We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
119,597 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
LVD MVN 3100 x 6,35 mm Cutting length: 3100 mm Max sheet thickness st 45: 6 mm Backgauge: no backgauge
Bombled 2100 x 2 mm Max sheetthickness: 2 mm Cuttinglength: 2100 mm
new
NC - controlled mechanical sheet metal panel scissors in backdrop cutting design, maximum cutting length 1,050 mm, maximum cutting capacity 4 mm steel sheet/ST40, cutting angle 1.5°, NC - controlled rear stop with 1,000 mm travel range - automatic removal of the stop rail at sections lower than 1,000 mm - optionally available with a foldable sheet support at the rear stop or a conveyor belt with upliftrs, drive power 5 kW, weight approx. 2,500 kg
new
Hydraulic sheet metal shears in backdrop cutting design with NC - controlled rear stop - manual cutting angle adjustment and hydraulic cutting gap adjustment, maximum cutting length 3,020 mm, maximum cutting capacity 8 mm steel sheet/ST40, cutting angle 0.5° to 2° NC - controlled rear stop with 1,000 mm travel range - automatic removal of the stop rail at sections deeper than 1,000 mm - optionally available with a foldable sheet metal support at the rear stop or a conveyor belt with high-stop strips, drive power 11.5 kW, dimensions 3.6 x 1.2 m, weight approx. 7,600 kg
new
We supply round and flange ring shears (circular shears) in two sizes - 3/1300 and 5/1800 Our KS circular shears are PLC - controlled hydraulic - electromechanical machines designed for the production of rounds and flanges made of steel sheet, VA stainless steel sheet, Aluminium and non-ferrous metal sheet, maximum shearing performance for sheets with a tensile strength of 400 N/mm2 - 0.5 mm to 3 mm or 0.5 mm to 5 mm, smallest / largest cutable circular board 150 mm / 1,300 mm or 1,800 mm respectively – cutting speed up to 35 m/min, drive power 5 kW or 7.5 kW, weight approx. 2,000 kg and 3,000 kg
new
Mechanical manual sheet metal shears of excellent quality, for the burr-free precision cutting of fine sheets up to 1 mm sheet thickness steel sheet/ST40 – aluminium 1.2 mm, backdrop-guided knife beam, maximum cutting length 3,080 mm, cutting angle 1.5°, manually operated rear stop with 750 mm travel range - +/- 5 mm slantable for conical cutting, optional with sheet metal high-holding device and automatic tipping device for the sheet metal cuttings in the section collection trolley, scissor table height 800 mm - scissor table width 300 mm - scissor table support width up to 480 mm, dimensions 3.55 m x 1.6 m x H 1.3 m, weight approx. 790 kg
new
PLC - controlled round and flange ring shears (circular scissors) This can also be expanded into a combined circular scissors - flange machine. We supply the machine in semi-automatic design and as a fully automated production island. Rounds and flanges (sheet rings) made of steel sheet, VA stainless steel sheet, aluminium and non-ferrous metal sheet can be cut, maximum shear performance for sheets with a tensile strength of 400 N/mm2 - 0.5 mm to 12 mm, smallest / largest cutable circular board 500 mm to 2,200 mm – cutting speed up to 25 m/min, drive power 15 kW, weight of the base machine
used
Hydraul. Table scissors, used, ready for demonstration under electricity hydraulic plate shearer, used , under power, ready for operation Type: XTSL 3016 Fabr./ make : Atlantic Year of construction/ year: 1993 Sheet thickness with the largest sheet width/ thickness at max. cutting length: 16 mm ( structural steel / mild steel ) 12 mm ( stainless steel / high grade steel) Cutting width/ cutting length: 3100 mm Weight/ weight: approx. 14 t Specification: Rear stop / backstop
used
Used JMC 407 Kat Alligator Scissors Alligator scissors JMC 407Cat The catalyst version JMC 407 has an additional "V-holder" in the cutting area for adjustment when cutting or opening the catalysts. In stock at the end of March 2021 Knife length: 407 mm Measuring opening: 250 mm Cutting capacity: 90 tons Round iron ST 37: 57 mm diameter Number of strokes at 1/4 opening: 63 / min Number of strokes at full opening: 11 / min Dimensions (L x W x H): 1550 x 880 x 1120 mm Weight: 880 kg Drive: 7.5 kw / 380 V Operation: Foot pedal
used
Qty. 1 Second-hand strip rolling mill Mfc.: United Engineering Type: 4-Hi Built: Strip Width: 393 mm (15.5”) Thickness Entry: 4 mm (0.16”) Exit: 1.2 mm (0.05”) Mill Speed: 405 m/min. (1330 Fpm) Strip Tension: 2670 kg (5875 Lbs) Coil ID 406 mm (16”) Coil OD 1448 mm (57”) Coil weight: 3180 kg (7000 lbs)
used
No. 3554: 1 gebr. Table scissors Fabr. SCHARRINGHAUSEN, type HS/S, Bauj. 1952 Arb.-Ber.: 2050 x 2 mm, Other: adjustable rear stop 600 mm good condition
used
Max. diameter 240 - 2000 Max. plate thickness 10 mm Main motor power 5,5 HP
used
Description Table shears from Weipertsuitable for tools, fixture construction, training and mould making Cutting length 3200mm Sheet thickness 16mm Technical data Sheet thickness (max.) 16 mm Working length 3,080 mm Extension 150 mm Cutting angle 0.3 - 2.5 degrees Strokes per minute 14 h/min Holder 18 pieces Holder pressure capacity 40 t Table dimensions 3.380x550x840 mm Backstroke Backstop depth 1,000 mm Front support arms Number of support arms 3 pieces Length of support arms 900 mm Drive power Engine power main drive 37 kW Hydraulic oil tank volume 350 l Dimensions and weights Dimensions (length x width x height) 4x2.2x2.42 m Weight 15.300 k
used
Key data: 3100 mm, 6 mm
HACO TS 3006 hydraulic guillotine shears manufactured in Belgium in 2006, are used in manufacturing plants to cut steel sheets with a maximum length of 3100 mm and a thickness of 6 mm. The machine has vertically aligned knives with four cutting edges, which ensure high precision and quality machining of workpieces regardless of the thickness and type of sheet. The angle of the cutting knives and the gap between them are adjusted by means of two levers at the rear of the machine. During machining, the workpiece is pressed against the cam in order to take an accurate measurement on the gauge located between the front stop and the bottom knife. Two parallel hydraulic cylinders drive the cutting bar (the upper knife attached to the slider) to perform the movement in the up-down direction. The HACO guillotine shears are offered with equipment which includes a foot control, a modern HACO SP ...
used
Cutting lenght 6000 mm Cutting thickness 12 mm
used
Hand lever shears, hand tin snips, tin snips, sheet metal snips -Scissors: 240 x 4 mm -Transfer in current condition as seen -Dimensions: 400/150/H1200 mm -Weight: 46 kg
used
Scrap scissors hydraulic with petrol engine
used
Cable shears -Cable shears: hydraulic -without: hydraulic unit -Max. Opening: 95 mm -Number: 1x cable shears available -Dimensions: 530/180/H80 mm -Weight: 13.3 kg
used
Long knife, sheet metal and round steel shears -Sheet metal shears: stable -Material: flat steel -Round: up to 15 mm -Square: up to 15 mm
new
: neu : ca. 12 Wochen ab Auftrags : 1280 mm : 16 mm : 12 mm : 8 1/min : 3 ° : 7 pcs. : 500 mm : 22.5 kW : 250 l : 950 mm : 2100 mm : 1400 mm : 2000 mm : 5000 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
: neu : ca. 8 Wochen ab Auftragse : Spanien : 170 to : 40x40x4 mm : 65x65x7 mm : 2 : 25/5 bzw- 18/7 mm : 350 to : 5 kW : 265 bar : 70 l Automatic line for punching and sharing angle STANDARD EQUIPMENT: INFEED/OUTFEED CONVEYERS idle rollers 3 conveyers each 3,3 m for feeding angles up to 12 m length WORKING UNITS: ROLLER FEED MEASURING SYSTEM feed by roller wheel (brushless moto),rotary encoder no time loss for measuring feeding speed variablefrom 0 to 36 m/min positioning accuracy in X axis0,25 mm + 0,15 mm per meter the last 250 mm can not be used PUNCHING UNIT (2X) 1 punching unit per leg 1 punch per punching unit adjustable back mark by tooling fromfrom 20-40 mm hydraulic downholder direct access for quick change ofpunches and dies SHEARING UNIT shearing power 350 kN single cut direct access for quick change ofshearing blade hydraulic downholder CNC CONTROL OMRON PLC colour touchscree ...
used
Baykal 3000 mm x 10 mm NC Guillotine Shear Machine is in good condition
new
: neu : ca. 12 Wochen ab Auftrags : 1530 mm : 16 mm : 12 mm : 7 1/min : 3 ° : 8 pcs. : 500 mm : 22.5 kW : 250 l : 950 mm : 2350 mm : 1400 mm : 2000 mm : 5200 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Ozamech hydraulic guillotine, bending length 3000mm Used machine efficient, sale due to liquidation of the company.
new
: 28 min. Punching force: 110 to : 40x20 mm flat steel: 600x15 oder 400x20 mm L-beam 90°: 160x160x16 mm L-beam 45°: 70x70x7 mm : 50 mm square edge steel: 50 mm : 13 mm throat: 300 mm Basic equipment: - Complete set of blades for flat steel shears - Complete knife set for bar cutter - Complete knife set for angle steel shears - Compl. Standard punching device - Stamp quick release device for punches up to 40 mm diameter - Rectangle notch compl. with hold downs - Complete knife set below for rectangular notching - Upper tool for rectangular notching - Support table for flat material - Punching table with stop - Notch with stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Hydraulic guillotine shear model Atlantic 3012 very good condition. - Year of manufacture - 1990. - Length of the cut sheet - 3000mm. - Max cutting thickness 12mm - The machine is equipped with an automatic bumper. - The machine has 1 set of spare original knives. - Weight 8000 kg.
used
Durma MS 3004 Guillotine Shear Machine is like new condition
new
flat steel: 350 x 10 mm round bar steel: 35 mm square edge steel: 30 mm L-beam: 80x80x8 mm hole diameter in sheet thickness: Ø 27 in 13 bzw. Ø 20 in 8 mm : 500 kN throat: 177 mm : 34 (Hub 15mm) blade length: 356 mm engine output: 3.0 kW weight: 950 kg dimensions: 1300x1100x1850 mm Standard equipment: - Knife set for flat steel - Complete knife set for angle steel shears - Complete normal punching equipment - Quick release device for punches up to 31 mm - Support table for punching device, rectangular notching and flat steel shears - Bending stamp with matrices V 40 and V 70 - Electric contact stop (1.000 mm) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Folding table at the rear 12mm aluminum / 8 steel thickness Sharpening knife CNC Backgauge Opening Stroke 190mm
used
Dener DMMH-NC/31-10 Guillotine Shear Cutting length : 3100 mm Maximum cutting thickness : 10 mm Machine is in good condition
used
Cutting length : 3100 mm Cutting thickness : 10 mm Machine is in good condition
new
sheet width: 3100 mm plate thickness: 10 mm cutting angle: 2 ° down holder: 14 Stück no. of strokes: 13 Hub/min throat: 350 mm oil volume: 260 l total power requirement: 22 kW weight of the machine ca.: 10.550 kg dimensions of the machine ca.: 4000x2250x2050 mm Domestic equipments: - Hydraulic swing cut sheet metal shears - Touch screen controller with digital display for backgauge - automatic kerf adjustment via the control - Backgauge control 1000 mm travel with recirculating ball screws - Vibration cutting machine with kerf adjustment - 2 support arms - 1 side stop - Photocell behind the machine - Cutting length limit - cut line lighting - Chrome steel knife - Ball rolls in the table - hinged finger guard with limit switch - Footswitch - CE mark / Declaration of Conformity - Bed instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTe ...
used
Durma SBT 3006 CNC Guillotine Shear Cutting length : 3000 mm Maximum cutting thickness : 6 mm Pneumatic sheet support
new
sheet width: 3100 mm plate thickness: 6 mm voltage: 380 V control: CYBELEC CybTouch down holder: 14 Stück cutting angle: 1,2 ° total power requirement: 11 kW weight of the machine ca.: 5700 kg dimensions of the machine ca.: 4000x2100x1640 mm Accessories / equipment: - CYBELEC Cybtouch touch screen controller - NC controller for backgauge, gap adjustment, number of pieces, cutting length - 1 side stop with scale, T-groove and tilting cam - 2 front support arms - cut line lighting - Cutting gap adjustment - Cutting length limit - Folding finger guard with limit switch - motorized back gauge 1.000 mm travel - Ball screws - Photocell behind the machine - Ball rolls in the table - SIEMENS electrical system - BOSCH / HOERBIGER hydraulic system - Footswitch - CE mark / Declaration of Conformity - Operating manual: Machine and control in German The data for this ad was created with ModulMWS ...
new
: 32 /min Punching force: 60 to throat: 500 mm : 40x11 mm : 350x15 mm : 350x15 mm L-beam 90°: 120x120x10 mm : 45 mm square edge steel: 40 mm : 10 mm : Aufnahme bis max. 150x10 engine output: 5,5 kW weight: 2012 kg Basic equipment: - Flat steel shears with knife set - Angle shears with knife set - Punch with quick release device for punches up to 40 mm - Support table for punching device - Triangular notching device - Support table for notching - bending station - Bending stamp with matrices V 40 and V 70 - electrical contact stop (1 meter) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
: 32 /min Punching force: 60 to throat: 250 mm : bis max. Ø 40x11 mm : 350x15 mm : 350x15 mm L-beam 90°: 120x120x10 mm : 45 mm square edge steel: 40 mm : 10 mm : Aufnahme bis max. 150x10 engine output: 5,5 kW weight: ca. 1600 kg Basic equipment: - Flat steel shears with knife set - Angle shears with knife set - Punch with quick release device for punches up to 40 mm - Support table for punching device - Triangular notching device - Support table for notching - bending station - Bending stamp with matrices V 40 and V 70 - electrical contact stop (1 meter) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Durma SBT 3010 CNC Guillotine Shear Machine is in very good condition
new
Punching force: 45 t hole diameter in sheet thickness: Ø 27x13 mm : 24 /min L-beam 90°: 80x80x8 mm L-beam 45°: 60x60x6 mm flat steel: 200x13 mm : 7 mm engine output: 2,2 kW weight: 760 kg Basic equipment: - Complete set of blades for flat steel shears - Complete knife set for angle steel shears - Compl. Standard punching device - Stamp quick release device for punches up to 27 mm diameter - Rectangular notching device compl. with hold down - notch - Support table for punching device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Durma VS 3020 CNC Guillotine Shear Maximum cutting thickness : 20 mm Cybelec control unit Stroke : 190 mm Number of cut per minute : 7-13 Machine is in good working condition
used
Punching force : 30 Ton Sharing Force : 25 Ton Machine is in excellent condition
used
Cutting length : 3000 mm Maximum cutting thickness : 6 mm Machine is in good condition Machine can be sold as set with press brake : https://www.makinaalsat/makinalar/172773/durmazlar-abkant-pres
used
: 10 mm Punching force: 55 to : 40x10 mm flat steel: 300x15 oder 200x20 mm L-beam 90°: 120x120x10 mm L-beam 45°: 70x70x7 mm : 40 mm square edge steel: 40 mm : 37 /min. throat: 250 mm weight of the machine ca.: 1.600 kg Basic equipment: - Complete set of blades for flat steel shears - Complete knife set for bar cutter - Complete knife set for angle steel shears - Compl. Standard punching device - Stamp quick release device for punches up to 40 mm diameter - Rectangle notch compl. with hold downs - Complete knife set below for rectangular notching - Upper tool for rectangular notching - Support table for flat material - Punching table with stop - Notch with stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Baykal HNL 3100x10 mm CNC Hydraulic Guillotine Shear Adjustable angle Cutting length: 3100 mm Maximum cutting thickness : 10 mm Machine is in good condition
used
Ermak CNC HVR 3100 x 10 CNC Guillotine Shear Machine is in very good condition
used
Esa S 530 Control Unit Folding length : 3100 mm Cutting thickness : 6 mm
new
sheet width: 3100 mm plate thickness: 6 mm voltage: 380 V control: CYBELEC CybTouch down holder: 14 Stück cutting angle: 1,2 ° total power requirement: 11 kW weight of the machine ca.: 6.300 kg dimensions of the machine ca.: 4000x2100x1640 mm Equipment: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Quantity Cutting length limitation Material preselection, including sheet thickness Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. can be folded up at max. Traverse path, for longer cuts - 1x side stop - 2x front support arms - Ball casters in the front support table - hinged finger protection, with safety switch - BOSCH / HOERBIGER hydraulic system - SIEMENS electrical system - light barrier behind the machine (safety device) - fo ...
new
: 45 to. no. of strokes: 24 Hub/min hole diameter in sheet thickness: max. Ø 27 in 13 mm : 80x80x8 : 60x60x6 mm flat steel: 300x10/200x13 mm : 7 mm engine output: 2.2 kW range L-W-H: 1550x820x1540 mm weight: 760 kg Standard equipment: - Complete knife set for flat steel shears - complete knife set for angle steel shears - complete standard punching equipment - Stamp quick release device for punches up to Ø 27 mm - Rectangular notching device complete with hold-down device - notch - Support table for punching device The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
sheet width: 3100 mm plate thickness: 13 mm thickness at Niro-steel: 8 mm control: CYBELEC CybTouch down holder: 14 Stück cutting angle: 2,0° ° no. of strokes: 11 Hub/min voltage: 380 V total power requirement: 22 kW weight of the machine ca.: 12.100 kg dimensions of the machine ca.: 4000x2240x2235 mm Accessories / equipment: - CYBELEC-CybTouch control panel with digital display for backgauge - hydr. Cutting gap adjustment via control - 1 side stop - 4 front lifting arms - cut line lighting - Cutting gap adjustment - Cutting length limit - Ball rolls in the table - motorized back gauge 1.000 mm travel with recirculating ball screws, automatically start at the end of the stop - Shear knives for stainless steel cuts as standard - Photocell behind the machine - SIEMENS electrical system - BOSCH / HOERBIGER hydraulic system - Footswitch - Operating instructions in German The data f ...
used
Durma SBT 3006 Hydraulic Guillotine Shear Cutting length : 3100 mm Cutting thickness : 6 mm Machine is in good condition
used
Durma CNC HGM 6013 Guillotine Shear Machine is in good condition Cutting length : 6000 mm