134,663 used machines on RESALE, but how to find them? Machine Search
KSB VF35-5 Movitec high-pressure inline pump 11 kW Manufacturer: KSB Type: Movitec VF32 5 ID No.: 47110112 Maximum flow rate: 27 m³/h Maximum flow rate: 2850 l/min Mains voltage: 3~400/690 V Degree of protection: IP55 Power: 11 kW 21.8 A You can find more centrifugal pumps - new and used - in our shop! International shipping costs on request!
System for pressure increase or constant pressure maintenance, e.g. for the fresh water inlet of bottle washers 1.5 m³ stainless steel tank with frequency-controlled pump (see pictures for performance) Level control
pressure:63 t throat:350 mm stroke:400 mm dayligth:650 mm total power requirement:8 kW weight of the machine ca.:4 t dimensions of the machine ca.:3 x 1,9 x 2,7 m
Pressure total: 80 - 800 ton Ram stroke: 1600 mm Free frontal opening L-R: 2850 mm Free lateral opening F-B: 1000 mm Daylight: 1900 mm Table surface area : 2800 x 2000 mm Slide area: 2800 x 2000 mm Die cushion capacity in table: 32 - 320 ton Die cushion stroke: 400 mm Die cushion pad area: 2500 x 1700 mm Approach speed: 400 mm / sec Working speed: 5 -42,7 mm / sec Return speed: 420 mm / sec Required power: 246 kW Height over floor approx.: 7785 mm Weight of machine approx.: 100 ton No. of moving bolster: 1 pcs.
Pressure total: 140 ton Stroke: 800 mm Daylight: 1.004 mm Free frontal opening L-R: 2.060 mm Table surface area : 2.000 x 520 mm Slide area: 2.040 x 520 mm Working speed: 4 -20 mm / sec Rapid travel: 135 mm / sec Return speed: 120 mm / sec Weight of machine approx.: 14 ton Height over floor approx.: 4.810 mm Oil volume: 700 l
Pressure total: 1400 ton Stroke: 950 mm Daylight: 2000 mm Table surface area : 3600 x 2500 mm Slide area: 3600 x 2500 mm Die cushion capacity in table: 400 ton Die cushion stroke: 500 mm Die cushion pad area: 3060 x 1860 mm Approach speed: 400 mm / sec Working speed: 40 / 80 mm / sec Return speed: 400 mm / sec Oil volume: 5000 l Required power: 450 kW Weight of machine approx.: 240 ton
Pressure total: 500 ton Stroke: 1100 mm Daylight: 1500 mm Table surface area : 2000 x 1250 mm Slide area: 2000 x 1250 mm Die cushion capacity in table: 160 ton Die cushion stroke: 300 mm Approach speed: 650 mm / sec Required power: 55 kW Weight of machine approx.: 50 ton
Ø 100, class 1.6 0 - 25 bar Version: Vertical Display range: 0 - 25 bar Scale graduation: 0.5 bar Materials: Housing 1.4571, measuring system and connection, viewing panel multi-layer safety glass Connection: 1/2'' bottom (AB) Plate spring pressure gauge
Screw press for cold pressing of oilseeds - Manufacturer: Reinartz - Type: AP 10/06 - Power: 7.5 kW - Processing capacity (rapeseed): 100 kg/h - Processing capacity (other oilseeds): 70 kg/h - Length: 1900 mm - Width: 600 mm - Height: 1100 mm - Weight: 900 kg
Single column pneumatic press, hydraulic press PAUL ANTON type PVT 2Pneumatic table press, embossing pressFabr. No. 97148 Year of construction approx. 1980Compressive force: 10 tonProjection: 100 mmPlunger stroke: approx. 25 mmPlunger surface: 32 mmTable size: 250 x 220 mmTable opening: 53 x 53 mmTable height: 1060 mmInstallation height: 155 mm- very stable construction- Hydro-pneumatic press with pressure transmission air on oil- pneumatic foot switch- Plunger with internal thread M12- Metal substructureSpace requirement L x W x H 850 x 620 x 1560 mmWeight
Hydr. Spotting press MILLUTENSIL type BV 25 PMMasch. No. 632 / 25111 Year of construction 1991Clamping force 18 ton. Opening force 15 ton. Table surface 775 x 760 mm Clamping surface of the upper table 900 x 550 mmStand width 900 mmInstallation height max. 750 mmInstallation height min. 230 mmStroke of the upper table 520 mmLifting speed stepless 0 - 1000 mm/min. Hydraulic pressure adjustable 10 - 200 barTool weight on the table max. 2500 kgTool weight on the upper table max. 800 kgTable height
Pressure total: 315 ton Stroke: 1100 mm Daylight: 2200 mm Table surface area : 2500 x 1000 mm Slide area: 2500 x 1000 mm Die weight at the ram max.: 6000 kg Approach speed: 600 mm / sec Working speed: 32 - 230 mm / sec Return speed: 600 mm / sec Required power: 158 kW Weight of machine approx.: 44 ton Height over floor approx.: 6175 mm
Single column - eccentric press KRUPP type PEKRD 125 hMasch. No. 2861 Year of construction 1977Compressive force 125 ton. Projection 400 mmTable size 950 x 750 mmPlunger area 800 x 540 mmTable opening 100 x 250 mmStroke adjustment 8 to 160 mmPlunger adjustment 100 mmInstallation height largest stroke at the top max. 550 mmStroke rate 60 strokes/min. Table height above floor 800 mmEngine power 10 kWNetz connection 380 Volt, 50 Hz- Hydraulic overload in the plunger- Compressed air clutch-brake combination ORTLINGHAUS-
Single column hydraulic press, straightening press, punching bracket ECKOLDPressen frame with hydraulic cylinder, mobile press, punching unitType RSD 1500 - 125Masch. No. 317 / 690 Year of construction approx. 1986Compressive force 150 ton. Projection 125 mmSlide stroke 35 mmTable size 280 x 210 mmPlunger area 125 mmInstallation height (plunger to table) max. 265 mmTable height above floor 403 mmHydraulic operating pressure max. 500 bar- without hydraulic unit- Lifter surface with 4 threads M16 and 20 mm guide groove, one centering hole in the middle 15
Single column hydraulic press SCHÖN type TES/CBbuilt in 1977Compressive force 63 ton. (160 bar)Projection 320 mmTable size 600 x 770 mmPlunger area 600 400 mmPlunger stroke 125 mmInstallation height max. 400 mm (with intermediate plate on the ram)Slide speed Rapid traverse downwards approx. 180 mm/sec. Ram speed work approx. 25 mm/sec. Pushrod speed upwards approx. 180 mm/sec. Table height above floor 870 mmDrive power 22 kWNet connection 380 volts, 50 HzTank capacity approx. 280 litres Hydraulic oil
Pneumatic toggle press, pneumatic press SCHMIDT type 34-12Fabr. No. 400160-03 Serial No. 0028 Year of manufacture 2008Compressive force 28 kN = 2.8 ton. Throat depth 130 mmPlunger area 63 x 36 mmPlunger stroke 12 mmPin hole 20 mm with clamping screwCompressed air requirement 2 to 6 bar- Stroke length infinitely variable via adjustable fixed stop for the upper end of stroke position- Fine adjustment for lower end of stroke position with scale 1 tick = 0.05 mm- Stroke triggered via pneumatic valve, triggered by material insertion- Press stand 45 off
Mäder DLP 1700 HV Direct Acting Air Press Press Direct-acting air presses are used wherever the compressive force is required constantly over a longer distance or where a large immersion depth is required: e.g. when pressing pins, bushings and ball bearings or when forming. DLP 1700 HV Direct-acting compressed air press Compressive force at 6 bar: 17 kN Working Stroke: H mm: 40/60/80 More items - new and used - can be found in our shop! International shipping costs on request!
Pressure total: 2000 ton Ram stroke: 900 mm Slide adjustment: 800 mm Shut height (stroke down, adjustment up): 1800 mm Free frontal opening L-R: 5040 mm Distance between oil tray: 4840 mm Distance between the columns F - B: 2600 x 2400 mm Table surface area : 5000 x 2700 mm Slide area: 5000 x 2700 mm Die cushion capacity in table: 400 ton Die cushion stroke: 350 mm Die cushion pad area: 4200 x 2100 mm Cushion pressure in ram: 200 ton Ejector stroke in ram: 200 mm Number of strokes: 8 - 14 s.p.m. Required power: 350 kW Height over floor approx.: 11350 mm Die weight at the ram max.: 40000 kg Die Weight total: 80000 kg Weight of machine approx.: 580 ton
Pressure total: 2000 ton Ram stroke: 900 mm Slide adjustment: 800 mm Shut height (stroke down, adjustment up): 1800 mm Free frontal opening L-R: 5040 mm Distance between oil tray: 4840 mm Distance between the columns F - B: 2600 x 2400 mm Table surface area : 5000 x 2700 mm Slide area: 5000 x 2700 mm Die cushion capacity in table: 400 ton Die cushion stroke: 350 mm Die cushion pad area: 4200 x 2100 mm Cushion pressure in ram: 200 ton Ejector stroke in ram: 200 mm Number of strokes: 8 - 14 s.p.m. Required power: 350 kW Height over floor approx.: 11350 mm Die weight at the ram max.: 40000 kg Die Weight total: 80000 kg Weight of machine approx.: 580 ton
Frame press, gluing press -operated: hydraulically -Working area up to: 3500 x 2400 mm -Wood clamping: pneumatic -Display dimensions: 4200/1100/H3700 mm -Transport dimensions: 4200/1200/H2300 mm -Weight: approx. 3500 kg
Pressure total: 800 ton Ram stroke: 700 mm Slide adjustment: 600 mm Shut height (stroke down, adjustment up): 1500 mm Free frontal opening L-R: 3800 mm Free lateral opening F-B: 1450 x 1100 mm Table surface area : 3500 x 1900 mm Slide area: 3500 x 1900 mm Die cushion capacity in table: 150 ton Die cushion stroke: 250 mm Die cushion pad area: 2780 x 1570 mm Number of strokes: 7 - 18 s.p.m. Required power: 120 kW Height over floor approx.: 9510 mm Weight of machine approx.: 260 ton
1 shaft with direct gear drive; Feeding spiral is driven by gearbox; Mouthpieces and spare parts are provided separately on pallet; Control cabinet with control (in need of renewal) is included; Length 3.70 m, width 1.10 m, height without hopper 1.35 m, hopper height 0.50 m, inlet opening 35 x 35 cm Current type: 3-phase AC; Operating voltage 380 V; connected load 2.5 kW, motor type KMR 160 M8; Engine power 11 kW; Engine speed 720 rpm. The plant was shut down in 2024. more photos on request
Pressure total: 140 ton Stroke: 800 mm Daylight: 1.004 mm Free frontal opening L-R: 2.060 mm Table surface area : 2.000 x 520 mm Slide area: 2.040 x 520 mm Working speed: 4 -20 mm / sec Rapid travel: 135 mm / sec Return speed: 120 mm / sec Weight of machine approx.: 14 ton Height over floor approx.: 4.810 mm Oil volume: 700 l
Pressure total: 250 ton Ram stroke: 70 / 250 mm Slide adjustment: 160 mm Ejector in ram: 20 ton Ejector stroke in ram: 10 mm Shut height (stroke down, adjustment up): 520 mm Free lateral opening F-B: 1.300 mm Table surface area : 1.600 x 1.600 mm Slide area: 1.600 x 1.600 mm Number of strokes: 0 - 50 s.p.m. Required power: 33 kW Height over floor approx.: 5.500 mm Weight of machine approx.: 58 ton Roll feeder Material width: 1250 mm Material thickness: 0,3 - 1,6 mm Control: Siemens S7
Equipment: Overpressure,Manufacturer: W. Ortmann,Condition: used,Volume: 6,000,Max. overpressure: 8.0,Design: lying,Base: feet,Number of feet: 4,Diameter inside: 1,580,Cylindrical length: 2500,Total height: 1,900,Total length: 3,500,Wall thickness floors: 5,Wall thickness cylinder: 5,Technical documents: Drawing, Acceptance certificate,Type plate: Yes,Outlet: DN40 DIN 11851,Note: slight adhesions,Remarks: 1 oval manhole (approx. 420 x 320mm) in the front floor Information in the drawing different loose fittings in the tanks were not correct for the cylinder length (were not correctly installed when the
Pressure total: 2000 ton Stroke: 1500 mm Daylight: 2000 mm Table surface area : 5000 x 2500 mm Slide area: 5000 x 2500 mm Die cushion capacity in table: 100 - 600 ton Die cushion stroke: 400 mm Die cushion pad area: 4000 x 1800 mm Cushion pressure in ram: 50 - 300 ton Approach speed: 200 mm / sec Working speed: 20 - 30 mm / sec Return speed: 200 mm / sec Oil volume: 5000 l Required power: 2 x 250 kW Weight of machine approx.: 360 ton
Pressure total: 100 ton Daylight: 1.400 mm Table surface area : 1.300 x 1.000 mm Slide area: 1.300 x 1.000 mm Ejector Force: 35 kN max. capacity of swivelling ram plate: 40 kN Die Weight on table max.: 80 kN max. capacity of tilting table: 50 kN Oil volume: 200 l Required power: 10 kW Dimensions L x W x H: 3.95 x 2.3 x 4.5 m Distance between the columns F - B: 1.050 mm Weight of machine approx.: 10 ton
For sale is an 800 to step press. Technical data see photos. Press we sell from location.
Press has made about 2,7 million peaces so far, and large factories make over 10 million pieces with these machines. The maximum theoretical diameter of the pieces is 380 mm, production-wise max. 320 - 340 mmfinished size. Depth 110 mmfinished measurement . Speed: small objects 300 - 350 pcs/h large ones 120 - 160 pcs/h. Between 2004 - 2010, less than 2 million pieces were driven on the Press, and after that the demand for the products has degreased and today it is driven only a few hours a week, sometimes the press stands unused for a couple of weeks.
Cat.-Nr. 11-1045 Capacity: 500 up to 1000 Litres COMPLETE For producing juice and filling in from fruits and vegetables For Washing/Grinding, Pressing, Storing, Pasteurizing, Filling Complete Production Line with following machines: Cat-Nr 10-2346 - Eurolux Big-Box Dumper for emptying fruits and vegetables from wood or OVC boxes LxWxH: 1680 x 1480 x 1220 mm Cat-Nr 10-2347 – Eurolux Wash and Grinding Mill Unit Capacity: 2000 kg/h - Motor Power: 3,0 kW Cat-Nr 10-2337 – Eurolux Automatic Continuous Belt Press EL-500 for producing fruit juice and fruit wine, cider from apples, pears Capacity: 500 up to 1000 kg/h Cat-Nr 06-1101 – Eurolux Floating Lid Tanks 2 x 1000 Litres Floating Lid Tanks 2 x 500 Litres Floating Lid Tanks 2 x 300 Litres Floating Lid Tanks Cat-Nr 10-2350 – Eurolux Pasteurizing Machine EL-1500 with Plate Heat Exchanger Capacity: 10 ...
Stand drilling machine in row arrangement, used Gang drilling machine, used Type: BT 6.52 Manufacturer / make: Steinel Built/ new in: 1978 Drilling capacity / drilling capacity: 6 mm in St 60 Spindle cone/ spindle taper: MK 1 Drilling spindle discharge / distance center drill spindle to column: 204 mm Drilling stroke/ way of spindle: 90 mm Table clamping area/ table size: 800 x 390 mm Column diameter/ diam. of coulmn: 60 mm Drilling spindle speeds / speeds of drilling spindle: 1400 / 2800 / 5600 per min/ per minute Total connection value / rated power: 0.25 kW each => 1 kW Weight / weight: approx. 0.4 t
used
1 x Adamson 96in wide x 32in dia 4 roll Z Calender line, peripherally drilled rolls with oil heating, motorised nip adjustment to rolls 1,2 and 3 (roll 4 fixed). Cross axis roll 4. Hydraulic pre-load to all rolls, Adjustable stock guides, rubber coated pressure roller with hydraulic adjustment and v/s motor to roll 4, with Adamson unidrive gearbox on universal couplings, with 500HP, 850/1300rpm, 785A, 500V, 3ph, 60Hz Reliance DC variable speed motor to rolls 1, 2 and 3. 200HP, 850/1400rpm DC variable speed motor to roll 4. 1 x Embossing station 1 x set of 8 x 96in wide x 24in dia stainless steel cooling drums. 1 x Dual turret winder. Full drawings available. We can supply the upstream equipment I.e. internal mixers that fed the calenders, along with the batching and material handling/dosage equipment. Complete line available in very good condition previously us ...
Precast - Wall - Filigree - factory. Good as new circulation system: 60 pallets with 3.5 mx 8 m, 3 x lateral transport of pallets - Facilities, 1 x vibrated concrete station, new control - Beckhoff. Concrete distributor Crane 1.4 m³. Friction wheels. Roller blocks. Planning and installation as required. Formwork on request. Is dependend on the application. For low cost housing, cmodul austria low cost housing Affordable housing Low-cost housing Mixing system 1 m³ at extra charge. Tilting device if needed for concrete slabs vertical-tansport at extra charge. Cran for stock handling at extra charge. Projects for social housing are our daily work. Civil work plans, drawings and calculations, we can create for you. Similarly, profitability calculations.
Rodolfo Comerio 5 roll 'L' calender, Year: 1981, Peripherally drilled hard chrome plated rolls 650mm dia x 2400mm wide (2 spares), High pressure hot water heating (28 bar), Roller bearings, Motorised nip adjustment, Roll bending on rolls 2,4 and 5, Cross axis on rolls 1 and 4, With Farrel Pomini full unidrive gearbox (choiceable 2 speed 30m/min or 60m/min), dc variable speed motor to each roll 88.2kW to rolls 1,3,4 + 5, 110kW to roll 2?. Motors not included. Previously used for rigid PVC film 2000mm finished width, 100micron - 1100micron. Calender max speed 60m/min. Post calender equipment:- 7 x Take off rolls? 150mm dia x 2200mm wide (3 groups), Hydraulic embossing station 300mm dia x 2200mm wide (rubber roll driven, emboss roller free running against rubber roller), 12 x cooling drums (4 groups) 180mm dia x 2200mm. Beta thickness gauge (not available) Berstorff edge ...
Used line for packaging of powdery materials in plastic buckets from 2.5 kg to 10 kg. Semi-automatic line of packing and transporting the dispenser weight The line consists of: Two unloading of big bags Oblique conveyor The buffer tank Two batchers Stacking conveyor The set of the transporters with the balance cruise control, feeder lids and closing buckets, made as part of the line for packing powdery materials. The line consists of: Conveyor separator Cruising verified checkweigher Discriminator transporter odstawiaj?cym Conveyor feeder lids Crimper Stacking Conveyor Appetizer - welding machine for bags The checkweigher DWT / xx Technical data: Supply voltage - Uz = 230V Isaiah znamionowy- current = 2-5A (depending on version) Mains frequency - f = 50 Hz overcurrent - F = 10A recommended network layout -TNS Insulation class - I New 2010
maximum number of results exceeded
please refine your search
1.000 € 
