pet injection used for sale

Two injection moulding machines are available. 1) Ferromatik K 110 1100-493, year of manufacture: 2000, clamping force: 1100kN, min. mould installation height: 300mm, max. opening stroke: 550mm, screw diameter: 40mm, injection volume: 201cm³. The control no longer starts up properly, probably due to the circuit board. Includes a 3-axis handling robot Remak. Without conveyor belt. 2) Arburg 270 M 500-90, year of manufacture: 1995, clamping force: 500kN, min. mould installation height: 225mm, max. opening stroke: 325mm, screw diameter: 30mm, injection volume: 70cm³. The cylinder is slightly leaking. Documentation available. An on-site inspection is possible.

Engel Injection Machine Type ES 1500T/160 V – ELAST Stroke slide plate 300mm Stroke central ejector for slide plate 100mm Force central ejector for slide plate 30kN Stroke lateral mechanical ejector 250mm Stroke lateral hydraulic ejector 250mm Force lateral hydraulic ejector 80kN Stroke central ejector 120mm Force central ejector 20kN Pump drive power 15kW Oil filling 1 225 Operating pressure of hydraulic system 250bar Capacity temperature control unit 2x3 kW Total connected load 48kW Dims: 2675mm long x 1350mm wide x 3310mm high Weight: 6900 With instruction manual

Key data: 850 kN, 40 mm

R1295Injection moulding machine ARBURG 320-850-210 Multronica Screw D=40mm Locking force 85 t.Converted from floppy disk drive to CL drive Viewing by e-mail appointment is desirable Sale only to traders and under the following conditions The machine is considered to have been taken over when it leaves the company, subsequent complaints cannot be taken into account So no guarantee and return.We do not assume any liability for compliance with all requirements mentioned in the UVV (accident prevention regulations)

An almost like-new injection moulding machine Arburg is available. Clamping force: 1600kN, tie bar distance: 520mm, clamping stroke: 364mm, ejector stroke: 150mm, ejector force: 40kN, injection unit: 400, injection pressure: 2500bar. Machine dimensions X/Y/Z: approx. 6000mm/1800mm/2200mm, weight: approx. 6000kg, control: Selogica, operating hours: approx. 67h. Includes enclosure with clean air supply FilterFanUnit and removal robot. Documentation available. An on-site inspection is possible.

CLAMPING FORCE: 150TON PLATEN SIZES: 1295 X 990 DBTB: ROTARY TABLE 1520 MIN MOULD HEIGHT: 300 MOULD OPENING STROKE: 400MM MAX DAYLIGHT: 700MM SCREW DIAMETER: 40MM INJECTION PRESSURE: 2678BAR STROKE VOLUME: 283CM3 SHOT WEIGHT (P/S): 257GR CONTROLS: UNILOG B6 MOTOR: 22KW HEATING CAPACITY: 12.1KW SCREW DRIVE: HYDRAULIC CORE PULLING: 4 AIR VALVES: 1 HOT RUNNER: 8 ZONE INTERGRATED ADDITIONAL: HORIZONAL INJECTION VERTICAL CLAMP

Clamping force: 220kN, min. mould height: 200mm, max. opening stroke: 200mm, max. platen distance: 400mm, ejector stroke: 80mm, machine dimensions X/Y/Z: approx. 2600mm/800mm/1600mm, weight: approx. 760kg. An on-site inspection is possible.

ENGEL ES 1350/350 HL injection moulding machine was built in 1995 in Austria by ENGEL AUSTRIA GmbH. The machine, which is designed for the economical production of plastic parts, is distinguished by the use of many components with excellent technical parameters. These parts are produced using the reliable injection moulding method, which involves feeding plasticised plastic into a mould and then clamping it with high press force. A precision mould clamping system, operating at a maximum force of 350 tonnes, guarantees high repeatability and quality of the manufactured parts. Once the production process is complete, the robot automatically transfers the finished products from the workspace to a conveyor belt. The ES 1350/350 HL injection moulding machine weighs 5000 kg. Technical specifications of the ENGEL ES 1350/350 HL injection moulding machine - CNC controller: ENGEL - maximum m ...

Key data: 600 kN, 132 g/PS, 35 mm

Arburg 320C-600-250 Injection Moulding Machine (241) Ability to work vertically Number: 241 Availability: in stock Year of production: 2008 Producer: Arburg Condition of Injection Molding Machine: Used Screw diameter [mm]: 35 Injection weight [g]: 132 Injection pressure [bar]: 1820 Clamping force [kN]: 600 Gap spacing [mm]: 320×320 Panel size [mm]: 446 x 446 Min. mould height [mm]: 200 Control Type: Selogica Tongue: German Installed power [kW]: 23.9 Working hours [h]: 74753 Weight [kg]: 2330 Dimensions [mm]: 3500×1500 Feed hopper: NO Robot Socket: Yes Core String: 1x

2012 KRAUSS MAFFEI 850-1400-1000 MX Z Injection moldin machine missing electrical and mechanical parts Find more here - / Contact us at -

2008 SAR/KUKA R/SCHS/GR/ETI/UST/MED/FB/HBG/BAS Injection robot Machine was functional before conservation, obsolete robot version, retrofit could not be done. Find more here - / Contact us at -

Key data: 220 kN

Awaiting refurbishment at our headquarters in Northamptonshire is this BOY 22M injection moulding machine. Any machines awaiting refurbishment (or undergoing refurbishment) with us can be reserved with a 10% deposit and we then prioritise the refurbishment and aim to have the machine available for inspection within 8 weeks from order. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Prices shown are ex-works, but we can quickly provide DAP (Delivered at Place) Incoterm pricing on request. We can take out the hassle and addi ...

Awaiting refurbishment at our headquarters in Northamptonshire is this BOY 55A injection moulding machine, fitted with the Procan CT Controller. Any machines awaiting refurbishment (or undergoing refurbishment) with us can be reserved with a 10% deposit and we then prioritise the refurbishment and aim to have the machine available for inspection within 8 weeks from order. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Prices shown are ex-works, but we can quickly provide DAP (Delivered at Place) Incoterm pricing on reques ...

4 x Demag injection moulding machines Demag 80 to BJ 2005 Demag 420 to BJ 2003 Demag 420 to BJ 2005 Demag 420 to BJ 2008

Key data: 800 kN, 239 g/PS, 45 mm

The machine is in good condition and has been maintained during operation at short maintenance intervals. The machine is connected and fully functional. A visit with a test is possible. All documents for the machine are available. The screw, heating cylinder tube and RSP were renewed in 2022 by Plasma Kunststofftechnik. Baseline: - No: 21953 - Year of construction: 1991 - Weight: 4000kg. - Clamping force: 800kn - Dimensions: 3910mm x 1380mm x 2050mm (LxWxH) - Control:CC100 Technical details: - Operating voltage: 400V 3~50Hz - Worm: 45mm - Screw geometry: 3-zones - Dosing distance max.: 160mm - Nozzle thread: M28x1.5 - Max. spray pressure: 1300 bar - Injection weight PS: 239g - Horizontal spar spacing: 405mm - Vertical spar spacing: 345mm - Opening travel max.: 430mm - Installation height min: 150mm - Installation height max.: 430mm - Centering: 125mm - Cooling  ...

Injection moulding machine Engel e-motion 2440/380 T BJ 2008

2 x Husky HL500RS80 2016 injection moulding machines

Injection moulding machine Krauss Maffei KM 50/90 C2 BJ 2001

Manufacturer: Krauss Maffei Model: 800-5700 MC Year of Manufacture: 1999 Technical Data - Clamping Force: 8000 kN - Platen Size: 1600 × 1510 mm - Tie Bar Distance: 1120 × 1000 mm - Mold Height: 600 – 1100 mm - Daylight (Platen Opening): 2000 mm - Total operating hours (machine switched on) : currently 02,193.40 - Operating hours in production : currently 82,849.13 - Heating Capacity: 59 kW - Control: MC4 Injection Unit - Screw Diameter: 105 mm - Shot Volume: 3611 cm³ - Injection Pressure: 1580 bar - Dimensions (L×W×H): 10.15 × 2.86 × 2.40 m - Pump Drive Power: 110 kW - Oil Tank Capacity: 2000 L - Machine Weight: approx. 45 tons Features / Extras - 8 temperature control zones + 2 additional zones for plasticizing heating - 4 core pulls with movable platen - Hydraulic rotary bolt shut-off nozzle (HSVS) - Air valve (1x on movable platen, WAP) - T-slots in clamping plates ac ...

Presse à injecter ENGEL VC 200/80 Année : 2005 Nombre d’heures : 79 000 h Force de fermeture : 80 T Course d'ouverture : 450 mm Epaisseur moule min : 250 mm Dimensions des plateaux : 670 x 600 mm Diamètre bagues de centrage : 125 mm diamètre de la vis : 35 mm Volume injectable : 154 cm3 COMMANDE : CC200 1 noyau hydraulique interface robot : Euromap 67 DONNÉES GÉNÉRALES : Puissance de chauffage installée : 6,8 kW Puissance d'entraînement de la pompe : 15 kW Puissance totale connectée : moteur + chauffage Poids total : 5.200 kg Dimensions totales L x l x H : 4,0 x 1,4 x 2,0 m

2 x Injection Molding Machines Manufacturer. Arburg Type : 270S-250-60 BJ 1996

Netstal Elion 800 injection moulding machine with Wittmann Handling Primus The machine is fully functional and has only 6500 operating hours

Injection moulding machine Arburg 470C 2000-675 BJ 2007

Injection moulding machine Krauss Maffei KM 300-1900 C2 BJ 2000

Injection moulding machine Arburg 420S 1300-350 BJ 2000 without handling

Key data: 5500 , 80

Presse à injecter ENGEL 550 T Type ES1800 Année : 1998 E parfait état de fonctionnement

Key data: 3000 , 702 , 60

Presse à injecter ENGEL 300 T Type : VICTORY 1800 / 300 POWER Année de fabrication : 2008 En bon état de fonctionnement Force de fermeture : 3000 KN / 300 T Diamètre vis : 60 mm Volume injectable : 763 cm3 Poids de l’injection en PS : 702 gr Pression d’injection : 1960 bars Vitesse d’injection : 284 cm3/s Course ouverture moule max : 900 mm Epaisseur min moule : 400 mm Dimensions des plateaux : 1100 x 1100 mm Nombre de litres d’huile : 870 L Dimensions : 7,2 x 2,0 x 2,50 m Poids machine : 20 000 kg

Presse à injecter ENGEL 180 T Type : VICTORY 500/180 POWER Force de fermeture : 1800 KN - 180 T Année : 2008 Diamètre de la vis : 45 mm Volume d'injection : 318 cm³ Pression d’injection : 2040 bars Épaisseur min/max moule : 300 750 mm Distance entre colonnes : 860 x 830 mm

Key data: 1500 , 220 , 40

Presse à injecter ENGEL 150 T type ES 500/150HL Année de fabrication : 2001 En bon état de fonctionnement Force de fermeture : 1500 KN / 150 T Diamètre vis : 40 mm Volume injectable : 251 cm3 Pression d’injection : 1300 bars Rapport L/D. : 20 Nombre de zones de chauffe : 4 Ouverture max des plateaux : 950 mm Course d’ouverture : 700 mm Course de l’ejection. : 150 mm Epaisseur min moule : 250 mm Dimensions des plateaux : 820 x 750 mm Dimensions : 5,45 x 1,60 x 2,40 m Poids : 13 000 kg

Injection moulding machine Demag erg. 250/560 840 BJ 2001

Injection Molding Nose Demag ergotech 50/370-200 BJ 2000

Injection moulding machine Engel victory 200H/200V790 comb BJ 2018

Key data: 16000 , 10131 , 150

Presse à injecter HAITIAN 1600 T Type : MARS MA 16000/15800 Force de fermeture : 16 000 KN Année : 2011 Course d’ouverture moule : 1600 mm Epaisseur moule min / max : 700 / 1500 mm Course d’ouverture max des plateaux. : 3100 mm Distance entre colonnes : 1550 x 1430 mm Dimensions des plateaux : 2230 x 2120 mm Course d’éjection : 400 mm Force d’éjection : 318 KN Diamètre vis : 150 mm Volume théorique d'injection: 11 133 cm3 Poids de l’injection en PS : 10 131 gr Rapport L/D : 20,8 Pression d’injection max. : 149 MPA Capacité de plastification : 220 gr/sec Vitesse d’injection : 1527 gr/sec Vitesse rotation vis : 102 tour/min Puissance chauffe. : 122 KW Puissance moteur électrique: 65 + 65 + 45 Quantité d’huile dans réservoir : 1610 litres Dimensions : 15,2 x 4,5 x 4,5 m Poids total : 107 T

Key data: 900 , 183 , 40

Presse à injecter ENGEL 90T type ES 330/90 HL Année de fabrication : 1995 En bon état de fonctionnement Force de fermeture : 900 KN / 90 T Diamètre vis : 40 mm Volume injectable : 201 cm3 Poids de l'injection en PS : 183 gr Pression d’injection : 1300 bars Nombre de zones de chauffe : 4 Ouverture max des plateaux : 950 mm Course d’ouverture : 500 mm Epaisseur min moule : 250 mm Dimensions des plateaux : 710 x 420 mm Dimensions : 4,22 x 1,42 x 2,00 m Poids : 5 900 kg

injection molding machine Angel Type: Victory 330/80 Tech Machine No: 155871 Age : 2005

Injection moulding machine Stork N-2500-1400 Injection unit: Spray pressure (max.) 2100 bar Spray volume (max.) 595 cc Injection weight hp (max.) 565 g Spraying speed (max) 299 cc/s Nozzle (immersion depth) Clamping unit: Clamping force 250 tons Locking force 275 tons Size of the clamping plate (hor. + vert.) 920 X 920 Opening stroke (max.) 575 mm Max. tool weight Tool height (min./max.) 200-685 Clear width between the bars 585-585 mm Discharge stroke (max.) 175 mm Ejector diameter max.80 mm Centering ring (DS-AWS) 160 mm Max. clear width between clamping p. Options: Core pull (time limit switch) Freely programmable Ejector plate (end position control)  ...

Ideal for operating a business where power outages are not desired, for example injection molding R1334 Power Generator Emergency Power Generator POLYMA/DEUTZ 80 KVA installed in a truck trailer single-axle, was used on construction sites. Dirty outside by leaves and dirt Polyma Kassel 80KVA = 16A = 64 KW,Diesel engine Deutz type F6L912 7ßKW 95hp 2000 rpm., With diesel hand pump hose in canister and pump,With cable/plug 63 A, The trailer is not soundproofed, stood outdoors for years under canopy and is accordingly polluted More detailed pictures on request

Key data: 1600 kN, 184 g/PS, 40 mm

Arburg 520A-1600-400 (228) Hybrid Injection Moulding Machine Number: 228 Availability: in stock Year of production: 2007 Producer: Arburg Condition of Injection Molding Machine: Used Screw diameter [mm]: 40 Spray weight [g]: 184 Injection pressure [bar]: 2000 Clamping force [kN]: 1600 Gap spacing [mm]: 520 x 520 Panel size [mm]: 795 x 795 Control Type: Selogica Tongue: English, German Installed power [kW]: 21.2 Working hours [h]: 83564 Weight [kg]: 9000 Dimensions [mm]: 5500 x 2000 Feed hopper: NO Robot Socket: Yes Air valve: 3x

Presse à injecter ARBURG 100 T type 420C 1000-250 Année de fabrication : 1999 En bon état de fonctionnement Pompe neuve Force de fermeture : 1000 KN / 100 T Diamètre vis : 40 mm Volume injectable : 188 cm3 Pression d’injection : 1530 bars Rapport L/D : 18 Ouverture max des plateaux : 750 mm Epaisseur min moule : 250 mm Dimensions des plateaux : 570 x 570 mm Entre colonnes : 420 x 420 mm Dimensions : 4,15 x 1,60 x 2,02 m

Key data: 1600 kN, 359 g/PS, 50 mm

Machine in good condition, dry, clean, ready for production. The pump is quiet and the injection molding is precise. Everything works perfectly. With 2 core pulls and robot connection, with quality control program. - Immediately available in our warehouse in Budapest, loaded onto the customer's truck free of charge or delivered to the customer's home for a refund of freight costs. - Function-tested (functional guarantee) - The machine can also be checked when it is switched on Information about the machines we offer and our company: - We only sell machines that we own and can be purchased from our warehouse in Budapest. - We inspect and test each offered machine before delivery - we do NOT sell non-functional goods - we are NOT a third-party intermediary. - All machines offered come from successful companies for which maintenance and care are a matter of course - all offered mac ...

Key data: 1000 kN, 127 g/PS, 35 mm

Regularly serviced machine that is always kept in top shape. The screw rotation is carried out with an electric servo motor, which is an energy-efficient solution. The rest of the machine is identical to the standard version of the 420 S. The presence of the core puller in this type is extra. Another special feature is that the injection molding unit can be moved from the center. Software and technologies can be read from a CF disk. The notification can be made in both Hungarian and German. Manuals can also be in German or Hungarian. Currently, the machine has a 35 mm auger for technical materials in good condition. A video of the operation of the machine was also created, which can also be tried out in person at our site. Please see our other ads. Information about the machines we offer and our company: - We only sell machines that are owned by us and can be purchased in our warehouse ...

Key data: 1100 kN, 201 g/PS, 40 mm

Machine in good condition, dry, clean, ready for production. The pump is quiet and the injection molding is precise. Everything works perfectly. With 2 core pulls and robot connection, with quality control program. - Immediately available in our warehouse in Budapest, loaded onto the customer's truck free of charge or delivered to the customer's home for a refund of freight costs. - Function-tested (functional guarantee) - The machine can also be checked when it is switched on Information about the machines we offer and our company: - We only sell machines that we own and can be purchased from our warehouse in Budapest. - We inspect and test each offered machine before delivery - we do NOT sell non-functional goods - we are NOT a third-party intermediary. - All machines offered come from successful companies for which maintenance and care are a matter of course - all offered mac ...

Key data: 3200 kN, 703 g/PS, 55 mm

Machine in good condition, dry, clean, ready for production. The pump is quiet and the injection molding is precise. Everything works perfectly. With 2 core pulls and robot connection, with quality control program. - Immediately available in our warehouse in Budapest, loaded onto the customer's truck free of charge or delivered to the customer's home for a refund of freight costs. - Function-tested (functional guarantee) - The machine can also be checked when it is switched on Information about the machines we offer and our company: - We only sell machines that we own and can be purchased from our warehouse in Budapest. - We inspect and test each offered machine before delivery - we do NOT sell non-functional goods - we are NOT a third-party intermediary. - All machines offered come from successful companies for which maintenance and care are a matter of course - all offered mac ...

Key data: 4000 , 1464 , 80

Screw diameter: 80 mm Injectable volume: 1678 cm3 Injectable weight: 1464 g Injection pressure: 1856 bar Column passage: 800 x 800 mm Opening stroke: 1020 mm

Injection moulding machine Krauss Maffei KM 200-1400 C2 BJ 2000

Rep M46 Injection Moulding Machine Size of platens 430x430mm Injection unit short volume 670cm3 Injection pressure 1690 bar Injection force 331kN

Screw diameter: 70 mm Injectable volume: 1078 cm3 Injectable weight: 981 g Injection pressure: 1877 bar Column passage: 630 x 630 mm Opening stroke: 820 mm 8 Zone Heater 3 Hydraulic Cores Robot interface

Key data: 20000 kN

Angebot/Offer: Engel Duo 17060/2000 Viper Robot 60 approx. 4900h YOC 2021

Presse à injecter BILLION 200T Bi-matière HERCULE H260-470/200 Commande Dixit 500 Année : 1998 Nombre d’heures: 23 000 heures Caractéristiques des 2 groupes d’injection : Groupe H260 : diamètre 32 mm - volume injectable de 116 cm3 Pression d’injection : 2205 bars Groupe H470 : diamètre 38 mm - volume injectable de 198 cm3 Pressions d’injection : 2327 bars Diamètre bague du plateau : 100 mm Distance entre colonnes : 610 x 610 mm Dimensions des plateau : 870 x 870 mm Course d'ouverture : 560 mm Epaisseur du moule min/max : 280-580mm Capacité du réservoir d’huile : 500 litres Interface robot Robot STAR 1000EMIII 3 Course en X : 2100 mm / Course en Y : 750 mm / Course en Z : 1000 mm

An Arburg injection molding machine with integrated rotary table is available. Connected load: 61kW, clamping force: 500kN, opening force: 40kN, opening stroke: 250mm, max. mold installation height: 270mm, platen distance: 520mm, rotary table diameter: 900mm, rotation angle: 180°, max. table load: 240kg, max. injection pressure: 2500bar. Machine dimensions X/Y/Z: approx. 3250mm/2000mm/2600mm, weight: approx. 3200kg, operating hours: 6244h. Documentation available. An on-site inspection is possible.

Eight Arburg injection molding machines, one Engel injection molding machine, and one Demag injection molding machine are available. 1) Arburg 270M 350-90, year of manufacture: 1996, operating hours: approx. 110000h. 2) Arburg 270M 350-90 U, year of manufacture: 1998, operating hours: approx. 108000h. 3) Arburg 270M 350-90, year of manufacture: 1992, operating hours: approx. 178000h. 4) Arburg 420C 1000-250, year of manufacture: 1995, operating hours: approx. 96000h. 5) Arburg 370C 800-225, year of manufacture: 1992, operating hours: approx. 156000h. 6) Arburg 320M 500-90, year of manufacture: 1991, operating hours: approx. 94000h. 7) Arburg 270M 350-90 U, year of manufacture: 1998, operating hours: approx. 83000h. 8) Arburg 630S 2500-675, year of manufacture: 2003, operating hours: approx. 93000h. 9) Demag Viva 100-400, year of manufacture: 1999, operating hours: approx. 116000h. 10) En ...