other machines and plants used for sale (14,194)

nursing homes, accommodation, Modules can be put together.

Cat.-No. 15-00071 new for sterile aseptic warehousing and outsourcing for KZE Tanks KZE-fitting complete connection DN 40 right – 90° bow welded filter and butterfly valve DN 15 180° bow double pipe clamp DN 40/15 Air G-DN 25 li-FSV G-DN 25 DIN 11864 for gases 0,5 bar lifting device + cleaning Below SV DN 40 VA – Handle at the front manometer up K/M DN 40 AISI 304 Weight: 8 kg Surcharge for filter cartridge Pall Emflon 0,2 € 100,-- All prices are valid Ex-Works, excl.VAT Freight Charges: depending on dimensions and destination Delivery: from 97753 Karlstadt-Karlburg Subject to prior sale Please visit our Web-Site: www.eurolux-ag.com

Cat.-No. 15 00059 new Measurements and Weight: Length: 1730 mm Width: 570 mm Height: 1340mm Weight: 300 kg Characteristics of the drive: Spur gear transmission: - Transmission 38 /min Screw rotational speed (output speed) 12-50 /min Electrical Data: - Power 5,5 kW - Rotational speed 1450 /min - Current consumption ~ 11A - Voltage 3/PE/400 V - Frequency 50 Hz Machine power: max. 80 kg/h of purifies rape seed Operating Instructions available All prices are valid Ex-Works, excl.VAT Freight Charges: depending on dimensions and destination Delivery: from D-97753 Karlstadt-Karlburg Subject to prior sale Visit our Web-Site: www.eurolux-ag.com

Ladies and gentlemen, Offer: approx. 4,000 m2 residential complex offered in mobile construction, which could be available at short notice. If you are interested, I would be pleased. With a friendly greeting Trade & Translations

IN STORAGE - Capacity: 38 mm ? 152 mm dia. bar Length: 2.4 m ? 11.5 m 38 mm ? 216 mm dia. tube Speed: 20-180 FPM at 17° Pass line: 927 mm Rolls: 1 straight roll dia. 508 mm ? 660 mm width Roller bearings Drive: 150 HP motor, 400/1200 RPM, 250 V DC Gearbox: Total ratio 5.13:1 high 15.4:1 low sheave ratio 2:1 Dimensions: 6400 x 5530 x 184 ? L x D x H Features: Trough & pusher buggy Entry guides Total line length: 30 m

Used pneumatic press for cheese made by Spomasz Rzeszow. New 2006. Available 2 pcs.

Used vacuum pump made by TEPRO Koszalin with a central vacuum. Unit that has two points of connection, the machine very little exploited.

Bevel scale Manufacturer: Toledo Year of construction: 1972 Capacity: 10 kg - 320 kg Part 1, section: 200 gr In good condition!

Steelyard with tare balancing device Manufacturer: Pfister scales GmbH Augsburg Type: N 300 Minimum load: 50 kg Maximum load: 2000 kg Mass Bridge: 1.5 m x 1.25 m In good condition!

Bevel scale Manufacturers: Bizerba Minimum load: 10 kg Maximum load: 500 kg 1 tick: 200 gr Scale is in working and in good condition!

Mixing system on steel construction with ring trogm (150 l. useful filling, 5.5 kW drive, 0.55 kW motorized outlet), bucket lift (1.5 kW drive, incl. winch, rope and rails) and control cabinet. Hardly used after revision, very good condition.

Inclined lift with motorized winch (7.5 kW / 36 UPM), lifting bucket (1,000 l. usable volume), weighing frame / foot station (2,000 kg max.), 25 m rope and head station for material transfer. Rope and SEW winch drive are new; Elevator was used to feed an Eirich intensive mixer type R(V) 18. Technical documentation is available.

Stainless steel pipe screw with 250 mm diameter and 2,100 mm conveyor length (measured from mid inlet to middle outlet), inlet and outlet 270 mm each, with drive via intermediate gearbox and claw coupling.

Pipe conveyor screw with 270 mm diameter and 2,900 mm conveyor length (measured from center inlet to middle outlet). Drive 5.5 kW via intermediate gearboxes of gearbox construction north and claw coupling. Tree speed: 49 UPM; Spiral pitch: 130 mm.

Pipe conveyor screw with 270 mm diameter and 5,000 mm conveyor length (measured from center inlet to middle outlet). Drive 5.5 kW via intermediate gearboxes of gearbox construction north and claw coupling. Tree speed: 49 UPM; Spiral pitch: 130 mm.

Pipe conveyor screw with 270 mm diameter and 5,200 mm conveyor length (measured from center inlet to middle outlet). Drive 5.5 kW via intermediate gearboxes of gearbox construction north and claw coupling. Tree speed: 49 UPM; Spiral rise: 125 mm.

Robust rotary valve with inlet and outlet diameter 275 mm, drive via gear motor 0.25 kW / 35 UPM. Several identical locks available (Built between 2000 and 2007), very good condition, partly unused.

Used lifting column unloader of the trays with a mechanical device used to unload the container process granules distributed on trays. The device is equipped with a shredder granules. The device has a complete DTR manufacturer. Specifications: max. capacity: 160 kg Tray size: 35x600x1000 mm max. number of trays: 8 max. process container height: 1300 mm prod.1997 year max. External dimensions: height. 3080 mm, width. 1550 mm, 1820 mm length Material: AISI 316 / AISI 304 implementation class: EEx e II T 3

PRODUCT LENGTH: 3-36 M, TRAVERSE DISTANCE: MAX. 31 M, 0.6 M/SEC.,

ULTRASONIC INSPECTION - TESTQMATIC - TYPE: SPA-2N, L=5-60 M, 1 M/SEC., 1988 EDDY CURRENT INSPECTION - MPA - 1989 RAIL PROFIL MEASURING DEVICE - SCHMITZ & SÖHNE AND BSB - 1989 PRODUCT HEIGHT: 95-165 MM, HARDWARE & SOFTWARE

Used jaw crusher Makrum company, type 40.17 Specifications:   1.Wielko inlet -800x1000 mm.   2. The adjustment range of the gap outlet - 80/18 mm.   3. Max. the size of the input material - 750 mm.   4. Performance - 35-90 m3 / h   5. The power of 75 kW drive motor.   6. The weight of the largest unit 14 T.   7. Weight crusher 38.1 T. Jaw crushers are used for crushing of hard and mean, for example. Basalt, granite, metal ores, quartz, glass cullet, limestone, sandstone, cement clinker, etc. These materials may not have a clay-loam dirt more than 5%, and humidity more than 10%. Wide range of sizes crushers and their technical parameters allow you to apply them in different nodes crushing - from the initial node crushing until the final product.

Used Makrum cone crusher company, type 44.51. Available 2 pieces. In addition, two new cones. Cone crushers are used for crushing of hard and mean, for example. Basalt, granite, metal ores, diabase, quartz, limestone, sandstone, cement clinker. These materials may not may not have a clay-clay impurities in an amount greater than 5% and a humidity of more than 10%. Crushers are used to prepare the materials for the construction of roads, railway embankments, as well as pre-grinding materials, subject to further processing in other devices, eg. In mills. Hydraulic cone crushers have internal support team cone crushing. Adjusting the exit slot is controlled hydraulically, and read from the console. Hydraulic overload protection automatically disappearance of the inner cone and its return to the original position after the resignation of overload.

Propeller agitator Manufacturer: Stelzer Type: propeller agitator Technical data: Engine power: 11 kW Speed: 1.450 U/min Frequency: 50 Hz Wave length: 60 cm Shaft diameter: approx. 6 cm In very good condition!

Propeller agitator Manufacturer: Stelzer Type: propeller agitator Wave length: 64 cm In very good condition!

Ladies and gentlemen, we can offer you pre-produced components for roads on request in order to build short-term system roads. All prices are from Station Europa and the dismantling and all follow-up costs are to be made by the buyer. VAT is not included in the prices; The contractual agreements for the individual offers must be agreed separately and only apply after the contract has been legally signed. Mistake reserved. All technical details; Measurements, etc., are approximate information and are non-binding for the provider. The technical data are manufacturer or operator information and therefore non-binding for us. Used material is sold to the exclusion of any warranty; We do not accept any liability for used material. Warranty exchange and return are excluded. Customer protection is agreed between the parties. The entire process of dismantling, loading and transport is carri ...

Swing mill for iron-free grinding or micronizing of chisels (solid sum content 70 - 78%), grinding chamber lined rubber, drive 22 kW. Task size: Up to 5 mm; final fineness: 4 microns. Last used grinding body: 7.5 to. Cylpebs, 20 mm x 20 mm (not included).

Cat.-No. 14.00230 in very good condition Cat.-N°: 14-00230L available: 1 unit 115 m tube in AISI 304 DN 40 Mount according to your Specifications Other Sizes upon Request Measurement and weight: total height: 400 mm Width: 700 mm total length: 3000 mm weight: 185 kg All prices are valid Ex-Works, excl.VAT Freight Charges: depending on dimensions and destination Delivery: from D-97753 Karlstadt-Karlburg Subject to prior sale General terms and conditions listed on our website. Prices are subject to change without notice. Visit our Web-Site: www.eurolux-ag.com

Extrusion press with 400 mm , drive 55 kW, hard casting screw wings and pre-press PZSVG 40 (Built 1996, drive 15 kW), on 4 hydraulic spindles. Complete with 1 spare part set screw and reel.

Stainless steel chimney Dimensions: Height: 23.5 m Diameter: approx. 1 m Material: 1.4301 (V2A) Chimney consists of two parts each 12 meters, which are screwed! Frames run to top thin-walled. Construction: Frames length: 2 meters Material thickness of frame: Skirt: 8 mm (steel) Following two frames: 6 mm (1.4301) Following two frames: 4 mm (1.4301) Remaining frames: 3 mm (1.4301) In very good condition!

Hydrostatic pressure transmitter with metallic measuring cell Manufacturer: Vega Grißhaber KG Type: D36G 0.2 EXB Continuous level measurement by means of a hydrostatic Pressure transmitter with metallic measuring cell in compact design with Threaded connection, flexible cable extension as well as one in the sensor housing built-in two-wire electronics with analog signal transmission 4 ... 20 mA/HART suitable for a separate evaluation device e.g. type VEGAMET 381 Ex. Scope The pressure transducer is a pressure transmitter for pressure and level measurements of liquids and viscous fillers with higher temperatures in the chemical, food and pharmaceutical industries. The pressure transducer offers the possibility to detect even the smallest measuring ranges from 0.1 bar. Your benefits - Highest measurement reliability even at rapidly changing process temperatures - High ...