pre heater used for sale

Manufacturer: Comil, Bauyeshr : 1995, Hydraulical/pneumatical: hydraulisch, High / low pressure: yes, Press length mm: 2200, Press hight mm: 60, Press depth mm: 650, Cylinder vertically: 4, Zylinder horizontal: 4, Pre-assembling conveyor: yes, Clamping: yes, Machine rigging: automatisch, Compressed air bar: 6, Year :1996

Eccentric shaft by drawing K04.038.842-22-402 for hot stamping press K04.038.842 (K8542), 1600T brand new in state stale from stock W 4675 kg

Manufacturer: Hess, Type: Kantenbügelpresse, Year: ca.1990, Pre-warming of massive edges and heating rod: 2, Working length mm: 4000, Working widht mm: 60, Carriage: yes, Tiltable design: yes, Pneumatik: yes, Cylinder: 8, Wight approx. kg: 300, Year :ca.1990

GRP 250to year 2000 Needle bearing to screw shaft defective, machine stopped. Find more here - / Contact us at -

Pressing and joint-setting machine Book height : 100 - 520 mm Book width : 120 - 450 mm Book thickness : 6.5 - 100 mm Output : approx. 150 books/hour (depending on the material used)

Offer 25100 Specifications: - Pressure capacity 200 t - Working width 3050 mm - Passage between the uprights 2550 mm - Table width 180 mm - Projection 250 mm - Installation height 400 mm - Feed speed 80 mm/sec. - Working speed 6.7 mm/sec. - Retraction speed 67 mm/sec. - Plunger stroke 150 mm - Adjustment range fixed stops 120 mm - Drive 400 V 14.5 kW - Space requirement approx. W 3800 x H 2980 x D 1700 mm - Weight approx. 11500 kg - with: - Back gauge with 2 stop fingers - Deer's foot tool - 4-fold universal die - Two-hand control panel, foot switch,

Inv. Num. : 8332 Type: TrumaBend V50 Producer: Trumpf Generated: Parameters: Compressive force: 85 t Maximum bending length: 1275 mm Distance between frame walls: 1040 mm Machine height: 2375 mm Machine length: 1930 mm Machine width: 2030 mm Machine weight: 4750 kg

Pressing force: 2000kN, max. installation height: 550mm, total power requirement: 72kW, operating pressure: 210bar. Including feed unit. On-site inspection is possible.

Manufacturer: NEFF Model: 4SP 160 Year of Manufacture: 2011 Operating Hours: 25 aprox Type of Machine: Hydraulic Press Weight: 7000 kg Condition: Used Control System: Siemens S7 (PLC) Technical Specifications - Press Force: 1600 kN (adjustable from 160–1600 kN) - Return Force: Approx. 160 kN - Stroke (Hub): 500 mm - Table Size (W x D): 2000 x 800 mm - Ram Size (W x D): 2000 x 800 mm - Clear Height (Ram Up): 700 mm - Max. Daylight (Open Height): 2850 mm - Table Height Above Floor: 800 mm - Clearance Between Columns (W x D): 1600 x 410 mm - Installation Space (W x D x H): 2000 x 800 x 700 mm Electrical System - Operating Voltage: 400V AC - Control Voltage: 24V DC - Valve Voltage: 24V DC - Frequency: 50 Hz - Voltage Fluctuation Tolerance: ±5% - Max. Ambient Temp: 35°C Find more here - / Contact us at -

Ajax 1,000 Ton Straight Side Mechanical Forging Press S/N 4410 10” Stroke 33” Shut Height 36” x 36” Bed 80 Strokes Per Minute Partially Rebuilt Ajax 1,000 Ton Straight Side Mechanical Forging Press S/N 4621 10” Stroke 32” Shut Height 36” x 32” Bed 80 Strokes Per Minute Bolsters are included. Both presses are in working condition and under power.

Offer 24591 Specifications: - Max. pressing force 25 t - Max. ram stroke 500 mm - Lifting speed 0 - 40 mm/s - Return 0 - 200 m/min - Installation height 800 mm - Projection to the middle of the ram 360 mm - Pusher clamping surface 440 x 360 mm - Plunger clamping pin 40 mm - Table size 630 x 500 mm - Table height above floor 710 mm - Thermoforming force 10 t - Largest deep-drawing depth 160 mm - Drive 400 V / 4 kW - Space requirement approx. W 800 x H 2720 x D 1150 mm - Weight approx. 2500 kg

Press force: 160t, stroke adjustment: 20mm-140mm, stroke rate: 10-60 strokes/min, table dimensions X/Y: 1050mm/820mm, opening in table: 300mm/300mm, ram adjustment: 100mm. On-site inspection is possible.

Control SAFAN ... TS 1 Thrust... 50t Bending length ... 2550mm controlled axes ... 4 Drive... Electric Max. ram stroke ... 215mm Main engine power ... 9kW Machine weight ... 5050kg The machine is in good condition, possible to test under power.

Pressing force: 63t, operating pressure: 160bar, pressing speed downwards/upwards: 200mm/400mm/s, ram stroke: 500mm, throat depth: 360mm, max. ram table distance: 800mm, weight: approx. 4200kg. On-site inspection is possible.

Compressive force: 1000kN/100t, ram stroke: 200mm, max. operating pressure: 290bar, control: DNC70, safety distance: 166mm, overtravel time: 104ms, overtravel distance: 7mm.

-) Press surface: 3,100 x 1,600 mm -) Cylinder: 8 cylinders -) Floors: 5 floors, 6 heating plates -) Heating plates: drilled 40mm steel heating plates -) Heating: for hot water or thermal oil (up to 200° -) Press opening: up to 600 mm -) Cooling: with own unit Etc.

An old Künstner & Hampel eccentric press is available. Pressure capacity: 25 tons, power requirement: 2.5 HP. On-site inspection is possible.

Brand Lisec Type Butyl extruder machine Model LBH-25ARS + 2x RAV2 Serial number 572-003937 Year of construction 2000 Weight 2.1ton Assets 7kVA Air pressure 6bar Water pressure: NVT Length +/- 11m Width +/- 5m Height +/- 3.5m Working height ,4m Transport dimensions L x W x H Special 2 pcs 3.5×2.6x2m + 6×1.5×3.2 Min.-max. profile 4-15mm Min.-max glass size 2.5×3 Number of brushes n/a Number of spindles n/a State machine n/a Type of control B&R Electrical connection 380+N+PE Instructions for use Yes Electrical diagram Yes Parts list available on request Available software back up Photos/film available: Photos and video available

A high-performance cold press is available for pre-pressing diamond segments in tools. Main cylinder: 2, cylinder diameter top/bottom: 100mm/100mm, cylinder stroke top/bottom: 180mm/150mm, max. operating pressure: 300bar, press force: 235kN. Die clamping cylinder: 2, piston diameter: 63mm, cylinder stroke: 15mm, max. clamping force: 62kN, max. operating pressure: 200bar, piston area: 31.2cm². Weighing stations: 2, weight range: 1g-50g, accuracy: +/-0.05g, powder hopper volume: 12l. Machine dimensions X/Y/Z: approx. 1800mm/1000mm/1900mm, weight: approx. 2000kg. Documentation available. On-site inspection is possible.

Max. Press force: 1000kN, max. retraction force: 110kN, max. stroke: 360mm, max. working pressure: 251bar, installation height: 560mm, control panel: Siemens SIMATIC OP27, weight: 7.5t, on-site inspection is possible.

Pressure leaf filter for filtration of vegetable oil - 8m² filter area - 720 litres - Pneumatically operated swing flap at the outlet - Including piping with valves - With control cabinet - Optionally with screw compressor

Four Neff single-column presses are available. 1) Neff T 6.3, year of manufacture: 1989, output: 3kW. 2) Neff single-column press, operating hours: 9097h. 3) Neff EP 10 single-column press, year of manufacture: approx. 1950. 4) Neff single-column press. On-site inspection is possible.

Beyeler RH 100 ton x 3100 mm Capacity: 100 ton x 3100 mm Backgauge: manual Passage between uprights: 2630 mm Max stroke: 215 mm Max distance between table -- ram: 410 mm Depth of throat: 255 mm Locking speed: 100 mm/sec Working speed: 6,5 mm/sec Electric motor (power): 5,5 kW Length: 3300 mm Depth: 1550 mm Height: 2450 mm Weight: 7 ton

Max. cutting height: 100mm, saw blade diameter: 250-400mm, bore: 30mm, carriage length: 2600mm, motor power: 5.5kW, length: 3100mm, width: 2400mm, height: 1500mm, weight: 770kg. On-site inspection is possible.

LVD PPBL 200 ton x 4100 mm Capacity: 200 ton x 4100 mm Backgauge: manual Passage between uprights: 3150 mm Max stroke: 150 mm Max distance between table -- ram: 400 mm Depth of throat: 250 mm Table width: 200 mm Locking speed: 100 mm/sec Working speed: 6,5 mm/sec Returning speed: 65 mm/sec Electric motor (power): 11 kW Weight: 13,4 ton

Working dimensions X/Y: 3000mm/2000mm, cylinder stroke: 1000mm, height adjustment: 2000mm-2600mm, length adjustment: 3000mm-6000mm, pressing force: 2t, space requirement: 4100mm/1000mm/2450mm, weight: approx. 1500kg. Documentation available. On-site inspection is possible.

Maplan 250ton Injection Machine Injection MTF 1500/250 Platen size = 630mm x500mm Stripper plate/ejectors =top only Max gap between platens = 702mm Volume = 1500 ccm3 Tonnage = 250T Year 2007

FETTE Terminal Data Control Type 2080 Year 1989

FETTE Data Control 2 Installed in a mobile cabinet including an EPSON printer

Maplan 160ton Injection Machine Injection MTF 750/160 Platen size = 510mm x 450mm Stripper plate/ejectors =top only Max gap between platens = 575mm Volume = 750 ccm3 Tonnage = 160T Year 2002

Eillert washer for sinking products

Press capacity: 50 ton Ram stroke: 54 mm Slide adjustment: 80 mm Shut height (stroke down, adjustment up): 303 mm Table surface area : 810 x 550 mm Number of strokes: 65 - 400 s.p.m. Weight of machine approx.: 7,5 ton Main Motor: 11 kW

Used pastry machine CANOL, type: CA-L -in bakery condition- - Dough preparation CA-L (built in 2001) - Calibration unit TS/0 (built in 2002) -Longitudinal section -Guillotine - Incl. many cutting tools (cutting rollers) - incl. band C/L (built in 2001) The system was still in use until recently and works without any problems. Visits and test runs are possible by arrangement.

Key data: 80 t, 400 mm, 112 mm

Printing capacity: 80 ton Table surface: 750 x 550 mm Plunger adjustment: 80 mm Stroke length: 8 - 112 mm Stroke rate: 78 p/min. Projection: 400 mm Equipped with: - Air coupling - Safety screen Country of origin: Germany Motor power: Machine LxWxH: 2000 x 1200 x 2900 mm Machine weight approx.: 7000 kg

A dismantled Mecamaq hydraulic press is available. Pressing force: 100t, max. pressure: 290bar, main piston diameter: 200mm/120mm, auxiliary cylinder diameter: 40mm/25mm. Main cylinder working stroke: 500mm, max. installation height: 800mm, working height: 800mm, effective dimensions X/Y: 700mm/500mm, table dimensions X/Y: 800mm/500mm, working speed: 6mm/s, return speed: 150mm/s. Max. tool dimensions X/Y: 800mm/600mm, max. tool weight: 1000kg. Machine dimensions X/Y/Z: approx. 1000mm/1350mm/2750mm, weight: approx. 4000kg. Documentation available. On-site inspection is possible.

Key data: 110 t, 3100 mm, 2550 mm

Printing capacity: 110 ton Bending length: 3,100 mm Stand width: 2,550 mm Back gauge: 1,500 mm Stroke length: 150 mm Projection: 250 mm Feed speed: 100 mm/sec. Working speed: 8 mm/sec. Retraction speed: 65 mm/sec. Control: ESA Kvara S630 Touch Equipped with: - Foot pedal - Various tool sets - Light curtain safety Merlino - Controls renewed in 2018 Country of origin: Netherlands Motor power: 7.5 kW Machine LxWxH: 320 x 160 x 244 cm Machine weight: 8,700 kg

Key data: 300 t, 4300 mm, 3700 mm

Printing capacity: 300 ton Bending length: 4,300 mm Stand width: 3,700 mm Back gauge: 550 mm Stroke length: 300 mm Projection: 450 mm Feed speed: 120 mm/sec. Working speed: 10 mm/sec. Retraction speed: 120 mm/sec. Control: Delem DA65 Equipped with: - Y1, Y2, X&R - Axis Controlled - CNC hydraulic crowning - Various sets of bending tools - Safety light cabinet Lazer Safe - Operating instructions and machine documents Country of origin: Netherlands Motor power: 30 kW Machine LxWxH: 510 x 200 x 330 cm Machine weight: 21,500 kg

HYDRAULIC PRESS with hot platens model ITALPRESSE SCF 6 second hand machine for wood, veneer, composite materials, furniture, panels etc platen useful size mm.3000 x 1300 n.06 cylinders diam.mm.70 max. thrust Ton. 120 opening mm. 400 hydraulic pump motor power Hp 3 hot water plates heating via wood boiler weight kgs. 4500 volt. 380/50

fabric-no.: 202 395 working length: 2550 mm output: 2000 KN tracking travel: 13 mm safety distance: 176 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Manufacturer: Feintool Model: GKP-F 160 Type of Machine : Fineblanking Press Revision Year: 2003 Total Force: 1600 kN Head Pressure: 10 - 400 kN Table Pressure: 10 - 500 kN Stroke Rate: 20 - 70 strokes per minute Operating Voltage: 3x400V, 50Hz, N + PE Control Voltage: 24V Power: 22 kW year 1975 but had was completely refurbished in 2000 Find more here - / Contact us at -

pressure: 63 t distance between columns: 650 mm stroke: 200 mm total power requirement: 30 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Manufacturer: Feintool Model: GKP-F 160 Type of Machine : Fineblanking Press Revision Year: 2003 Total Force: 1600 kN Head Pressure: 10 - 400 kN Table Pressure: 10 - 500 kN Stroke Rate: 20 - 70 strokes per minute Operating Voltage: 3x400V, 50Hz, N + PE Control Voltage: 24V Power: 22 kW Fully refurbished in year 2003 Find more here - / Contact us at -

pressure: 500 t passage width: 750 mm stroke: 120 mm total power requirement: 57 kW weight of the machine ca.: 16 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

! Exhibition Machine Corresponds to the Panhans LLB116 with the following optional accessories: - Single-lever operation with fine locking - Dial gauge in the handwheel for height adjustment SPECIFICATIONS: - Max. drilling depth 145 mm - Max. elongated hole length 240 mm - Height adjustment 135 mm - Motor power 1.3/1.7 kW - Suction nozzle Ø 100 mm - Machine weight 200 kg

! Exhibition Machine Equipment/Technical Data Work table mm 800x400 Motor kW 1.5/1.9 kW Spindle speed rpm 1440 / 2880 Max. slotted hole height above the table mm 160 Max. longitudinal work run mm 345 Max. transverse work run mm 245 Spindle stroke mm 160 Clamping Ø of tool mm 0 - 20 Max. tool length mm 175 Span Center Piece 2 Rotating table ° +/- 45° Dimensions of the machine mm 1500x1100x950 Machine weight kg 345 Other features: - Mechanical dowel device, distance 16-22-25-32 - Mechanically numerical spindle height display - Suction nozzle

LVD PPS-TS 100 ton x 3100 mm CNC Capacity: 100 ton x 3100 mm Backgauge: CNC Control: Cadman Express Passage between uprights: 2550 mm Max stroke: 150 mm Max distance between table -- ram: 350 mm Depth of throat: 250 mm Locking speed: 100 mm/sec Working speed: 10 mm/sec Returning speed: 80 mm/sec Electric motor (power): 16 kW

pressure: 75 t throat: 280 mm stroke: 303 mm total power requirement: 15 kW weight of the machine ca.: 7000 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Pneumatic laboratory heating press REITZ PHP3 – used demonstration machine Pressed press 3 KN (0.3 tons) With heating device up to 250 °C and temperature control - Press force 3 KN (0.3 to) - Pneumatic cylinder make Festo - Pneumatic two-hand control - Press plate guided in 4 guide columns - Working surface between guide columns 200 220 mm - Heating and insulating plate 150 x 250 mm -Temperature - Machine table made of aluminum profiles and PA plate 60060060mm - Total weight approx. 100 kg - Mobile with 4 swivel castors, 2 of which with brakes . Suitable for foil pressing and embossing under heat.

Key data: 50 t, 1600 mm, 200 mm

CNC Press Brake COLLY 502/A Numerical Command: CYBELEC type DNC 32 P-CM Capacity: Maxi length 2000 mm x 50 T Throat depth: 200 mm Distance between uprights: 1600 mm Back Gear Gauge 1 axe Defective cylinder Right cylinder joint to change Machine functional (only right cylinder joint to change) Voltage: 380 V Length: 2500 mm Depth: 2100 mm Total height: 2400 mm Weight: approx 4 T

Wheel diameter: 680 mm sawblade length: 8550 mm Sawblade width max.: 1,3 mm Cutting height: mm Motor output: 20 kW Table dimensions: 600 x 620 mm Feed speed: m/min. Machine height: mm Weight: 10.000 kg Bandsaw horizontal, Precision-Saw for Silicon (Solar industry) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.