profile grinder used for sale

grinding range: 1000 mm Dimensions (L/W/H): 1500x700x1600 mm Weight: 900 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Auction-ID: A3-46142-6002

HBM Drill Sharpener, Drill Grinder From 3 to 13 mm In just three simple steps, you can ensure that blunt, worn drills are extremely sharp again. The grindstone at the drill grinder consists of diamond and is therefore extremely hard. That way you always achieve the desired results quickly. You can be sure of a good result, especially with HSS drills. In this way, this device is perfect for use in industrial workshops. Furthermore, the sharpener is suitable for use on just about any type of drill. So it is a flexible tool. Auction-ID: A1-40900-78

ES4019, M75, 1999, 20 - 80 kg/h,

TOTAL LENGTH: 53798 MM, WIDTH: 10500 MM, HEIGHT: 10830 MM; CASSETTE INNER DIM.: 7500x1000x265 MM - L x W x H MAX. PROFILE LENGTH: 7500 MM, NO. OF CASSETTE PLACES: 294, DRVING SPEED: 100 M/MIN. LIFTING SPEED: 60 M/MIN.,

Included in delivery: 01x CS Sigma profile, used Material color: sendzimir galvanized Profile length: approx. 1,950 mm CS-Sigma.: approx. 200 x 65 x 18 mm Material thickness: approx. 1.50 mm Note: The angles shown are not part of the offer. General information about the article: This item is offered for pickup only. A desired transport beyond that or a dispatch of this article is associated with additional costs, which separately depending on the place of delivery or scope of delivery can be queried from us. Our services at a glance: (Prices on request) Assembly, assembly our general assembly conditions must be observed Shelf inspection Shelf inspection according to DIN EN 15635 carried out according to the Requirements of BGR 234 Visual inspection for all shelving systems Delivery with our own fleet (without discharge)

Technical Data: Length: 620 mm Height: 500 mm Width: 380 mm

Specifications: Length: 490 mm Height: 800 mm Width: 400 mm

Technical data: with T-slots Length: 1215 mm Height: 1600 mm Depth: 1000 mm

Technical data: with T-slots Length: 1215 mm Height: 1600 mm Depth: 1000 mm

Included in delivery: 01x CS Sigma profile, used Material color: sendzimir galvanized Profile length: approx. 1,650 mm CS-Sigma.: ca, 200 x 65 x 18 mm Material thickness: approx. 1.50 mm Note: The angles shown are not part of the offer. General information about the article: This item is offered for pickup only. A desired transport beyond that or a dispatch of this article is associated with additional costs, which separately depending on the place of delivery or scope of delivery can be queried from us. Our services at a glance: (Prices on request) Assembly, assembly our general assembly conditions must be observed Shelf inspection Shelf inspection according to DIN EN 15635 carried out according to the Requirements of BGR 234 Visual inspection for all shelving systems Delivery with our own fleet (without discharge)

Aluminium profile, connection profile, Einschiebeprofil 96 x 15 x 1000 mm New condition Price per piece: 6,00 348 STK. in stock

The scope of delivery includes: 01x U-profile, used Material colour: grey Total length: approx. 6,000 mm U-profile dimensions: approx. 50 x 38 mm Material thickness bridge: approx. 5.00 mm Weight / running meter.: approx. 5,49 kg Weight / pcs.: approx. 32,94 kg Note: - In the U-profiles there are 8 - 10 boreholes with a borehole diameter of 11 - 15 mm! - The U-profiles may be slightly bent, as well as small rust or other damage. General information about the item: This item is offered for pickup only. A transport that is also desired or a shipment of this article is associated with additional costs, which separately depending on the place of delivery or scope of delivery.

Hand lever plate and profile steel shears heavy and stable outing cuts sheets, round steel (approx. 15mm), flat steel and T-profiles Mounted on base Special price

Max punching force: 1100 kN Extension: 510 mm Large support table with material flaps on the punchside Electric contact load stop for heare hydraulic holder for profile and flat steel shears with a wide range of tools ; Very good

Maximum punching force: 1100 kN Maximum shear force: 1700 kN punch ing: 510 mm support table hole 31 in 25 mm flat steel: 500 x 22 mm hydraulic holder for the flat steel knife kago n weight: approx. 5000 kg ; Very good

EDGE SANDING machine for PANEL and PROFILES type FMB 2 I composition : 1° belt : tilting variable speed sander (with Inverter) - motor power Hp 2 2° belt : tilting variable speed sander (with Inverter) - motor power Hp 2 Blowers for belt cleaning Carpet speed variator from 5 to 25 mt / min Upper adjustable presser with rubber wheels Lateral support for wide panels volt. 380/50

43.5m aluminium profile at a sensational price €17/m excl., Nut 8mm, 40 x 80mm , used Special price! The current new price of a similar product would be € 38/m = total € 1,650. Take advantage of our one-off package price for 43.5m. If you have a VAT number, we will gladly issue an invoice without VAT. Used - Top condition The part was bought from a company in the course of a machine dismantling and is in very good condition. Scope of delivery: 3 x 221cm, 3 x 217cm, 9 x 200cm, 1 x 192cm, 2 x 184cm, 1 x 138cm, 1 x 129cm, 1 x 109cm, 1 x 105cm, 2 x 98cm, Attention: We also have a package of aluminium profiles 80 x 80mm and 40 x 40 mm. No warranty For these goods we have to exclude warranty claims of the buyer for improvement, exchange, subsequent delivery or also for updating in case of digital components. Also excluded is the liability for direct and indirect cons ...

PETEWE optical tool and profile grinding machine PF 3S Projection area: 440320 mm max. grinding stroke: 15-105 mm Stroke number infinitely variable: 0 - 150 rpm. max. grinding wheels through: 175 mm Spindle speed infinitely variable: 5,000 rpm Swivel range grinding head in the horizontal X plane: x 15° side Y plane: . . . . . . . . . . . . . . vertical Z plane: -2° to +10° Grinding head slide movement in X direction: 120 mm in Y direction: 90 mm Adjustment of werkstuecktraeger in X direction: 160 mm in Y direction: 160 mm Sine-mounted clamping plate Clamping: 150 mm 230 mm Sine setting: 0-30°

- Structure in stainless steel - Workpiece fixing system - Table adjustable - 2 milling spindles - 2 multifunction drilling spindles - Switch box

Bearing number: 3488 Profile steel shears Manufacturer: Mubea, Type: KBLH 500 Machines NR.: 0156085927332, Year of construction: 0 Specifications: Size Printl 50 To Max punching dia 30 x 15 mm mm Stroke length 0-60 mm Number of strokes per min. 16 Extension 410 mm Flat steel 180 x 20 - 400 x 10 mm Angular steel 50 mm Round steel 55 mm Total power 7.5 kW Hydraulic. Length: 1400 mm, Height: 1800 mm, Width: 800 mm, Weight: 1800 kg

KÄRCHER ROBO 30 pipe boring machine for pipes, flat material and profiles With this machine, tubes, flat material or profiles can be cut very quickly and accurately in a single pass. can be drilled or milled at an angle or at an angle up to  50° in such a way that filling rods or filling tubes up to 1" can be drilled or milled can be plugged through. With the standard additional clamp for the jaw chuck, you can not only cut pipes, but also transport flat material or other profiles with the feed and at the desired angle up to over Make 50° single-sided holes or through holes. The clamping jaws in the self-centering vice have a recess at the top for flat material. We are unrivalled when it comes to converting to another material! The feed is positioned at 0.1 mm with the counter with absolute or chain gauge. With the ROBO 30, you don't need to set limit switches or cams for ...

2,000 m construction profiles, U-shape Used goods, good condition, see pictures Galvanized Length per piece approx. 467 cm Profile 7.5/8 cm Material thickness approx. 3 mm Weight per piece approx. 43 kg Negotiation price: € 4,90 net/m ex stock Available individually or as a package A package consists of 20 pieces – approx. 93.4 running meters Goods are in stock. Transportation available on request. Viewing possible at any time by appointment. More information on request. More than 5000 linear metres of pallet racks from numerous manufacturers are constantly in stock. (Changes and errors in the technical data, specifications and prices as well as prior sale reserved! See our terms and conditions, all prices excl. VAT from stock.)

Extruding system with cross-spray head for sheathing of small profiles/filaments consisting of: 30 mm extruder with tool, water bath, extractor and winder Optional with memory for role change

According to description pdf attached complete line for profiles + WPC profiles

angle steel/side length: siehe TD mm double T-iron on the x-axis: siehe TD mm U-iron on the x-axis: siehe TD mm total power requirement: kW weight of the machine ca.: 0,2 t dimensions of the machine ca.: 800 x 700 x 1200mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

angle steel/side length: siehe TD mm double T-iron on the x-axis: siehe TD mm U-iron on the x-axis: siehe TD mm total power requirement: 1,5 kW weight of the machine ca.: 0,385 t dimensions of the machine ca.: 930 x 730, x 1400mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

angle steel/side length: siehe TD mm double T-iron on the x-axis: siehe TD mm U-iron on the x-axis: siehe TD mm total power requirement: kW weight of the machine ca.: 0,6 t dimensions of the machine ca.: 1000 x 700 x 1380mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

angle steel/side length: 40 x 40 x 5 mm U-iron on the x-axis: 80 x 45 x 5 mm roll diameter - bore: 40 mm roll diameter -toolpieces: 150 mm turning speeds: 10 U/min voltage: 400 V / 50 Hz total power requirement: 1,5 kW weight of the machine ca.: 0,3 t dimensions of the machine ca.: 0,8 x 0,92 x 1,4 m • Machine has a standard set of rolls for profile: flat (upright) 60 x 10, flat 80 x 15, Square 35, square pipe 45 x 45 x 2, rectangular pipe 60 x 30 x 3, Further sets of rolls can be supplied optionally, The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

angle steel/side length: 50 x 50 x 5 mm round steel bars: 30 mm U-iron on the x-axis: 60 x 40 x 6 mm roll diameter - bore: 40 mm roll diameter -toolpieces: 118 - 148 mm turning speeds: 9,3 U/min voltage: 400 V / 50 Hz total power requirement: 1,5 kW weight of the machine ca.: 0,425 t dimensions of the machine ca.: 1,5 x 0,8 x 0,8 m • Machine has got a standard roller set for profiles: flat upright 50 x 10, flat 50 x 15, upright 30, square tube 50 x 50 x 2,5, retangular tube 50 x 25 x 2,5. further roller sets optionally: for exampel: 1 set (6 rolls) for round pipe D = 3/8 + D = 3/4, Surcharge for each extra roller set: € 440,-/set Machine in unused condition. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

round bar steel: 50 mm square edge steel: 40 x 40 mm L-beam: 140 x 13 mm Punch power: 900 kN hole punching press: throat: 510 mm hole punching press: max. length of stroke: 29 mm hole punching press: capacity (dia. x thick.): 31 x 20 mm notching: l + T material: 80 x 14 mm no. of strokes: 40 / 45 Hub/min total power requirement: 4 kW weight of the machine ca.: 3,7 t dimensions: 2,1 x 0,7 x 2,12 m Accessories: various punches and dies The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Qty. 1 Second-hand full automatic mat and shine anodising coating line Mfc.: CISART Built: 2013 Stopped: Capacity: 1,800,000 pieces of profiles per annum Maximum Part Length: 3 m Requested area: approx. 630 m² Operators: 4 - 6 Estimated Full Power Consumption: 960 kW +/- 10% Voltage: 415 V, 50 Hz, 3 ph. Heat Consumption Max.: 500,000 Kcal/H +/- 10 % Water Consumption: 3 m³/h Water Consumption (TAP) by Customer: 10 m³/h Air Consumption: 1 m³/h Heating System: Electricity & Gas Acid Recovery System: 3 kg/h CHILLER 400,000 + 160,000 kCal/hr 40 °C Max. Ext. Temp. Water cooling range: 9-14 °C 190 + 80 kW Dozing System Quantity: 8 Eye & Body Wash Quantity: 2 Qty. 49 Tanks, 3.5 x 1.1 x 3.0 m – L x W x H Weight: 10 ton each Tank made of 2,5 mm thick AISI304 sheets

: 50 (500) mm : 45 (500) mm L-beam: 80 x 80 x 8 (800) mm T - beam - web outwards: 80 x 9 (800) mm Axis diameter: 60 mm work speed: 5,0 m/min Tool diameter: 195 mm total power requirement: 3 kW weight of the machine ca.: 1,0 t dimensions of the machine ca.: 1,2 x 0,9 x 1,2 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display - hardened special steel shafts - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable - Horizontal and vertical operation - Engine with braking device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specifications: 2 castors hydraulically adjustable 3 rollers driven Resistance torque: 80 cm³ Shaft diameter: 100 mm Roll diameter: 315 mm lateral hydr. Controlled arm correctors left and right CE. Mark Bending capacity square: 120 x 60 x 5 mm Bending capacity flat steel: 130 x 25 mm Bending capacity tube: 114.3 x 6 mm Bending power angle: 100 x 10 mm Round steel: 80 mm Motor power: 11 kW Control panel with digital display Dimensions (length x width x height): approx. 1750 x 1850 x 1650 mm Weight: approx. 3.6 tons Accessories: Various bending rollers Condition: we will still carry out a complete service on the machine The seller is not liable for typographical or data transmission errors. The machine is appropriate for its age in terms of appearance, technology and wear; used machines are sold without any warranty.

angle steel/side length: unbkt mm double T-iron on the x-axis: unbkt. mm U-iron on the x-axis: unbkt. mm total power requirement: 37 kW weight of the machine ca.: 16 t dimensions of the machine ca.: 2900x2300x2150 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

angle steel/side length: siehe TD mm double T-iron on the x-axis: siehe TD mm U-iron on the x-axis: siehe TD mm total power requirement: 15 kW weight of the machine ca.: 4,6 t dimensions of the machine ca.: 1850 x 1550 x 1685mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

InfoTEC 6205 PRO 5 AXIS profile machining center was built in 2019 in Poland by 4CNC Sp. z o.o. The machine, designed for precision milling, drilling and cutting of workpieces made from a wide range of materials, is an excellent choice for companies with a diverse production profile. Workpieces are machined using a moveable machining station, which moves over an extended work area. This solution significantly increases production efficiency, thanks to the possibility of machining more than one workpiece at the same time. The InfoTEC PRO-X 5 AXIS aluminium profile machining center is offered with a wide range of equipment, including e.g. an advanced CNC controller, programs that facilitate daily machine operation and PANASONIC light curtains. The total weight of the machine is approximately 5800 kg. Technical specifications of the InfoTEC 6205 PRO 5 AXIS beam drill line - number of ax ...

Key data: 200 mm, 400 , 360

Profile Bending machine Model AR360 -Year 2004 MG brand made in Italy OUTPUT SHAFTS 360 MM Capacity as per the original bending chart here enclosed Configuration installed with the machine -Pyramid dual pinch side rolls independent hydraulic positioning bending and pre-bending performance -The 3 shafts driven with hydraulic motor and gear unit individual on each roll -Synchronized speed automatic hydraulic control between the 3 rotating shafts -hydraulic traction tool to roll HEB_INP_UPN bending on hard-side. -Lateral correctors left/right hydraulic operated in 3 directions Tooling with the machine -Set of rollers for pipe: 6” and 12” -Set of rollers with adjustable opening width up to 400 mm ( for all the profiles bending easy way and hard way ) -Set of rings to increase the rollers opening width up to 500 mm ( for all the symmetric profiles b ...

Key data: 200 mm, 300 , 200

Profile bending roll used equipment hydraulic model AR200 year 2008 make MG Italy Capacity bending chart photo in enclosed -Technical data: Output shafts size 200 mm -Machine complete with set of rollers adjustable for the various shape of profiles. -Traction tool hydraulic operated for the HEB-beam - IPE - UNP bending the hard side. -Lateral correctors left and right side hydraulic operated in 3 direction. -Included additional set of rolls for pipe 6" inches -Machine with 3 rolls driven system with individual hydraulic motor and axial gear-unit on each shaft. -The 3 shafts working on bearings, heavy duty type with sealed lubrication. -Centralized control panel movable on wheels with all electric commands. -Dual rolling speed up to 5 mtr/min with automatic balancing system between the 3 rolls. -Safety devices in compliance with European regulation. CE mark. - ...

angle steel/side length: siehe TD mm double T-iron on the x-axis: siehe TD mm U-iron on the x-axis: siehe TD mm total power requirement: kW weight of the machine ca.: 0,9 t dimensions of the machine ca.: 1160 x 1000 x 1175mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

angle steel/side length: unbkt mm double T-iron on the x-axis: unbkt mm U-iron on the x-axis: unbkt. mm total power requirement: 77 kW weight of the machine ca.: 45 t dimensions of the machine ca.: 6000x5000x3500 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

angle steel/side length: unbkt mm double T-iron on the x-axis: unbkt mm U-iron on the x-axis: unbkt. mm total power requirement: 90 kW weight of the machine ca.: 55 t dimensions of the machine ca.: 6500x5300x3750 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

angle steel/side length: unbkt, mm double T-iron on the x-axis: unbkt. mm U-iron on the x-axis: unbkt. mm total power requirement: 11 kW weight of the machine ca.: 3,36 t dimensions of the machine ca.: 1175x1340x1650 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

angle steel/side length: unbkt. mm double T-iron on the x-axis: unbkt. mm U-iron on the x-axis: unbkt. mm total power requirement: 55+15 kW weight of the machine ca.: 24 t dimensions of the machine ca.: 3850x3050x82800 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

AMOB MAH 40/3 CNC 3-roll bending machine was built in 2021 in Portugal by AMOB Group. The machine, designed for bending tubes and profiles, ensures the highest precision and repeatability of the produced parts. The machining process is performed by three hardened rollers, of which the upper roller has hydraulic adjustment. Each of these is driven by a reliable, high-power motor, which is located inside a fully welded body. This solution enables bending of even the most complex shapes both vertically and horizontally. All this is complemented by an advanced CNC control with memory for numerous programmes. The MAH 40/3 CNC tube and profile bending machine weighs 540 kg. Technical specifications of the AMOB MAH 40/3 CNC bending machine - control panel with CNC control - number of rollers: 3 - roller diameter: 148 mm - roller rotational speed: 12 rpm - number of shafts: 2 - shaft di ...

angle steel/side length: siehe TD mm double T-iron on the x-axis: siehe TD mm U-iron on the x-axis: siehe TD mm total power requirement: 7,5 kW weight of the machine ca.: 2,35 t dimensions of the machine ca.: 1580 x 1200 x 1410 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

angle steel/side length: siehe TD mm double T-iron on the x-axis: siehe TD mm U-iron on the x-axis: siehe TD mm total power requirement: 120 kW weight of the machine ca.: 78 t dimensions of the machine ca.: 6100 x 5150 x 4300mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

angle steel/side length: unbkt. mm double T-iron on the x-axis: unbkt. mm U-iron on the x-axis: unbkt. mm total power requirement: 30 kW weight of the machine ca.: 8,6 t dimensions of the machine ca.: 2500x2000x1900 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

round bar steel: 45 mm square edge steel: 42 mm L-beam: 140 x 13 mm flat steel: 350 x 20 mm pressure: 550 kN throat: 305 mm notching: rectangle tool: mm total power requirement: 5,5 kW weight of the machine ca.: 1260 kg dimensions of the machine ca.: 1360 x 750 x 1565 mm 2 working cylinder with 2 separated electric foot switch for 2-people-handling New notching table, new knife for the rectangle notcher and new punching table included For further information please see brochure. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

amplification -fold: ? diameter: 380 mm workpiece height max.: 200 mm voltage: 230 V weight of the machine ca.: 245 kg dimensions of the machine ca.: 0,80 x 1,20 x 2,00 m - Serial-No.: 1740 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.