plant mill used for sale

This skid mounted pilot pasteurisation plant exisiting out of a inline filter, feed screw pump (Bominox - type RS-22/M - 0,75 kW - n2: 250 rpm), level tank of ± 100 liter (internal diameter 45 cm, internal height 70 cm) with mix agitator (0,18 kW - 665 rpm), pre-heater (tubular heatexchanger), homogeniser (FBF 001), 2x tubular heaters, holding, 2 tubular coolers and a double jacketed ripening tank of ± 250 liter (internal diameter 70 cm, internal height 63 cm) with propellor agitator (0,37 kW - n2: 50 rpm). The pilot pasteurisation plant is previously used for ice cream mixture and only run for 357 production hours., The unit can be used for all kind of different combinations for pasteurisation and homogenising of liquid products, by making different connections on the flowplates., Homogeniser details:, Manufacturer: FBF Italia, Model: FBF 001, Serienr: 06031808, Year: 2006, Max. capac ...

Tetra Pak desserts pilot UHT plant with an pasteurisation, indirect and/or direct (VTIS) heating module @ 225 ltr/h and only a pasteurisation step @ 125 ltr/h, previously used in a R&D centre for desserts., Indirect unit, skid mounted, including:, - Open level tank, serial number: DFB-5259-BT01, year 2008, 50 ltr with propellor agitator (Lightnin ECL-M59-25)., - Feed pump (mono / screw pump, Netzsch, NM031BH02S12H, serial number 387231, year 2007, 120 - 300 ltr/h, speed 20 - 80 rpm, discharge pressure 2 bar, product temperature 5 - 20 °C)., - Lobe pump, Alfa Laval, SRU1/005/LD, serial number 431441, year 2008, motor: 0,37 kW, 400 V, 50 Hz, n1: 1.360 rpm, i: 15,57 n2: 89 rpm., - Heating module A, centrifugal pump: Alfa Laval FM-0/95, serial number: 31457-17997., - Heating module B, centrifugal pump: Alfa Laval FM-0/95, serial number: 31457-17999., - Heating module C, centrifugal pump: Al ...

Margarine pilot plant with 1x high pressure pump, 3x crystalizer scrap surface heat exchangers (SSHE), 1x pin worker (1 - 2 and 3 liter), 1x phase inverter, 1x cooling unit (R22) and control panel. Working product pressure of the pilot plant up to 80 bar (8000 kPa). Capacity up to 90 kg per hour., - High Pressure Pump, High Pressure Pump for pumping the margarine emulsion through the margarine pilot plant. Gerstenberg & Agger A/S, type Labo Pump 2-22-4 , serial number 12.211, year 1990, product pressure max 80 bar, temperature max 100 °C, capacity max 200 kg/h, motor 415 V - 50 Hz - 1,1 kW. Control panel with Siemens S7-200 PLC., - Scraped Surface Heat Exchanger 01, Cooler., Pilot G&A Perfector - SSHE Cooler Perfector 57 is designed for lenient cooling of medium viscosity, pumpable food like margarine. Gerstenberg & Agger A/S, type Perfector Lab 1x57, serial number 12910, year 1993, dut ...

This Anthracene and Carbazole Purification Plant is a complete industrial rectification and crystallisation system for the production of purified carbazole and anthracene from crude anthracene.The plant offers high-purity output with a design capacity of 2,600 tonnes per year of carbazole and 3,600 tonnes per year of anthracene, making it a proven solution for buyers of used chemical purification equipment. Manufacturer: NJR Type of Machine: Anthracene and Carbazole Purification Plant Design Capacity: - 2,600 t/a Carbazole - 3,600 t/a Anthracene Output Quality: - Purity of Carbazole: greater than 97.0% - Purity of Anthracene: greater than 95.5% Production Process — Three Steps: - Step 1: Crystallisation - Step 2: Rectification - Step 3: Solidification (Granulation) Process Description: - Crystallisation: Static layer crystallisation, 3-stage process. Cooling plates suspended  ...

The Tetra Pak Almix - Scanima Pilot Plant Mixer SPM-100 is a versatile vacuum processing system designed for pilot plants, product development and small-scale industrial production. It combines vacuum mixing, powder induction, high-shear homogenisation, heating, cooling and automated recipe control into one compact unit, making it ideal for producing a wide range of dairy, beverage and food products.The mixer is equipped with an integrated vacuum system that creates a controlled vacuum inside the vessel before and during processing. Operating under vacuum significantly improves powder incorporation by eliminating air, reducing foam formation and preventing oxidation. Powders such as milk powder, proteins, starches, sugar, cocoa, stabilisers and emulsifiers are drawn directly into the liquid through the integrated powder funnel, ensuring rapid wetting and lump-free dispersion while minimi ...

General SKU226Y116 MakeYstral SerialY-PS 638134 TypeYstral Process System Pressure Working pressure4 Bar Vacuum possiblecheck Working pressure jacket6 Bar Vacuum possible jacketcheck Main Features MaterialStainless steel Volume1200 Ltr. Motor35 KW Specified Features - Processing vessel Closed stirring vesselcheck Capacity400 l. (580 l.) Vessel sizesø 880 x 1320 mm Dished bottomcheck Dished top sidecheck With jacket45 l. Max. temperature140 °C, Jacket: 180 °C With paddle stirrerHydrolysis stirrer Motor4 kW Speed mixing shaft7—84 rpm With homogeniserConti-TDS Motor22 kW, 300—3600 rpm MaterialStainless steel 1.4404 (316L), Stainless steel 1.4435 (316L), Stainless steel 1.4571 (316Ti) With jacketcheck General Year of construction2009 LocationBarneveld With switchgear(as is) Floorspace5,40 x 5,00 m Total height3,60 m Weight7000 kg CEcheck Extra Spe ...

General SKU226Y118 MakeGEA Wiegand Serial354320.90-1 Main Features MaterialStainless steel Specified Features - Miscellaneous filter MaterialStainless steel 1.4404 (316L), Stainless steel 1.4571 (316Ti) General Year of construction2015 LocationBarneveld Floor space3,19 x 1,27 m Total height1,92 m Weight800 Extra SpecificationsMain components—&:nbsp:One sanitary process/buffer tank (524 L, unpressurized, closed design, with cooling jacket, spray ball for CIP, DN200 hand-hole), with magnetic stirrer, 0,55kW, 400V, 369rpm— One closed-loop RO membrane unit, product-contact parts in stainless 1.4404— Feed pump, 200 µm edge-gap strainer, tube-bundle heat exchanger (loop cooler), one 3838 membrane housing, control and sampling valves, safety/relief valveFlow rates—&:nbsp:Feed pump (41P01): max 1,200 L/h (~1.2 m³/h at 55 bar)— Loop pump (01P01): max 15,000 L/hPressure  ...

Manufacturer: Scheugenpflug Type of machine: Casting and potting plant line Year of manufacture: Individual components dated 2022 and 2023. Operating history: The system was in operation from approximately August 2022 until the end of 2023 and ran without problems until the line was shut down The line is composed of the following main components. 1. Potting cell with axle system - Type: CNCell - Built in 2022 - Air pressure: 6 bar - Power supply: 400V 3~/N/PE. - Power frequency: 50/60 Hz - Power input: 8.6 kVA - Rated current: 13.8 A - Control voltage: 24 V DC 2. PTS preheating oven - two lanes - Type: FC Curing Oven FC-5Z-57-P-2S-6050-100 - Year of construction: 2022. - Nominal temperature: 100 degrees Celsius - Throughput time can be individually adjusted. 3. Barrel stirring station - Type: Barrel Agitator Station - Built in 2023 - Weight: 800 kg - Air pressure: 6 bar - Power ...

Concrete batching plant 100-120m3/h MIXING SET. FTS 4000 / 3000 horizontal double shaft mixer. (Sicoma, Italy) SET OF 4 HOPPERS AGGREGATE LIFT SYSTEM. Aggregate elevator belt to mixer. Length: 12,100 mm. Band width: 800 mm. Cement weighing scale with a load capacity of 1,500 kg. Construction in 3 mm thick steel sheet. Weighing system using 3 load cells. WEIGHING AND DOSING OF WATER. Weighing scale with a load capacity of 750 liters. Steel sheet construction. Weighing system using 3 load cells. POWER AND CONTROL PANEL. Watertight cabinet to be located in a dosing booth. Automatic operation. Equipped with SIEMENS electrical mechanisms. COMPUTER SYSTEM FOR AUTOMATION AND MANAGEMENT OF CONCRETE BATCHING PLANT DRY MIX/WET MIX. Dynamic control of production flows. Automatic activation of vibrators and fluidisers. Weight safety control in scales. Dynamic cycle corre ...

General SKU214X079 MakeUnknown TypeUnknown No.Unknown Year of constructionUnknown LocationBarneveld Main Features Motor1.5 KW Width350 mm Specified Features - Mixing mill Motor1,5 kW, 380 volt, 1410 rpm Mill width350 mm Mill diametre110 mm With variator3-36 rpm With temperature control20-270°C Electrical heatingcheck With jacketcheck General With switchgearcheck Floorspace1,50x0,60 m Total height1,80 m Weight570 kg Extra SpecificationsTesting Roll mill, Roll diameter 110 mm, roll face width 350 mm, operating width 265 mm, nip width 0,1-5 mm&:nbsp:Mixing millsRubber-Plastic machinery > Mixing millsIndustries > Chemical > RubberBrand > - What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Pl ...

General SKU296U565 MakeWAB-Bachhofen LocationBarneveld TypeKD 45 Main Features MaterialStainless steel Volume45 Ltr. Motor33 KW Specified Features - Sand mill Horizontal sand millcheck Capacity45 Ltr. Housing dimensions Dia: 290x750 InletDia: 30mm OutletDia: 30mm With mechanical sealcheck With jacketcheck Motor33 kW, 380Volt,985rpm (EX) Rotor speed985rpm With ballscheck CapacityCap. range 180-1000 l/h With pumpPonndorf, PX15 Motorcheck Materialstainless steel 1.4721(heat resistant), Stainless steel 1.4306 (304L) With jacketcheck General No.760735 Year of construction1976 With switchgear(as is) Floorspace1,4x1,0 m Total height1,8 m Weight1200 kg ATEX designedcheckPaints & coatingsStarchCatalysts & fillersDetergent & surf.CosmeticsFood additivesSugarSand millsConfectioneryDyes & pigmentsMinerals & inorganicWab BachofenIndustries > Chemical > Paints & coatin ...

General SKU296U567 MakeDYNO-MILL WAB Bachofen LocationBarneveld TypeKD 60 Main Features MaterialMild steel/Stainless steel Volume60 Ltr. Motor45 KW Specified Features - Sand mill Horizontal sand millcheck Capacity60 Ltr. Housing dimensions Dia: 290x960mm InletDia: 30mm OutletDia: 30mm With mechanical sealcheck With jacketcheck Motor45 kW, 350/660Volt, 1475rpm Rotor speed900rpm Without ballscheck Capacitycap. range 200-1300 l/h With pumpcheck Motor0,37kW,230/400Volt, 1375rpm MaterialMild steel, stainless steel 1.4000 (aisi 429) With jacketcheck General No.910820 Year of construction1991 Floorspace2,1x1,3 m Total height1,8 m Weight1500 kgPaints & coatingsStarchCatalysts & fillersDetergent & surf.CosmeticsFood additivesSugarSand millsConfectioneryDyes & pigmentsMinerals & inorganicWab BachofenIndustries > Chemical > Paints & coatingsIndustries > Food & Feed >  ...

General SKU291Y514 MakeFryma TypeML180 Year of constructionunknown Main Features MaterialStainless steel Motor11 KW Inlet diameter30 mm Specified Features - Colloid mill Colloid millcheck Rotor sizesø 180 x 28 mm Teethed rotorcheck With hoppercheck Inletø 30 mm Outlet200 x 60 mm Motor± 11 kW, (380 V) MaterialBrass, Stainless steel 1.4408 General LocationBarneveld Floorspace0,5 x 0,7 m Total height1,15 m Weight220 kg Extra SpecificationsThroughput range 1,000–12,000 L/hr.&:nbsp:Achievable particle size 0.5–5 mm.&:nbsp:Oils & fatPaints & coatingsGeneric medicinesOintmentsBiotechnologyColloid millsFeed additivesDetergent & surf.CosmeticsFood additivesLubricants & oleoDairyConfectioneryBeveragesBiopharmaceuticalNew arrivalsMinerals & inorganicFrymaIndustries > Food & Feed > Oils & fatIndustries > Chemical > Paints & coatingsIndustries > Pharmaceutical > Generic ...

General SKU291Y527 LocationBarneveld MakeKarl Schnell Type062-F282-248 Motor Motor power21 kiloWatt Main Features MaterialAluminium/Stainless steel Motor21 KW Inlet diameter200 mm Specified Features - Colloid mill Colloid millcheck Rotor sizesø 240 x 155 mm With hoppercheck Inletø 200 mm Outlet185 x 75 mm Motor21 kW (380 V, 2880 rpm) Speed2880 rpm Material1.0257 St 44.4, Stainless steel 1.4305 (303) General No.Unknown Year of constructionUnknown With switchgear(as is) Floorspace0,6 x 0,9 m Total height1,7 m Weight500 kgOils & fatPaints & coatingsGeneric medicinesOintmentsBiotechnologyColloid millsFeed additivesDetergent & surf.CosmeticsFood additivesLubricants & oleoDairyConfectioneryBeveragesBiopharmaceuticalNew arrivalsMinerals & inorganicKarl SchnellIndustries > Food & Feed > Oils & fatIndustries > Chemical > Paints & coatingsIndustries > Pharmaceutical >  ...

General SKU291Y475 MakeKarl Schnell Serial42942 Motor Motor power55 kiloWatt Main Features MaterialStainless steel Motor55 KW Inlet diameter165 mm Specified Features - Colloid mill Colloid millcheck Rotor sizesø 220 x 50 mm With hoppercheck Inletø 165 mm Outletø 100 mm Motor55 kW (400 V 2880 rpm) Materialstainless steel 1.4006 (AISI 410) General Type080 F248 Mounted on framecheck LocationBarneveld Floorspace1,15 x 1,00 m Total height1,55 m Weight700 kg Extra SpecificationsWithout perforated disc.Oils & fatPaints & coatingsGeneric medicinesOintmentsBiotechnologyColloid millsFeed additivesDetergent & surf.CosmeticsFood additivesLubricants & oleoDairyConfectioneryBeveragesBiopharmaceuticalNew arrivalsMinerals & inorganicKarl SchnellIndustries > Food & Feed > Oils & fatIndustries > Chemical > Paints & coatingsIndustries > Pharmaceutical > Generic medicinesIndustr ...

Qty. 1 Second-hand foil rolling mill plant Mfc.: World Co. (Japan) Type: 6-Hi – Non reversing mill Built: 2002 Application: Copper foil Width: 400 – 700 mm Coil weight: Max. 5 Ton Thickness Entry: 100 – 200 microns Exit: 5 – 100 microns Speed: 0-400/800 m/min. Thickness X-Ray unit AGC system Variable Crown Control Hydraulic servo equipment Main motor power: 200 kW DC Slitter line Mfc.: IHI Width: 150-700 mm Thickness 5 – 50 microns Degreasing line Mfc.: World Co. Strip width: 700 mm Thickness: 10-50 µm Treatment line Mfc.: Kawasaki Built: 2005 Width: 700 mm Thickness: 10-50 µm

Stock # U2267-2 Second hand stainless steel contact parts (316Ti) sand mill by Drais (Germany) model Perl-mill PMC 12.5 TEX. Machine has total volume of milling chamber 17.2 l and working volume about 12 l. Mill has rotor with plastic rings and works with rotation speed up to 1450 rpm. Machine is driven via belt gearbox by electric motor 13.5 kW, 1500 rpm, 400 V, 50 hz, Eex eIIT3 design. Mill is equipped with feeding pump, filter and electric cabinet. Includes technical documentation. Machine new 2002.

1 x NEW 'Bainite' (India) Make 1000mm (42in) wide x 400mm (16in) dia two roll mill, Hydraulic nip adjustment (dual acting cylinders), Peripherally drilled chilled cast iron rolls (Hardness 65/72 Shore), with anti friction roller bearings, Friction ratio 1:1.08, Hinged guide plates, Lubrication system comprising pneumatic intensifier with grease reservoir, Electro pneumatic brake with power fail safe mechanism. Safety bars fitted to front and rear. Compact right angle drive with 45kW Siemens AC variable speed squirrel cage motor through heavy duty helical design direct drive reduction gearbox (SF 2), Back roll speed 18rpm/front roll 16.6rpm. All mounted on a compact design fabricated steel bedplate. Stainless steel tray underneath. Including electrical controls comprising Siemens G130 VFD drive and S7-1200 plc with HMI. CE marked, with full Technical file, Documentation and S ...

REVAMPED: 1990, WIDTH: 700-1400 MM, THICKNESS: 100 MICRONS - EXIT: 2 x 5 MICRONS 1500 M/MIN.,

GINES, Barcelona 800mm wide x 350mm dia two roll mill, Machine number: 88, manual nip adjustment, adjustable guide plates, friction ratio 1:1.18, direct drive gearbox (on left hand side), with 60HP DC variable speed motor, Mentor II DC drive control panel. O/a dimensions 2750mm x 2100mm.

5 axis machininng center (milling/turning from bar) multitasking Under power in our warehouse MAKE CHIRON MODEL MILL 800 5 axis CNC Fanuc 18iMBS (5 simoultaneous axis 1) X, Y, Z (mm) 800 ? 500 - 550 Rapids (Highspeed) 60 m/min Swivelling head CNC controlled (B axis) +/- 100° Turning spindle Peiseler Milling spindle 12.000 giri / 140 Nm (v nota 2) Tools 65 Tool type HSK-A 63 DIN 69893 Tool-change time 1,5 sec (v nota 3) Table 1400x500 Max table load 1200 kgs Coolant through spindle 70 bar (see note 4) CNC controlled clamping/rotating unit for 6th face machining (v. nota 5) Pressurised linear encoders Swarf conveyor Renishaw-ready Y.O.M. 2006 Weight 7500 kgs Turning package Max dia 65mm RPM: 15 / 4500 Max 42,5 KW / 90 Nm. Hydraulic clamping 800 Nm. Bar loader ILS-RBK- 10012 65 Diameters min ...

Reed 42" x 16" Two Roll Mill. 40HP Motor, with clutch brake. Friction ratio 1.1 Manual Nips. On one-piece steel bedplate.

Hammer mill Manufacturer: NEUE HERBOLD Type HM 450/300 Working width: 300 mm Rotor width: 450 mm Drive: 18.5 kW -NEW MACHINE- size reduction of brittle plastics like electronic scrap, wood scrap, and organic insulation material.

EUROLUX Fruit and vegetable mill with grinding ring Delivery date: approx. 6-8 working weeks/ by appointment Description of the machine: With this mill system it is possible to shred a wide variety of raw materials, adapted to the pressing system and the degree of maturity. The raw material is placed in the funnel of the mill. There is a screw in the hopper that conveys the raw material to the grinder. The raw material is crushed in the grinder and laterally conveyed out of the grinder. Depending on the material to be ground, different knives and grinding rings can be used. You can also change the grinding degree through the speed. If necessary, it is possible to overlay the grinding with inert gas The system can be easily opened and pulled apart for cleaning. The mill is completely assembled and wired on a frame. Two lip seals are installed to seal the grinder on t ...

Qty. 1 Second-hand skin pass mill Mfc.: Mannesmann Demag Sack Built: 1980’s Modernised in 1986 & 1993 Type: Duo Cold Rolling Mill – Non-Rev. Dia. 330 x 500 mm Material: Carbon steel, cold rolled and annealed Strip width: 80 - 470 mm Thickness entry: 4.0 mm Exit: 0.2 mm Decoiler Modernised in 1986 ID: 400 with segments 500 & 600 mm Spreading range: 370 – 420 mm Strip tension: 1300 – 65 daN Braking system: Generator Braking torque: max. 1300 daNm De-coiling speed: 2.5 m/sec. Coil cross section: 20 – 1880 mm² Coil weight per mm strip width max.: 10 kg Coil weight: 5.0 T Coil ID: 400 & 500 mm Coil OD: 600 – 1400 mm Roll dia.: 300 – 330 mm Roll length: 500 mm Roll force: 1850 – 2400 kN Min. roll force: 150 kN Hydraulic roll adjustment Adjustment stroke: 80 mm Adjustment speed: 1 – 3 mm/sec. Rolling speed: 2.5 m/sec. (150 m/min.) PLC system: ...

Qty 1 x Shaw 60in x 22in two roll mill, Manual nip adjustment, Peripherally drilled rolls (front and back), Hinged guide plates, Sleeve bearings with motorised lubrication, Right angle drive gearbox with 115Kw DC variable speed motor, All mounted on a heavy duty bedplate. Carter stockblender mounted on too. Complete with controls etc and in very good condition.

1 x Heavy duty 2 roll mill Roll dimensions: 2100mm x 665mm dia. Hydraulic nip adjustment, Safety push bars, Peripherally drilled rolls, Sleeve bearings with grease lubrication, Right angle drive gearbox, with Siemens 240kW DC variable speed motor, Strip knives fitted to front roll, Heavy duty fabricated bedplate, Carter stockblender mounted on top.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Manual nip adjustment, peripherally drilled rolls, Unidrive gearbox with flexible couplings, single 106kW DC variable speed motor. Very good condition.

Qty 1 x Schwabenthan 200mm dia x 450mm wide two roll mill, Manual nip adjustment, Digital nip gap readout, Electrically heated rolls, Jahnel gearbox with 10HP motor to each roll (variable speed), Variable friction ratio/roll speeds, Stainless steel interlocked guards and tray. Complete with electrical controls and in good condition. O/a dimensions 2700 x 1500mm

Qty 1 x Schwabenthan 150mm dia x 350mm wide two roll mill, Manual nip adjustment, Digital nip gap readout, Electrically heated rolls, Even/friction selectable gear ratios, Motor mounted under frame. Complete with electrical controls and in good condition. O/a dimensions 2400 x 850mm.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, FULL Unidrive gearbox with flexible coupling, 2 x 68kW DC variable speed motors. Variable friction ratio/roll speeds. In very good condition.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, Unidrive gearbox with flexible couplings, single 138kW fixed speed motor. Fixed friction/roll speed. In very good condition.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, FULL Unidrive gearbox with flexible couplings, 2 x DC variable speed motors. Variable friction ratio and roll speed. In very good condition.

Ideal for passage driving with consistent efficiency and for achieving the narrowest grain size distributions in the micrometer range, Maximum operational safety: even the basic version is designed in accordance with the explosion protection directive for installation in ATEX Zone 1 (ExII 2 G cb IIB T3) Grinding media sizes from 0.5–2.5 mm diameter Ideal cooling properties: The forced routing of the cooling water in the outer jacket allows the processing of temperature-sensitive productsEasy handling – each DYNO-MILL® KD can be dismantled in just a few simple steps Easy operation and adjustment of operating parameters Easy handling – any DYNO-MILL® KD can be dismantled in just a few simple steps Easy operation and adjustment of operating parameters Grinding tank : 50 litres Power : 45 kW Voltage : 380 V Weight : 1050kg

Milling machine 4-axis (15995740874) DMG Milltap 700 (2015) Spindle 24,000 1/min NC parts apparatus Lehmann EA-510. L Tool magazine 25 places Renishaw Measurement Kit Rinsing gun Milling machine 5-axis (15995747284) DMG Milltap 700 (2015) Spindle 24,000 1/min Swivel rotary tables 5-axis simultaneous operation Clamping pneumatics 1-circuit Tool magazine 25 places 40 bar IKZ Conveyor Rinsing gun Renishaw Measurement Kit Milling machine 5-axis (15995765944) DMG Milltap 700 (2018) Spindle 10,000 1/min Swivel rotary tables 5-axis simultaneous operation Clamping pneumatics 1-circuit Tool magazine 25 places 40 bar IKZ Conveyor Renishaw Measurement Kit Automatic front door Automation interface including automation door on the right Milling machine 5-axis (15995734744) + WH3 (770200062R) DMG Milltap 700 (2014) Spindle 10,000 1/min Swivel rotary  ...

Various millstones

Two Roll Mill 1m wide Hydraulic Nips With motor and gearbox AEG motor, 380volts, 107amps, 55kw, 1475rpm, 50 cycles Unidrive Gearbox manuf: Santasalo, Type 3KSV70, Year 1977, Weight 1500kg Lunn Safety gear fitted front and back of Mill Complete with control panel All mounted on a one piece bedplate Compact

5 axis machininng center (milling/turning from bar) multitasking Under power in our warehouse MAKE CHIRON MODEL MILL 800 5 axis CNC Fanuc 18iMBS (5 simoultaneous axis 1) X, Y, Z (mm) 800 ? 500 - 550 Rapids (Highspeed) 60 m/min Swivelling head CNC controlled (B axis) +/- 100° Turning spindle Peiseler Milling spindle 12.000 giri / 140 Nm (v nota 2) Tools 65 Tool type HSK-A 63 DIN 69893 Tool-change time 1,5 sec (v nota 3) Table 1400x500 Max table load 1200 kgs Coolant through spindle 70 bar (see note 4) CNC controlled clamping/rotating unit for 6th face machining (v. nota 5) Pressurised linear encoders Swarf conveyor Renishaw-ready Y.O.M. 2006 Weight 7500 kgs Turning package Max dia 65mm RPM: 15 / 4500 Max 42,5 KW / 90 Nm. Hydraulic clamping 800 Nm. Bar loader ILS-RBK- 10012 65 Diameters min ...

KAAST Millex VPlus 7 CNC machining Centre way back in 2011 complete with Siemens Controller 802S

- workpiece diameter d680 - max workpiece length 3400 mm - max working lengths 2600 mm - with discs (d1100 mm) - required electric capacity 60 kW/h - under power, in use

Bead mills Manufacturer: Bachofen AG (CH) Type: Dyno-Mill KDL-Pilot 3 items on stock No.: 1) 910969; 2) 860739; 3) 840338 Power: 3.3 kW in Eex protectioin very good condition with various spare parts LWH: 650 x 500 x 500 mm

Laboratory bead mill Manufacturer: Bachofen AG Type: KDL No.: 920235 Power: 1.85 kW in explosion protection shear tools in ceramic very good condition with various tools and spare parts LBH mill: 650 x 650 x 520 mm LBH box: 600 x 400 x 430 mm

Drive : 75 KW Dimensions : L 3800 mm x W 1600 mm x H 2200 mm Weight : 3900 kg.

Drive : 110 KW Dimensions : L 2500 mm x W 1300 mm x H 1800 mm Weight : 2800 kg

Qty.1 Second-hand milling (scalping) line Mfc.: Torrington Type: 30" Slab Miller Strip width: 30” – 762 mm Cutter Speed: 500 rpm Metal speed: 18 fpm (1.9 m/min.)) Capacity: min. ¼” max. 1-1/4” Thickness Entry thickness range: 13 – 20 mm

Key data: 190 mm, 450 mm

available Lab Mill! Description attached !

Exchange units for contour milling HOMAG

Key data: 150 mm, 300 mm

Two Roll Rubber Mixing Laboratory Mill Manuf.: JRD Bipel 300mm x 150mm rolls Roller type bearings Nip fully guarded Motorised nip adjustment Roller speed variable up to 32 rpm Friction ratio 12:1 Grease lubrication Roller reverse system

Key data: 500 mm, 200 mm

Drilling / Milling machine OPTIMUM type OPTI F 40 E Travel X: 500 mm Travel Y: 200 mm Spindle: Ø 80 mm Cone CM3 Spindle exit: 120 mm Spindle speed: from 95 to 3200 RPM Table size: Length 730 mm x Width 210 mm 2 speeds motor Motor power: 1,5 Kw Straight head Cross table Manual Descent Equipped with: 1 rotary vice Voltage: 380 V Dimensions (L x W x H): 1200 x 900 x 1400 mm Weight: approx 350 KG

GeneralHighly productive compact machining centres; Control: Siemens 840D solutionline Technical DataFeed rate longitudinal/transverse/vertical1-60000/1-60000/1-60000 mm/minRapid traverse longitudinal/transverse/vertical60/60/60 m/minWorking area 1Longitudinal700 mmCross420 mmVertical380 mmMiscellaneousClamping SystemMAS 403 - 45° Floor space/WeightDimensions (L x W x H)1,65 x 2,34 x 2,5 (1,65 x 2,95 x 2,55) mWeight approx.4100 KgSpindle speed up to 24,000 r.p.m. BT30Spindle 24,000rpm with tool taper BT30 JIS B 6339 (MAS 403-45°) AC-Motor 20 / 4 KW (max. / 100% ED) Watercooling Spindle and Spindle motor via heat exchanger (fan)TableTable surface 840 x 420 mmMaximum load (table centre) 300 KgSlot width 14 mmNumber of Slots 2Clamping grid M 12, 100 x 100 mmTool clamping for BBT 30 (Big+)Tool taper BBT 30 - Big+ Pull stud MAS 403 - 45°Tool magazine 25 placesTool magazine 25 places (suita ...