plastic injection moulding used for sale

Key data: 1500 kN, 415 g/PS, 55 mm

Built in 1999 Clamping force: 150 tons. Screw diameter: 55 mm Displacement: 456 cm³ Spray pressure: 1564 bar Very good condition!

clamping force: 1500 kN injection volume: 141 g/PS screw diameter: 35 mm platen size: 470 x 470 mm Condition: used, Specification: horizontal injection moulding machine, Type: Allrounder 470C 1500-400 GE GOLDEN EDITION Injection unit: - Screw diameter: 35 mm (wear-resistant) - Centring ring diameter: 125 mm - Max. shot weight: 141 g (PS) - Injection pressure: 2,500 bar Closing unit: - Clamping force: 1,500 kN - Max. opening stroke: 750 mm - Mould installation height: min. 250 mm - Mould clamping plates: 470 x 470 mm - Approx. operating hours: 79,000 h (still in use) - Operating voltage: 3x 400 V, 50 Hz - Nominal motor heating current: 75 / 40 A - Total current: 115 A - Total connection: 65 kW - Core pulls: 1x - Hot runner control points: 6x - Temperature control unit interfaces: 6x (20 mA) - Approved for high temperatures  ...

Key data: 500 kN, 95 g/PS, 30 mm

Year of Make: 2005 Clamping force: 50 tons. shot volume: 106 cm³ shot weight: 95 gr./PS Screw diameter: 30 mm with take off robot Good condition

TECHNICAL DATA OF THE MACHINE General Clamping force: 50 t Year of manufacture: 2006 Control: NC4 Weight: 2,700 kg Dimensions (L × W × H): 3.8 × 1.1 × 2.1 m Injection unit – .../200 Screw diameter: 22 mm Injection volume: 41.8 cc Specific injection pressure: 2,800 bar Closing system – 50/... Clamping force: 50 t Tool plate dimensions: 520 × 520 mm Clearance between columns: 355 × 355 mm Tool height: 210 mm Opening Distance: 400mm Maximum Plate Distance: 610mm

Extruder + electric cabinet output: 200 kg Heads not included Winder not included

Ref. no.: 17507 Manufacturer: DEMAG Year of construction: 1998 Clamping unit Clamping force: 80 ton Opening stroke: 450 mm Distance between tie bars: 370 x 370 mm Mould height min.: 200 mm Platen size (h x v): 600 x 600 mm Injection unit Screw diameter: 35 mm Injection volume: 168 cm³ Shot weight: 149 g Injection pressure: 2020 bar Measurements and weight Dimensions: 4,1 x 1,4 x 2,0 m Machine weight: 3700 kg

3 x Injection moulding machines Stork 440 to 1 x Injection moulding machine Stork 660 to 2 x Injection moulding machine Stork 900 to

Injection Molding Machine FCS SD 6000 BJ 2016

Key data: 5000 kN, 2 g/PS, 90 mm

1.0 St. gebr. Injection Molding Machine Manufacturer: KRAUSS MAFFEI Type: KM300-1900CX Year of Make: 2011 Clamping force: 300 tons Spar spacing 630 x 630 mm Screws DN: 60 mm Maximum displacement: 769 cm³ Moulded part weight: 692 g/hp Control: MC6 Equipment: 3 pcs. core train Djbr Rvoxyrc Isf Nysul Interface Robot 45-fold hot zone channel control Interface temperature control unit Approx. 51,000 operating hours

Key data: 2500 kN, 579 g/PS, 60 mm

1.0 St. gebr. Injection Molding Machine with Robot Manufacturer: DEMAG Type: ET250-840 Concept Year of Make: 2004 Clamping force: 250 tons Spar spacing 630 x 630 mm Screws DN: 60 mm Max. displacement: 636 cm³ Moulded part weight: 579 g/hp Control: NC5 Equipment: Robot manufacturer: WITTMANN, type: W633-931 2 pcs core train

Key data: 600 kN, 94 g/PS, 30 mm

1.0 St. gebr. Injection Molding Machine with Robot Manufacturer: DEMAG Type: ET60-200 Concept Year of Make: 2003 Clamping force: 60 tons Spar spacing 420 x 420 mm Screws DN: 30 mm Max. displacement: 106 cm³ Moulded part weight: 94 g/hp Control: NC5 Equipment: Robot manufacturer: WITTMANN, type: W621-1381 2 pcs core train

Key data: 4200 kN, 2 g/PS, 80 mm

1.0 St. gebr. Injection Molding Machine Manufacturer: KRAUSS MAFFEI Type: KM420-4300CX Year of Make: 2012 Clamping force: 420 tons Spar spacing 800 x 800 mm Screws DN: 80 mm Max. displacement: 1,810 cm³ Moulded part weight: 1,647 g/hp Control: MC6 Equipment: 2 pcs core train Interface Robot 12-way hot zone channel control Interface temperature control unit

Key data: 2500 kN, 476 g/PS, 55 mm

1.0 St. gebr. Injection Molding Machine Manufacturer: KRAUSS MAFFEI Type: KM250-1000CX Year of Make: 2017 Clamping force: 250 tons Spar spacing 630 x 630 mm Screws DN: 55 mm Max. displacement: 523 cm³ Moulded part weight: 476 g/hp Control: MC6 Equipment: 2 pcs core train Interface Robot 12-way hot zone channel control Interface temperature control unit

Injection moulding machine Battenfeld Machine Type TM 2700/2800 Control Type B2 Year of construction 2003/04 Screw diameter 75 mm

Injection moulding machine Krauss Maffei KM 800-5700 BJ 1999 Technical data on request

Arburg 570C2000-800 FY2006 Golden Edition, 1 core hoist, 1 conveyor belt 33.400 Multilift SELECT 6kg Arburg 470C-2000-800 FY2005 No core features; 1 conveyor belt

year 2009. injection volume 9 cm3. Immediate ex stock available

2 x injection moulding machines EL - EXIS 200 S incl. Wittmann robot cell for removal and feeding ( No IML ) EL - EXIS 300 S incl. Wittmann robot cell for removal and stacking ( no IML )

Injection moulding machine Arburg 820S 4000-4600 BJ 2016

Injection moulding machine Engel DUO 4550/800 BJ 2004

- Battenfeld TM3500 / 1900 BJ 2002 or 2001 control B4 without robot for sale. - The machine is currently running in production, no defects.

Injection molding machine Haitian Zerres ZE600 built in 2019 and MB Conveyors conveyor belt from 2015.

Key data: 1500 kN, 359 g/PS, 50 mm

Year of construction 2011 + 2012 Clamping force: 150 tons. Screw diameter 50 mm Injection weight PS: 359 g Injection pressure: 2000 bar tie bar distance: 520 x 520 mm Machines are in good condition, and still in production

Key data: 220 kN, 27 g/PS, 22 mm

1.0 St. gebr. Injection Molding Machine Manufacturer: DR. BOY Type: 22 D Year of Make: 1999 Clamping force: 22 tons Tiebar spacing: 254 x 254 mm Installation height MIN, / MAX. 200 / 400 mm Screws DN: 22 mm Moulded part weight 27 g/hp

Key data: 220 kN, 27 g/PS, 22 mm

1.0 St. gebr. Injection Molding Machine Manufacturer: DR. BOY Type: 22 D Year of Make: 2004 Clamping force: 22 tons Tiebar spacing: 254 x 254 mm Installation height MIN, / MAX. 200 / 400 mm Screws DN: 22 mm Moulded part weight 27 g/hp

Key data: 1400 kN, 139 g/PS, 35 mm

1.0 St. gebr. Injection Molding Machine with Robot, Machine comes from cleanroom production Manufacturer: ENGEL Type: VICTORY 330/140 TECH Year of Make: 2011 Clamping force: 140 tons Spar spacing: SPARLESS Screws DN: 35 mm Max. displacement: 154 ccm³ Moulded part weight 139 g/hp Control: CC200 Equipment: -Robot, manufacturer: Engel, type: V12 -2 x Core Pull -Blow-out valve -16 hot runner control zones -Protective fence -Conveyor belt

2 x Injection moulding machines Engel VC 2460/180 tech BJ 2023

Key data: 500 kN

Clamping force: 500 kN Clamping plate: 540 x 540 mm Tool opening travel: 350 mm Tool installation height min.: 200 mm Opening width: 500 mm Ejector stroke: 100 mm Total weight: approx. 2,300kg

Injection moulding machine Battenfeld BK T 2500 BJ 1991

used Arburg 520C 2000-675, built in 2000 for sale: Machine cycles = 3.6802.856 Pump hours = 46,142 Operating hours automatic = 37,814 Screw diameter = 60 mm Machine with safety fence and with used auxiliary unit, but without conveyor, without hopper and without handling. The machine is currently still connected, a visit would be possible at short notice.

clamping force: 450 kN injection volume: 135 cm³ screw diameter: 35 mm platen size: 550 x 430 mm Condition: second-hand, Specification: Horizontal injection moulding machine Injection unit: - Screw diameter: 35 mm - Screw length L/D: 17.3D - Dosing stroke: 140 mm - Screw speed: 20 – 480 rpm - Moulding volume: 135 cm³ - Injection pressure: 1,065 bar - Increased injection pressure: 1,620 bar - Heating power: 6.8 kW - Number of heating zones (including nozzle): 4 Clamping unit: - Maximum clamping force: 450 kN - Platen dimensions: 550 x 330 mm - Extended clamping plates: 550 x 430 mm - Minimum mould installation height: 180 mm - Maximum plate spacing: 530 mm - Opening stroke: 350 mm - Control system: EC 100 Drive: - Pump drive power: 11 kW - Approx. weight: 3,300 kg - Dimensions: 3,300 x 1,200 x 1,800 mm Current oper ...

clamping force: 4.000 kN injection volume: 2480 cm³ screw diameter: 90 mm platen size: 1.300 x 1.080 mm Condition: second-hand, Specification: Horizontal injection moulding machine Injection unit: - Screw diameter: 90 mm - Injection volume: 2,480 cm³ - Maximum shot weight: 2,232 g - Injection pressure: 1,360 bar - Increased injection pressure: 1,600 bar - Heating capacity: 64 kW Clamping unit: - Max. clamping force: 4,000 kN - Clamping plates: 1,300 x 740 mm - Extended clamping plates: 1,300 x 1,080 mm - Minimum mould installation height: 350 mm - Maximum platen spacing: 1,300 mm - Opening stroke: 950 mm - Core pull unit: 2-stage on BAP - Control system: EC 100 Drive: - Pump drive power: 55 kW - Weight (clamping side) approx.: 25,000 kg - Weight on injection side (approx.): 8,000 kg Discharge  ...

Key data: 4200 kN, 527 g/PS, 70 mm

1.0 St. gebr. Injection Molding Machine with Robot Manufacturer: KRAUSS MAFFEI Type: KM420-1900C2 Year of Make: 2006 Clamping force: 420 tons Spar spacing 800 x 800 mm Screws DN: 70 mm Max. displacement: 1,047 cm³ Moulded part weight: 853 g/hp Control: MC5 Equipment: 2 pcs core train Robot SEPRO, type: SR4030 S3 VISUAL 12-way hot zone channel control Interface temperature control unit

Engel 3 ES 7050 / 1 500 Duo built in 1999 against bid.

Injection moulding machine Ferromatik Elektra 50-300 selection BJ 2008 Injection Molding Machine Ferromatik Basetec 85-493-520 BJ 2009 Injection moulding machine Ferromatik Elektra 1100-450 evol. Year of manufacture 2006 Injection moulding machine Ferromatik K 110s-2F BJ 1999 Injection moulding machine Ferromatik K 125s/2F BJ 1995 Injection moulding machine Ferromatik K 200s-2F -493 BJ 1999 Angel Priam Bito Leo Locative Hot runner regulator Gammaflux G 24 Conveyor belts Temperature control units Accessories Walther Couplings

clamping force: 600 kN injection volume: 106 cm³ screw diameter: 30 mm platen size: 590 x 600 mm Condition: used, Specification: Horizontal injection moulding machine, type: System 60/420-200 - Internat. Size specification: 600 - 200 injection unit: - Screw diameter: 30 mm - L/D - ratio: 20D - Injection volume: 106 cm³ - Injection pressure: 1995 bar - Cylinder heating: 8,3 kW clamping unit: - Clamping force: 600 kN - Max. opening stroke: 450 mm - Mould installation height: min. 250 mm - Max. platen distance: 700 mm - Mould clamping platens: 590 x 600 mm - Clear column distance: 420 x 420 mm Total machine: - Oil tank filling: 180 ltr. - Pump capacity: 22 kW - Voltage: 3x 400V, 50 Hz - total power: 30,3 kW - Dimensions L/W/H: approx. 4200 x 1400 x 2000 mm - Weight without oil approx.: 3,950 kg - 2x core pull Plant is still in ...

clamping force: 600 kN injection volume: 144 cm³ screw diameter: 35 mm platen size: 570 x 570 mm closing stroke: 500 mm Condition: used Specification: Horizontal injection moulding machine clamping unit: - Clamping force max.: 600 kN - clamping platens: 570 x 570 mm - clear column distance: 370 x 370 mm - Distance between the mould mounting platens: 750 mm - Mould installation height: 250 mm - Opening stroke max.: 500 mm - Ejector travel hyd. Ejector stroke: 175 mm - Ejector force max.: 40 kN Injection unit: - Screw diameter: 35 mm - Screw length: 20D - Screw stroke max.: 150 mm - Max. dosing volume: 144 cm³ - Moulded part weight: 121 g - Injection pressure: 1,820 bar - Injection flow max.: 154 cm³/s - Screw peripheral speed: 57 m/min - Screw torque max.: 440 Nm - Barrel and nozzle heating: 1600 +  ...

NETSTAL SYN 1500-460 ist eine Plastikspritzmaschine, ausgelegt für Präzision, hohe Genauigkeit und Zuverlässigkeit. Kapazitäten: Schliesskraft: 150 to; Hubvolumen: 201 cm3; Schneckendurchmesser: 40 mm; Auswerferhub: 150 mm; Auswerferkraft: 49 kN; Einspritzdruck: 2218 bar. Technische Daten: von 20 t/min bis 300 t/min; Formenheizung 20 kW; Schneckengetriebemotor 30 kW; Maschinengewicht ca. 9000 kg; Maße L×B×H 5700×1650×2220 mm. Erreicht enge Toleranzen; geeignet für Automotive, Medizintechnik, Luftfahrt und Elektronik Technische Daten ohne Gewähr

Injection moulding machine Ferromatik Elektra 50-300 selection BJ 2008

Injection moulding machine Ferromatik basetec 85-493-520 BJ 2009

Injection moulding machine Ferromatik Elektra 1100-450 evol. Year of manufacture 2006

Injection Molding Machine Ferromatik 110s-2F BJ 1999

Injection moulding machine Ferromatik K 125s/2f BJ 1995

Injection moulding machine Ferromatik K 200s /2F-493 BJ 1999

AB25V: Designation: Arburg 275 V 250-70 Year of Make: 2007 Clamping force: 250kN Screw diameter: 18mm Tiebar spacing: 275 x 275 FROM 50V: Designation: Arburg 375 V 500-100 Year of Make: 2008 Clamping force: 500kN Screw diameter: 15mm Tiebar spacing: 375 x 375

Well used Krauss Maffei free loaded truck to return.

Injection moulding machine Arburg 1500 T 2 K BJ 1999

with spare screw, high-pressure hose and various spare parts - see pictures

Engel injection moulding machine old

2 pcs. molds with 1-1 cavity, automat with hot runnel control, PP material molds sizes both: 300x245x213 mm machine size min. 25 T