126,706 used machines on RESALE, but how to find them? Machine Search
used
Haco PPH 135 ton x 4100 mm CNC Capacity: 135 ton x 4100 mm Backgauge: CNC Control: Delem DA-41T Passage between uprights: 3600 mm Max stroke: 120 mm Max distance between table -- ram: 325 mm Depth of throat: 250 mm Table width: 180 mm Locking speed: 70 mm/sec Working speed: 7,2 mm/sec Returning speed: 62 mm/sec Electric motor (power): 11 kW Length: 4270 mm Depth: 1500 mm Height: 2470 mm Weight: 9,1 ton
RONCHI TABLET PRESS, MODEL PA20 Year of manufacturing: 2003 High-speed tablet press for the dosage, pre-compression and compression of solids for the production of tablets. For use with Euro D tools. Documentation available. CHARACTERISTICS • Tool size: Euro D PRODUCTION • Production capacity: 56,000 tablets/h • Punches sizes available: Ø20 mm (complete) + Ø8 / Ø11 / Ø13 / Ø16 (4 punches + covers for small production runs) Number of punches: 20 units • Max. tablet diameter: 25 mm • Max. compression force: 10,000 Kg DIMENSIONS • Size: 83 x 130 x 175 cm
Inv. Num. : 8630 Type: EHP 50 Producer: Darley Created: 1997 Parameters: Control system: DELEM Compressive force: 50 t Maximum bending length: 2000 mm Machine weight: 2600 kg
Capacity (ton) 315 Table size, mm 2500 x 1250 Slider stroke, mm 400 Shut height,mm 750 Strokes per min 25 Press weight, kg 50900
CONTROLS PC controller BECKHOFF PRESS DESIGN drive system: servohydraulic frame design: H-frame, tie rod quick die change system: yes feedstock transport direction: left to right SLIDE total force (nominal): 1100 to stroke: 130 mm stroke rate (max.): 60 /min COUNTER RAM nominal force: 330 to stroke: 40 mm V-RING nominal force: 500 to stroke: 40 mm TOOL DIMENSIONS lower table (left-right): 960 mm lower table (front-back): 960 mm upper table (left-right): 960 mm upper table (front-back): 960 mm shut height max.: 470 mm OVERALL SPECIFICATIONS (COIL LINES) sheet width max.: 500 mm sheet thickness max.: 16 mm coil weight max.: 8 to feedstock t ...
Used machine, Woma / Kärcher Ecotherm, hot water Working pressure: 500 bar flow 27 lpm, Year of construction 2009 Drive: Diesel 36.5 kW, Kubota V 2403 Diesel Operating hours: approx.: 645 h,
Press brake with Stäubli robot cell press Manufacturer: LA G Model: GBS R 1250 50 The machine was only used for a very short period of time.
Met elektrische achteraanslag Ponscapaciteit: 70 ton Dia x plaatdikte: Ø 28 x 20 mm Maximale slag: 80 mm 40 str / min Keeldiepte: 300 mm Werkhoogte: 1065 mm Maximale snijdikte in plaat: 20 mm Bladlengte: 455 mm 90°-snede: 130 x 130 x 13 mm 45°-snede: 90 x 90 x 10 mm Op maat gesneden rond/vierkant: 45 mm Elektromotor (vermogen): 7,5 kW Lengte: 1800 mm Diepte: 1200 mm Hoogte: 2000 mm Gewicht: 1650 kg
Hot stamping hand lever press, embossing foils, silver gloss and gold luster among others are included Note: The operating hours are unknown. The entry 99999 hours is only pro forma and does not correspond to the actual hours
Height=0.92 m, Overall length= 0.6 m, Overall width= 1.22 m, Net weight= 170 kg,
Press capacity: 63 ton Ram stroke adjustable: 8 - 60 mm Slide adjustment: 80 mm Shut height (stroke down, adjustment up): 300 mm Table surface area : 810 x 550 mm Slide area: 700 x 420 mm Hole in table: 550 x 140 mm Distance between oil tray: 700 mm Table height over floor: 920 mm Number of strokes: 65 - 400 s.p.m. Weight of machine approx.: 8 ton Dimensions L x W x H: 2935 x 1170 x 3000 mm Main Motor: 11 kW
WIKA G 1/2 Analogue Pressure Gauge 10bar Bottom Entry 100mm Outside Diameter
Capacity: 35 ton Throat depth: 225 mm Ram stroke: 8 - 80 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 325 mm Table surface area : 600 x 450 mm Slide area: 300 x 225 mm Number of strokes: 160 s.p.m. Required power: 2,2 kW Dimensions L x W x H: 1000 x 1600 x 2200 mm Weight of machine approx.: 1,9 ton
Thermometer Gauge DK-T-6x12-1/2PT DENKI BIMETAL THERMOMETER MODEL: DK-6x12-1/2PT(0-200C) RANGE: 0-200C/F DIAL SIZE:6", STEMLENGTH: 12"
Manufacturer: Rabolini Model: Imperia Type of Machine : Die–cutting press Find more here - / Contact us at -
Capacity: 4517l, operating pressure at 20°C: 3atü. An on-site inspection is possible. Can be used for liquids.
The Dorst TPA 50/4 is a reliable, used mechanical powder compaction press designed for precision and efficiency. Offering a robust maximum pressing force of 500 kN and a maximum withdrawal force of 400 kN, it supports a variety of powder compaction tasks. With a filling height up to 180 mm and a pressing stroke of up to 90 mm, this machine is adaptable to diverse requirements. Equipped with an upper punch stroke of 120 mm and an adjustable travel of 220 mm, the Dorst TPA 50/4 provides flexibility for different applications. It operates at a speed of 7 to 32 strokes per minute, ensuring efficient production. The press requires a compressed air supply, consuming approximately 200 liters per minute, with a total connected load of around 18 kW. Constructed with durability in mind, the press measures approximately 2000 mm in width, 1700 mm in depth, and 3250 mm in height, and weighs around 5, ...
The Dorst TPA 50/2 is a used mechanical powder compaction press engineered for precision and efficiency, making it suitable for demanding industry applications. With a maximum pressing force of 500 kN and a maximum withdrawal force of 400 kN, this machine is robust and reliable. This model press allows you a maximum filling height of 180 mm and a pressing travel of up to 90 mm. Designed for versatility, it features an upper punch stroke of 120 mm and an adjustable travel of 220 mm, operating at speeds ranging from 7 to 32 strokes per minute. It requires a compressed air supply with an intake of approximately 200 liters per minute and has a total connected load of around 18 kW. The construction is sturdy and occupies a footprint with dimensions of approximately 2000 mm in width, 1700 mm in depth, and 3250 mm in height, weighing approximately 5,500 kg. The press operates at a workplace-rel ...
The Dorst TPA 5 is a refurbished mechanical powder compaction press, designed for precision and efficiency in industrial applications. It offers powerful performance with a maximum pressing force of 50 kN and a withdrawal force of up to 40 kN. This makes it suitable for a variety of powder compaction tasks, with a filling height of 50 mm and pressing travel capability of 25 mm. This machine provides flexibility with an upper punch stroke of 85 mm and an adjustable travel span of 70 mm, operating at 6 to 30 strokes per minute. It consumes around 50 liters of compressed air per minute and has a total electrical load of approximately 4.00 kW. With durable construction, the Dorst TPA 5 maintains a quiet operation at a sound level of 70 dB(A). The presss compact dimensions, approximately 1200 mm in both width and depth and a height of 2150 mm, with a weight of about 1,200 kg, make it a manage ...
Punching force: 500kN, throat depth: 610mm, stroke: 60mm, max. hole diameter in steel thicknesses 15mm/9mm/4.5mm: 30mm/50mm/100mm, max. material thickness: 15mm. Machine dimensions X/Y/Z: approx. 1100mm/1550mm/1750mm, weight: approx. 1650kg. An on-site inspection is possible.
Punching width: 500mm, rated current: 20A, control voltage: 220V, weight: 2.5t. No defects known, regularly maintained, operating hours unknown. With punching tools and punching blade, only little documentation available. An on-site inspection is possible.
pressure: 80.0 t stroke: 250 mm table surface area: 1040 x 260 mm column travel between the guideways: 1040 mm ajustment speed: 8.0 mm/sec working feed: 5.0 mm/sec return speed: 10.0 mm/sec engine output: 5.5 kW weight of the machine ca.: 835 kg. dimensions of the machine ca.: 1810 x 700 x 2100 mm Furnishing: - Robust electro-hydraulic workshop press, with fixed cylinder - Ideal for aligning axles, shafts, etc., but also for pressing in and out of bolts, bearings, bushings and much more. - Robust welded steel construction for high demands - Table height adjustment via piston rod including round steel chain and 2x locking bolts Piston rod with metric socket - 1x set of V-block prism supports - Manometer for pressure display - simply constructed hand control with: 1x delivery speed 1x working speed 1x retreat speed - Piston can be stopped in any position - Hydraulic tank mounted on t ...
pressure: 20 t throat: 200 mm stroke: 0 - 50 mm table:: 360 x 550 mm table:: 140 mm - Bohrung no. of strokes: 160 Hub/min bore: 35,0 mm - Werkzeug compressed air: max. 6,0 bar dayligth: 240 mm total power requirement: 2,2 kW weight: 1.250 kg range L-W-H: 1310 x 1250 x 1860 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 30 t throat: 200 mm stroke: 0 - 60 mm table:: 400 x 600 mm table:: 150 mm - Bohrung no. of strokes: 140 Hub/min bore: 40,0 mm - Werkzeug compressed air: max. 6,0 bar dayligth: 300 mm total power requirement: 3,0 kW weight: 1.670 kg range L-W-H: 1150 x 1350 x 2050 mm Furnishing: - Welded steel structure body frame - AISI 4140 (42CrMo4) alloy steel crankshaft - CNC ground for maximum precision SnBz-12 quality - Bronze bearings, ground for minimal surface resistance - 4 sides pneumatic clutch-brake combination - PLC control for safety (PILZ Germany) - Photo cell light barriers around the work table (PILZ Germany) - Two-hand and foot pedal control - Adjustable stroke - Central lubrication system - CE safety approval by TÜV - electrical equipment SIEMENS, SCHNEIDER, PHOENIX, OMRON The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 10 t throat: 160 mm stroke: 0 - 40 mm table:: 270 x 370 mm table:: 100 mm - Bohrung no. of strokes: 200 Hub/min bore: 25,0 mm - Werkzeug compressed air: max. 6,0 bar dayligth: 180 mm total power requirement: 0,75 kW weight: 590 kg range L-W-H: 1.168 x 1.010 x 1.670 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 20,0 t stroke: 185 mm table surface area: 170 mm Breite column travel between the guideways: 510 mm weight of the machine ca.: 112 kg dimensions of the machine ca.: 1630 x 560 x 730 mm Furnishing: - Standard with pressure cylinder that can be moved to the left and right - For aligning, pressing, bending, assembling gears, discs, etc. - Standard with foot pedal and hydraulic hand pump for piston delivery - Standard with support prism for aligning shafts - With automatic piston retraction by integrated return spring as standard - Height-adjustable press table with locking bolts - Large manometer for reading the compressive force - Including two-stage hydraulic pump - Robust construction with welded steel frame The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 30 t stroke: 150 mm table surface area: 185 mm Breite column travel between the guideways: 530 mm weight of the machine ca.: 162 kg dimensions of the machine ca.: 800 x 700 x 1805 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 50 t stroke: 200 mm table surface area: 730 x 205 mm dayligth: 1050 mm column travel between the guideways: 730 mm weight of the machine ca.: 288 kg. Description : - Standard with cable winch - for easy height adjustment of the support table - Piston delivery either manually or pneumatically - Powerful workshop presses for craft and repair businesses - Optimum price-performance ratio thanks to rational design - The standard foot pedal keeps your hands free for the workpiece - Increased range of application thanks to the optionally . available pressure mandrel set (10 pieces). - Pressure cylinder with integrated return spring for piston return - Welded steel frame for heavy use and high stability - Versatile in use thanks to the pressure cylinder that can . be moved to the left and right The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 1000 kg throat: 95.0 mm table length: 120 mm table width: 120 mm total power requirement: manuell kW weight of the machine ca.: 17.0 kg dimensions of the machine ca.: 270 x 130 x 330 mm Description: - For pressing in and out bearings, bushings, etc. - Made of torsion-resistant steel - Includes mounting holes, ideal for mounting on a workbench - Suitable for bushing removal, straightening, bending, reaming, etc. - Adjustable lever bar, depending on the required force - Ideal for repair shops and general workshop use The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 5,0 t throat: 215 mm workpiece height max.: 445 mm Mandrel diameter: 50 x 50 x 645 mm table plate: Ø 275 mm total power requirement: manuell kW weight of the machine ca.: 160 kg. dimensions of the machine ca.: 370 x 550 x 810 mm Description : - for pressing in and out of bearings, bushings, ... - the basic body of the model DP 5 made of high-quality gray cast iron - Includes mounting holes, ideal for mounting on a workbench - suitable for bushing, straightening, bending, broaching, ... - variably adjustable lever bar, depending on the required effort - ideal for repair shops and the general workshop area The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 175 t chamfer lenght: 4100 mm distance between columns: 3600 mm column arm: 410 mm ram stroke speed: 180 mm/sec return speed: 135 mm/sec work speed: 10,0 mm/sec work stroke: 275 mm dayligth: 550 mm table height: 900 mm table width: 90,0 mm oil volume: 200 ltr. voltage: 400 Volt total power requirement: 15,0 kW weight: 11.950 kg range L-W-H: 5100 x 2150 x 2850 mm -------------------------------------------------- Press brake with special equipment increased installation height increased cylinder stroke as well as increased bending beam speeds -------------------------------------------------- Furnishing: - DELEM CNC control model DA-58T graphics / touchscreen 2D graphic programming 15 high definition color TFT screen Bending sequence calculation Product programming and display in real size USB interface - Motorized backgauge with R-axis, on recirculating ball spindles - ...
pressure: 100 t chamfer lenght: 2600 mm distance between columns: 2200 mm column arm: 410 mm ram stroke speed: 200 mm/sec work speed: 9.5 mm/sec return speed: 155 mm/sec work stroke: 275 mm dayligth: 530 mm table height: 900 mm table width: 90.0 mm oil volume: 150 ltr. voltage: 400 Volt total power requirement: 7.5 kW weight: 6850 kg range L-W-H: 3750 x 1950 x 2800 mm -------------------------------------------------- Press brake with special equipment increased installation height increased cylinder stroke as well as increased bending beam speeds -------------------------------------------------- Furnishing: - DELEM CNC control model DA 53T (touchscreen) - Motorized backgauge with R-axis, on recirculating ball spindles - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by CNC - Upper deer foot tool with PS 135.8 ...
pressure: 220 t chamfer lenght: 3100 mm distance between columns: 2600 mm column arm: 410 mm ram stroke speed: 180 mm/sec work speed: 10.0 mm/sec return speed: 185 mm/sec work stroke: 275 mm dayligth: 550 mm table height: 930 mm table width: 200 mm oil volume: 300 ltr. voltage: 400 Volt total power requirement: 18.5 kW weight: 11286 kg Dimensions (HxWxD): 4550 x 2250 x 2850 mm -------------------------------------------------- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection -------------------------------------------------- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z2 - split upper deer foot ...
pressure: 220 t chamfer lenght: 4100 mm distance between columns: 3600 mm column arm: 410 mm ram stroke speed: 180 mm/sec work speed: 10.0 mm/sec return speed: 185 mm/sec work stroke: 275 mm dayligth: 550 mm table height: 900 mm table width: 160 mm back stop - adjustable: max. 800 mm oil volume: 300 ltr. voltage: 400 Volt total power requirement: 18.5 kW weight: 14000 kg range L-W-H: 5150 x 2250 x 3000 mm -------------------------------------------------- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection -------------------------------------------------- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 ...
pressure: 220 t chamfer lenght: 3760 mm distance between columns: 3250 mm column arm: 410 mm ram stroke speed: 180 mm/sec work speed: 10.0 mm/sec return speed: 160 mm/sec work stroke: 275 mm dayligth: 550 mm table height: 900 mm table width: 160 mm oil volume: 300 ltr. voltage: 400 Volt total power requirement: 18.5 kW weight: 12906 kg range L-W-H: 5100 x 2250 x 2900 mm -------------------------------------------------- Press brake with special equipment increased installation height increased cylinder stroke as well as increased bending beam speeds -------------------------------------------------- Furnishing: - DELEM CNC control model DA 58T (TouchScreen) - Motorized backgauge with R-axis, on recirculating ball spindles - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by CNC - Upper deer foot tool with PS 135 ...
pressure: 320 t chamfer lenght: 3100 mm distance between columns: 2600 mm column arm: 410 mm ram stroke speed: 140 mm/sec work speed: 10.5 mm/sec return speed: 150 mm/sec work stroke: 375 mm dayligth: 650 mm table height: 900 mm table width: 240 mm oil volume: 400 ltr. voltage: 400 Volt total power requirement: 30.0 kW weight: 17082 kg Dimensions (HxWxD): 4550 x 2450 x 3200 mm -------------------------------------------------- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection -------------------------------------------------- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z2 - split upper deer foot ...
pressure: 40.0 t chamfer lenght: 1270 mm distance between columns: 1050 mm column arm: 350 mm dayligth: 387 mm work stroke: 170 mm table height: 850 mm back stop - adjustable: 800 mm adjustment speed: 230 mm/min ajustment speed: 140 mm/sec working feed: 10.0 mm/sec return speed: 170 mm/sec total power requirement: 5.5 kW weight of the machine ca.: 3220 kg dimensions of the machine ca.: 2150 x 1650 x 2300 mm -------------------------------------------------- Press brake with special equipment increased installation height increased cylinder stroke as well as increased bending beam speeds -------------------------------------------------- Furnishing: - DELEM CNC control model DA 58T (TouchScreen) - Motorized backgauge with R-axis, on recirculating ball spindles - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by C ...
pressure: 160 t chamfer lenght: 3100 mm distance between columns: 2600 mm column arm: 250 mm ram stroke speed: 90.0 mm/sec work speed: 7.5 mm/sec return speed: 80.0 mm/sec work stroke: 160 mm dayligth: 395 mm table height: 900 mm back stop - adjustable: max. 800 mm oil volume: 200 ltr. voltage: 400 Volt total power requirement: 11.0 kW weight: 7524 kg range L-W-H: 4250 x 1900 x 2550 mm Furnishing: - DELEM CNC control model DA-66T graphic/touch screen 2D graphical programming 17 TFT color screen with high resolution Bending sequence calculation Product programming and real size display USB interface intuitive, graphical entry of profiles Automatic calculation of features: tool safety zones, Press force, bending tolerance, crown setting, stretched Length, embossing force, flattening, automatic rounding calculation Radius programming Graphic tool and product library Collision mo ...
pressure: 80.0 t chamfer lenght: 2600 mm distance between columns: 2200 mm column arm: 250 mm ram stroke speed: 90.0 mm/sec work speed: 7.5 mm/min return speed: 60.0 mm/sec work stroke: 160 mm dayligth: 380 mm table height: 900 mm oil volume: 150 ltr. voltage: 400 Volt weight: 5227 kg range L-W-H: 3750 x 1950 x 2400 mm Furnishing: - DELEM - CNC control model DA-58T - controlled axes: Y1 - Y2 and X - AKAS laser in front of the machine - manual crowning - Upper tool, deer foot - Lower tool, die block with 4Vs - SICK light barrier behind the machine - 2 front support arms - SIEMENS - electrical system - BOSCH / HOERBIGER hydraulic system - CE mark / declaration of conformity - Operating manual: machine and control - Safety manual: press brakes The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 160 t chamfer lenght: 3760 mm distance between columns: 3250 mm column arm: 250 mm ram stroke speed: 90.0 mm/sec work speed: 7.5 mm/min return speed: 80.0 mm/sec work stroke: 160 mm dayligth: 395 mm table height: 900 mm oil volume: 200 ltr. voltage: 400 Volt weight: 8514 kg range L-W-H: 4910 x 1900 x 2550 mm Furnishing: - DELEM - CNC control model DA-58T - controlled axes: Y1 - Y2 and X - SICK light barrier in front of the machine - Upper tool, deer foot - Lower tool, die block with 4Vs - manual table crowning - SICK light barrier behind the machine - 2 front support arms - SIEMENS - electrical system - BOSCH / HOERBIGER hydraulic system - CE mark / declaration of conformity - Operating manual: machine and control - Safety manual: press brakes The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 175 t chamfer lenght: 3100 mm distance between columns: 2600 mm column arm: 410 mm ram stroke speed: 180 mm/sec work speed: 10.0 mm/sec return speed: 135 mm/sec work stroke: 275 mm dayligth: 550 mm table height: 900 mm table width: 90.0 mm oil volume: 200 ltr. voltage: 400 Volt total power requirement: 15.0 kW weight: 9450 kg range L-W-H: 4250 x 2150 x 2800 mm -------------------------------------------------- Press brake with special equipment increased installation height increased cylinder stroke as well as increased bending beam speeds -------------------------------------------------- Furnishing: - DELEM CNC control model DA-58T graphic/touch screen 2D graphical programming 15 TFT color screen with high resolution Bending sequence calculation Product programming and real size display USB interface - Motorized backgauge with R-axis, on ball screws - X = 800 mm R = ...
pressure: 150 t stroke: 300 mm table surface area: 1070 x 290 mm column travel between the guideways: 1070 mm ajustment speed: 9.0 mm/sec working feed: 5.0 mm/sec return speed: 10.0 mm/sec engine output: 11.0 kW weight of the machine ca.: 1870 kg. range L-W-H: 2200 x 1300 x 2300 mm Exhibition machine from 2021 with only approximately 2 operating hours Condition as new Special price upon request Features: - Robust electro-hydraulic workshop press with fixed cylinder - Ideal for aligning axles, shafts, etc., but also for pressing in . and out bolts, bearings, bushings, and much more. - Robust welded steel construction for heavy-duty use - Table height adjustment via piston rod Includes round steel chain and 2 locking pins Piston rod with metric mount - 1 set of V-block prism supports - Pressure gauge for pressure display - Simple manual control with: 1 feed speed 1 working speed 1 ...
pressure: 60.0 t chamfer lenght: 2100 mm distance between columns: 1700 mm column arm: 410 mm ram stroke speed: 160 mm/sec work speed: 10.0 mm/sec return speed: 165 mm/sec work stroke: 275 mm dayligth: 530 mm table height: 900 mm table width: 90.0 mm oil volume: 150 ltr. voltage: 400 Volt total power requirement: 7.5 kW weight: 5640 kg range L-W-H: 3250 x 1960 x 2750 mm -------------------------------------------------- Press brake with special equipment increased installation height increased cylinder stroke as well as increased bending beam speeds -------------------------------------------------- Furnishing: - DELEM CNC control model DA 53T (touchscreen) - Motorized backgauge with R-axis, on recirculating ball spindles - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by CNC - Upper deer foot tool with PS 135 ...
pressure: 220 t chamfer lenght: 4100 mm distance between columns: 3600 mm column arm: 410 mm ram stroke speed: 180 mm/sec work speed: 10.0 mm/sec return speed: 160 mm/sec work stroke: 275 mm dayligth: 550 mm table height: 900 mm table width: 160 mm oil volume: 300 ltr. voltage: 400 Volt total power requirement: 18.5 kW weight: 13800 kg range L-W-H: 5150 x 2250 x 3000 mm -------------------------------------------------- Press brake with special equipment increased installation height increased cylinder stroke as well as increased bending beam speeds -------------------------------------------------- Furnishing: - DELEM CNC control model DA-58T graphics / touchscreen 2D graphic programming 15 high definition color TFT screen Bending sequence calculation Product programming and display in real size USB interface - Motorized backgauge with R-axis, on recirculating ball spindles - X ...
pressure: 320 t chamfer lenght: 4100 mm distance between columns: 3600 mm column arm: 410 mm ram stroke speed: 140 mm/sec work speed: 10.5 mm/sec return speed: 150 mm/sec work stroke: 375 mm dayligth: 650 mm table height: 900 mm table width: 220 mm oil volume: 400 ltr. voltage: 400 Volt total power requirement: 30.0 kW weight: 22064 kg Dimensions (HxWxD): 5350 x 2450 x 3150 mm -------------------------------------------------- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection -------------------------------------------------- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z2 - split upper deer foot ...
Inv. Num. : 8643 Type: LEK 250 Producer: ZTS Generated: GO Parameters: Compressive force: 250 t
Briquetting press type GP 120 Tandem Briquetting press for briquetting chips, wood chips and dusts incl. autom. Level detector - Briquette diameter: 60 mm - Pressing capacity: 40 - 120 kg/h 2 = 80 - 240 kg/h (depending on material) - Hopper opening: approx. 1,900 x 1,900 mm - Hopper height: approx. 1,800 mm - Hopper capacity: approx. 6.0 m³ - Drive power: 7.5 kW, 400 V, 50 Hz - Control cabinet: available on both sides - Operating hours: 13,725 h or 13,005 h - Hydraulic power unit: approx. 300 l tank for hydraulic oil - Weight: approx. 1,100 kg 2 = 2,200 kg Used briquetting press in good condition W-pliers cylinder, pliers (RB 120 reinforced), pliers connection flange renewed on one side (left in the direction of conveyance) briquetting | Briquette Press | Briquetting Presses | Briquette Press | Briquetting # Briquetting press type GP 120 Tandem Briquetting ...
Machine name: Chamber filter press used Manufacturer: Simex Sauer Type: SPK 80 Year of Make: 2000 Design: Side-spar press Filter pressure: 16 bar Press capacity: approx. 1,000 litres Procedure: Closed Filter area: Approx. 80 m2 Plate format: 800 x 800 mm Number of plates: 78 Panel material: Polypropylene Plate Feed: Manual Filter Cloths: No Filter Cloth Washer: No Panel package length: 4,400 mm Cake thickness: 25 mm Closing pressure: 350 bar Dimensions: L 6,400 x W 1,400 x H 1,500 mm Curb weight: 6,000 kg Technical documentation: No Accessories: A control cabinet & a hydraulic system Condition: Used Price: On request
maximum number of results exceeded
please refine your search
