining process. Grippers, spindles and a cutting disc with a 360° rotation range enable machining of the profile in multiple positions, while maintaining constant accuracy. All this is completed by the quick-change mechanism for guide rollers and tools, which considerably ...
Qty. 1 Second-hand Electrostatic Multi Colour Powder Coating Production Line Mfc.: Gema Type: OptiFlex A2-14 Guns Built: 2013 OptiFlex A2 adjusts the air settings electronically by means of patented DVC System and monitors the production parameters continuously, resulting in a high quality coating Result. Work piece data – Aluminium Profiles Dimensions: 1800 x 400 x 6000 mm – H x W x L Conveyor speed: 2.0 m/min. One new Booth No. 2 (Mobile on rails) Magic Plus Booth” with cyclone recovery installed 2013, consisting of: Gema Electrostatic Powder Coating Equipment type OptiFlex A2 – 14 Guns With OptiFlex AS05 and OptiStar CG06 Gema Reciprocator System type ZA05-23 with carriage type XT10 for remote width positioning and outside cleaning Gema Control System type CM-30 Magic control including height recognition system Gema Quick Color change system Magic Plus with mu ...
angle steel/side length: unbkt mm double T-iron on the x-axis: unbkt mm U-iron on the x-axis: unbkt. mm total power requirement: 90 kW weight of the machine ca.: 55 t dimensions of the machine ca.: 6500x5300x3750 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
angle steel/side length: unbkt, mm double T-iron on the x-axis: unbkt. mm U-iron on the x-axis: unbkt. mm total power requirement: 11 kW weight of the machine ca.: 3,36 t dimensions of the machine ca.: 1175x1340x1650 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
angle steel/side length: unbkt. mm double T-iron on the x-axis: unbkt. mm U-iron on the x-axis: unbkt. mm total power requirement: 55+15 kW weight of the machine ca.: 24 t dimensions of the machine ca.: 3850x3050x82800 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
angle steel/side length: siehe TD mm double T-iron on the x-axis: siehe TD mm U-iron on the x-axis: siehe TD mm total power requirement: 7,5 kW weight of the machine ca.: 2,35 t dimensions of the machine ca.: 1580 x 1200 x 1410 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
angle steel/side length: siehe TD mm double T-iron on the x-axis: siehe TD mm U-iron on the x-axis: siehe TD mm total power requirement: 120 kW weight of the machine ca.: 78 t dimensions of the machine ca.: 6100 x 5150 x 4300mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
SAHINLER HPK 65 3-roll bending machine was built in 2005 in Turkey by Şahinler Metal Makina Endüstri A.Ş. The machine, designed for precision machining of tubes and profiles, is an excellent choice for any industrial plant. It enables workpieces to be made in circular, arc or spiral shapes with a fixed radius. The machining process is performed by three hardened rollers, of which the two lower rollers have hydraulic adjustment. These rollers are driven by a reliable, high-powered motor located inside a fully welded housing. Depending on production requirements, the SAHINLER tube and profile bending machine can operate in both vertical and horizontal positions. The total weight of the machine is approximately 1000 kg. Technical specifications of the SAHINLER HPK 65 bending machine - number of rollers: 3 - roller diameter: 180 mm - shaft diameter: 60 mm - working speed: 5 m/min ...
angle steel/side length: unbkt. mm double T-iron on the x-axis: unbkt. mm U-iron on the x-axis: unbkt. mm total power requirement: 30 kW weight of the machine ca.: 8,6 t dimensions of the machine ca.: 2500x2000x1900 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
round bar steel: 45 mm square edge steel: 42 mm L-beam: 140 x 13 mm flat steel: 350 x 20 mm pressure: 550 kN throat: 305 mm notching: rectangle tool: mm total power requirement: 5,5 kW weight of the machine ca.: 1260 kg dimensions of the machine ca.: 1360 x 750 x 1565 mm 2 working cylinder with 2 separated electric foot switch for 2-people-handling New notching table, new knife for the rectangle notcher and new punching table included For further information please see brochure. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
amplification -fold: ? diameter: 380 mm workpiece height max.: 200 mm voltage: 230 V weight of the machine ca.: 245 kg dimensions of the machine ca.: 0,80 x 1,20 x 2,00 m - Serial-No.: 1740 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
FOM INDUSTRIE profile machining center was built in 2009 by F.O.M. INDUSTRIE s.r.l. This machine, designed for precision machining of PVC profiles, is an excellent choice for businesses specialising in the manufacture of windows. It enables, among others, milling, cutting or making ventilation and holes for the handle. Window profiles are machined by means of various types of aggregates. The standard machine in this series has 14 aggregates, however, the machine in our offer has been equipped with additional milling and drilling aggregates and has a total of 18 of them. This solution significantly increases the machining capacity of the machine as well as the overall machining efficiency. The FOM INDUSTRIE PVC profile machining center is also extremely easy to operate. All machining parameters are programmed in the intuitive CNC control with graphic software. Technical specifications ...
5 axis sawing, drilling and milling – portal machining center with 9 meters machining length (alternatively shorter – 7 or 4 meters machining length) for all profile and pipe materials - aluminum - steel - stainless steel - plastics - fiber composite plastics such as GRP and CFRP - drilling + tapping, flow drilling, milling + thread milling at a free angle – for example, steel profiles sawing up to 15 mm wall thickness – glass or carbon fiber materials up to 25 mm wall thickness Largest saw blade diameter 500 mm Largest machining length with a 5-sided machining 9,000 mm Largest workpiece cross-section 650 mm x H 450 mm Working range in five-axis operation 9,000 mm x 475 mm x H 450 mm Spindle drive power 18 kW at 60% ED – 15 kW at 100% ED Milling spindle speeds up to 24,000 rpm Moving turret tool magazine for 12 pieces of tools Tool holder HSK63 Rapid speeds up to 100 ...
Finishing unit, modular unit, format processing unit, double-end tenoner, edge processing machine, scraper for edge processing machine -Manufacturer: Homag, profile scraper from edge banding machine BRANDT KM 36 / KM35 -Quantity: 1 piece available -Dimensions: 510/430/H570 mm -Weight: 62 kg
Qty. 1 Second-hand vertical powder painting line for Aluminium profiles Mfc.: Trevisan Cometal Built: 2007 Type: IV/7.00 Profile dimensions: 7000 x 150 x 200 mm - H x W x D Weight of profiles: 25 kg/each max. Total weight onto the chain: 10,000 kg Weight distributed linearly for only 1 meter: 50 kg/m of chain Conveyor speed: 1.5 m/min. Temp. in the polymerisation furnace: 170÷195 °C Rated hanging pitch along the chain: 66/100/133/200 mm Scope of supply: Pre-treatment tunnel Drying oven Painting system Cleaning system Infrared oven Polymerisation oven Descending chain conveyor Transport system
I sell a 4-side brush machine suitable for windows, turrets, tables, etc. Futura MS120 Y1 X2, built in 2005 Working width 1200mm Working height 200mm Total weight 2500kg Configuration: Side grinding heads left - right H.170mm 2 underheads left - right nylon B.140mm Oscillating top head B.260mm Large grinding heads top - bottom B.1150mm Machine together with all the heads on the picture. Available the same.
Rubber sealing profile, sealing plate, curing tool, seal, edge protection, solid rubber rectangular profile -Rubber sealing profile: with 2 grooves, 3 pieces -Length: 3 x 8450 mm / total 25.35 m -Cross-section: 50 x 55 mm -Groove width: 5 mm -Weight: 120 kg
Control cabinet, distribution cabinet, control cabinet TS modular cabinet, profile door -Profile door KTS for: refrigerator -TS8 1200 x 2200 -Price: per piece -Number: 2 pieces -Dimensions: 2240/680/H280 mm -Weight: 66 kg
Ring bending machine, profile bending machine, three-roll bending machine, bending machine -Outer diameter: 200 mm -for: 35 mm pipe -Bearing seat: Ø 55 mm -Bore: Ø 49 mm -Quantity: 2 rolls available Price: complete -Dimensions: Ø 200 x 81 mm -Weight: 11 kg
round bar steel: 25 mm square edge steel: 22 mm L-beam: 70 x 7 mm cutting capacity: 100 x 10 mm plate thickness: 10 mm total power requirement: 1,3 kW weight of the machine ca.: 0,6 t dimensions of the machine ca.: 1,1 x 0,65 x 1,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 30 / 900 mm : 30 / 900 mm L-beam: 35X35X5 / 600 mm T - beam - web outwards: 50x6 / 600 mm Axis diameter: 40 mm work speed: 4,5 m/min roll diameter: 148 mm total power requirement: 1,1 kW weight of the machine ca.: 0,3 t dimensions of the machine ca.: 0,75 x 0,6 x 1,4 m Electric profile roller - Either horizontal or vertical working - 1 set of hardened standard rollers - lower 2 rollers are driven - 1 set of plastic rollers for diameter 33.7mm / 1 - Operation manual - Foot switch left / right and EMERGENCY STOP The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Profile steel shear, profile shear, punch, punching machine, hole punch -Pressure force: 40 tons -Punching -scissors -cut -disengage -mechanical release -Foot switch: 1 -various stamps and dies -Dimensions: 800/1250/H1800 mm -Weight: 1112 kg
Hinge, door hinge, folding hinge, angle profile -Angle profile: Material: Aluminum, 45 pieces -Dimensions/recess: see photos / technical drawing -Price/Fee: complete Dimensions: 70/60/H35 mm -Weight: 0.05 kg/pc.
round material: 30 x 1 mm square material: 30 x 30 x 1 mm : 16 mm : 30 x 10 mm speeds: 9 U/min total power requirement: 1,1 kW weight of the machine ca.: 0,32 t dimensions of the machine ca.: 0,82 x 0,60 x 1,26 m Electric roller profile with - 5 set of rollers 2x 20mm and 30mm for round material, 1x for flat material 1x for square material 1x for? - footswitch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I sell a tenon machine for parallel milling, grooves for pallet tape etc. WACO T2-SL Year of construction 1984. Groove width 30mm. Motor 3,3kW Made in Germany. Available the same. With dokumentazion.
MEPAL ATLANTIS C3SR profile machining center was built in 2018 in Italy by MEPAL Italia s.r.l (RobTech). The machine is new, stocked after purchase and has never been in operation. MEPAL ATLANTIS C3SR is an advanced CNC machining center designed for precision machining of aluminium and PVC profiles from three sides. It is designed to perform such operations, i.e. drilling and milling of workpieces with a maximum wall thickness of 2.5 mm and lengths in excess of 3 metres. All these processes are performed fully automatically in three numerically controlled axes (X,Y,Z). Inside the large work area there is a rotary work table, which is pneumatically rotatable within the range of -90°, 0° and +90°. This solution allows workpieces to be machined from different sides without having to refit the workpiece. The spindle, driven by a powerful 4.5 kW motor, reaches a speed of as much as 1800 ...
Pressing tool, clamping pad, square profile, support profile, alignment pad -Square profile: clamping base, support profile, alignment base -Length: 503 mm -Number: 2x profile available -Price: per piece -Dimensions: 503/97/80 mm -Weight: 27.5 kg/pc.
Technical data of the CS Sigma profile: Manufacturer: SSI Schäfer Type designation: CS 300-3,0 Included in delivery: 01x CS Sigma Profile, II Choice Material color: sendzimir galvanized Total length: approx. 2,550 mm CS-Sigma profile: approx. 300x75x15 mm Material thickness: approx. 3.00 mm
Pressing tool, clamping pad, square profile, support profile, alignment pad -Square profile: clamping base, support profile, alignment base -Length: 515 mm -Number: 3x profile available -Price: per piece -Dimensions: 515/97/80 mm -Weight: 28.3 kg/pc.
Pressing tool, clamping pad, square profile, support profile, alignment pad -Square profile: clamping base, support profile, alignment base -Length: 492 mm -Number: 7x profile available -Price: per piece -Dimensions: 492/97/80 mm -Weight: 27 kg/pc.
Technical data of the CS Sigma profile: Manufacturer: Stow Type: MSNSBG 350/2.0 S 350 GD Included in delivery: 01x CS Sigma profile, used Material colour: sendz. galvanized Total length: approx. 4,450 mm CS-Sigma profile: approx. 350 x 85 x 25 x 12 mm Material thickness: approx. 2.00 mm
Scissors for reinforcing steel or bars max 32mm
Serial number: 60884 Voltage: 50/60 V Auction-ID: A7-48624-49
Includes various interchangeable rollers Auction-ID: A1-48414-135
maximum number of results exceeded
please refine your search
300 € 
