mobile shear used for sale

Bombled 2100 x 2 mm Max sheetthickness: 2 mm Cuttinglength: 2100 mm

Qty. 1 Second-hand strip rolling mill Mfc.: United Engineering Type: 4-Hi Built: Strip Width: 393 mm (15.5”) Thickness Entry: 4 mm (0.16”) Exit: 1.2 mm (0.05”) Mill Speed: 405 m/min. (1330 Fpm) Strip Tension: 2670 kg (5875 Lbs) Coil ID 406 mm (16”) Coil OD 1448 mm (57”) Coil weight: 3180 kg (7000 lbs)

Used JMC 407 Kat Alligator Scissors Alligator scissors JMC 407Cat The catalyst version JMC 407 has an additional "V-holder" in the cutting area for adjustment when cutting or opening the catalysts. In stock at the end of March 2021 Knife length: 407 mm Measuring opening: 250 mm Cutting capacity: 90 tons Round iron ST 37: 57 mm diameter Number of strokes at 1/4 opening: 63 / min Number of strokes at full opening: 11 / min Dimensions (L x W x H): 1550 x 880 x 1120 mm Weight: 880 kg Drive: 7.5 kw / 380 V Operation: Foot pedal

No. 3554: 1 gebr. Table scissors Fabr. SCHARRINGHAUSEN, type HS/S, Bauj. 1952 Arb.-Ber.: 2050 x 2 mm, Other: adjustable rear stop 600 mm good condition

Max. diameter 240 - 2000 Max. plate thickness 10 mm Main motor power 5,5 HP

Key data: 3100 mm, 6 mm

HACO TS 3006 hydraulic guillotine shears manufactured in Belgium in 2006, are used in manufacturing plants to cut steel sheets with a maximum length of 3100 mm and a thickness of 6 mm. The machine has vertically aligned knives with four cutting edges, which ensure high precision and quality machining of workpieces regardless of the thickness and type of sheet. The angle of the cutting knives and the gap between them are adjusted by means of two levers at the rear of the machine. During machining, the workpiece is pressed against the cam in order to take an accurate measurement on the gauge located between the front stop and the bottom knife. Two parallel hydraulic cylinders drive the cutting bar (the upper knife attached to the slider) to perform the movement in the up-down direction. The HACO guillotine shears are offered with equipment which includes a foot control, a modern HACO SP ...

Description Table shears from Weipertsuitable for tools, fixture construction, training and mould making Cutting length 3200mm Sheet thickness 16mm Technical data Sheet thickness (max.) 16 mm Working length 3,080 mm Extension 150 mm Cutting angle 0.3 - 2.5 degrees Strokes per minute 14 h/min Holder 18 pieces Holder pressure capacity 40 t Table dimensions 3.380x550x840 mm Backstroke Backstop depth 1,000 mm Front support arms Number of support arms 3 pieces Length of support arms 900 mm Drive power Engine power main drive 37 kW Hydraulic oil tank volume 350 l Dimensions and weights Dimensions (length x width x height) 4x2.2x2.42 m Weight 15.300 k

Cutting lenght 6000 mm Cutting thickness 12 mm

Hand lever shears, hand tin snips, tin snips, sheet metal snips -Scissors: 240 x 4 mm -Transfer in current condition as seen -Dimensions: 400/150/H1200 mm -Weight: 46 kg

Cable shears -Cable shears: hydraulic -without: hydraulic unit -Max. Opening: 95 mm -Number: 1x cable shears available -Dimensions: 530/180/H80 mm -Weight: 13.3 kg

Long knife, sheet metal and round steel shears -Sheet metal shears: stable -Material: flat steel -Round: up to 15 mm -Square: up to 15 mm

Baykal 3000 mm x 10 mm NC Guillotine Shear Machine is in good condition

Ozamech hydraulic guillotine, bending length 3000mm Used machine efficient, sale due to liquidation of the company.

Scrap scissors hydraulic with petrol engine

Hydraulic guillotine shear model Atlantic 3012 very good condition. - Year of manufacture - 1990. - Length of the cut sheet - 3000mm. - Max cutting thickness 12mm - The machine is equipped with an automatic bumper. - The machine has 1 set of spare original knives. - Weight 8000 kg.

Durma MS 3004 Guillotine Shear Machine is like new condition

Folding table at the rear 12mm aluminum / 8 steel thickness Sharpening knife CNC Backgauge Opening Stroke 190mm

Dener DMMH-NC/31-10 Guillotine Shear Cutting length : 3100 mm Maximum cutting thickness : 10 mm Machine is in good condition

Cutting length : 3100 mm Cutting thickness : 10 mm Machine is in good condition

Durma SBT 3006 CNC Guillotine Shear Cutting length : 3000 mm Maximum cutting thickness : 6 mm Pneumatic sheet support

Durma SBT 3010 CNC Guillotine Shear Machine is in very good condition

Durma VS 3020 CNC Guillotine Shear Maximum cutting thickness : 20 mm Cybelec control unit Stroke : 190 mm Number of cut per minute : 7-13 Machine is in good working condition

Punching force : 30 Ton Sharing Force : 25 Ton Machine is in excellent condition

Hydraulic panel shears - storage machine - incl. foot switch, touch screen, rear installation room with light barrier monitoring, automatic/electric cutting gap, automatic/electric cutting angle, hydraulic hold-down, mot. Backgauge up to 1000 mm depth -Illustrations similar- Hydraulic plate shear - storage machine - incl. foot switch, touchscreen, rear set-up area with light barrier monitoring, automatic/electrical cutting gap, automatic/electrical cutting angle, hydraulic hold-down, mot. backgauge up to 1000 mm -images similar-

Cutting length : 3000 mm Maximum cutting thickness : 6 mm Machine is in good condition Machine can be sold as set with press brake : https://www.makinaalsat/makinalar/172773/durmazlar-abkant-pres

Baykal HNL 3100x10 mm CNC Hydraulic Guillotine Shear Adjustable angle Cutting length: 3100 mm Maximum cutting thickness : 10 mm Machine is in good condition

Ermak CNC HVR 3100 x 10 CNC Guillotine Shear Machine is in very good condition

Esa S 530 Control Unit Folding length : 3100 mm Cutting thickness : 6 mm

Durma SBT 3006 Hydraulic Guillotine Shear Cutting length : 3100 mm Cutting thickness : 6 mm Machine is in good condition

Durma CNC HGM 6013 Guillotine Shear Machine is in good condition Cutting length : 6000 mm

Durma DHGM 3016 NC Guillotine Shear Cutting length : 3100 mm Maximum cutting thickness : 16 mm

Durma AHGM 6016 NC Controlled Guillotine Shear Cutting length : 6000 mm Maximum cutting thickness : 16 mm New blades Machine is in working condition

Cutting length : 4100 mm Cutting thickness : 16 mm Number of cuts per minute : 5 Power : 30 Kw Machine is in good condition

Cutting thickness, mm - up to 8; Cutting length, mm - up to 4050; Cutting angle, mm - 1.5; Number of hydraulic clamps, pcs - 17; Cuts per minute (metal / stainless steel) - 13/20

Cutting length : 3000 mm Max. cutting thickness : 13 mm Machine is in good condition

Machine is in good condition but you need to order new Control Panel! Maximum cutting length : 3100 mm Maximum cutting thickness : 20 mm

Baykal MGH 3110 NC Guillotine Shear Number of cut per minute : 11 Motor power : 22

Baykal MGH 3100 x 16mm NC Guillotine Shear Cutting length : 3100 mm Maximum cutting thickness: 16 mm Number of cuts per minute: 8 Motor power : 30 Kw

Durma 6100 mm x 16 mm CNC Guillotine Shear Cutting length : 6100 mm Maximum thickness : 16 mm Machine is in good condition

: neu : ca. 12 Wochen ab Auftrags : 1280 mm : 16 mm : 12 mm : 8 1/min : 3 ° : 7 pcs. : 500 mm : 22.5 kW : 250 l : 950 mm : 2100 mm : 1400 mm : 2000 mm : 5000 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

I.MA.l CCOSI CNC shear in excellent condition. Used machine visible in Italy, sold as it is

stroke 340 mm stroke in a minute 6-10 /min lubrikant capacity 400 lt motor 30 kW

Cutting length : 6100 mm Max. cutting thickness : 16 mm All maintenance has been done recently Motorized table is included in the offer

Cutting length 3,050 mm. Max. thickness 6.3 mm St 235 There is a set of spare knives for the scissors The scissors are fully operational and are in use.

: neu : ca. 8 Wochen ab Auftragse : Spanien : 170 to : 40x40x4 mm : 65x65x7 mm : 2 : 25/5 bzw- 18/7 mm : 350 to : 5 kW : 265 bar : 70 l Automatic line for punching and sharing angle STANDARD EQUIPMENT: INFEED/OUTFEED CONVEYERS idle rollers 3 conveyers each 3,3 m for feeding angles up to 12 m length WORKING UNITS: ROLLER FEED MEASURING SYSTEM feed by roller wheel (brushless moto),rotary encoder no time loss for measuring feeding speed variablefrom 0 to 36 m/min positioning accuracy in X axis0,25 mm + 0,15 mm per meter the last 250 mm can not be used PUNCHING UNIT (2X) 1 punching unit per leg 1 punch per punching unit adjustable back mark by tooling fromfrom 20-40 mm hydraulic downholder direct access for quick change ofpunches and dies SHEARING UNIT shearing power 350 kN single cut direct access for quick change ofshearing blade hydraulic downholder CNC CONTROL OMRON PLC colour touchscree ...

: neu : ca. 12 Wochen ab Auftrags : 1530 mm : 16 mm : 12 mm : 7 1/min : 3 ° : 8 pcs. : 500 mm : 22.5 kW : 250 l : 950 mm : 2350 mm : 1400 mm : 2000 mm : 5200 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 28 min. Punching force: 110 to : 40x20 mm flat steel: 600x15 oder 400x20 mm L-beam 90°: 160x160x16 mm L-beam 45°: 70x70x7 mm : 50 mm square edge steel: 50 mm : 13 mm throat: 300 mm Basic equipment: - Complete set of blades for flat steel shears - Complete knife set for bar cutter - Complete knife set for angle steel shears - Compl. Standard punching device - Stamp quick release device for punches up to 40 mm diameter - Rectangle notch compl. with hold downs - Complete knife set below for rectangular notching - Upper tool for rectangular notching - Support table for flat material - Punching table with stop - Notch with stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

flat steel: 350 x 10 mm round bar steel: 35 mm square edge steel: 30 mm L-beam: 80x80x8 mm hole diameter in sheet thickness: Ø 27 in 13 bzw. Ø 20 in 8 mm : 500 kN throat: 177 mm : 34 (Hub 15mm) blade length: 356 mm engine output: 3.0 kW weight: 950 kg dimensions: 1300x1100x1850 mm Standard equipment: - Knife set for flat steel - Complete knife set for angle steel shears - Complete normal punching equipment - Quick release device for punches up to 31 mm - Support table for punching device, rectangular notching and flat steel shears - Bending stamp with matrices V 40 and V 70 - Electric contact stop (1.000 mm) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Durma VS 3006 CNC Guillotine Shear Cutting length : 3000 mm Cutting thickness : 6 mm 3000X6mm +-0.05 cutting accuracy Machine is in good working condition

sheet width: 3100 mm plate thickness: 10 mm cutting angle: 2 ° down holder: 14 Stück no. of strokes: 13 Hub/min throat: 350 mm oil volume: 260 l total power requirement: 22 kW weight of the machine ca.: 10.550 kg dimensions of the machine ca.: 4000x2250x2050 mm Domestic equipments: - Hydraulic swing cut sheet metal shears - Touch screen controller with digital display for backgauge - automatic kerf adjustment via the control - Backgauge control 1000 mm travel with recirculating ball screws - Vibration cutting machine with kerf adjustment - 2 support arms - 1 side stop - Photocell behind the machine - Cutting length limit - cut line lighting - Chrome steel knife - Ball rolls in the table - hinged finger guard with limit switch - Footswitch - CE mark / Declaration of Conformity - Bed instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTe ...