maximum number of results exceeded > 1000
please refine your search
Belt width: 75 mm Belt length: 2000 mm Sanding belt dimensions: 75 x 2000 mm Snatch: 200 x 75 mm Plan grinding area: 590 x 75 mm Belt speed: 15 / 30 mtr. / sec. Working height: 600-1200 mm Total power consumption: 2.4 / 3.0 KW / 400 V Machine weight: 130 kg Machine dimensions: 1150 x 650 x 670 mm Facilities / features vibration-free running Quick adjustment for horizontal + vertical position continuous plan grinding surface by simply opening of the cover Quick-clamping belt passing pole-reversible motor Quick belt change incl. factory warranty All technical data are created according to our best knowledge and existing documents; Expressly reserved by mistake. Each pa ...
State: Machine will be refurbished IX-Axis Travel (mm): X-Axis Travel (mm): X-Axis Travel (mm): Worktank length: Worktank width: Worktank height: Max. workpiece length: Max. workpiece width: Max. workpiece height: Max. workpiece weight: Taper angle/height: Automatic Wire Feeding: Length x width x height: Weight (kg): Worked power hours: The technical data and illustrations are not binding. They are not warranted characteristics and are subject to change.
stationary desilting plant of solids top hanging BigBag 1 600 mm long 1 370 mm width Height. 2 800 mm Operating voltage 230V / 50 Hz Power voltage. 24V AC El.Verbrauch asi 3 kW / h El. Protection. IP 65 Operating temperature + 5 C 20A + 40 C. Operating pressure 0,4-0,5 MPa Compressed air consumption 8-45 m Weight approx. 600 kg Stock removal. Max 350 kg Information on the system The basic part of the Abrasiventfernungssystems consists of a welded steel construction, on which all the necessary parts are arranged: a pneumatic pump, a slurry pump, an electronic control device for the operation, a mechanical Hydro cyclone. Stainless steel suction heads, through the water insid ...
The machine worked from the news for about a year, it was later dismantled. Since then stored in a heated hall, protected from dust. Inability to install and test the machines in action. Based on visual inspection found the completeness of the device.
Water jet cutting system, as 3-axis version with ballscrew. Suitable for pressure up to 4,136 bar. The cutting system is manufactured in Europe and components of from well-known manufacturers are installed. The CNC control is an easy to use P 886 Dimensions of the working surface of the machine: -X-axis (Portal). .2000 mm -Y-axis (legs). 1000 mm Z axis. 200 mm -Z axis movement by brushless motor Overall dimensions of the machine: -X axis. . 3 420 mm -Y... 4,480 mm -Z axis... 1800 mm Working speeds of the X - and Y-axis: -Max.. . 12.000 mm / min Travel speed of the X - and Y-axis -Max.. 30, 000 mm / min Working speeds of the Z-axis: -manual supply. 5000 mm / min -Ma ...
Machine designed for vertical wells. It is used in construction works. During the inspection no malfunctions or shortages were found in the equipment or equipment (except batteries).
3-axis abrasive water jet cutting machine up to 4,100 bar pressure. Modern user-friendly control, version 3 axes New machine Table size 2,000 x 3,000 mm Z axis 200 mm Table load default 800 kg / sqm Positioning accuracy +/-0,04 mm / 300 mm Repeatability +/-0.03 mm Maximum speed 16 000 mm / min Maximum lateral speed 20 000 mm / min Facilities: â?¢ Basic steel bearing structure with steel Portal â?¢ CNC-control P 886 â?¢ Precision linear guides â?¢ hardened and cut racks and stainless steel pinion â?¢ precision planetary gearboxes with servo motors â?¢ Stainless steel cover â?¢ Cutting head for 3 ...
Continuous reactor In-line dispersing machine (1x), Make Kotthoff, Type MS-3D, No 31859, New 1977, Reconditioned in 2004 by Fluko, Material stainless steel, Rotor sizes dia. 280x300mm, With jacket, With mechanical seal, Motor 24,0 KW, 500 Volt (Ex), Extra Specifications - Has not been used after reconditioning (new mechanical seal and bearings) in 2004CONTINUOUS REACTORSMIXERS > CONTINUOUS REACTORS
Edgebander euro AKV2001DK by lifting skirt, only 4 m long, but fully equipped! Heating rail 8 mm equipment, four milling units, RADIUS scraping and buffing wheel Edge thickness up to 8 mm Workpiece thickness up to 45 mm Feed approx. 11m / min Extraction adapter 140 mm Aggregates: Top pressure manually adjustable with Handwheel and display Heating rail to preheat the plate, ideally in unheated garages Gluing unit with quick heating pool Pressure zone Compound miter saw Flush trimming unit, swiveling 15deg before milling RADIUS milling unit, equipped with R2 RADIUS scraper R2, front einrueckbar Buffing unit pull-out workpiece support Plate infeed and outlet type Hood la ...
Grinder, Pin disc mill, Make Alpine Augsburg, Type A-400 CW Contraplex Weitkammer, No 128316, New 1963, Material mild steel, 2 Driven rotors, Rotor size dia. 400mm, Number of pins on door side: 134 stk, House size +/- 1100x1350mm, Motor 11,0 kW (housing) + 30 kW (door), 380/660 Volt, With switchgear, Floorspace 1,9x1,0m, Total height 1,3m, Weight 1500kg, Extra Specifications + REVISED +SIZE REDUCTION MILLSGRINDERS > SIZE REDUCTION MILLS
KMT mobile desludging The CLEANLINE mobile desludging system I removed sand deposits in the cutting basin during cutting operation. Technical data Filling volume without cutting basin 1 m3 Sampling volume 3-4 m3/h Compressed air supply 4-6 bar, 1 m3/min Standard tube length 5 m Net weight 200 kg Length 1100 mm Width: 1000 mm Height 1750 mm The CLEANLINE comes with CE mark and Declaration of conformity according to machinery directive 2006/42/EC.
; Gross weight [kg]: 16000; Engine: Mercedes OM442A; Accessories: 15 meter 250mm pipes
flat grinding machine, almost unused, condition almost like new Manufacturer Bernardo Type BSG 4080 AHD Year 2014 almost unused, absolutely mint condition, estimated about 50 operating hours Electric magnetic clamping plate 800 x 400 mm Table size approx. 910 x 405 mm Travel in x 900 mm Travel in Y 450 mm Holder diameter 400 mm maximum workpiece height 370 mm maximum work-piece weight 500 kg with micrometer-carbide pulley puller hydraulic feed in X (longitudinal) 7 up to 23 meters per minute Feed in Y 0.1 to 8 mm per stroke Automatic vertical (Z) - delivery: 0.005 / 0.01 / 0.02 / 0.03 / 0.04 and 0.05 mm Accessories: Flow filter grinding oil ...
; Gross weight [kg]: 2300; Registration Number: UJ1DL22NX4DK12449; Rear tyres remaining: 50; Front tyres remaining: 50; Maximum lift capacity [kg]: 200
Perkins diesel power generator used see pictures.
; Gross weight [kg]: 3030; Rear tyres remaining: 50; Front tyres remaining: 50; Maximum lift capacity [kg]: 200
Currently 2 x in stock Krahnhubwerk BJ 1980 Mannesmann Demag P625 H8 2 line Weight 5000 kg Lifting height 8 m Lifting speed 8/0, 8 m / min used
; Gross weight [kg]: 3030; Rear tyres remaining: 60; Front tyres remaining: 60; Maximum lift capacity [kg]: 200
Tip height: 300 / 330 mm Top width: 3000 mm Speed range: 12-600 rpm Spindle bore: 83 mm Total power: 7.5 KW / 380 V Machine weight: about 5000 kg Equipment / accessories 4 jaw Chuck 1 festst. Lynette mitlfd. Lathe 4 way Toolpost Chip protection tray Coolant system All technical data are created according to our best knowledge and existing documents; Expressly reserved by mistake. Each party has the opportunity to test the machine before making a purchase in our factory under power.
; Gross weight [kg]: 2300; Registration Number: UJ1DL22NX7DK13277; Rear tyres remaining: 60; Front tyres remaining: 60; Maximum lift capacity [kg]: 200
Control HEIDENHAIN plus iT Circular diameter max. 505 mm swing over plan guide 375 mm travel plan (x) 250 mm Longitudinal travel (z) 635 mm spindle integrated spindle motor, power 40/100%ED 28/21 kW spindle head (flat flange) 5 170 h spindle diameter in front bearing 130 mm torque Max (40 / 100%) 320/240 NM Speed range 25-5,000 rpm Number of tool stations of the tool carrier 12 shank according to DIN 69880 30 mm Tailstock hub automatically movable 580 mm Weight of the machine with chip conveyor 5,600 kg Dimensions L/W/H 4,3 m / 2,022 m / 1.77 m Accessories: feeder Imeca ma ...
; Gross weight [kg]: 2300; Registration Number: UJ1DL22NX3DK12231; Rear tyres remaining: 60; Front tyres remaining: 60; Maximum lift capacity [kg]: 200
Complete KRONES PET Water Filling Line LINE IN PRODUCTION Brand Name : KRONES Year : 2007-2006 , Capacity is 36,000bhp. Krones 2007Key AssetKrones Blowing machine air conditionerHandheld thermal imager Krones Blowing Machine Air CompressorBlowing Machine CoveyerKRONES 550ML Moulding KRONES , 600ml Moulding KRONES Coveyer Krones Filling Machine Krones Labeller film wrapping machineWater Treatment line. Air Compressor Weigh checking Jet Ink Printer CIP System Coveyer Dryer BeltLiquid nitrogen machine KRONES water Level check Packing machine KRONES Filterlable checker Krones control cabinet KRONES Full automatic sprinkling device Laser Marker LED Counterkron ...
Very little used frame and drilling machine series of Gannomat Specifically to the dowel hole drilling at two levels in one clamping Drill level pneumatically adjustable Motor 1,5 kW, 2800 RPM Start the engine with practical handle switch Two-jaw Chuck Röhm 1 to 20 mm maximum height approx. 100 mm Maximum stroke 150 mm Cross adjustment 320 mm continuously variable 2 pneumatic workpiece clamping system Grid rail for quick adjustment side to side, scanning 12 mm Stroke length adjustment with recesses Suction pipe Center stop Double bevel stop adjustable from 0 to 60 degrees Height adjustment for upper and lower level with mechanical digital display and pneumatic switching ...
; Gross weight [kg]: 1860; Rear tyres remaining: 89; Front tyres remaining: 89; Inspection Date: 2018; Amount of previous owners: 1; Lift height[mm]: 1600; Maximum lift capacity [kg]: 200; Full service history: Ja
Model MEX 045 BJ 1988 Version 64/10/ALF Flow rate 6.4 Condensed ultimate pressure 10 bar Engine power 45kW maximum operating speed 2985U/min
; Gross weight [kg]: 2300; Rear tyres remaining: 90; Front tyres remaining: 91; Inspection Date: 2018; Amount of previous owners: 1; Maximum lift capacity [kg]: 200; Full service history: Ja
; Gross weight [kg]: 2330; Rear tyres remaining: 85; Front tyres remaining: 87; Inspection Date: 2018; Amount of previous owners: 1; Lift height[mm]: 1014; Maximum lift capacity [kg]: 450; Full service history: Ja
Glue specification unit for dowel holes and Rueckwandnuten A video of the current machine can be sent on request. With an ergonomic lighter gun to the stating of glue in dowel holes etc. closed glue system, this little cleaning effort Stainless steel tank for 5 L glue Stainless steel tank for 5 L of water (to clean) Rinsing process takes only about 1 minute! Selector water / glue for fast commissioning and cleaning Glue quantity easy selector switch adjustable interval trigger for constant adjustable quantity of glue or permanent operation Ideal complement to an automated drilling and dowel system. Electrical connection 230 Volt 6 bar air connection CE mark Operating instruc ...
; Gross weight [kg]: 3770; Rear tyres remaining: 86; Front tyres remaining: 84; Inspection Date: 2018; Amount of previous owners: 1; Maximum lift capacity [kg]: 215; Full service history: Ja
1 piece CNC band sawing machine Make: Kasto twin AE4 with heavy load conveyor Cutting capacity: 400 x 400 mm smallest cut dimensions: Ã? 10 mm smallest section length: 6 mm cutting speed, continuous: 20-100 m / min Control: Compact control
; Gross weight [kg]: 3800; Rear tyres remaining: 83; Front tyres remaining: 84; Inspection Date: 2018; Amount of previous owners: 1; Maximum lift capacity [kg]: 215; Full service history: Ja
Bystronic Xpert 200x4100 (2012) OVERVIEW Brand: Bystronic Model: Xpert 200x4100 Application Type: Bending Machine Type: Bending machines Availability: Immediately Production Year: 2012 Location: Italy Origin Country: Germany Production Hours: 12567 GENERAL DATA Machine weight: 17600 kg CONTROL UNIT Interface: Microsoft Windows XP MAIN DRIVE Pressing force: 2000 kN Bending length: 4100 mm Main motor power: 18.5 kW Stroke: 415 mm MEDIA Main electronic connection: 400 V Power consumption: 22 kW Air pressure: 8 bar ADDITIONAL EQUIPMENT 1: Tools 2: Fast Bend+
; Gross weight [kg]: 5950; Rear tyres remaining: 85; Front tyres remaining: 87; Inspection Date: 2018; Amount of previous owners: 1; Maximum lift capacity [kg]: 225; Full service history: Ja
BEYELER PR6 (2000) OVERVIEW Brand: BEYELER Model: PR6 Application Type: Bending Machine Type: Bending machines Availability: Immediately Production Year: 2000 Location: Italy Origin Country: Germany GENERAL DATA Machine weight: 23400 kg CONTROL UNIT Brand: CYBELEC Model: DNC 1200 MAIN DRIVE Pressing force: 3200 kN Bending length: 4100 mm Main motor power: 22 kW Stroke: 365 mm MEDIA Main electronic connection: 400 V Air pressure: 8 bar ADDITIONAL EQUIPMENT 1: Tools
; Gross weight [kg]: 5800; Rear tyres remaining: 75; Front tyres remaining: 78; Inspection Date: 2018; Amount of previous owners: 1; Maximum lift capacity [kg]: 230; Full service history: Ja
BJ: 1996 type SV5 690/1/01 capacity at 2800 1/min 690 m³/h at 3300 1/min 900 m³
; Gross weight [kg]: 3000; Rear tyres remaining: 86; Front tyres remaining: 87; Inspection Date: 2018; Amount of previous owners: 1; Maximum lift capacity [kg]: 200; Full service history: Ja
Code: 0475 Brand: STRIEBIG Model: STANDARD TRK 6220 - CE Standard Manual vertical panel saw - CE Standard Integrated vacuum system Large wood supporting surface with n°6 pre-defined cutting points for vertical cut - The horizontal cut is possible in any position. The wood support is movable in vertical and automatically moves depending on the blade position Lenght of cut mm 5300 Height of cut mm 2200 Depth of cut mm 80 Supporting rollers for panels movement Locking device for small parts Blade diameter mm 300 - Hole 30 Speed 4750 rpm Motor power Kw 5,5 - Exhaust outlet diameter mm 160 Overall dimensions mounted machine : mm 6675 x 1600 x 3000 h Weight kg 950
; Gross weight [kg]: 1850; Rear tyres remaining: 85; Front tyres remaining: 85; Inspection Date: 2018; Amount of previous owners: 1; Maximum lift capacity [kg]: 230; Full service history: Ja
In technically and visually good condition. The Primus-series is the smallest conventional precision lathe, builds the hamlet for decades. This machine has decades long proven in the single parts and small series production, in craft & industry, education, training, tool and fixture construction. All feeds, longitudinal & transverse including the Castle nut thread termination function correctly and perfectly, the same applies to HEIDENHAIN position display the entire controls of the machine including the bed plan - and upper carriage, tailstock and the digital. The bed are over the entire working surface in very good condition (see pictures). All spindles of the machine have l ...
; Gross weight [kg]: 5900; Rear tyres remaining: 92; Front tyres remaining: 92; Inspection Date: 2018; Amount of previous owners: 1; Maximum lift capacity [kg]: 200; Full service history: Ja
Force of pressure: 25 t Adjustable stroke: 5-80 mm Slide adjustable: 60 mm Plunger strokes p. min: 120 Adjustable table: 150 mm Table transmission rate: 100 x 150 mm Security clearance: 160 mm Overtravel distance: 36 Weight: 1750 kg Facilities/features: Two-hand operation -Emergency off pushbutton -Adjustable table
; Gross weight [kg]: 6300; Rear tyres remaining: 85; Front tyres remaining: 85; Inspection Date: 2018; Amount of previous owners: 1; Maximum lift capacity [kg]: 200; Full service history: Ja
Machine type CNC lathe - inclined bed machine make SCHAUBLIN type 110 CNC built 1998 control type CNC storage France country of origin Switzerland delivery immediately cargo base stock technical details Turning diameter 420 mm turning length 300 mm control FANUC 18 T c-axis 0.001 degree speed 1750-5000 R/min turret 8 powered tools turning diameter over bed 420 mm additional information Turning diameter over bed 420 mm Spindle bore 32 mm Turning diameter 120 mm Sled: Longitudinal travel (Z axis) 300 mm Plan travel (X-axis) 180 mm C AXIS LIVE TOOLS turret sled: number 1 Number of positions revolver 8 Driven tools revolver 8 Spindle retainer: Camlock Spindle speeds ...
; Power [PS]: 45; Front tyre size: 7.50-16; Rear tyre size: 16.9-28; Rear tyres remaining: 80; Front tyres remaining: 80; Accessories: Verdeckkabine, Diesel; Top speed [km/h]: 38
It is a used Bongard baguette long roller type FAC major for sale. The machine is fully functional and runs quietly. On request, a video can be sent to from the test run.
; Power [PS]: 116; Front tyre size: 275/80-20; Rear tyre size: 275/80-20; Accessories: Forstkabine, Steuergerät - Doppelt wirkend (2x), Druckluftbremse, Diesel, automatische Anhängevorrichtung; Top speed [km/h]: 70