pin used for sale

Flange mounting, driving flange -Chuck flange with: driving pin -Outer: Ø 325 mm -Cone diameter: 139 mm -Weight: 20 kg

Single Stand - Eccentric Press PELS - RICHTER Type PEKR 125 Masch. No. 20684 Year of construction 1967 Compressive force 125 ton. Projection 430 mm Table size 1100 x 750 mm Ram surface 890 x 650 mm Table opening 400 mm Stroke adjustment 6 to 115 mm Ram adjustment 100 mm Installation height largest stroke above max. 450 mm Clamping pin bore 50 mm Stroke rate 60 strokes/min. Table height above corridor 900 mm Motor power 7.5 kW Mains connection 380 volts, 50 Hz - Overload protection by crushing plate in the plunger - Compressed air Clutch-brake combination DESCH- Plunge weight compensation cylinder - Manual ram position - Two-hand operation - Cam switchgear - Grease central lubrication Vögele - Stroke counter Space requirement L x W x H 2300 x 1450 x 3030 mm Weight approx. 10 ton. good condition; used

Flange mounting, driving flange -Chuck flange with: driving pin -Outer: Ø 260 mm -Cone diameter: 106 mm -Weight: 11 kg

Flange mounting, driving flange -Chuck flange with: driving pin -Outer: Ø 250 mm -Cone diameter: 140 mm -Weight: 13 kg

Connector, plug, sensor module, G2 flat module -4-pin -Number: 10 pieces -Price: complete -Weight: 0.1 kg

Single stand - hydraulic press SCHULZ type SES 250 Masch.Nr. 04.86.3511/3 Year of construction 1986 Compressive force 25 ton. Retraction force 10 to radius 360 mm Table surface 600 x 720 mm Ram surface 500 x 500 mm Diarrhoea opening in the table 100 mm Clamping pin hole 40 mm Ram stroke 400 mm Installation height max. 600 mm Table height above corridor 935 / 775 mm Tank capacity Hydraulic 380 litres Drive power 7.5 kW Mains connection 380 volts, 50 Hz - Fixed stop adjustment in press cylinder 180 mm- SICK photoelectric sensor - 2-hand operation - Substructure made of 160 mm U-steel Space requirement L x W x H 1900 x 1300 x 3100 / 3260 mm Weight 3.6 ton. good condition; used

Single Stand - Eccentric Press MÜLLER GEFREES Type PDET 5 S/EK Masch. No. Year of construction 1988 Compressive force 5 ton. Projection 125 mm Stand passage 170 mm Table surface 280 x 220 mm Waste hole 90mm Ram surface 160 x 100 mm Stroke adjustment 4 to 40 mm Ram adjustment 30 mm Installation height largest stroke top max. 210 mm Stroke rate 200 strokes/min. Clamping pin bore 25 mm Table height above corridor 900 mm Motor power 0.55 kW Mains connection 380 Volt, 50 Hz - pneumatic clutch-brake combination - electric foot switches - Control cabinet on the machine Space requirement L x W x H 900 x 600 x 1700 mm Weight 530 kg very good condition; used

KrausMaffei-150 clamping force 1500 fixation plate size 720x710 distance between bars 500x450 mold height 300 opening stroke 600 coupling pin pneu ejector 250 ejector stroke 150 screw 50 disponible from September 2021

Pneumatic press, air press BOSCH Type 0840 002 002 Fabr. No. 041 Year of construction 1980 Compressive force 18 KN = 1.8 ton. at 5 bar 15 kN = 1.5 ton. at 4 bar 12 kN = 1.2 ton. at 3 bar 8 kN = 0.8 ton. at 2 bar 6 kN = 0.6 ton. at 1.8 bar outreach 100 mm ram stroke 70 mm Table surface 245 x 200 Ram surface 45 mm Installation height max. 235 mm Clamping pin bore 20 mm with clamping screw Compressed air requirement 5 bar - Pressing force infinitely adjustable via pressure regulator- Pneumatic cylinder with plunger height adjustable by 90 mm- pneumatic 2-hand operation - mounted on metal base with wooden plates Space requirement L x W x H 1050 x 700 x 1600 mm Weight pneumatic press 82 kg Weight with table base 140 kg good condition; used

Pin mill Netzsch Type CUM 250 Equipped with a temperature probe in the grinding chamber Year of manufacture: 1992 Engine power: 10 kilowatts Materials in contact with product: stainless steel Equipped with a safety system for the opening of the grinding chamber.

: neu : 2022 : 7267 : prompt, Zwischenverkauf v : Türkei : 12120 € : 247.25 € : 1 : 160 to : 400 mm : 900 mm : 1450 mm : 6,2 mm/s : 9.8 mm/s : 1450 x 450 mm : 5,5 kW : 1640 mm : 1000 mm : 2550 mm : 1300 kg with horizontally sliding cylinder motorhydraulic with additional hand pump Height adjustable table Oil Pressure Gauge INCL. OPTIONAL EQUIPMENT: handwheel with locking pin for cylinder adjustment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

TIG hose package, welding torch, hand welding torch, TIG torch -TIG hose package: water-cooled -Length: 7 m -Plug: 5 pin -Weight: 4.2 kg

Machine Type: Valve Terminal Manufacturer: Festo Type: GPX-GE-EV-S-7/8-4 Pin Condition: as good as new / used for testing purposes only Offer will only be sent if a complete imprint is provided! Price 1.190 Euroincl VAT and shipping within Germany Location Warstein , Germany Reference Follow DESCRIPTION We offer you a used valve terminal from the manufacturer Festo. Availability: immediately Our offer is aimed at tradespeople who are registered within the meaning of the Trade Regulation Act according to §14 GewO. The offer is subject to change, subject to prior sale. Please provide your full contact details to receive a quote with our terms and conditions and payment terms. Errors in the descriptions and offers are excepted!

Rental Hosokawa Alpine UPZ 100 cryogenic system (LN2) by Alpine Rentals. Technical details Design: Non Pressure Shock Resistant (NPSR), non ATEX Suitable for cryogenic grinding with LN2 Material of construction: stainless steel Without wear protection Batch operation, for a few kilos normally (product dependent) Scope of supply 100 UPZ system with grinding tools of choice, small feeding hopper with a dosing channel, cooling screw to feed the LN2, LN2 container, filter and barrel to collect the fines. Includes an operating panel, switch cabinet and a vacuum cleaner. LN2 to be provided on-site This small size system with an universal mill UPZ 100 can be used for the production of small batches as well as for R&D purposes. Thanks to the different grinding accessories it can be adapted to different tasks and target fineness. Suitable for the cryogenic grinding with liquid nit ...

Fully refurbished Hosokawa Alpine UPZ 100 used system by Alpine Originals. Technical details Design: Non Pressure Shock Resistant (NPSR), non ATEX, not suitable for inert operation (N2) Material of construction: stainless steel Without wear protection Batch operation, for a few kilos normally (product dependent) Scope of supply 100 UPZ system in large table fitted with pins (other grinding tools of choice could be offered for an additional price), small feeding hopper with a dosing screw, filter and barrel to collect the fines, blower and piping. Includes a relay control panel. This small size system with an universall mill UPZ 100 can be used for the production of small batches as well as for R&D purposes. Thanks to the different grinding accessories it can be adapted to different tasks and target fineness. The Hosokawa Alpine Ultraplex UPZ is a universal fine impact mil ...

Publisher's Description The machines of the new UC series (Meisterstück) from Winterhalter are state-of-the-art and set standards in terms of washing results. The one-button operation is equipped with color coding that informs the user of the condition. A progress indicator is also integrated into the display. The smart Winterhalter touch display offers three washing programs to choose from (cutlery washer has only one washing program). These can be customized. The programs are displayed in a language-neutral manner, thanks to self-explanatory images of the washware. This guarantees intuitive, error-free operation. Furthermore, additional programs such as short, energy-saving, whisper and intensive programs are available in all machine models and are easy to activate. Thanks to a large number of technical innovations, Winterhalter has succeeded in achieving washing results of u ...

ID3202 Wellco-Drill WD80 approx. 3110 hours/ hours Drilling rig, Hatz 3-cylinder diesel engine, fully hydraulic cylinder feed, flushing drill head - reinforced version, drive pin and pulling bell, rod catching device, centrifugal pump, cable winch, 4 hydraulic support cylinders, control panel, machine has been general overhauled (the control blocks have been completely renewed, the chain profile is new, the interceptor is new, the drill head has been completely overhauled, all possible wear parts have been renewed, all hydraulic components have been overhauled) Drilling rig, Hatz 3-cylinder diesel engine, fully hydraulic cylinder feed, directional drill head - reinforced design, drive journal and drawing bell, linkage interceptor, centrifugal pump, winch, 4 hydraulic support cylinders, control panel, machine has been completely overhauled (the control blocks have been completely rene ...

Automatic punching press, high speed press, eccentric press, single-column press, punching machine, single-column eccentric press. Manufacturer: Kaiser PO 10. Year of manufacture: 1982. Pressure capacity: 10 [tons]. Stroke: adjustable 2 to 40 [mm]. Speed: 120-600 [strokes/min]. Table size: 460 x 250 [mm]. Clamping pin: Ø 32 [mm]; depth 50 [mm]. Central automatic lubrication system. Connection: 380 [V]; 50 [Hz]. Manual speed adjustment on motor. Motor: Stober; 1.1 [kW]; 1450 [1/min]. Single disc clutch and brake. Dimensions: 1250/950/H1800 [mm]. Weight: 850 [kg]. El schematics included. Packing and loading included. Feeding device not included, if needed contact for more information.

Two cutting speeds - Vice with counter-clamping device - Infinitely variable mitre adjustment (-45° to +60°) - Coolant device - Material support roller - Pin chip remover and chip drawer

Bürkle Multifoiler BTF 1534 Model: 2009 - Made in Germany Full automatic pin system and rotation - 3 frames Frame sizes: 1330x3230 Maksimum working sizes: 1250x3150 Total Power: 53 kW Machine is in good condition and actively used in the production

GeneralUniversal Milling Machine; Control: CELOS with Siemens 840D sl Operate Working area 1Longitudinal650 mmCross520 mmVertical475 mmTechnical DataType of main driveAC Drive power (100% DC)16 kWDrive power (40% DC)21 kWSpeed range20 - 15000 rpmSpindle taperSK40 Tool holder DIN ISO 7388-1-A Clamping SystemDIN ISO 7388-3-A, AD Feed rate longitudinal/transverse/vertical-42000/-42000/-42000 mm/minRapid traverse longitudinal/transverse/vertical42/42/42 m/minFloor space/WeightDimensions (L x W x H)2,85 x 2,35 x 2,75 mWeight approx.7500 KgDirect measuring systemDirect path measuring systemSpindle speed 15,000 rpmMotor spindle speedMASTER® HSK-A63 Spindle speed 20 - 15,000 min-1 Output 21 kW / 16 kW (28 hp / 21.5 hp) Torque 111 Nm / 85 Nm (82 ft lbs / 63 ft lbs) (40 / 100 % duty cycle)NC swivel rotary tableSwivel Rotary Table for simultaneous machining Clamping surface dia. 630 x 500mm / 24.8 ...

The machine produces, for sale with its tools, see photo X axis: 318 millimeters Y: 51mm Z: 660mm Y +/- 50.8mm Counter spindle rotating diameter 616 mm Tool with 12 positions Pin Spindle passage 51 mm Spindle bore 88.9 mm Chuck size 210 mm Max. power 22.4 kW Main spindle speed 0-4000 rpm Max. torque 373.0 Nm at 700 rpm Spindle axis - 3.7 kW drive Machine power 30 kVA

Fully refurbished Hosokawa Alpine UPZ 160 Pharma used system by Alpine Originals. The Hosokawa Alpine Ultraplex UPZ is a universal fine impact mill. It is used to grind soft dry materials. This micronizer is perfect to pulverize different coarse products down to a finer powder and within different industries where micronization might be needed, such as minerals, chemicals, food, pharma, cosmetics, recycling, etc. This grinder can be used for the pre-cut of different materials. It is able to process coarse products up to approx. 3 Mohs´ hardness by reaching medium to fine particles with end-product fineness values between d97 150 to 850 microns (µm) top size (product dependent) at the lowest possible energy consumption. The turbo mill can reach this wide final product range thanks to a variety of easily interchangeable grinding tools such as pin disc, plate beater, beater disc or p ...

Fully refurbished Hosokawa Alpine UPZ 315 used machine by Alpine Originals. The Hosokawa Alpine Ultraplex UPZ is a universal fine impact mill. It is used to grind soft dry materials. This micronizer is perfect to pulverize different coarse products down to a finer powder and within different industries where micronization might be needed, such as minerals, chemicals, food, pharma, cosmetics, recycling, etc. This grinder can be used for the pre-cut of different materials. It is able to process coarse products up to approx. 3 Mohs´ hardness by reaching medium to fine particles with end-product fineness values between d97 150 to 850 microns (µm) top size (product dependent) at the lowest possible energy consumption. The turbo mill can reach this wide final product range thanks to a variety of easily interchangeable grinding tools such as pin disc, plate beater, beater disc or pendulu ...

Combi steamer Manufacturer: UNOX / Type: BAKERTOP Specifications: Model oven: XEBC-06EU-E1R Including base frame & extractor hood 400V / 50/60Hz / 9.9 kW / 16 A CEE plug 230V Schuko plug for the extractor hood Year of construction: 2019 RRP with base: approx. EUR 10,000 General: BAKERTOP MIND. Maps Bakery Oven / Combi Steamer by Unox Body made of stainless steel Low energy consumption due to high-quality insulation Door with double security pane Air gap prevents strong heating of the outer pane inner glass pane can be opened for cleaning Door with carbon fiber door lock and long-bend door hinges Door hinge left / door handle right (door hinge can be changed to the right – see accessories) with condensate tray under the door (direct drain connection) Safety thermostat height-adjustable screw feet Baking chamber: completel ...

Operating voltage: 10 ... 35 V DC (Supply Class 2); Open circuit current (max.): 20 mA; Insulation dielectric strength: 1000 V; Inner diameter: 6.1 mm; Mounting distance to metal (min.): 2 mm; Switching output: pnp, 200 mA, NO/NC, switchable; Pulse extension: 0.1 ... 150 ms adjustable; Part speed (max.): 35 m/s; Response time: 0.20 ms; Waste time: 0.20 ms; Connection: Plug, M12, 4-pin, A-coded

Operating voltage: 10 ... 35 V DC (Supply Class 2); Open circuit current (max.): 11 mA; Insulation dielectric strength: 1000 V; Inner diameter: 35.2 mm; Mounting distance to metal (min.): 30 mm; Switching output: pnp, 200 mA, NO/NC, switchable; Pulse extension: 10 ... 150 ms adjustable; Part speed (max.): 35 m/s; Response time: 0.50 ms; Waste time: 10 ms; Connection: Plug, M12, 4-pin, A-coded

Operating voltage: 10 ... 35 V DC (Supply Class 2); Open circuit current (max.): 11 mA; Insulation dielectric strength: 1000 V; Inner diameter: 15.1 mm; Mounting distance to metal (min.): 5 mm; Switching output: pnp, 200 mA, NO/NC, switchable; Pulse extension: 0.1 ... 150 ms adjustable; Part speed (max.): 35 m/s; Response time: 0.20 ms; Waste time: 0.20 ms; Connection: Plug, M12, 4-pin, A-coded

Operating voltage: 10 ... 35 V DC (Supply Class 2); Open circuit current (max.): 20 mA; Insulation dielectric strength: 1000 V; Inner diameter: 51 mm; Mounting distance to metal (min.): 10 mm; Switching output: pnp, 200 mA, NO/NC, switchable; Part speed (max.): 25 m/s; Connection: Plug, M12, 4-pin, A-coded

Betriebsspannung: 10 ... 35 V DC (Supply Class 2); Leerlaufstrom (max.): 11 mA; Isolationsspannungsfestigkeit: 1000 V; Innendurchmesser: 15.1 mm; Mounting abstand zu Metall (min.): 5 mm; Schaltausgang: pnp, 200 mA, NO/NC, umschaltbar; Impulsverlängerung: 0.1 ... 150 ms einstellbar; Teilegeschwindigkeit (max.): 35 m/s; Ansprechzeit: 0.20 ms; Abfallzeit: 0.20 ms; Anschluss: Stecker, M12, 4-pin, A-kodiert

Number of tool slots: 25, max. rotational speed: 6300/min, tool cone: SK40 with DIN 7388 tightening pin, connected load: 35kVA, controls: Deckel Maho MillPlus, operational/ spindle hours: 56,344/ 14,965h, with chip conveyor and 600l coolant tank, without tools and clamping devices.

Travel X/Y/Z: 500mm/400mm/350mm, distance table-pin nose: min. 250mm/max. 600mm. Work table clamping surface X/Y: 650mm/450mm, max. table load: 500kg, erosion limit load: approx. 300N. Internal dimensions of work bowl X/Y/Z: 845mm/635mm/340mm, max. filling height:: 300mm, max. workpiece height: 260mm. Documentation available. On-site inspection is possible.

Fork length: 1150mm, load capacity: 1.4 kg with a load center of 600mm, weight without battery: 278kg, battery weight: 45-55kg, lithium-ion battery and activation by PIN code, only 17 operating hours, can be inspected on site.

: neu : ca. 12 - 14 Wochen ab Auf : Deutschland : 25230 € : 1250x2500 mm : HYPERTHERM Powermax 45 XP : 6 mm : 12 mm : 25 mm : 4 mm : 45 A : 45 A 50 % ED, 32 A 100 % A : 24 m/min : 1/10 mm : 470 l : 500 kg/m² : 3060 mm : 1760 mm : 1500 mm : 500 kg compressed air powered plasma sourceHYPERTHERM Powermax 45 XP CNC-workbench software (external PC not included) adjustable rollers precision profile rail guide(HiWin) zero backlash HTD drive belt driven by step motors solid frame construction seperate renewable support grate water trough to catch flying sparks swimming burner bearing in combination with exchangeable slide screws, enables constant cutting height hand operation unit for comfortable processing and set up on the workpiece users manual in GERMAN according to CE rules ALTERNATIVE PLASMA SOURCES: HYPERTHERM PMX 65 Sync PMX 85 Sync PMX 105 Sync PMX 125 Sync plasma type comp. air co ...

: neu : ca. 12 - 14 Wochen ab Auf : Deutschland : 22750 € : 1000x2000 mm : HYPERTHERM Powermax 45 XP : 6 mm : 12 mm : 25 mm : 4 mm : 45 A : 45 A 50 % ED, 32 A 100 % A : 24 m/min : unter 1/10 mm : 300 l : 400 kg/m² : 2560 mm : 1460 mm : 1500 mm : 400 kg compressed air powered plasma sourceHYPERTHERM Powermax 45 XP CNC-workbench software (external PC not included) adjustable rollers precision profile rail guide(HiWin) zero backlash HTD drive belt driven by step motors solid frame construction seperate renewable support grate water trough to catch flying sparks swimming burner bearing in combination with exchangeable slide screws, enables constant cutting height hand operation unit for comfortable processing and set up on the workpiece users manual in GERMAN according to CE rules alternative plasma sources: HYPERTHERM PMX 65 Sync PMX 85 Sync PMX 105 Sync PMX 125 plasma type comp. air c ...

MAK 32/ INJ. VALVE SLEEVE / 7 PCS MAK 32/ CYLINDER HEAD STUD /6 PCS MAK 32/ ROCKERARM / 1PC MAK 32/ PISTON COMPLETE / 3 PCS MAK 32/ PISTON SHANK / 3 PCS MAK 32/ GUDGEON PIN / 3 PCS

SPECIFICATIONS: Installed power: 6 kW Workpiece length: 1200 mm Pin width: max 100 mm Accessories: 1 soundproofing room 1 loader

SPECIFICATIONS: Installed power: 6 kW Workpiece length: 1200 mm Pin width: max 100 mm Accessories: 1 soundproofing room 1 loader

Pin-Convert-Extruder, GE 120 SC, make Berstorff, cold lined

thickness of jaw: 150 / 160 / 200 mm max. clamping width: 105 / 138 / 275 mm ca. high of jaw: 46 / 63 mm New machine vices on rotating plate 360 °, provided with 180 ° degree scale from remaining stock at a special price. The body is made of high quality gray cast iron (FC-25), jaws made of rolled steel, hardened, replaceable. Mod.M 150: span: 105 mm, jaw height: 46 mm, dimensions: 600x200x160 mm, Weight: 26 kg, photos 1-3, price 270, - + VAT. Mod. M 160: with covered spindle, three-way adjustable via socket pin, Span: 275 mm, jaw height: 63 mm, dimensions: 800x270x200 mm, weight: 43 kg, photos 4-6, price 780, - + VAT. Mod.M 200: span: 138 mm, jaw height: 63 mm, dimensions: 700x260x200 mm Weight: 54 kg, photos 7-9, price 495, - + VAT. Machine dealer with own stock of 1600 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Gear motor, three-phase motor with gearbox WEG ODG 534 ( ODG534 ) 36 rpm Gearbox: Type GF 13 ( GF13 ) Gear ratio: 38 engine: 0,, 09 kW 1370 rpm 220 / 380 V 3 AC 50 Hz IP44 Shaft diameter: Ø 20 / 34 mm Wavelength: 39 / 55 mm driver pin: : Diameter: Ø 6 mm, length: 35 mm Flange diameter: Ø 80 / 120 mm bolt circle diameter: Ø 100 mm 4x bore: Ø 9 mm used, tested ! Dimensions: 270 x 265 x 150 mm

Inductive length probe, probe, axial TESA SWISS MADE GT61 3230041 pin travel: 10,3 mm diameter: Ø 8 mm total length (without cable): 125 mm approx. 2.0 m connection cable Dimensions plug ( without cable ): 90 x 42 x 17 mm used, tested ! Dimensions ( packaging ): 160 x 150 x 40 mm

Meßtaster FEINMESSZEUGFABRIK SUHL 76 4011:001 Measuring pin travel: 30 mm diameter: Ø 8 mm total length: 198 mm approx. 1.5 m connection cable used, tested ! Dimensions ( without cable ): 198 x 53 x 17 mm

Piston 3 pieces Ø 106.5 mm diesel engine -Piston: Ø 106.5 mm -Piston height: 112 mm -Piston pin: Ø 41,278 mm -Complete price: 3 pieces -Weight: 1.4 kg/piece

Piston 4 pieces Ø 106.5 mm diesel engine -Piston: Ø 106.5 mm -Piston height: 112 mm -Piston pin: Ø 41,278 mm -Complete price: 4 pieces -Weight: 1.4 kg/piece

Piston 2 pieces Ø 106.5 mm diesel engine -Piston: Ø 106.5 mm -Piston height: 112 mm -Piston pin: Ø 41,278 mm -Complete price: 2 pieces -Weight: 1.4 kg/piece

TIG hose package, welding torch, hand welding torch, TIG torch -with torch body -Length: 4 m -Tuchel connector: 3-pin -Water: chilled -Number: 2x hose packages available -Price: per piece -Weight: 2.4 kg

Piston 2 pieces Ø 106.5 mm diesel engine -Piston: Ø 106.5 mm -Piston height: 112 mm -Piston pin: Ø 41.278 mm -Complete price: 2 pieces -Weight: 1.4 kg/piece

Valve islands, multi-pin plug connection, directional control valve, solenoid valve, pneumatic valve, air valve, pressure valve -Type: CPV14-GE-MP-4 -Connection: electrical -Number: 8x valves available -Price: per piece -Weight: 1.5 kg

Pneumatic cylinder BOSCH 7471 324 411 ( 7471324411 ) stroke: 850 mm piston diameter: Ø 63 mm rod diameter: Ø 22 mm Rod thread: M20 x 1,01 5, Length: 48 mm Nominal pressure: 10 bar Connection thread ( inside ): 3/8 ( inch ) 2x Swivel pin: Ø 20 mm, length: 20 mm Position: 600 / 400 mm New ! Dimensions: 1060 x 130 x 75 mm