138,021 used machines on RESALE, but how to find them? Machine Search
Rotary lobe blowers / Roots blowers without drive or attachments from Aerzen.
Power supply, power converter, power supply unit, switching power supply, DIN rail power supply -Manufacturer: Phoenix Contact, power supply -Type: TRIO-PS/1AC/24DC/2.5 Ord.No.: 2866268 -Input: AC 100-240V -Output: 24 V -Dimensions: 125/35/H130 mm -Weight: 0.5 kg
Fuel: natural gas (NG), engine: HMG, space heating unit with CHP: yes, condensing boiler: no, additional heating unit: no, low-temperature boiler: no, B11 boiler: no, combi unit: no. Rated heat input P: 88kW, annual efficiency of the space heating system η: 136%, energy efficiency class: A, usable heat output at rated heat input with additional heater switched off/on: 87.9kW, thermal efficiency at rated heat input with additional heater switched off/on: 57.5%, electrical efficiency at the heat output of the space heating unit with CHP with additional heater switched off/on: 33.5%, auxiliary power consumption at full load/part load el: 1.132kW, in standby mode P SB: 0.06kW, standby heat loss P stby: 0.442kW, annual energy consumption Q HE: 1345kWh, sound power level indoors L WA: 72dB, operating hours: 42,892h. Water was detected in the oil circuit, the unit has an oil-related fault desp ...
2x Fug Low Voltage Power Supply NLN 15000M - 1500 NLN Series (Low Voltage Linear Regulated Power Supplies) Power class 15000W Rated Voltage 1500V The voltage is internally limited to 1500V and cannot be regulated. Technical data -Power connection 400V ±10% 3phase 47-63Hz N-connection and PE (protective earth) always required! Overvoltage category II according to IEC664. Power plug according to IEC309 -EMC EN 50 081 - 2 EN 50 082 - 2 Signal and control cables ≤ 3m length -Security the devices comply with EN 61010 (cf. VDE 0411) -Environmental conditions Operating rooms : for indoor use only (see section 2.1.) Temperature : 0 °C to 40 °C Humidity : maximum relative humidity 80% up to 31 ºC, linearly decreasing up to 50% relative humidity at 40 ºC Pressure : Altitude up to 2000 m above sea level Degree of contamination : 2 according to IEC664 -Degree of protection - IP20 ...
Key data: 250 KW
MAN gas engine is available with very low hours. Type: E2842E312 Scope of supply: CHP Gas line Control Panel Exhaust gas cooler Enclosed silenced container
PRESS DESIGN drive system: eccentric / crank PRESS FORCES total force (nominal): 80 to PRESS TABLE table surface (left-right): 850 mm table surface (front-back): 550 mm SLIDE table surface (left-right): 560 mm table surface (front-back): 376 mm spigot hole diameter: 50 mm stroke: 110 mm stroke rate (max.): 60 /min SLIDE (MECHAN. PRESS) slide adjustment: 80 mm stroke min.: 0 mm stroke max.: 110 mm TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 360 mm DIMENSIONS / WEIGHTS space requirements -left/right-: 855 mm space requirements -front/back-: 1635 mm total height: 2640 mm total weight approx.: 5400 kg ATTACHMENTS (PRESSES) 2-hand engagement: yes foot engagement: optional European CE standards: yes
Title: Ford 7840 Powerstar SLE 4WD Farm Tractor General specifications: Brand: Ford Model: 7840 Version: Powerstar SLE Vehicle type: agricultural tractor Fuel: diesel Drive: four-wheel drive (4WD) Closed cab Color: blue Maximum speed according to cab designation: 40 km/h Engine: Ford GA 401 CID Engine 6-cylinder diesel engine Engine without turbo Displacement: approx. 6,585 cc Rated output: 74 kW / approx. 101 hp Maximum torque: approx. 378 Nm at 1,197 rpm Liquid-cooled Fuel tank: approx. 227 litres Transmission: SLE transmission 16 forward and 16 reverse gears Four-stage powershift/load shift Synchronized group switching Synchronized reversing Electro-hydraulically operated all-wheel drive Electro-hydraulic differential lock Hydraulics and Linkage: Three-point rear linkage, category 2 Electronically controlled rear linkage Top link Height-adjustable towbar Four double-acting hyd ...
Consisting of: 3x grinder 1x circular saw machine 1x dremel Auction-ID: A1-44050-258
CONTROLS conventional PRESS DESIGN drive system: eccentric / crank frame design: C-frame, single sided PRESS FORCES total force (nominal): 100 to SLIDE slide force: 100 to stroke rate (max.): 72 /min SLIDE (MECHAN. PRESS) slide adjustment: 80 mm stroke adjustment: yes stroke min.: 8 mm stroke max.: 112 mm TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 407 mm ATTACHMENTS (PRESSES) 2-hand engagement: yes for safe tools only
Key data: 264 KW, 450 kVA, 400 V
Jenbacher Gas-CHP J 208 GS-C Gas electricity and heat generator from 1994 with 67,000 operating hours, CHP unit with control and silencer, additional parts. 1 available 253 KWel x 1,500 rpm, 400 V/50 Hz. AC Generator: Stamford HC 534C2, 450 KVA Manufacturer: Jenbacher Model: J 208 GS-C Type: Gas CHP Engine Serial Number: 21619 Engine power [KW]: 264 Electrical power [KWel]: 253 Speed [1/min]: 1,500 Year of Make: 1994 Hours: 67,000 Weight unit [kg]: 5,000 Dimensions LxWxH [cm]: 450 x 150 x 195 AC Generator Stamford HC 534C2 Manufacturer: Stamford Model No.: HC 534C2 Type: AC Synchronous Generator Serial number: 49059/2 Power [KVA]: 450 Voltage [V]: 231 / 400 Frequency [Hz]: 50 Current [A]: 649 Speed [1/min]: 1,500 Year of Make: 1994
Petrol engine ecodriver 180cc Auction-ID: A1-44050-49
Delivers 230 and 400 Volt voltage, power 6500 Watt. Auction-ID: A1-49862-14
Key data: 2000 KW, 2500 kVA, 400 V
2MW Cummins QSV91 available complete with control panel, gas line, heat exchanger, log books and maintenance manuals etc.
Key data: 75 KW, 112 kVA, 400 V
Buderus Gas CHP EN 70 MAN E0836 E302 Gas electricity and heat generator from 2014 with 81,648 operating hours. 1 available 70 KWel x 1,500 rpm, 400 V/50 Hz. AC Generator: Leroy Somer LSA 44.2 S7/4P, 112 KVA Manufacturer: Buderus Model No.: EN 70 Type: Gas CHP Engine: MAN E0836 E302 Serial Number: 100006776 Power [KW]: 75 Year of Make: 2014 Hours: 81,648 AC Generator Leroy Somer LSA 44.2S7/4P Manufacturer: Leroy Somer Model: LSA 44.2S7 C 6S/4 Type: AC Synchronous Generator Serial number: 30692/5 Power [KVA]: 112 Voltage [V]: 400 Frequency [Hz]: 50 Current [A]: 162 Speed [1/min]: 1,500 Year of Make: 2014 Weight [kg]: 440
feed pressure: . bar liter capacity: . l power capacity: . kW total power requirement: . kW weight of the machine ca.: . t dimensions of the machine ca.: . m The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
feed pressure: . bar liter capacity: . l power capacity: . kW total power requirement: . kW weight of the machine ca.: . t dimensions of the machine ca.: . m The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
feed pressure: . bar liter capacity: . l power capacity: . kW total power requirement: . kW weight of the machine ca.: . t dimensions of the machine ca.: . m The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
feed pressure: . bar liter capacity: . l power capacity: . kW total power requirement: . kW weight of the machine ca.: . t dimensions of the machine ca.: . m The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
feed pressure: . bar liter capacity: . l power capacity: . kW total power requirement: . kW weight of the machine ca.: . t dimensions of the machine ca.: . m The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
PRESS DESIGN drive system: eccentric / crank PRESS FORCES total force (nominal): 45 to PRESS TABLE table surface (left-right): 700 mm table surface (front-back): 440 mm opening in bed (diameter): 40 mm SLIDE table surface (left-right): 410 mm table surface (front-back): 280 mm stroke rate (max.): 110 /min SLIDE (MECHAN. PRESS) slide adjustment: 65 mm stroke min.: 0 mm stroke max.: 90 mm main drive power: 5.5 kW TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 380 mm distance between columns (H-frame): 360 mm ATTACHMENTS (PRESSES) 2-hand engagement: yes foot engagement: yes European CE standards: yes
Key data: 150 KW, 220 kVA, 400 V
Sokratherm Gas-CHP GG 140S oE Gas electricity and heat generator from 2010, with approx. 60,000 operating hours, with control and silencer. 1 available 140 KWel x 1,500 rpm, 400 V/50 Hz. AC Generator: MarelliGenerators MJB 250 LA4, 220 KVA Manufacturer: Sokratherm Model: GG 140S oE Type: Gas CHP Serial Number: F103064 Engine: MAN E2876 E312 Electrical power [KWel]: 140 Thermal power [KWth]: 216 Gas capacity [KWgas]: 392 Year of Make: 2010 Operating hours: approx. 60,000 Weight unit [kg]: 2,850 Dimensions LxWxH [m]: 3.00 x 0.9 x 2.4 AC Generator Marelli MJB 250 LA4 Manufacturer: MarelliGenerators Model: MJB 250 LA4 Type: AC Synchronous Generator Serial Number: MJB2572GT68MO Power [KVA]: 220 Voltage [V]: 400 Frequency [Hz]: 50 Current [A]: 317 Speed [1/min]: 1,500 Year of Make: 2010
PRESS DESIGN drive system: eccentric / crank PRESS FORCES total force (nominal): 50 to PRESS TABLE table surface (left-right): 700 mm table surface (front-back): 450 mm SLIDE table surface (left-right): 440 mm table surface (front-back): 360 mm spigot hole diameter: 40 mm stroke: 90 mm stroke rate (max.): 70 /min SLIDE (MECHAN. PRESS) slide adjustment: 70 mm stroke min.: 0 mm stroke max.: 90 mm main drive power: 3 kW TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 300 mm DIMENSIONS / WEIGHTS space requirements -left/right-: 700 mm space requirements -front/back-: 1295 mm total height: 2360 mm total weight approx.: 3000 kg
PRESS DESIGN drive system: eccentric / crank PRESS FORCES total force (nominal): 80 to PRESS TABLE table surface (left-right): 860 mm table surface (front-back): 620 mm thickness of bolster plate: 70 mm opening in bed (diameter): 165 mm SLIDE table surface (left-right): 570 mm table surface (front-back): 390 mm spigot hole diameter: 50 mm stroke: 120 mm stroke rate (max.): 67 /min SLIDE (MECHAN. PRESS) slide adjustment: 90 mm stroke min.: 9 mm stroke max.: 120 mm main drive power: 5.5 kW TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 360 mm DIMENSIONS / WEIGHTS space requirements -left/right-: 1420 mm space requirements -front/back-: 1700 mm total height: 2990 mm total weight approx.: 5600 kg
Key data: 48 KW, 60 kVA, 400 V
Execution: Category: Emergency Power Generator Stationary Aggregate type: stationary Design: Soundproofed Technical data engine: Engine manufacturer: Deutz AG Engine type: F 6 L 912 Motor power: 56 KW Cooling: Air-cooled Starting: Electric 12 V DC Speed: 1500 rpm Fuel: Low sulphur fuel oil Emission standard: TA-Luft Technical data generator: Generator manufacturer: Stamford Generator Type: S1L2-Y Generator power: 60 kVA Generator current: 86.40 amps Short-circuit current: 259.2 amps Overload: 95.04 amps Voltage 400 / 231 Volt Voltage regulator: yes electronic AVR Power factor: cos. - PHI 0.8 Speed: 1500 rpm Switchgear: Version: Automatic start Functions: Emergency power operation Switch: Generator switch 4 poles Delivery set up Base frame tank with drip pan Capacity / litre: 1 ...
x-travel: 1.050 mm y-travel: 610 mm z-travel: 610 mm control: HEIDENHAIN iTNC 530 Distance between table and spindle: 100-710 mm table-size: 1.200 x 600 mm table weight: 1.200 Kg rapid travel x/y/z: 30.000/20.000 mm/min feed: 12.000 m/min spindle taper: BT-40 spindle turning speed range: 60 - 10.000 U/min spindle drive: 7,5/11 kW Tools changer: 20 pos. Internal cooling system: 20 bar Chip coveyor: 2 handwheel: HEIDENHAIN HR-410 tool diameter: 100 mm tool length - max.: 320 mm weight of tools max.: 10 kg total power requirement: kW weight of the machine ca.: 7 t dimensions of the machine ca.: 2.900 x 3.420 x 2.888 m Complete installation 4th axis - Rotary table Golden Sun CNCT 321 (4th/5th axis)- Rotary table diameter 200 mm. - Rotary table tailstock - ZF box - Electrical cabinet air conditioning The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Generator unopened Auction-ID: A1-41951-150
maximum number of results exceeded
please refine your search
1.050 € 
