printing press used for sale

AYEL-TECH WORKSHOP PRESS TYPE 30 WPM -Capaciteit 30 ton -Werkbreedte 600 mm -Hand mat-bedienbaar -Pressure gauge PRICE IS plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)

AYEL-TECH WORKSHOP PRESS TYPE WP 30 -Capaciteit 30 ton -Werkbreedte 700 mm -Electric of hand-mat bedienbaar -Pressure gauge -Noodstop -400V PRICE IS plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS

The nominal gain kN 4000 Slide stroke, mm 400 Frequency Slider strokes min-1, 25 The frequency of single strokes, min-1 19 Slider travel to its lowest position, where the press develops the rated force, mm 8 The distance between table and slider in its lower position at the upper adjustment position, mm 470 Size of adjustment of distance between table and slider, mm 160 The size of the table, mm 1000x1000 The size of the slide from front to back, mm 800 Width of windows in racks mm 600 Main electric motor power, kW 37.0 Air flow, m3 / stroke 0,017 Press overall dimensions, mm left to right 3470 front to back 3140 Height above floor level, mm 5940 Weight without hydro pillow kg 32600

Working width: 3500 mm Working height: 2300 mm Number of cylinders: 4 St. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Working width: 4000 mm Working height: 2600 mm Number of cylinders: 6 St. weight: 2000 kg Dimensions (L/W/H): 5550x1300x3000 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Used stainless steel pressure leave filter made by Filtro-Monoflux. Capacity 25 m3/h. Vertical plates, control panel, product pump, vacuum pump.

Used stainless steel filter press made by Seitz, type 40/30, new 1983. Filtration area 2,88 m2. 18 plates 40/40 cm. Hand clamp. New 1983. Available 2 pcs.

Working width: 3500 mm Working height: 2300 mm Number of cylinders: 4 St. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 3000 Working height: 2500 mm : 300-800 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Working width: 3500 mm Working height: 2650 mm Number of cylinders: nach Wahl St. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 1,0 t throat: 95 mm table length: 120 mm table width: 120 mm total power requirement: manuell kW weight of the machine ca.: 17 kg. dimensions of the machine ca.: 270x130x330 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press force max.:: 3000 kN heating plates:: 600 x 630 mm electrically heated:: °C heating power:: kW piston stroke:: 420 mm no. of stages:: 1 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

800 MT extrusion press 1. container size 127mm diam x 560mm lenght 2. capacity: extrusion: 800t/1000t extrusion (low tonnage) at 210kg/cm: 697M Ton Main ram forward at 210 kg/cm: 112 M Ton Main ram return at 210 kg/cm: 63 M Ton Contianer seal at 210 kg/cm: 69 M Ton Contianer open at 210 kg/cm: 94 M Ton Piercing at 210 kg/cm: 102 M Ton Mandrel return at 210 kg/cm: 63 M Ton Die slode at 210 kg/cm: 12 M Ton Stroke Main ram: 1320 mm Container: 250 mm Speed 38.0mm/sec 44.0mm/sec More information on request

Rotary vane vacuum & compressor - running dry Manufacturer: Becker Type: DVT 3.140 and DVT 3.100 Motor: 400V DS Suction power: 100 - 140m3/h Compression pressure/ vacuum: optional +-0.5bar / +-1.5 barStatus: Preliminary

; ready for operation

With the universal hand punch NPR-20 can both on the front page as also Center of the punch be punched, so may here A4 sheet at any point are processed. The punch is suitable for cutting of printed materials in the Office, in the printer or in the copy shop. With a Nutmesser can A4 sheets are grooved. The NPR-20 is suitable for all cutting work, which can be with the NPR-10 through out. A countertop if necessary Additionally facilitates the stamping work

Schuler PE4s 50/800 High Speed Press Manufacturer: Schuler Type: PE4s 50/800 High-speed press 61/21 600/3 Pressing force: 50 t Projection: 800 mm Stroke rate /min: 125-300 Plunger stroke: 40 mm Kohler unwinding reel 500.1 M We sell a large number of paternosters. The devices are in operation until 30.06.2021. After the purchase, there are also the documents for it From 01.07.21 the devices are ready for collection. Dismantling and transport by the buyer. Location is Hildesheim The dismantling, loading, as well as transport can alternatively be offered by us. In addition to about 50 paternosters, countless other machines are available. After purchase, the amount is due within 7 working days. Please also note our other offers. Have fun browsing and buying.

Multi-chamber press C400 | C600 | C800 C400 (with two pressing chambers) C600 (with three pressing chambers) C800 (with four pressing chambers) Specifications: Motor 1,5kW Electronic voltage 230V/50Hz/1-F. Maximum pressing force 6.5t Working pressure 150bar Cylinder stroke 700mm Time press cycle 50s Press chamber (LxWxH) 730x600x830mm Insertion height 1060mm Insertion opening (LxW) 730x600mm package size (LxWxH) 730x600x400mm Package weight 30-40kg Binding rolls 8x6x4x Strap type (polyester) 9mm/250m Number of containers 4x3x2x Length ges. 3455m; 2615mm; 1775mm; 17775mm Width ges. 1050mm Height ges. 1955mm Weight ges. 1955mm Weight ges. 1090kg; 880kg; 670kg; 510kg Transport dimensions C400 !x container Length 1680 mm 840 mm Width 845 mm 845 mm Height 1955 mm 1060 mm Weight ges. 210 kg Multi-chamber press C400 (with two pressing chambers) C600 ( ...

Force of pressure: 100 t projection: 350 mm table size: 690 x 840 mm Durchfalloch in the table: 160 mm table adjustment: slide area: 450 x 600 mm slide adjustment: 80 mm stroke adjustment: 8-100 mm stroke rate: 60 / min drive motor: 380 V, 5.5 kW space: 1850 x 1850 x 2650 mm weight: 6800 kg

A roll punching press for stamping is available up to A3. The die is pulled under the roll.

Brand Schiavi Model RG25/12 ID S24 Status Active Price 700 € + VAT Location Oradea, Romania

robuse two-hand operation with heavy adjustable stand Overall width approx 420 mm Overall height approx. 870-1120 mm Weight approx. 35 kg

Transmitting vessel with 2,000 l. gross content, inlet with pneumatic cone closure (incl. 1 spare cone), venting and outlet via pneumatic squeezing valves. Conveyor lines on the side of the building.

Qty. 1 Second-hand extrusion press Manufacturer: Loewy Type: 4 column floating - mandrel piercing press Aprox year of manufacture: 1939 Container size (dia.): 406 & 508 mm 16" and 20" Container size (length): 1350 mm Billet size (length): 1000 mm Nominal Extrusion Force: 5000 MT Nominal Piercing Force (Max): 740 MT Mandrel arresting Force floating mandrel Stroke Main ram: 2750 mm Piercer : 1200 mm

Baler, press for cardboard, film paper V5 | 5t Bale size: 700 mm H (variable) × 750 mm W × 500 mm D Bale weight: 50–100 kg Pressing time: 28 seconds Pressing force: up to 5 tons Dimensions: 2015 mm H × 870 mm W × 655 mm D Filling opening: 750 mm W × 385 mm H Integrated bale ejection mechanism Weight: 340 kg Power supply: Single-phase motor with 220 V 50 Hz 1.5 kW Noise: 70 decibels E-Power DIN EN 16500 IP54 protection class PLC with automatic cycle CE Certification V5 SMALL BALER Versatile, efficient and simple operation: The V5 baler is ideal for small and medium-sized companies. Even with a small amount of material, it creates order, cleanliness and space. The setting of the pressing cycle on the V5 can be done either automatically or manually. With the help of the "Easy Tie" system, the finished bale can be tied quickly and conveniently when the door is ope ...

Frequency-controlled heating laboratory press with force measuring device -Pressure 20 KN / 2 tons -Pressing area 220 220 mm -Maximum pressing force at 220 220 mm: 41 N / cm² -Hot press with moveable lower pressing plate, electric drive with gear reduction, force measurement is carried out by means of strain gauge sensor -Heat output approx. 1 KW -Plate temperature 120 ° C -Dwell time / duration of laminating: 1-10 s -Pneumatic connection 6bar required -Power supply 400 V, 16 A -Sliding table with integrated positioning pins, lower pressing plate, pneumatic drive -Pressing panels with switchable integrated vacuum channel -Electrical control system integrated with PLC control display in the front panel of the machine -Side channel pump to generate the vacuum

Plywood Press, manufactured by Siempelkamp, working sizes 2500 x 1300, 10 floors

Rotary vane compressor Manufacturer: Becker Type: VT4.25 Voltage: 400V/50Hz Performance: 12 months Status: Generalueberholt and repainted Printing capacity: 25m3/h End printing: max+ +1 bar (rel) Zubehoer: Ready to use

The CE10 series is an electrically driven high-pressure cleaner. This model is the ideal tool for general cleaning work. Built into a stainless steel frame, this robust high-pressure cleaner is easy to move and can be equipped with various accessories, such as rotor nozzles, chemical injectors and a sandblasting kit. Similar but no Dynajet, Falch, Kärcher, Oertzen, etc. Available models: ----- CE10-200 50Hz 200 bar 21 l/min. CE10-200 60Hz 200 bar 25 l/min. General Specifications: ----- Power of the drive motor: 7.5 kW (50Hz) / 9 kW (60Hz) Volts: 400V (50Hz) - 440V (60Hz) Amp: 15.1A (50Hz) - 15.6A (60Hz) Dimensions: 690 mm x 560 mm x 900 mm Weight: 70 kg Includes standard accessories.

The CE15 series is an electrically driven high-pressure cleaner. This model is the ideal tool for general cleaning work. Built into a stainless steel frame, this robust high-pressure cleaner is easy to move and can be equipped with various accessories, such as rotor nozzles, chemical injectors and a sandblasting kit. Similar but no Dynajet, Falch, Kärcher, Oertzen, etc. Available models: ----- CE15-170 50Hz 170 bar 40 l/min. CE15-200 50Hz 200 bar 36 l/min. CE15-200 60Hz 200 bar 30 l/min. CE15-300 50Hz 300 bar 18 l/min. CE15-300 60Hz 300 bar 22 l/min. General Specifications: ----- Drive motor power: 11.2 kW (50Hz) / 13 kW (60Hz) Volts: 400V (50Hz) - 440V (60Hz) Amp: 22.8A (50Hz) - 23.8A (60Hz) Dimensions: 690 mm x 600 mm x 900 mm Weight: 85 kg Includes standard accessories.

The CE20 belongs to the series of our electrically operated high-pressure machines with a pressure of 200 to 500 bar and a volume flow of 16 to 45 l/min. The standard version has hard rubber tyres with a parking brake at the rear and swivel castors at the front. The "Slim version" has a narrower design and also has narrower rear wheels with a parking brake. The frame consists of hot-dip galvanized and powder-coated sheet metal molded parts with circumferential stainless steel side frames. The standard model has a dimension of 1060 x 760 mm. The "Slim" version has a very compact dimension of 1060 x 500 mm. Both versions are 850 mm high. The standard and slim versions are identical in all other specifications. Similar but no Dynajet, Falch, Hammelmann, Kamat, Kärcher, Oertzen, Uraca, Woma, etc. Available models: ----- CE20-200 50Hz 200 bar 38 l/min. CE20-200 60Hz 170 bar 45 l/min.  ...

The CE40 belongs to the series of our high-pressure machines with an electric drive for a pressure of 100 to 2000 bar and a volume flow of 9 to 160 l/min. The frame consists of hot-dip galvanized sheet metal moldings and circumferential stainless steel side frames. The front wheel and the two large rear wheels including a parking brake ensure easy manoeuvring and stable stationing. A lifting eyelet facilitates transport. Similar but no Dynajet, Falch, Hammelmann, Kamat, Kärcher, Oertzen, Uraca, Woma, etc. Available models: ----- 50 Hz-bar-l/min. CE40-100-160 CE40-160-100 CE40-230-75 CE40-400-40 CE40-550-30 CE40-700-23 CE40-800-20 CE40-1000-18 CE40-1250-13 CE40-1380-12 CE40-2000-9 60 Hz and others see data sheet and on request. General Specifications: ----- Power of the drive motor: 30 kW (50Hz) / 33 kW (60Hz) Volts: 400V (50Hz) - 440V (60Hz) Amp: 57A (50Hz) - 57A ...

- Pressing area 2 x 1240 x 1250 mm - total pressure 2 x 25 to - max. opening width 1000 mm - total connection 4.0 kW - dimensions L=3000, W=1250,H=3050 mm - weight 2850 kg

The CE100 series is an electrically driven high-pressure machine for a pressure of 300 to 2000 bar and a volume flow of 21 to 135 l/min. The frame consists of hot-dip galvanized sheet metal moldings and stainless steel side frames. Four rubber feet ensure secure positioning. The lifting eyelet makes it easier to transport the machine. Similar but no Dynajet, Falch, Hammelmann, Kamat, Kärcher, Oertzen, Uraca, Woma, etc. Available models: ----- 50 Hz -bar-l/min. CE100-300-135 CE100-500-80 CE100-1000-42 CE100-1400-28 CE100-2050-21 60 Hz and others see data sheet and on request. General Specifications: ----- Power of the drive motor: 75 kW (50Hz) / 90 kW (60Hz) Volts: 400V (50Hz) - 440V (60Hz) Amp: 81A (50Hz) - 108A (60Hz) Dimensions: 1800 mm x 1050 mm x 1400 mm Weight: 2000 kg Includes standard accessories.

The CE125 series is an electrically driven high-pressure machine for a pressure of 200 to 2500 bar and a volume flow of 21 to 240 l/min. The frame consists of hot-dip galvanized sheet metal moldings and stainless steel side frames. Four rubber feet ensure secure positioning. The lifting eyelet makes it easier to transport the machine. Similar but no Dynajet, Falch, Hammelmann, Kamat, Kärcher, Oertzen, Uraca, Woma, etc. Available models: ----- 50 Hz -bar-l/min. CE125-200-240 CE125-1500-35 CE125-2500-21 60 Hz and others see data sheet and on request. General Specifications: ----- Power of the drive motor: 90 kW (50Hz) / 90 kW (60Hz) Volts: 400V (50Hz) - 440V (60Hz) Amp: 81A (50Hz) - 108A (60Hz) Dimensions: 2150 mm x 1385 mm x 1750 mm Weight: 2000 kg Includes standard accessories.

The CE150 series is an electrically driven high-pressure machine for a pressure range of 200 to 2500 bar and a volume flow of 21 to 300 l/min. The frame consists of hot-dip galvanized sheet metal moldings and stainless steel side frames. Four rubber feet ensure secure positioning. The lifting eyelet makes it easier to transport the machine. Similar but no Dynajet, Falch, Hammelmann, Kamat, Kärcher, Oertzen, Uraca, Woma, etc. Available models: ----- 50 Hz -bar-l/min. CE150-200-240 CE150-250-200 CE150-1000-50 CE150-1400-33 CE150-2500-21 60 Hz and others see data sheet and on request. General Specifications: ----- Drive motor power: 90 kW (50Hz) / 110 kW (60Hz) Volts: 400V (50Hz) - 440V (60Hz) Amp: 160A (50Hz) - 180A (60Hz) Dimensions: 2100 mm x 1200 mm x 1400 mm Weight: 2200 kg Includes standard accessories.

The CE200 series is an electrically driven high-pressure machine for a pressure range of 200 to 2500 bar and a volume flow of 25 to 350 l/min. The frame consists of hot-dip galvanized sheet metal moldings and stainless steel side frames. Four rubber feet ensure secure positioning. The lifting eyelet makes it easier to transport the machine. Similar but no Dynajet, Falch, Hammelmann, Kamat, Kärcher, Oertzen, Uraca, Woma, etc. Available models: ----- 50 Hz -bar-l/min. CE200-200-280 60 Hz -bar-l/min. CE200-200-350 and others on request. General Specifications: ----- Power of the drive motor: 150 kW (50Hz) / 150 kW (60Hz) Volts: 400V (50Hz) - 440V (60Hz) Amp: 160A (50Hz) - 180A (60Hz) Dimensions: 2100 mm x 1200 mm x 1400 mm Weight: 2200 kg Includes standard accessories.

The CP22 belongs to the series of gasoline-powered high-pressure machines with a pressure of 170 to 500 bar and a volume flow of 16 to 46 l/min. The machine has pneumatic tyres with a parking brake on the rear axle and swivel castors on the front axle. The frame consists of hot-dip galvanized and powder-coated sheet metal molded parts with circumferential stainless steel side frames. The machine measures 1060 x 760 mm and is 850 mm high. The Honda engine is equipped with electric starter. Similar but no Dynajet, Falch, Hammelmann, Kamat, Kärcher, Oertzen, Uraca, Woma, etc. Available models: ----- Model Pressure Volume Flow CP22-170 170 bar 46 Lpm CP22-220 220 bar 36 Lpm CP22-280 280 bar 27 Lpm CP22-350 350 bar 23 Lpm CP22-500 500 bar 16 Lpm General Specifications: ----- Drive motor: 2 Cylinder 4 Stroke Petrol Engine, Electric Start Power of the drive motor: 16.4 kW Spee ...

The machines of the CD25 series are compact high-pressure cleaners from 170 to 500 bar and a volume flow of 17 to 42 l/min. The pump is powered by a 3-cylinder, water-cooled Kubota diesel engine. The sturdy frame is made of stainless steel for long durability and corrosion resistance. The powder coating ensures the very beautiful appearance. The machine has very compact dimensions of 1200mm x 800mm. This corresponds to the same size as the well-known EURO pallet. The frame is fixed on 4 large rubber feet. The high-pressure machine is also equipped with forklift pockets and a central lifting eyelet. This allows for very easy transport. Similar but no Dynajet, Falch, Hammelmann, Kamat, Kärcher, Oertzen, Uraca, Woma, etc. Available models: ----- Model Pressure Volume Flow CD25-170 170 bar 42 Lpm CD25-250 250 bar 32 Lpm CD25-350 350 bar 23 Lpm CD25-400 400 bar 21 Lpm CD25-500 500  ...

The CD50 series of our high-pressure machines covers a pressure of 230 to 2000 bar and a volume flow of 7 to 74 l/min. The pump is powered by a water-cooled 4-cylinder Toyota diesel engine. The fully enclosed frame is made of hot-dip galvanized steel to ensure a long service life and corrosion resistance. The frame is primed and then painted. The machine only requires a footprint of 1550 x 920 mm. Under the frame 4 rubber feet are mounted. In addition, the machine has forklift pockets and lifting eyelets attached to all four corners. For the protection and storage of, for example, high-pressure hoses, a galvanized roof plate provides. Similar but no Dynajet, Falch, Hammelmann, Kamat, Kärcher, Oertzen, Uraca, Woma, etc. Available models: ----- Model Pressure Volume Flow CD50-230 230 bar 74 Lpm CD50-400 400 bar 40 Lpm CD50-500 500 bar 33 Lpm CD50-700 700 bar 25 Lpm CD50-1000 100 ...

The CD100 series of water and water jet machines ranges from 250 to 2050 bar with pump flows from 21 to 167 l/min. The pump is powered by a water-cooled 4-cylinder turbo SISU diesel engine. The frame surrounding all frames is made of hot-dip galvanized steel to ensure long service life and corrosion resistance. It is primed and painted. The footprint of the machine is 2100 x 950 mm. The frames are equipped with rubber feet under all four corners and the machine has forklift pockets as well as hanging eyelets at all four corners. The machines have galvanized roof panels with side railings for the protection and storage of, for example, high-pressure hoses. Similar but no Dynajet, Falch, Hammelmann, Kamat, Kärcher, Oertzen, Uraca, Woma, etc. Available models: ----- Model Pressure Volume Flow CD100-250 250 bar 167 Lpm CD100-300 300 bar 135 Lpm CD100-500 500 bar 80 Lpm CD100-1000 1 ...

The CD160 series of our high-pressure machines covers a pressure of 200 to 2500bar and a volume flow of 25 to 300 l/min. The pump is powered by a water-cooled 4-cylinder SISU diesel engine with turbocharging and charge air cooling. The entire frame is made of hot-dip galvanized steel, which ensures long durability and corrosion resistance. For the beautiful look, the frame is primed and then painted. The dimensions of the machine are 2250 x 950 mm. The frame is equipped with rubber feet, forklift pockets and, at all four corners, with lifting eyelets. The machine has a galvanized roof plate with a side bracket for the protection and storage of, for example, high-pressure hoses. Similar but no Dynajet, Falch, Hammelmann, Kamat, Kärcher, Oertzen, Uraca, Woma, etc. Available models: ----- Model Pressure Volume Flow CD160-200 200 bar 300 Lpm CD160-250 250 bar 250 Lpm CD160-1000 1000 ...

With the universal hole punch NPR-20 can both on the front page as also Center of the punch be punched, so may here A4 sheet at any point are processed. The punch is suitable for cutting of printed materials in the Office, in the printer or in the copy shop. With a Nutmesser can A4 sheets are grooved. The NPR-20 is suitable for all cutting work, which can be with the NPR-10 through out. A countertop if necessary Additionally facilitates the stamping work.

AYEL-TECH WORKSHOP PRESS TYPE WP 15 -Capaciteit 15 ton -Cilinderslag 260 mm -Werkbreedte 500 mm -Electric of hand-mat bedienbaar -Pressure gauge -Noodstop -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)

; neu, sofort lieferbar

SAY MAK WORKSHOP PRESS TYPE WP 100 -Capaciteit 150 ton -Cilinderslag 400 mm -Werkbreedte 1100 mm -Verplaatsbaar cilinder is -Pressure gauge -Met V-Blokken -Noodstop -Documentatie -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)

System: Mobile dewatering system on trailer Type: Chamber filter press 500 x 500 Execution: filter press Year of constr.: 2017 refurbished Number of plates: 5 + head and end plate Filter plates: PP Filter cloths: optionally available in voting on the medium Presses contents: approx. 130 dm3 Filter pressure: 15 PSI Material: product-contacting parts flange, traverses stainless steel, PP or rubberized Material: non-product-contacting parts stainless steel Pump technology: In consultation System: The system is delivered as turnkey dewatering equipment ready to plug. Visit: the systems in consultation with us in the work. Other: we deliver the equipment you used ready or refurbished adapted according to your wishes and requirements.

SAY MAK WORKSHOP PRESS TYPE SHP 100 -Capaciteit 100 ton -Cilinderslag 400 mm -Werkbreedte 1000 mm -Verplaatsbaar cilinder is -Pressure gauge -Met V-Blokken -Noodstop -Documentatie -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)

SAY MAK WORKSHOP PRESS TYPE SRHP 250 -Capaciteit 250 ton -Cilinderslag 400 mm -Werkbreedte 1200 x 1000 mm -Slaginstelling -Pressure gauge -Noodstop -Weight 3450 kg -Power 11 kVA -Documentatie -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)

Capacity: 0 t Table length: 0 mm Table width: 0 mm Stroke: 0 mm CNC Brand: 0 CNC Model: 0 Technical data Pressure: 1600 kN Total stroke: 300 mm Execution: 4 columns Table surface: Length: 1000 mm Width: 850 mm Return power: 119 kN Depth of throat Passage between columns: longitudinal: 645 mm Lateral: 405 mm Slide clamping surface: Width: 1000 mm depth: 850 mm Close traverse speeds: Rapid traverse: 400 mm/s Press stroke: 10 - 60 mm/s Return traverse speeds: 400 mm/s Oil quantity: 350 l Voltage 50 Hz 3x: 380 Volt Motor power: 45 kW Machine´s weight about: 13000 kg Overall dimensions machine: Length: 2100 mm Width: 1200 mm Height: 3900 mm Various accessories: Security/savety device: SICK Roll-feed Useful cylinder length: 250 mm Decoiler: Manufacturer: DREHER 2380DM 400 mm Straithening device: DREHER 400 x 4 mm