pl used for sale

; ready for use

Abegg to fan and the fan with fans Ziehl. noch nie benutzt NEW

Year issue: 2017 - new Capacity: 20,000 cph, complete stainless steel Product: energy drinks and juice Can: 250 ml. Type of can: 202/200 slim can Heating method: Steam - Plate heat exchanger in outside of pasteurizer Material: Stainless steel AISI 304 1. TECHNICAL CHARACTERISTICS OF THE PASTEURIZER Temperature of product (inlet temperature) in pasteurizer: 2? - +6? Temperature of product (outlet temperature) from pasteurizer: +27? - +30? Pasteurizing temperature: +72? - +75? Holding on pasteurizing temperature: 12.5 min Heat consumption (steam by 3-4 bar) during stable operation: 480-550 Kg/h Temperature of steam: +140? Water consumption during stable operation: 0.5 - 0.9 m3/h. Consumption of compressed air 6 bar: 500-700 nl/h Total power consumption: 30 kw Supply voltage: 3F/N/PE/A, 50Hz, Control voltage: 400 volts Degree of protection: IP-54  ...

4-side Planer SCM P 75 Year of construction 1983 Masch. No. 045 8vsoczcl8 Planing width of 180 mm Planing height of 130 mm 4 spindle length 2500 mm Weight 1670 kg L x W x h: 310 x 120 x 180 cm The machine is in good condition, little used, ready for use. Subject to changes, errors, and intermediate sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

WEINIG HYDROMAT 22 BL Year of construction 1995 with splitting unit (lamellar saw) Feeding (Automatic feeder and pull-out unit!) With safety hood and soundproof cabin! Machine specifications:  - Planning capacity 220 x 120 mm  - Feeding, 8– 80 m/min, motor 18.5 kW Spindle layout:  Bottom-right-left Top - bottom, table rigid Bottom, table rigid, spindle prepared Top - bottom, table rigid, spindle prepared Gap unit, consisting of 1 right and 1 left spindle each 30 kW (4500 rpm) incl. table roll, sliding roller, spray barrier and gap wedge removal 4 roller pull-out Special pressure and fixtures for the production of top layer slats Feeder (all-in) for slats and pull-out tape     

Planer blade sharpening machine Meinert with built-in Cabinet apparatus for gang saws weight approx. 350 kg Built in 1963 L x W x H 80 x 60 x 140 cm The machine is in good condition, ready to use. Subject to changes, errors, and intermediate sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Working width: 630 mm Working height: 3,300 mm Motor output: 7,5 kW Number of knives: 4 St. Feed speed: 7 + 14 m/min. loading dimensions L x W x H: 1070 x 1200 x 1060 mm weight: 1050 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Working width: 410 mm Length of the planing table: 2850 mm Number of knives: 4 (Tersa) St. Motor output: 5,5 kW loading dimensions L x W x H: 2950 x 1260 mm weight: 870 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Sell granulator for plastic strands of extrusion. 7,5 kW power. Sale, clearance there. If it works, I don't know, therefore the reasonable sale price.

The ZAKMET FIRECUT CNC 1325 13000 X 2500 gas plasma cutter was produced in 2011. The machine is equipped with Hypertherm EDGE'Pro digital control. The burner's working area is 13,000 mm long and 2,500 mm wide. The running elements of the cutter are lubricated with the Memolub 3.0 central lubrication system. Technical data of the plasma burner: - machine working area (L x W x H): 13,000 x 2,500 mm (additionally 700 mm) x 200 mm - maximum table load: 15 kN / m2 - machine supply voltage: 3x400V AC 50 Hz - central lubrication: Memolub 3.0 - minimum temperature of the working environment: +5 degrees C - maximum temperature of the working environment: +60 degrees C - machine dimensions (L x W x H): 14500 x 5500 x 2000 mm Plasma cutter equipment: - CNC control: Hypertherm EdgePro - ventilated section table: 1550 x 2600 mm - 9 segments - gas burner: type MS 3452 \ 250-PM (x2) - ...

surface planer , thickness planer , spindle moulder . machines SCM L'Invincibile second hand machines in Excellent working conditions NOT separate sale thickness planer model SCM S 63 l'Invincibile : useful working width mm. 630 maximum (minimum) working height mm. 240 (3) maximum removal mm. 8 variable feed speed mt./min. 6 ÷ 18 motorized table positioning with reading n.4 knives "Tersa" main motor power Hp 7,5 volt. 380/50 surface planer model SCM F52 l'Invincibile working width mm. 520 tables length mm. 3000 ground cast iron tops n.4 knives tilting guide up to 45° motor power Hp 5,5 volt. 380/50 spindle moulder with tilting spindle model SCM T160 l’Invincibile spindle tilting by electric -5 ° / + 45 ° spindle lifting by electric motor power Hp 5,5 shaft diameter mm. 50 volt. 380/50

Hand lever plate and profile steel shears heavy and stable outing cuts sheets, round steel (approx. 15mm), flat steel and T-profiles Mounted on base Special price

plansichter Buhler MPAD 6.18

Planetary grinders Manufacturer Precise In a suitcase with extensive zubehoer Rule transformer Tool holder SK40 with interchangeable tightening bolt Control range: 15000 - 45000 rpm Orbital speed 70 - 120 rpm when working horizontally max.: 70 rpm Radial delivery: 0.0001 - 0.002 mm Reception: SK40 electr. Connection: 220 V, 600 W Special price

Qty. 1 Second-hand section rolling mill plant Mfc.: Pomini, OMV, BM, Bendotti Built: 1989 continuously modernised Stopped: 2019 Installed power: 16.2 MW Billet income sizes: 120 x 120 up to 160 x 160 mm Length: 6.0 m Section production: Round bar dia.: 30 – 60 mm Angles from 30x3 up to 100x12 mm U” channel from 40x20 and 120x55 mm T” shape from 30 till 100 mm T” shape from 30 to 120 mm (Special for elevator rails- Leader in Europa) The rolling mill can be implemented with many other profiles by using different grooved rolls. Production capacity: 250,000 – 270,000 T/annum depending on the production mix Scope of supply: Reheating furnace Section rolling mill line Tying Machine Descaler Bundle Machine Cooling tower Machine shop

Three T-slot plates of a copy-fraes machine from Lid are offered. The T-slot plates can be mounted as a cross table. Scope of delivery only according to photos, without spindles. If you are interested, please request more photos. Further spare parts of lide e.g. towing table of a KF3 pre-wheels. Please ask. Special price Lid cabinet tool cabinet

1 pc flame pretreatment system with electronic control 1 pc EF 600-1 Burner control consisting of Electrical control with ignition and monitoring device for 1 pc burner, control electronics, control panel with plain text display, Emergency stop setup and interface for external control Mechanical control with Safety valves, gas/air mixers, thermoanemometrial mass flow meters for air and gas, Engine valves, pressure monitors for overpressure and vacuum monitoring and supply air blowers. 1 pcs C24-2300 Film burner, 2200 mm working width, adjustable up to min. 1000 mm with connections for water cooling and water-cooled double T-beam 1 pc spare parts consisting of 2 earth replacement electrodes and 1 replacement fabric Power supply : 400/230 V 50 Hz, 2.5 kVA Gas supply : Natural gas 75 – 100 mbar Heat output : max. 400 kW Gas consumpt ...

Many thanks for your interest in our chocolate conche plant, please find below our offer Nagema conching plant - available from south-east europe, consisting off: 2x Nagema conches 3000kg, electrical power 60 kw 1x Nagema Conches 1000 kg, electrical power 25 kw 1x Nagema Conches 1000 kg, electrical power 25 kw, missing Gearbox 1 x Conche 400kg, electrical power 12,5 kw & 1x Tank 5000kg, electrical power 7 kw Machines are installed and under electrical energie We offer this machine in 'as is' condition, ex location Bulgaria Also possible to sell single machines from this Plant. Also in as-is condition, ex location Bulgaria. 1x Nagema Conches 1000 kg, electrical power 25 kw 1x Nagema Conches 1000 kg, electrical power 25 kw, missing Gearbox 1x Nagema conches 3000kg, electrical power 60 kw: 1x Conche 400kg, electrical power 12,5 kw together with Tank 5000kg, elect ...

Qty. 1 Second-hand section rolling mill plant Mfc.: Pomini, OMV, BM, Bendotti Built: 1989 continuously modernised Stopped: 2019 Installed power: 16.2 MW Billet income sizes: 120 x 120 up to 160 x 160 mm Length: 6.0 m Section production: Round bar dia.: 30 – 60 mm Angles from 30x3 up to 100x12 mm U” channel from 40x20 and 120x55 mm T” shape from 30 till 100 mm T” shape from 30 to 120 mm (Special for elevator rails- Leader in Europa) The rolling mill can be implemented with many other profiles by using different grooved rolls. Production capacity: 250,000 – 270,000 T/annum depending on the production mix Scope of supply: Reheating furnace Section rolling mill line Tying Machine Descaler Bundle Machine Cooling tower Machine shop

Wash waw LC40 with raetzmuehle RM40 for belt presses EBP500, EBP650 and EBP820 nominal power up to 2000 kg/h engine power 6.2 (8.5) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical protection 16 A 000 mm width 700 mm Hehe 2400 mm He he Assumption 800 mm Weight 285 kg Material 1.4301 / AISI 304 Connection for cleaning 1/2 inner Connection for washingHeight mash release 1500 mm Height fruit delivery 800 mm 9mm and 12mm Cutting sieve ; New machine - best condition

The pasteurizer is available with a bottle filler or bag-in-box filling device. Nennpower l/h 180 l/h Electrical power 18 kW Electrical connection 400V 50Hz (3 phases) Electrical fuse 32 A width 440 mm Height 1580 mm Weight 43 kg material 1.4301 / AISI 304 Water content 100 l Juice supply 65 l 2 bottle filling valves or filling device for bag in box ; New machine - best condition

PLC for Desma presses

Included in delivery are: 01x closure lid, II choice Material color: green Material: Metal Dimensions: approx. 520x320x35 mm (LxWxH) Net weight: approx. 2,481kg Technical data for the closure lid: Manufacturer: SSI Schäfer Type designation: VD-14/6-A 4 closure tabs suitable for: SSI Schäfer 14/6-A General information about the article: This item is offered for pickup only. A desired transport beyond that or a dispatch of this article is associated with additional costs, which separately depending on the place of delivery or scope of delivery can be queried from us. Our services at a glance: (Prices on request) Assembly, assembly our general assembly conditions must be observed Shelf inspection Shelf inspection according to DIN EN 15635 carried out according to the Requirements of BGR 234 Visual inspection for all shelving systems Delivery with our own  ...

two different models available: PA300E = electric pasteur with tube heat exchanger. PA300EA = electric pasteur with tube heat exchanger and automatic temperature control. Rated power l/h 300 l/h Electrical power 27 kW Electrical connection 400V 50Hz (3 phases) Electrical fuse min. 40 A Laenge 750 mm width 500 mm He he 1150 mm Weight 100 kg material 1.4301 / AISI 304 Water content 35 l ; New machine - best condition

Pasteurizing system with Roehrenwaerme exchanger nominal power l/h 600 l/h power heating heater / oil boiler 55 kW Electrical power 1.1 kW Electrical connection 230V 50Hz (1 phase) Electrical fuse 16 A Laenge 1400 mm width 900 mm Height 1850 mm weight 330 / 430 kg Oil consumption 6 kg/hr ; New machine - best condition

Qty. 1 Second-hand roughing, finishing mills and special equipment Mfc.: DAVY, TMEIC, TOSHIBA, MITSUBISHI Type: 4-Hi Rev. Built: 1997 Revamped & Installed: 2008, 2011 Stopped in 7-2017 Revamped cost of USD 151.0 Mill. from 2008 up to 2011 Finishing mill equipped with CVC Roll plus Technology System Finishing mill – new hydraulic adjustment to increase rolling force to 90 MN Roughing & Finishing mills: Technology Control System (Level 1) Process Models (Level 2) for pass schedule calculation, profile & flatness control (PFC), Pacing system & Material tracking Revamped by SMS in 2011: Roughing mill: Slipper-type Spindles Product capacity: 2,000,000 ton/year Mill capacity: 30 Plates/h Entry Material: Slab T130~300 mm x W1,200~2,200 mm x L2,350~4,000 mm Final Product: Plate T5~180 mm x W1,200~4,100 mm x L max. 25 m Application: Ship building plate & Pipe pro ...

WASHING INSTALLATION 90° One washer to washing system to clean the containers. The containers are tilted 90 degrees and transported through a washing device. The washing device consists of a housing that contains a spray device which is suitable for cold water with a pressure of 5bar. A conveyor belt to transport the containers. After washing, the containers are tilted back to horizontal position. No recycling water included. The concrete floor must be prepared to drain the water to a certain drain pit. The best option is lower the concrete floor in the area of the washer. OVERHEAD DE/STACKER For the PLC controlled movement, stacking and destacking of empty, containers with a maximum weight of 100 kg an overhead stacker/destacker is installed. The stacker/destacker can PLC controlled take up from:
-a-        The destacking position on the buffer (this is also the  ...

Pasteurizing system with Roehrenwaerme exchanger nominal power l/h 1000 l/h power heating heater / oil boiler 90 kW Electrical power 1.1 kW Electrical connection 230V 50Hz (1 phase) Electrical fuse 16 A Laenge 1400 mm width 900 mm Height 1850 mm Weight 350 / 430 kg Oil consumption 10 kg/hr ; New machine - best condition

For sale complete line for plastic caps, include: 1. CCM48 with moulds and CVS 2. cooling system 3. slitting machine Perfect condition. Working at moment. Origin Italy.

Pasteurizing system with Roehrenwaerme exchanger nominal power l/h 1500 l/h power heating heater / oil boiler 140 kW Electrical power 1.8 kW Electrical connection 230V 50Hz (1 phase) Electrical fuse 16 A Laenge 1715 mm width 900 mm He 1900 mm weight 500 / 600 kg Gas consumption flu vinegar gas 11 kg/hr Gas consumption natural gas 15 m3/hr. ; New machine - best condition

750 MW each, UNUSED Gas Based Complete Combined Cycle Power Plants 2 units available Technical Specifications: The Project Details: 1. EACH module has two Gas turbines GE 9FA.03 (DLN2+) and one Steam turbine GE D11. Each GT exhaust is directed to the triple pressure unfired, natural circulation horizontal, type CMI USA HRSG. This configuration helps turndown operation of station up to 45%. 2. The Station is based on robust design of GE Gas Turbine with high efficiency DLN2+ Dry low Nox system, each GT is site rated for an output of 235 MW and the triple pressure reheat GE D11 Steam Turbine with downstream Exhaust, is site rated at 266 MW. The HRSG is a Triple pressure, Natural circulation, Horizontal design type with Deaerator atop the LP drum. Thus Net Combined cycle efficiency at Site condition is approx 57% on LHV basis. The inherent design of the gas turbine reduced the N ...

Pasteurizing system with Roehrenwaerme exchanger nominal power l/h 2000 l/h power heating heater / oil boiler 180 kW Electrical power 1.8 kW Electrical connection 230V 5 0Hz (1 phase) Electrical fuse 16 A Laenge 1715 mm width 900 mm He 1900 mm Weight 492 / 600 kg Oil consumption 19 kg/hr ; New machine - best condition

Built in 1998 Size max 205 x 130 x 30 mm min 35 x 50 mm Product weight max 1-300 g/qm Speed max up to 200 c/min; working condition

Thyssen measuring plate / control plate made of natural hard rock Thyssen measuring plate made of hard rock (granite slab) Length: 2750 mm Width: 700 mm Thickness: 200 mm Total height with table: 1200 mm Height vertical plate: 240 mm Thickness: 200 mm 2 x T-groove Flatness tolerance according to DIN 876/0 Base with cabinet Trimos HGL 2000 length measuring instrument without measured value display Item location: 42859 Remscheid Dismantling and transport by the buyer. The dismantling, loading, as well as transport can alternatively be offered by us. More measuring plates in other sizes - new and used - can be found in our shop! International shipping costs on request!

Pasteurizing system with Roehrenwaerme exchanger nominal power l/h 500 l/h power heating heater / oil boiler 45 kW Electrical power 1.1 kW Electrical connection 230V 50Hz (1 phase) Electrical fuse 16 A Laenge 1400 mm width 900 mm Height 1850 mm weight 330 / 430 kg Gas consumption flu vinegar gas 4 kg/hr Gas consumption natural gas 5 m3/hr. ; New machine - best condition

7.2MW diesel power plant. This vintage power plant has been used as an emergency generating sets for a larger R&D center in Korea, a very short actual running hours (abt. 2000~3000hrs) and has been well maintained, so our company can confidently recommend this power plant to anyone who needs it. The plant was dismantled and has been now stored in our factory and will be delivered to the buyer after the performance verification test of the generating sets at our test shop. Main Specifications - Engine Model: SSANGYONG-MAN 18V28/32H x 2 Sets - Manufactured & Running Hours: in 1999 & abt. 2000~3000hrs - Continuous Output: 3600kW x 720 rpm - Frequency & Voltage: 60Hz & 6600V - Fuel Oil: Diesel Oil / Heavy Fuel Oil - Plant Auxiliary Equipment: 1 set

Rated power: up to 400 l/h (80C pasteurtemp., 10C input temp. Juice) Thermal power: approx. 35 kW Electrical power: 1.4 kW Electrical connection: 230V 50Hz (1 phase) Electrical fuse: 16 A Laenge: 910 mm Width: 960 mm Height: 1850 mm weightweight (heating circuit emptied):260 kg weight (heating circuit filled): 360 kg Heating heater consumption: approx. 3.5 liters/h exhaust gas connection: 150mm Max. Exhaust temperature: 180C sound power level (LW, A): 83dB; New machine - top condition

Bag-in-box filling - also with 6-digit row filler available nominal power l/h 750 (at 10l bags) l/h Electrical connection 230V 50Hz (single-phase) Electrical fuse 16 A Laenge 1030 mm Width 7 40 mm Height 1065 mm Weight 85 kg material 1.4301 / AISI 304 Filling accuracy of 0.5% compressed air connection 6 bar connection for juice supply 21.3 Juice storage capacity 58 l Supplied incl. cleaning adapter ; New machine - best condition

New machine with 3 x 800 ltr. Tanks Heating system: with steam through heat exchanger The whole system is disigned to enalbe sterilzation and cleaning of filler without disassembly of parts or components Technical data: - Output pressure: 4 bar - Temperature of feed water: 15-20oC - Steam Pressure: 3 bar - Steam flow: 300 kg/h - Temperature of steam: 120-130C - Pressure of air: 6 bar - Installed electrical power: 4 kW

Measuring table 800 x 1,000 mm

Weibert form7 52 digital Dressing thickness Planer Planing width 520 mm Tersa 4 drum Dressing table length 2250 mm Planing stroke 1500 mm 90 °-45 ° Machine cast iron tables 7 KW (9,5 HP) 400V 50 HZ Thicknessing table 850x520mm Passage of 3 / 240mm Electrical height adjustment of the Thicknesser table 4 speeds 5 / 8 / 12 / 18 m / min Dual opening system of the tables to the rear Max depth of cut 5 mm Speed 5000 min/1 1-suction port 120 mm Weight approx. 700 kg G & PIECES 5503511

l 45 kw POWER 680 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 45 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw

Planetary mixer with infused tool, 2 mixing stars, 4 mixing buckets and scraper / emptying bucket. Maximum filling per batch: 2,250 l. / 3,600 kg, solid concrete output per batch: 1,500 l., workable grain size: 0 - 65 mm, with double-sided swivel valve outlet (hydraulicact). Incl. main drive motor 75 kW and many spare parts.

Plansifter MIAG LM 655-155- Maize run, six passages, cleaned Broken frame inserts have been repaired. Good working condition. We also offer a similar machine with nine passages.

Planetary mixer Varimixer AR10 The AR series of beaters is the oldest by design and also the most durable series of beaters. The AR series is characterised by the fact that it has a mechanical belt transmission with simultaneous infinitely variable speed control.  The well-known robustness and powerful motor have been retained, and a number of characteristic features of the AR models have been improved without compromising the widely recognised quality. Technical data: Capacity: 10 litres, Adjustable speed: 53-294 rpm, Stainless steel mixing bowl, Stainless steel butterfly, Electrical power: 400 V - 0,37 kW. After general refurbishment. Call and arrange a demonstration of the machine!

Magnetic plates for letterpress; 3x A4 available (format 306x217x22mm); 3x A5 available (format 217x153x22mm); 6x A6 available (format 153x108x22mm).; Ready. At this point we allow ourselves to note that all offered machines are in our unrestricted possession or access and are present in our warehouse. Visits and demonstrations are possible on request in our premises. We would also be pleased to inform you about our complete stock, as only part of our portfolio is presented here.