panel used for sale

Pre-milling unit: yes; Pre-milling unit material removal: 0 - 2 mm; Plastic edges: 0.4 - 3 mm; Workpiece thickness: 8 - 50 mm; Workpiece length min.: 130 mm; Workpiece width min.: 80 mm; Glue unit: granules / glue container quick change kit; Chopping knife: yes; Flush cross-cut unit: yes; Corner copying unit: yes; Flush radius milling unit: yes; Radius Scraper Aggregate: yes; Surface scraper unit: yes; Buffing unit: yes; Power consumption: 9 kW; Machine Length: Machine Width: Machine height: Weight: Prima 7.3 r.a. PLUS â€" Partnership Edition Aggregates: Joining milling unit incl. AIGNER Diamant jointing cutter heads, with DIA interchangeable knife system Konstantin and controlled edge blow-out nozzle behind the 2nd joining cutter head. Cross-cut saw unit with suction device incl. pneumatically swivelling saw blades, adjustable and programmable from the control pa ...

Fixed side at the left Panel thickness min/max: 16/45 mm Min. panel width: 150 mm Lateral panel support for panel width up to 900 mm Min/max. panel length: 700 / 3100 mm Max. laminate overhang: 110 mm Max. laminate thickness: 0,8 mm Radius min/max: 6 / 22 mm (depends the laminate) Feedspeed max. 18 m/min Top pressure by belt Equipment: Infeed fence, adjustable, defines the panel overhang 2 x trimming unit 0,4 kW, HSK 25 toolholder 1 x PVAc glue application 5 x glue nozzle, adjustable 1 x hot air blower 3 x IR heating on top (55 cm length), 3 x bottom (90 cm length) Postforming zone 1,8 m. length Various pre-installed profiling sets 1 x top trimmer 0,4 kW

Can filling line capacity: approx. 24,000 cph Filling Product: Soft drinks Can size: 330 ml and 500 ml standard cans Can Type: 211/202 consisting of: 1. Can depalletizer King with automatic can infeed system with Siemens S7 PLC including can table, pallet magazine, sheet removal system the depalletizer is fixed for the following pallet dimensions: 1.180 x 1.250 mm 2. Can rinser Transtech Hysek to rins new cans with filtered water infeed height: approx. 2,500 mm Outfeed Height: approx. 1,200 mm 3. Can filler and seamer KHS / Ferrum - Filler Innofill EMD 76 with 76 filling valves blocked with - Can seamer Ferrum type: F708G with 8 seaming stations the filler and seamer will be complete reconditioned in our workshop including new electric control panel with PLC Siemens S7 including Danfoss frequency inverter including beer pressure regulating valve including CIP  ...

2. VFDK-3 WALL TYPE CARTRIDGE FILTERED POWDER COATING BOOTH Wall-type powder coating booths are an economical manual powder coating booth solution for companies producing and powder coating small parts. These powder coating booths save space in the workshop and are a practical method of powder coating the work pieces to be painted. The wall-type coating booths can be combined with conveyors in transfer-type powder coating plants or have a simple conveyor line according to the project. WORKING PRINCIPLE The extraction fan is located at the top of the booth, at the end of the system. The pressurized air flow created by the fan carries the powder coating particles towards the filters and collects them on the outer surface of the filters. Powder coating filters are cartridge type and are cleaned during operation by a pull-reverse filter cleaning system. The pull-reverse system consists o ...

1. LIQUID SPRAY BOOTH The spray booth is designed for ventilation and filtering of paint overspray during manual painting application. VENTILATION SYSTEM Side draft ventilation provides high efficiency during paint application. The filter wall is manufactured modularly from galvanized sheet metal panels and the extraction fan is placed on the upper part of the filter wall and choiceed with plastic propeller to prevent the risk of spark formation. The electric motor is placed outside the extraction duct and there is no direct contact of the motor with the polluted air. FILTRATION SYSTEM The extraction filter is on the back surface of the spray booth filter wall and is used in 2 stages with 99.9% efficiency. In order to increase filtration efficiency, cardboard filter and paint stopper fibreglass filter are used as 2 separate layers. The warning lamp on the control panel indicates th ...

1. LIQUID SPRAY BOOTH The spray booth is designed for ventilation and filtering of paint overspray during manual painting application. VENTILATION SYSTEM Side draft ventilation provides high efficiency during paint application. The filter wall is manufactured modularly from galvanized sheet metal panels and the extraction fan is placed on the upper part of the filter wall and choiceed with plastic propeller to prevent the risk of spark formation. The electric motor is placed outside the extraction duct and there is no direct contact of the motor with the polluted air. FILTRATION SYSTEM The extraction filter is on the back surface of the spray booth filter wall and is used in 2 stages with 99.9% efficiency. In order to increase filtration efficiency, cardboard filter and paint stopper fibreglass filter are used as 2 separate layers. The warning lamp on the control panel indicates th ...

1. LIQUID SPRAY BOOTH The spray booth is designed for ventilation and filtering of paint overspray during manual painting application. VENTILATION SYSTEM Side draft ventilation provides high efficiency during paint application. The filter wall is manufactured modularly from galvanized sheet metal panels and the extraction fan is placed on the upper part of the filter wall and choiceed with plastic propeller to prevent the risk of spark formation. The electric motor is placed outside the extraction duct and there is no direct contact of the motor with the polluted air. FILTRATION SYSTEM The extraction filter is on the back surface of the spray booth filter wall and is used in 2 stages with 99.9% efficiency. In order to increase filtration efficiency, cardboard filter and paint stopper fibreglass filter are used as 2 separate layers. The warning lamp on the control panel indicates th ...

2. VFDK-3 WALL TYPE CARTRIDGE FILTERED POWDER COATING BOOTH Wall-type powder coating booths are an economical manual powder coating booth solution for companies producing and powder coating small parts. These powder coating booths save space in the workshop and are a practical method of powder coating the work pieces to be painted. The wall-type coating booths can be combined with conveyors in transfer-type powder coating plants or have a simple conveyor line according to the project. WORKING PRINCIPLE The extraction fan is located at the top of the booth, at the end of the system. The pressurized air flow created by the fan carries the powder coating particles towards the filters and collects them on the outer surface of the filters. Powder coating filters are cartridge type and are cleaned during operation by a pull-reverse filter cleaning system. The pull-reverse system consists o ...

Description: Type of edging Thin edge Thick edge Gluing System EVA Hotmelt Premilling Unit yes Corner Rounding Unit yes Max feed speed 11 m/min Maximum panel thickness 50 mm Operating Units 8 nr Min. panel height 8 mm Max. panel height 50 mm Min. edge thickness 0.4 mm Max. edge thickness 3 mm Max. forward feed speed 11 m/min Top pressure yes Panel support guides yes No. Panel Sizing / Milling units 1 NO. PANEL SIZING / MILLING UNITS 1 Unit : pre-milling unit automatic timed intervention : yes motor power : 2.2 KW Edge coil magazine yes no. positions 1 Gluing system yes glue pot for EVA hot melt glue yes Roller set to press the edge yes no. pressure roller 3 No. Edge Processing Units 5 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 motor power : 0.18 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : top and bottom rough trimming no. motors : 2  ...

Description: Work table height 1070 mm , linear speed panel conveyor with inverter min/max 40/90 m/min workpiece size panel width min/max (X) 250/3300 mm min/max panel depth (Y) 150/800 mm , min/max panel thickness 10/70 mm , max panel weight 50 kg maximum ratio between width (X) and depth (Y) panel 15/1  , tool size , maximum length 70 mm maximum diameter 10 mm maximum working diameter 35 mm  , machine body size 5500x2200x2300  , equipped with SCM control ES LCD monitor 17, 25 watts, 12 Vdc , PC HP PRODESK  , Pressure 6.5 bar 400 V and 50 Hz Approx. Onsite Dimension. (l x w x h): 6,000 x 6,000 x 2,900 mm, weight approx.: 6,600 kg

Description: serial number AB00022204 Max. panel length mm 3.050 min. panel length mm 200, Max. panel width mm 900 min. panel width mm 80, Max. panel thickness mm 60 min. panel thickness mm 10 max. X axis speed m/min 40, Max.Y axis speed m/min 40 vertical spindles - drilling head F14L (vers. P/PR) no. 8 (5X-3Y) - drilling head F23L (vers.P F23/PR F23) no. 13 (7X – 6Y) horizontal spindles - drilling head F14L (vers. P/PR) no. 6 (2+2X-1+1Y) - drilling head F23L (vers.P F23/PR F23 no. 10 (3+3X-2+2Y) rotating spindles motor power kW (Hp) 2,2 (3) spindle speed rpm 4.200 fixed integrated disc cutter (direction) X max. diameter of disc cutter mm 125 disc cutter rotating speed rpm 5.500 ELECTROSPINDLE motor power KW (Hp) 5,5 min./max. speed rpm 1.000/18.000 tool changer manual max tool diameter mm 20 for futher technical detail please consult document ,PDF STARTE ...

Description: Type of edging Thin edge Thick edge Solid wood Gluing System PUR Premilling Unit yes Corner Rounding Unit yes Grooving Unit yes Max feed speed 24 m/min Maximum panel thickness 60 mm Operating Units 9 nr Min. panel height 12 mm Max. panel height 60 mm Min. edge thickness 0.4 mm Max. edge thickness 20 mm Max. forward feed speed 24 m/min Top pressure yes Pressure with rubber belt Panel support guides yes No. Panel Sizing / Milling units 1 NO. PANEL SIZING / MILLING UNITS 1 Unit : pre-milling unit automatic timed intervention : yes Gluing system yes glue pot for PUR glue yes premelter for PUR glue yes premelter for PUR glue NORDSON Roller set to press the edge yes with positioning by NC yes No. Edge Processing Units 7 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 NO. EDGE PROCESSING UNITS 2 Processing Unit : top a ...

Description: Type of edging Thin edge Thick edge Solid wood Gluing System EVA Hotmelt Corner Rounding Unit yes Max feed speed 11 m/min Maximum panel thickness 55 mm Operating Units 7 nr Min. panel height 8 mm Max. panel height 50 mm Min. edge thickness 0.4 mm Max. edge thickness 8 mm Max. forward feed speed 11 m/min Top pressure yes Pressure with idle wheels Panel support guides yes No. Panel Sizing / Milling units 1 NO. PANEL SIZING / MILLING UNITS 1 Unit : pre-milling unit automatic timed intervention : yes motor power : 2.2 KW Edge coil magazine yes no. positions 1 Gluing system yes glue pot for EVA hot melt glue yes Roller set to press the edge yes No. Edge Processing Units 5 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming Constructor model : HL 6130 no. motors : 2 motor power : 0.18 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : fine trimming to trim  ...

The fishing and packing plants have a simple and this stable and torsion-free construction. The machines are characterized by ease of use, flexibility, reliability and low maintenance requirements. The CAMBORIT clip has a capacity of up to 125 packs / min. 1 x 2 bottles can be packed with the CAMBORIT clip. To do this from flat so called "bars" cut to shaped, that get caught under the edge of the bottle. The machine can be operated automatically or manually. Display and operating elements are located on the control panel. All functions are controlled from the control panel and controlled. Errors of the cycle are displayed on the control panel. Action: At the beginning of production the magazine must first cut to be filled. The minimum level is cut to the magazine below, the machine will not turn on. After switching on the machine when existing minimum level of bottles with a capac ...

Number of vertical independent spindles: 9 Number of horizontal spindles on axis X : (2+2) Number of horizontal spindle on axis Y: (1+1) N° 1 saw blade unit: (ø 100 mm) Router head 3,6 Kw ISO 30 - 12000/24000 rpm Max. thickness of the panel: 50 mm Control: Full Parametric Max weight of the panel: Kg 25 Max panel size: X ,Y 1100, Z 50 mm Min panel size: X 270,Y 150 (70 op.), Z 12mm Number of controlled axes: 3 Panel feeding speed: 25m/min Spindles speed rotation: 3600 rpm Saw blade speed rotation: 7000 rpm Air pressure: 7 bar Diameter of the dust extraction: ø 140 mm Exhaust air consuntion: (2000 mc/ora) - (30 m/s) Max drilling depth in horiz. on X and Y axis: 30 mm Max drilling depth in vertical: 45 mm Max horizontal diameter of the tools: 12 mm Max vertical diameter of the tools: 35 mm Motor power: 1,5 kw Max air consumption: 60 Nlt./min. Total power : 6,4 Kw  ...

machine 1: Fixed side at the left, working width 220 mm to 2500 mm Workpiece overhang max. 110 mm Electronic width adjustment Panel thickness 8 - 90 mm Top pressure by belts Rolling chain with automatic lubrication, automatic pop-up dogs every 1000 mm Feed speed 10 - 40 m/min Chain infeed taking 1,62 m. panels in front of the dogs Panel alignment at the infeed Middle support NC 30 controlls Equipment left and right: 1+1 Jump universal shaper 6 kW 1+1 Twin hogging unit, motors 6,6 kW (2 motors) 1+1 Universal shaper 6 kW 1+1 Jump universal shaper 6 kW panel turning device HOMAG TD 31/30/13 Year 1989 machine 2: Fixed side at the left, working width 220 mm to 3000 mm Workpiece overhang max. 110 mm Electronic width adjustment Panel thickness 8 - 90 mm Top pressure by belts Rolling chain with automatic lubrication, automatic pop-up dogs every 1000 mm Feed speed 8 - 40 m/min Chain infeed taking ...

faceplate diameter: 3200 mm swing diameter: 3500 mm turning height: 2200 mm range L-W-H: 7730 x 6240 x 6700 mm control: Typ 840 D sl voltage: 3 x 400 V frequency: 50 Hz turning speeds: 0,8 - 40 U/min max. turning diameter: 3500 mm total power requirement: 51 kW weight of the machine ca.: 86 t Technical specifications Machine type: CNC vertical lathe Manufacturer: Rafamet Year of manufacture: 1973 conventional General overhaul with control retrofit 2010 Control upgrade 2016 Control: Siemens 840 D Sl Condition: very good faceplate Turning diameter of the faceplate 3,200 mm Number of rotation stages of the face plate 3 (infinitely variable) Speed ranges of the faceplate 0.8 - 40 rpm Level I 0.8 – 3 rpm Level II 0.8 - 11 rpm Level III 0.8 – 40 rpm processing of workpieces Max. turning diameter 3,500 mm Max. turning height of the workpieces above the faceplate 2,200 mm vertical supports S ...

Pre-milling unit: yes; Pre-milling unit material removal: 0 - 2 mm; plastic edges: 0,4 - 3 mm; solid wood edges: 0,5 - 5 mm; Workpiece thickness: 8 - 50 mm; Minimum length of workpiece: 120 mm; Min. work piece width: 110 mm; Anti-adhesive spraying unit: yes; Edge preheating device: yes / with ceramic infrared lamp; Bonding unit: granulat / Glue container quick-change kit; Jack knife: yes; Flush trimming unit: yes; Corner copy unit: yes; Flush radius milling unit: yes; Radius scraper unit: yes; Area scraper unit: yes; Buffing unit: yes; Cleaning spray unit: yes; motor power: 5 kW; machine length: 3774mm; machine width: 1546 mm; machine height: 1337mm; weight: 842 kg; Top equipment for high productivity with low space requirements! Intuitive operation with the eye-S control and 10 large touchscreen: - HMI Maestro Active Edge - Graphic display of all processing units ...

Number of sanding units: 4 St sanding width: 190 mm Sanding height max.: 4-180 mm weight: 4200 kg Hess Expert 4-belt single wood sanding machine -------------------------------------- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimen ...

1. CONTAINER TYPE LIQUID SPRAY BOOTH Spray booth type : Side draft, enclosed type Air speed : 0,50 m/sec (empty spray booth) EXTERNAL DIMENSIONS Length (mm) : 6.058 Width (mm) : 2.438 Height (mm) : 2.591 INTERNAL DIMENSIONS Length (mm) : 5.900 Width (mm) : 2.350 Height (mm) : 2.390 SPRAY BOOTH BODY Entry doors : 2-leaf hinged door 1x leaf G3 filter for air inlet 1x leaf service and emergency door with a panic bar Body material : Mild steel and rectangular iron tube metar structure Insulation : 50mm PIR polyurethane filled sandwich panels, B1 class flammability Window : 2 set of 600 x 600mm waterproof PVC window Container base : Aluminum sheet, non-slip Lighting system : 2 pcs, 2x36W enclosed type armatures, Ex-proof Zone 2 Lifting : Lifting eyes at the top corner areas, forklift fork openings at the base HEATING SYSTEM Source : Electricity He ...

Code: 0226 Brand: FELDER - FORMAT4 Model: PERFECT 710 E-MOTION - CE Standard Automatic edge bander with grinding unit for edgebanding solid wood, chipboard, veneer, PVC, Abs, and melamine panels - CE Standard - Year 2010 Technical data: Min edge thickness 0,4 mm Max edge thickness 10 mm Max panel height mm 60 Max feed speed 12,5 m/min Top pressure bar: workpiece thickness adjustment is carried out electronically from the control panel Operating unit: infeed guide adjustable from control panel Grinding unit: with 2 diamond cutters Gluing unit with glue pot with quick-change system for processing EVA and PUR glue Edge pressure roller unit with 3 rollers with positioning from control panel End cutting unit consisting of 2 independent blades with high-frequency motors 12000 rpm - Tilting from 0 to 15° Multi-function end trimming unit with 2 motors 12000 rpm Edge scraper ...

Stainless steel switch cabinet, baying cabinet, 800x2300x600mm TS8450.600, Rittal, used Top Special price The current price of a similar product is € 3.600 excl. Mwst. If you have a VAT number, we will gladly issue you an invoice without VAT. We still have several identical and other such devices, but the amount is ending. Buy more than 1 piece, there is still a great discount. Stainless steel enclosure Nr.3, bayed enclosure, TS8450.600, Rittal, used-Top: - Baying cabinet width 800mm, height 2000mm, depth 600mm, - incl. cable routing shelves (raised floor) 200mm high - total height of enclosure + raised floor + adjustable feet = 2300mm - Material stainless steel 1.4301 - Incl. right side panel, rear panel and front door - Incl. mounting panel St galvanised (we can remove the mounting panel on request) - incl. 1 assembly panel St galvanised in the area of the trans ...

Pos. 2 - supply to the cooling tunnel, single-strand, equipped with cornering plastic flat-top chain, 82.5 mm wide; Scaffolding in stainless, Execution; complete with supports, railing brackets and guides as well as drive motor block in, Hollow shaft version, make SEW, type DRN®, 400/230 V, 50 Hz, IP55, energy efficiency class IE3;, the conveyor system is equipped with a pneumatic stopper/slider combination., This is how the rows are formed and pushed off., Item 3 – cooling tunnel, The system is based on a mat chain conveyor that is guided through a cooling zone., Technical specifications, Conveyor capacity: 750 pieces/h, Inlet temperature approx.: 80°C, Outlet temperature approx.: 35 °C, Average room temperature approx.: 10 °C, Cooling time approx.: 55 min, cooling belt, Usable chain width: approx. 1,200 mm, Usable chain length: approx. 4,200 mm, Inlet/outlet height: approx. 1,000 ...

Description: Max. panel height 60 mm Min. panel length 130 mm Min. panel width 65 mm Min. edge thickness 0.4 mm Max. edge thickness 3 mm Max. forward feed speed 30 m/min Pressure with rubber belt No. Panel Sizing / Milling units , Unit : pre-milling unit Constructor model : R3 L20 motor power : 4 KW r.p.m. : 9000 RPM Lamps to preheat the side of the panel , Edge coil magazine , no. positions 2 glue pot for EVA hot melt glue , premelter for PUR glue , Roller set to press the edge , no. pressure roller 5 No. Edge Processing Units 10 Processing Unit : end trimming Constructor model : 8,42/39/B no. motors : 2 Processing Unit : fine trimming to trim and round Constructor model : 08.055 Processing Unit : Corner rounding Constructor model : 08.342 Processing Unit : edge scraping Processing Unit : belt sanding Constructor model : 08.62 Processing Unit : belt sanding Const ...

Description: Max. panel width 3300 mm Min. edge thickness 0.4 mm Max. edge thickness 3 mm Max. forward feed speed 30 m/min Conveyor Track with dogs , Pressure with rubber belt NO. PANEL SIZING / MILLING , Unit : scoring unit motor power : 4.4 KW r.p.m. : 6000 RPM NO. PANEL SIZING / MILLING , Unit : double chipper, top and bottom Constructor model : 75.30 NO. PANEL SIZING / MILLING , Unit : miller hogger NO. PANEL SIZING / MILLING , Unit : miller hogger Edge coil magazine , no. positions 2 glue pot for EVA hot melt glue , premelter for EVA hot melt glue , Roller set to press the edge , no. pressure roller 5 No. Edge Processing Units , Processing Unit : end trimming Constructor model : 08.412 no. motors : 2 Processing Unit : fine trimming to trim and round Constructor model : 08.055 no. motors : 2 Processing Unit : Corner rounding Constructor model : ...

Description: serial number AH00004898 track feed speed 11 m/min panel thickness 8-60 mm thickness of edges in strips 0,3-6mm thickness of rolled edges 0,3-3 mm max. section of rolled edges 135 mm² coil-holder plate diameter 780 mm exceeding material to the panel thickness 2+2 distance between two successive panels 600 mm minimum panel length (100 mm min. width) 140 mm min. length of edge in rolls 180 mm min. length of edge in strips 220 mm min. panel width (210 mm min. length) 90 mm opening for panel support roller 500 mm worktable height 900 mm Betriebsspannung 400 V, 3 phases, 50 Hz nennstrom 29A leistung 10 kA for futher technical detail please consult document PDF - OLIMPIC K 360 HP.pdf  , serial number: AH00004898, Approx. Onsite Dimension. (l x w x h): 4,800 x 1,300 x 1,800 mm, weight approx.: 1,400 kg

Description: serial number: 36789 Technical specifications: total installed power 33 kW, 63A, 50Hz panel length - min 150 mm - max 3200 mm panel width - min 120 mm - max 3200 mm panel height -min 10 mm - max 60 mm edge thickness in the roll from 0.30 mm to 3 mm workpiece thickness from 10 mm up to 60 mm edgebanding strip height - min 15 mm - max 65 mm working line height 950 mm panel projection from drive belt 50mm adjustable feed speed from 10 m/min up to 24 m/min motorized height adjustment CNI control, display replaced with a flat screen anti adhesive spraying device joint cutting unit, 2 x motor 5kW, 12.000 rot/min edge feeder for roll, edge magazine for two edge rolls gluing unit for EVA adhesive, granulated 2 gluing units: 1 unit that apply the glue on the panel edge and 1 unit wich apply glue on the edge, for softforming applications. These units must change de ...

Description Brand Pro Froid Model Copeland Scroll ID SH4797 Status Active Year of manufacture 2010 Location Bucure?ti / Bucharest (RO) Old price: 13 500 Euro. 1. Refrigeration and Climate Circuit 1.1. Pro Froid (Franta) GC4/CCR3SH 4PCS15ZC/SC Packed air cool condensing unit: • 3 pcs. Semi-hermetic Piston Bitzer 4PCS 15.2Y compressors • 3 pcs. crankcase heater • 1 pc. Liquid receiver • 1 pc. HP and LP safety pressure switches • 3 pcs. HP safety pressure switches • 3 pcs. LP safety pressure switches • 3 pcs. electric panel boxes – IP 54 • 3 pcs. electrical engine protection devices • 3 pcs. Mounted valves on compressors • 1 pc. Automatic electric panel • 1 pc. oil management system 1.2. Electric and control panel 1.3. air cooled condenser S060 3MSC 6PH/6PL SV 1.4. Helpman / Alfa Laval coolers / ventilators / fans – 17 pcs. 1.5. Electri ...

Hünnebeck Manto 330 â?¢ Strong connection can be implemented by directional angle: 40 m ² of shell surface in a crane excavation without additional stiffening â?¢ highest bending strength due to the 14 cm high steel frame; Permitted concrete print 80 kN/m ² â?¢ rational shelling of large areas without compensation and with few anchoring points using MANTO XXL panels â?¢ Light and fast â or shelling of shafts with the MANTO chess corner â?¢ consistently good concrete image due to fire galvanizing of the frame and high-quality shakheads â?¢ Also suitable for shells finely skinned walls. 132m ²-EUR 19,969,60 Stocked: Table/Panel 90 x 330 â 20 Stk/pcs. Table/Panel 75 x 330 â 20 Stk/pcs. Inner corner/ash Inner Corner 35/330 â 6 Stk/pcs. Exterior ecke/Ou ...

Heavy duty refurbished grinder. Very robust construction. Rotor with staggered blades. Rotor diameter 400mm rotor length 700mm. Powered by 22kW electric motor. Complete with electrical panel with Siemens touch screen panel including inverter for the control of the grinder. This electric panel can also control a loading belt, exhaust fan, etc. The control was built in 2010 for internal tests and used for less than 100 hours. As an alternative, we can also fit a new e.motor 37kW on this grinder and manufacture a new control panel for the increased power at an additional cost. This special rotor with staggered blades is also particularly suitable for heavy applications and for grinding fibrous materials and textiles

OERLIKON / ALPHATOME II T30 HP300 PPM 400 OERLIKON - Typ: ALPHATOME II T30 HP300 PPM 400 - Baujahr: à 2013. Special features of the ALPHATOME II series / EQUIPMENT: Camera system: Moving camera on the cross-drive carriage for easy positioning and cutting monitoring by the operator from the control panel. The graphic is done by a permanently visible button on the touch screen interface. Protective devices: 7 Facilities for the protection of operating personnel. Photocells in the front and back of the bridge. Emergency stop button on all corners, as well as on the external control panel. Anti-glare-/splash protection: The anti-glare panel of the bridge is raised or lowered automatically or by pressing a button. On the sides, the panel can be opened manually for the burner and wear parts. Furthermore, the noise development is significantly reduced and resulting smoke is bet ...

Code: 0232 Brand: ALBERTI V. Model: DOOR / CN - Ce Standard CNC working centre for the complete machining of doors of any size or design - CE Standard The operating head is provided with different working units in order to allow all the door machining in one cycle only (i.e. sizing, squaring, aperture, lock groove, horizontal routings, hinges, anuba, etc.). Technical data: Working area : maximum panel dimensions mm 2500 x 1300 - minimum panel dimensions mm 350 x 140 Maximum panel thickness mm 60 Minimum panel thickness mm 12 N° 3 controlled axis Vertical router Hp 9 - ISO30 connection - rpm 18.000 Horizontal router Hp 4,5 , which can work on all 4 sides Horizontal router for locks Hp 2/3 - rpm 12.000/18.000 Tool stations fitted on the table n° 8 Vacuum pump with double-acting suction cups Working pressure bar 6/8 Suction hoods diameter 80-90 Machine overall dime ...

Professional vacuum packaging machine with stainless chamber, industrial pump, additional deep chamber and digital panel, possibility to connect to gas floor model PM-VC-400-UIG Manufacturer: Rotek, Austria; Digital panel for 50 operations and more additional functions; Built-in vacuum pump 20m³/h; Gas connection outlet/may not be used/; 2 strips for simultaneous sealing of two bags; 13 cm wide to 40 cm long at sealing seam; Deep camera – up to 260 mm; Automatic lid opening after packaging; Easy-to-use machine, with a stainless chamber with a lower cabinet and wheels for movement; For smaller bags, you can pack several together; Suitable for bags with a length of 40 cm. Through the digital panel, 50 different programs can be saved - for vacuum, for sticking, cooling time Vacuuming starts immediately after closing the lid and then the panel should ...

Microbiological protection and PCR cabinet with vertical air flow General characteristics Vertical hood with laminar flow, Class 100 is used for handling different samples in a sterile environment without turbulence and without impurities in the working room. Protects the work area both against microorganisms and other air contaminants, chemically toxic vapors and unpleasant odors, .. etc. Automatic electronic monitoring system controls all functions and all safety alarms of the system according to EU norms offers many working possibilities: 1) Overpressure system: part of the sterile air is evacuated through the front opening. 2) Pressure lowering system: part of the filtered air is evacuated while the outside air is partially brought inside creating a protective barrier without affecting the laminar flow. Protection of personnel and the environment, but can also be used for work ...

CEMENT PLANT BATCHING PLANT CONC. BATCH PLANT 210M3/HR-200KW BP210CMPH (Type I Portland Cement shall be used) Make: Hosan Engineering Co.,Ltd.Edit Make Model: HSBP-210MS Cement Plant control panel Silo tank- 2 units compressor water tank - 2 units Cement mixer Crusher plant Crusher 1 conveyor - 3 units crusher w/ wheels control panel Crusher 2 conveyor - 4 units crusher w/ wheels Control panel Concrete Hollow Block Plant Maker: Harex Eng’g Co. Ltd. Model: H212 mixer conveyor - 2 units Hollow block molder/press control panel Capacity: 210 m/ Hr Make: Hosan Engineering Co.,Ltd. Model: HSBP-210MS Capacity: 210 m/ Hr

4 up thermal CTP Kodak Magnus 400 p. 4up CTP IALDA laser head 2019 (no thermal head) Year: 2008 (Refurbished by Kodak in 2009) Plate counter reading 27,371 Current error: Plates are loaded incorrectly / registration is incorrect Incl. dongle, Prinergy Evo RIP, Windows XP computer Minimum panel format: 311 x 228 mm Maximum panel format 680x750 mm approx. 16 plates / h + Kodak Magnus 400 Conveyor Load manually Calculator including KODAK Preps HP xw4600 Workstation Windows XP Professional 2002 Intel® Core ™ 2 Duo CPU E8500 3.16 GHz 3.48 GB of RAM Kodak Preps 5.3 Kodak Mercury MK6 850 Year: 2005 (general overhaul 03/2009 by Kuhnen Media GmbH) Plate count: 22,977 3x 20L KODAK 400 xLo Plate Solution developer solution Maximum panel width: 850 mm Minimum panel length : 620 mm with middle developer rollers 320 mm (available) Plate thickness: 0.152 - 0.5 mm Wa ...

The NEW CNC grinding VERECO RG 700/8500 is designed for the batch production of bench pins and connecting rod pins of crankshafts in a fully automatic cycle, or, for the production of individual parts in manual. It operates by means of a mobile grinding wheel unit both on the X axis and on the Z axis: this allows the grinding of different diameters in a single positioning of the piece. MAIN TECHNICAL FEATURES: Distance between tips: 8500 mm Drill height: 800 mm Maximum rotating Ø: 1600 mm Maximum weight of the balance piece: 10,000 kg Maximum grinding wheel dimensions (with recesses): 1600x900x160 mm Approximate machine weight: 98.000 kg NB: The aforementioned technical data, collected from the technical data sheet of the manufacturer, are to be considered non-binding and subject to change without notice. NUMERICAL CONTROL The Siemens 840 D electronic numerical contro ...

Fixed side at the left Feedspeed 18 - 25 m/min Working width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mm Panel overhang 30mm Panel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations) Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mm Coil diameter 830 mm Equipment: Sprayers release agent Squaring device with 2 motors each 3 kW Edge heating Edge magazine for 2 coils, guillotine for edges up to 3 mm Glueing part A20 with quickmelt application Lateral pressure zone K, 1 driven and 6 after pressing rollers End trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kW Contour trimming, 2 exchange units Profile scraping PN10 Flat scrapers FA11 Sprayers cleaning agent Buffing Automation package straight/chamfer: -Automatic adjustment infeed fence -Automatic setting of pressure rollers -Pneumatic setting of end trims -Pneumatic setting of rough trims -Automa ...

Number of Bizerba scales: 4 pieces Power ratings: 3 x 400 V/ 50 Hz / 16 A technical documentation: available Availability: as of now composed of: - Sorting belt / separator with two Bizerba ST scales, weight range 0.04 to 6 kg, overall dimensions (L x W x H): approx. 2430 x 1530 x 1250 mm, width approx. 850 mm - simple conveyor belt (height adjustable), total length approx. 3650 mm, total width 510 mm, bandwidth approx. 250 mm - Control cabinet, control panel Siemens OP 73 (Simatic Panel), year of construction 2007 - tray dispenser, machine weight 64 kg, year of construction 2009, connected loads 230 V / 50 Hz, 16 A, overall dimensions (LxWxH): approx. 4750 x 880 x 1035 mm - Control cabinet, type GMS, year of construction 2008, operating pressure max. 8 bar, connected loads 3 x 400 V / 50 Hz / 16 A, control panel Siemens (Simatic Panel) - Sorting belt (height ad ...

GeneralIntegrated Mill Turn Center; Control: Control F31iB5 with CELOS CharacteristicsSwing- Ø, max.700 mmSpeed max.12000 rpmSlewability of B-Axis±120 degreeMovements X / Z / Y675/1562/300 (±150) mmMilling spindle upper side1 Bar diametre80 mmMax. Turning Length1530 mmSpeed max.4000 rpmMax machining diameter670 mmDrive power tool spindle5,5/3,7 kWDrive power milling spindle28/23 kWDrive power main spindle18,5/15 kWMovements X / Z200/1542 mmLower Turret10 PositionsNumber of Toolmagazine positions38 Weight approx.18500 KgCELOS - ERGOline TouchCELOS - ERGOline Touch to facilitate machine operation incl. 21.5 ERGOline Touch ® control with multi touch screens Uniform management, documentation and visualization of order, process - and machine data Networkable with CAD / CAM User friendly and p(Left Spindle) through-spindle hole dia. 91 mm, 4,000min-1 (STD)(Left Spindle) Through-spindle Hol ...

weight: 540 kg diameter: 1200 mm height: 1100 mm 0: 350 l total power requirement: 1,9 kW voltage: 350/50 V length in total: 1820 mm - with integrated manual separation ramp - control panel - Dosing pump for liquids - Capacity 382 liters - A soundproofing cover is also offered at extra cost! Sound insulation cover for VKUE 200 + The cover is controlled by a pneumatic piston + While the machine is running, the soundproof cover ensures for significant noise reduction. + It also prevents splashing of water or abrasives + It reduces noise emissions to less than 80 decibels. + The connection requires 6 bar General description: Our vibratory finishing system is suitable for: roughening, removing paint, decoating, deburring, derusting, descaling, de-oiling/degreasing, grinding as well as polishing and smoothing. The can also be used for non-metallic materials machine are used. Depending on the  ...

Net price: 4.400 € (excl. VAT) gross price: €5,236 (incl. VAT) - - - - - PTO generator 22 kVA with AVR -> More models with 18 - 80 kVA can be found in our other displays - - - - - - Manufacturer: Green Power (Italy) - - - - - Data of the PTO generator: - Generator manufacturer: MeccAlte (Italy) - Power: 20 / 22 kVA - Voltage: 230 / 400 volts - AVR ESC - Speed: 1500 rpm. - Dimensions: 80 x 60 x 98 cm (L/W/H) - Weight: 175 kg - - - - - Digital Display: - Volt - Display (V) - Hertz - Display (Hz) - Operating hours - Meters - - - - - Requirements for the tractor: - PTO speed: 430 rpm - Recommended tractor power: 40 hp - - - - - Sockets: - 1x 400V 32A socket - 1x 1-phase socket 230V 16A - - - - - House - Field - Panel - The "House Field Panel" shown in picture 2 can be ordered for an extra charge - Switcher between home operation ...

Net price: 4.800 € (excl. VAT) gross price: €5,712 (incl. VAT) - - - - - PTO generator 33 kVA with AVR -> More models with 18 - 80 kVA can be found in our other displays - - - - - - Manufacturer: Green Power (Italy) - - - - - Data of the PTO generator: - Generator manufacturer: MeccAlte (Italy) - Power: 30 / 33 kVA - Voltage: 230 / 400 volts - AVR ESC - Speed: 1500 rpm. - Dimensions: 80 x 60 x 98 cm (L/W/H) - Weight: 220 kg - - - - - Digital Display: - Volt - Display (V) - Hertz - Display (Hz) - Operating hours - Meters - - - - - Requirements for the tractor: - PTO speed: 430 rpm - Recommended tractor power: 60 hp - - - - - Sockets: - 1x 400V 32A socket - 1x 1-phase socket 230V 16A - - - - - House - Field - Panel - The "House Field Panel" shown in picture 2 can be ordered for an extra charge - Switcher between home operation ...

Net price: 5.850 € (excl. VAT) gross price: €6,961.50 (incl. VAT) - - - - - PTO generator 50 kVA with AVR -> More models with 18 - 80 kVA can be found in our other displays - - - - - - Manufacturer: Green Power (Italy) - - - - - Data of the PTO generator: - Generator manufacturer: MeccAlte (Italy) - Power: 42.5 / 50 kVA - Voltage: 230 / 400 volts - AVR ESC - Speed: 1500 rpm. - Dimensions: 115 x 75 x 110 cm (L/W/H) - Weight: 360 kg - - - - - Digital Display: - Volt - Display (V) - Hertz - Display (Hz) - Operating hours - Meters - - - - - Requirements for the tractor: - PTO speed: 430 rpm - Recommended tractor power: 80 hp - - - - - Sockets: - 1x 400V 63A socket - 1x 1-phase socket 230V 32A - - - - - House - Field - Panel - The "House Field Panel" shown in picture 2 can be ordered for an extra charge - Switcher between home op ...

Net price: 6.650 € (excl. VAT) gross price: €7,913.50 (incl. VAT) - - - - - PTO generator 66 kVA with AVR -> More models with 18 - 80 kVA can be found in our other displays - - - - - - Manufacturer: Green Power (Italy) - - - - - Data of the PTO generator: - Generator manufacturer: MeccAlte (Italy) - Power: 60 / 66 kVA - Voltage: 230 / 400 volts - AVR ESC - Speed: 1500 rpm. - Dimensions: 115 x 75 x 110 cm (L/W/H) - Weight: 440 kg - - - - - Digital Display: - Volt - Display (V) - Hertz - Display (Hz) - Operating hours - Meters - - - - - Requirements for the tractor: - PTO speed: 430 rpm - Recommended tractor power: 120 hp - - - - - Sockets: - 1x 400V 125A socket - 1x 1-phase socket 230V 32A - - - - - House - Field - Panel - The "House Field Panel" shown in picture 2 can be ordered for an extra charge - Switcher between home op ...

Net price: 7.250 € (excl. VAT) gross price: €8,627.50 (incl. VAT) - - - - - PTO generator 80 kVA with AVR -> More models with 18 - 80 kVA can be found in our other displays - - - - - - Manufacturer: Green Power (Italy) - - - - - Data of the PTO generator: - Generator manufacturer: MeccAlte (Italy) - Power: 75 / 80 kVA - Voltage: 230 / 400 volts - AVR ESC - Speed: 1500 rpm. - Dimensions: 115 x 75 x 110 cm (L/W/H) - Weight: 450 kg - - - - - Digital Display: - Volt - Display (V) - Hertz - Display (Hz) - Operating hours - Meters - - - - - Requirements for the tractor: - PTO speed: 430 rpm - Recommended tractor power: 150 hp - - - - - Sockets: - 1x 400V 125A socket - 1x 1-phase socket 230V 32A - - - - - House - Field - Panel - The "House Field Panel" shown in picture 2 can be ordered for an extra charge - Switcher between home op ...

UK Power Generators Ltd have in stock the container for the generators to be inserted and perform their energy production operations. Ideal for Jenbacher 320,316, 314 312 series generators Available for sale... The empty container with highly specialised flooring and walls considering the equipment to be installed in there. The container pictures are attached to this advert, as seen it has a separate panel room for the breaker panel, control panel. Everything inside the empty container excluding the breaker panel is included in the sale. Please write to us at Infoukpowergeneratorsltd for further information on arranging viewing or pricing details. ~ UK Power Generators Ltd

Control cabinet, standard control cabinet, with cooling unit OSTERWALDER 1200 x 600 x 2000 mm width: 1200 mm, height: 2000 mm, depth: 600 mm 2 doors, 1 side panel, 1 side panel as control panel, rear panel removable cooling unit: PFANNENBERG DTS 720 Power consumption: 0.8 / 1.0 kW 230 V 1 AC 2.6 A used, tested ! Dimensions: 1340 x 630 x 2050 mm

Fixed side at the left Feedspeed 18 - 25 m/min Working width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mm Panel overhang 30mm Panel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations) Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mm Coil diameter 830 mm Equipment: Sprayers release agent Squaring device with 2 motors each 3 kW Edge heating Edge magazine for 2 coils, guillotine for edges up to 3 mm Glueing part A20 with quickmelt application Lateral pressure zone K, 1 driven and 6 after pressing rollers End trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kW Contour trimming, 2 exchange units Profile scraping PN10 Flat scrapers FA11 Sprayers cleaning agent Buffing Automation package straight/chamfer: -Automatic adjustment infeed fence -Automatic setting of pressure rollers -Pneumatic setting of end trims -Pneumatic setting of rough trims -Automa ...

Control unit, control panel, control panel, control unit, keyboard, screen, control -Siemens: Profinet connection box PN Plus -On the control panel: with additional panel holder/emergency stop button -Price: per piece -Number: 4 pieces -Dimensions: 420/350/H1220 mm -Weight: 30 kg