mini cone used for sale

PSU PC 1 NSV 80 (Grundig 9.44904-1705 FD-Nr. 6006 04 100640) Exchangeprice 500,-€ with Exchange 600,-€ Features of our PCB are - A new built up PCB with technology SMD (No PCB revised for many years) - Where it was possible electrolytic capacitors were substituted with ceramics - Components for repair the next decades available - Newer and more efficient components. -Doubling of the source capacity -Less warm development etc. Their advantages are -Cost reduction on a minimum -The newest technology in the usual control -Spare part availability the next decades guaranteed -No consequential costs by decades old repaired PCB

CPU PC 1 NPP 80 (Grundig 9.44904-1903 FD-Nr. 6006 04 100641) Exchange 710,-€ + Mwst without Exchange 810,-€ + Mwst Features of our PCB are - A new built up PCB with technology SMD (No PCB revised for many years) - Where it was possible electrolytic capacitors were substituted with ceramics - Components for repair the next decades available - Newer and more efficient components. -Doubling of the source capacity -Less warm development etc. Their advantages are -Cost reduction on a minimum -The newest technology in the usual control -Spare part availability the next decades guaranteed -No consequential costs by decades old repaired PCB

The monitor is conceived so he at few minutes of the operator independently after the enclosed instructions it can be exchanged. The control timing is preset i.e. the monitor is ready for use immediately. Micro-adjustments can be changed about the self explicatory menu ON SCREEN arbitrarily by customer wish.The connections for the graphics signal are by a conector 20pol. he can not wrong are put on is able marked. The monitor TFT is fastened to the same points like the original monitor and this guarantees easy installation.

Input Board PC 2 NE 90 (Grundig 9.44904-1708 FD-Nr. 6006 04 100662) Exchange 400,-€ + Mwst without Exchange 500,-€ + Mwst Features of our PCB are - A new built up PCB with technology SMD (No PCB revised for many years) - Where it was possible electrolytic capacitors were substituted with ceramics - Components for repair the next decades available - Newer and more efficient components. -Doubling of the source capacity -Less warm development etc. Their advantages are -Cost reduction on a minimum -The newest technology in the usual control -Spare part availability the next decades guaranteed -No consequential costs by decades old repaired PCB

Input and Output Board PC 2 NEA 90 (Grundig 9.44904-1709 FD-Nr. 6006 04 100663) Exchange 480,-€ + Mwst without Exchange 580,-€ + Mwst Features of our PCB are - A new built up PCB with technology SMD (No PCB revised for many years) - Where it was possible electrolytic capacitors were substituted with ceramics - Components for repair the next decades available - Newer and more efficient components. -Doubling of the source capacity -Less warm development etc. Their advantages are -Cost reduction on a minimum -The newest technology in the usual control -Spare part availability the next decades guaranteed -No consequential costs by decades old repaired PCB

Used rebuild KHD Humboldt Wedag model S3?01 decanter. New 1992. Cylinder made of hardened steel (it does not rust but not stainless) lenght of cylinder 1370 mm, cone lenght 110 mm. Screw made of steel also hardened. Drum speed 2200 rpm. Motor 30 kW with clutch dydrodynamic made by Voith (easy start). Lubrication by ump. New bearings casindgs, transmission belts, all bearings are new, seals. During the rebuild drum and zscrew ware balanced. Suport fram with antivibrators. Manual available in Polish. Capacity approx. 20000 L/H.

Euroblock 12 movable block machine offers a very wide production range of concrete products. It can be used as a universal machine as well as special product making machine. This multi-purpose block machine can be used for the production of: Hollow blocks Chimney blocks Hourdy blocks Insulated blocks Garden blocks Solid blocks Curbstones Paving stones with or without face mix Layers separated by plastic foil or by sand. With its standard safety devices, rigid frame construction that allow heavy duty use, and simplicity of design that reduce maintenance to a minimum, this machine is the most economical choice for a very wide range of concrete products manufacturers. Useful area: 1290 x1130 mm (product height 170 ? 250 mm) Useful area: 1290 x900 mm (product height 250 ? 500 mm)

Used standing on 3 feet of pipe stainless steel container made of V2A, 1.4301 - WSt - container with upper edge reinforcement Content: 300 LTR. Diameter: approx. 660 mm Zyl. Height: 900 mm Total height with feet: 1.500 mm Open top containers. Container with bottom cone base. on the cover: 1 threaded socket DN 50 1 socket ½ " in the middle of the subfloor: 1 spout front pulled about NW 50 otherwise com. photo in very good condition!

Qty. 1 Second-hand ingot caster plantMfc.:Sistem TeknikBuilt:1/2015Stopped in 4/2015Recycling capacity:5000 Ton/annumQty. 12 Units of Pyrotek moldsDim. of aluminium ingot: 1000 x 1000 x 500 mmWeight:500 kgCharging material: Aluminium cans, profiles, sheets, motor blocks, wheels etc.Scope of supply:Aluminium shredderMagnetic separator Aluminium de-coating machine Baler Aluminium gas furnace Aluminium casting system Gas generator Mass ARUN spectrometer Air compressor, conveyors, forklift, ect.Shredder and magnetic separation conveyorMfc.:YSSType:Mono shaft shredder J600Capacity:500 kg per hour high power electrical shredding machineMono shaft shredder stylePLC automatic control unit Siemens?Hydraulic unit for material pushing to shredding wheelCurrent control for shredder reverse †safe usageShredded aluminium pass onto conveyor unitMagnetic separation system for steel removalElec ...

ABB Arc Guard TVOC-2-240 Arc Flash Guard COMPLETE SET Built 2012 The new retail value for these parts is Euro 8500,- Like new, only been used for 3 years. 6x complete set available. -- TVOC-2-240 - ABB TVOC-2-240, ARC MONITOR W/HMI, 100-240VAC/DC The Arc Guard TVOC-2 builds on the well-appreciated TVOC design and offers unmatched arc monitoring. With over 35 years of experience, Arc Guard System has become an industry standard in several key markets, helping to protect personnel and businesses around the world. The TVOC-2 is an optical detection system that together with an external breaker can limit the damage done to personnel and equipment in case of an arc accident happening. Main benefits Increased safety to personnel and equipment Minimizes downtime after arc accident has happened Easy-to-read interface makes reading status information quick and easy Simp ...

1 factory-tested, very well preserved double girder crane with 4 wheels per side to minimise wheel loads Load approx. 100,000/32,000 kg Wingspan approx. 26,700 mm Hook way approx. 14,000 mm Make SKET-year of manufacture/overhaul/workshop test 1981/2000/2016 Very low equipped with high-quality two-rail wind work trolley with main hub usage as a mounted crane 100 t and auxiliary hoist 32 t, cabins - and radio control, ideal wheel load distribution by 4 wheels per side working speeds: Hoist main hoist 100 t up to 0.25/2.5 m / min auxiliary hoist 32 t up to approx. 7.0 m / min Trolley gear approx. 7.0/20,0 m / min Crane chassis approx. 11.0/32.0 m / min

Used press for powder made by Vetraco, model CP 012. Capacity 200-800 pcs. / H depending on the size of the bowl and the formula powder. New 1996. Press 163x85x150 without housing Table 74x46x50 Net weight: 800 kg Engine: 5.5 kW Power supply: 380 V, 9 A, 50 Hz Compressed air a minimum of 5 bar Matrix Upper: 150x150x15 / 17.5 Matrix middle: 150x150x17 Matrix lower: 116x116x12,2 / 38.2

Heating capacity: 10,5 kW Max. Temperature: 350 ° C maximum capacity: 12 ltr. 380 V / 50 Hz protection class IP 54. Pressure vessels: 9 kW 12 bar 4.2 ltr. Max. Operating temperature: 350 ° C Minimum flow rate: 0,4 m³ / h

Producer: Sorgo Description: -Sorgo Smokehouses -One room for two trolleys -One main door -Powered by steam -Dimensions; 1450 mm x 2480 mm x 2700 mm -Higth needed to install 3100 mm -Total weight 1380 kg -Steam conection: 2-4 bar -Water conection: 4 bar -Air conection: 6 bar/40l/h -Electric conection; 3/MP, 50 Hz, 380 V, 220 V -Smoke generator dimensions; 1350 x 450 x1100 -Work options; drying, cooking, cooling, smoking, infusing -Seting control by mikroprocesor Mikster (brand new) with warranty -In excelent condition 2 machines available.

Preliminary operating machine for year QIV/2013, 100 operating hours Basic 1530 Basic Waterjet Processing Centre 1530 Working area: X-axis 3050 mm Y-axis 1550 mm Z-axis 150 mm The abrasive water jet cutting requires the addition of a supplied abrasive cutting head. This reduces the distance between cutting head and factory tool. drives: drive side, reverse play-free linear drives in X and Y are used with stoeration-free CAN-BUS communication as well as guide well-known manufacturer. This This means maintenance and wear-free operation of the system and the long -term Drive unit X-axis is mounted on granite. Individual linear units are protected by folding beam and covers in addition to the ingress of dust and water. Accuracy: 0.05 mm / Working area Max.Speed: 15,000 mm/min Z axis German-speaking operator software for machine control Abrassiv de-sludge plant ...

Ueberholungsjahr 2016 Baujahr 2010 Saegeblatt Hartmetall 500 mm Antriebsleistung Saegemotor 7,5 KW Drehzahl Saegemotor 2000-38000 min-1 Schnittgeschwindigkeit Saegeblatt 3100-6000 mm/min Saegeblattvorschub stufenlos Einstellbar 0-40 mm/ s Arbeitsbereich 90° max.:460 x 50 mm Nachschublaenge Pneumatisch: Einzelhub:max. 300 mm Servogesteuert: Einzelhub:max. 300 mm Mehrfachhub:max. 9999mm Nachschubgeschw. Servogesteuerte Nachschubeinheit 300 mm/s Druckluftanschluss bauseits 6 bar Gewicht(Saege)ca.: 1000 Kg Abmessungen LxBxH(Saege)ca.: 2100mm x2000mm x1600mm Hydraulikagregat) ca.: 900mm x600mm x800mm Technische Beschreibung Pressta Eisele Profilma 540 Retrofit Pressta Eisele Profilma 540 Retrofit Vollautomatischer Hochleistungs-Saegeautomat fuer NE-Metall und Kunstoffe Die Maschine befindet sich nach abgeschlossenem Retrofit sowohl technisch als auch op ...

Bevel scale Manufacturers: Bizerba Minimum load: 10 kg Maximum load: 500 kg 1 tick: 200 gr Scale is in working and in good condition!

Steelyard with tare balancing device Manufacturer: Pfister scales GmbH Augsburg Type: N 300 Minimum load: 50 kg Maximum load: 2000 kg Mass Bridge: 1.5 m x 1.25 m In good condition!

FOR SALE SULZER ASV 25/30 ENGINE NEW GENUINE SPARE PARTS AT TURKEY HAVE A GOOD DAY SIR. WE HAVE MANY NEW GENUINE SPARE PARTS OF SULZER ASV 25/30 ENGINE AT OUR STOCK. WE VE 200 ITEMS AT OUR STOCK. PLS FIND 100 ITEMS WITH PARTS NUMBER ON BELOW. IF YOU INTEREST PLS DO NEED HESITATE TO CONTACT WITH US.. NO. ONE - SULZER 12 ASV 25/30 PART NO. 1 NEW CYLINDER LINER 5001001 1 PCS 2 NEW PISTON 3404001 4 PCS 3 NEW CAM SHAFT SECTION 10107001 3 PCS 4 NEW COMPLETE LUBRICATION PUMP 30004 K 1 PCS 5 RECON CONNECTING ROD 1 PC 6 NEW LOWER CRANK BEARING D = 225 MM 02103 B 7 PAIRS 7 NEW UPER CRANK BEARING D = 225 M 02103A 7 PAIRS 8 NEW BEARING SHELL HELPED D = 195MM 03004A 12 PAIRS 9 NEW THRUST BEARING HELPED 2103001 2 PAIRS 10 NEW BOLT WITH OVERSIZE 701007/0VERSIZE 12 PCS 11 NEW BEARING SHELL HELPED D = 195MM 03004A 12 PAIRS 12 NEW BEARING SHELL HELPED D = 194.5MM 03004B 511200- ...

Manufacturer: UNION - Gemany Model: BFT 130 / 5 Condition: very good New in.: 1978 / 2000 , the machine was completely modernized for Company ALSTOM Control: conventional with Heidenhain Linear readings in 3 axes Technical details: Spindle diameter: 130 mm Spindle speed: 4.5 - 900 rpm Spindle cones: MORSE 5 ( the price of the machine will deliver free of charge adapter for ISO 50 ) X axis: 1600 mm Y axis: 1600 mm Z axis: 2500 mm W axis: 1000 mm Table: 1600 x 1400 mm Table Rotation: 360 Charging the table: 8000 kg Speed: 4.5 to 180 rpm Power range: 0.63 to 2000 mm / min Fast forward: 2 m / min Total required power: 35 kW Approximate Weight: 47000 kg EQUIPMENT: Heidenhain readings line in three axes, flat disc

Depositors from Bosch Manufacturer: Bosch type: GSH 5031 B Year of manufacture 2002 With the Bosch GSH 5031 B, they get a machine that creates a vertical or horizontal pillow packs in cartons. Maximum speed: 180 bags / min 10 cartons / min Bag dimensions (mm) minimum (length x width): 100 x 70 maximum (length x width): 400 x 250 maximum height (thickness): 80 Carton dimensions (mm) (open) minimum (length x width x height): 180 x 70 x 60 maximum (length x width x height): 500 x 350 x 450 If you have questions you can me any time call on mobile: 01718367957

used approx. 4 m³ / 4000 litres polyester tank / fibreglass tank / transport tank above ground, standing at 4 feet, good condition dimensions: T = 1.80 m x W = 1.30 m x H = 2.40 m (without feet) The tank includes 4 steel feet/cones, dome on the front of the front, several in - and outlets. The container can be used as storage tank for juice, canola oil, water, liquid food, whey, potato steam skins, molasses, liquid manure, AHL, ASL, as rainwater tank, etc. Price upon request. Transport can be arranged at low cost. Also we can modify the tank to suit your demands, just ask us. It is not possible to update all our advertisements daily. Since our inventory is changing continuously, it may be that this tank has already been sold but a similar one is in stock. Please give us a call or write, so that we can advise you personally. More information and offers on our site ...

Minidose packing machine Made in Spain for small dose of sauces, olive oil, powder, hot caramel. The machine is new one and can be prepared for any kind of liquid, powder, granulate. PLC and screen. Electric photocell. coding machine. Further information please contact

The Velati F4 continuous meat cutter, made entirely from stainless steel, has been designed to transform a block of meat into meat pieces, using a blade system specially devised to avoid damaging or crushing the meat. A combined blade structure, consisting of an oscillating guillotine blade and circular saw blades, allows the meat to be processed at various temperatures and cuts both the lean and fat meat. The machine can produce up to 8-10 tons per hour. Velati meat cutter is driven by a conveyor, whose speed can be adjusted via a variator, allowing both the hourly production rate and the thickness of the cut pieces to be controlled. Velati meat cutter is equipped with inverter which regulate the feed belts. The F4 models is equipped with touch-screen control and PLC which can configure and store the different work programmes. The machine is also fitted with a safety system that is cont ...

Machine according to DIN 8605: lathe with increased accuracy. Top width: 700 mm Tip height: 170 mm Swing over bed: Ã? 340 mm Swing over cross slide: Ã? 190 mm Bed width: 260 mm Longitudinal slide displacement: 600 mm Cross slide displacement: 220 mm Upper carriage displacement: 110 mm Plan carriage length: 410 mm Plan slide width: 150 mm Bed slide length: 380 mm Turning tool cross section: 20 x 20 mm Distance turning Center - upper carriage: 34 mm Range of the upper carriage (support): 60 / 120 ° Main spindle: Spindle connection DIN 55029 (camlock): S 5 spindle bore: Ã? 50 mm Internal cone according to DIN 7178: 1:22 spindle diameter in front bearing: Ã? 70 mm Maximum Chuck diameter: Ã? 200 mm Faceplate diameter: Ã? 200 mm Spindle speeds: 40-3000 rpm Speed: Stepless mechanical speeds: 4 Main drive: Power at 40% ED: 5,3 kW Maximum nominal torq ...

used approx. 2 m ³ / 2,000 litres polyester tank, GRP tank, transportation tank, Juno-tank, good condition Dimensions: L = 1.66 m 1.10 m = B; H = 1.50 m (without feet). H = (total) 1.75 m Aboveground vertical tank, incl. 4 steel feet/cones, dome on the front, several in - and outlets. The container can be used as a storage tank for water, liquid feed, whey, potato steam skins, molasses, liquid manure, AHL, ASL, seeping juice, canola oil, or as a rain drip tank, etc.. Price upon request. Transport can be arranged at low cost. Also we can modify the tank to suit your demands, just ask us. It is not possible to update all our advertisements daily. Since our inventory is changing continuously, it may be that this tank has already been sold but a similar one is in stock. Please give us a call or write, so that we can advise you personally. More information and offers  ...

Used approx. 3 m³ / 3,000 litres polyester tank / GRP tank, transportation tank, Staffelstein tank, good condition. Dimensions: H = 2, 00 m (tank) H = 2, 50 m (total) W = 1, 00 m L = 1, 60 m (tank) L = 1, 70 m (total) Overground, upright tank, incl. 4 steel feet/ cones, dome on the front, several in- and outlets. The container can be used as a storage tank for water, liquid feed, whey, potato steam skins, molasses, liquid manure, AHL, ASL, seeping juice, canola oil, or as a rain drip tank, etc.. Price upon request. Transport can be arranged at low cost. Also we can modify the tank to suit your demands, just ask us. It is not possible to update all our advertisements daily. Since our inventory is changing continuously, it may be that this tank has already been sold but a similar one is in stock. Please give us a call or write, so that we can advise you personal ...

Artec mini table lathe C2x300 tips size 300 mm + 8 PCs chisel set Mini table lathe C 2 and 8 PCs. HSS cutters set now in the Westfalia savings Kit. C-2 the spindle speed variable from 200-2500 RPM via a potentiometer is adjustable at the mini lathe. About a 80 mm three-jaw chucks can be clamped workpieces easily. The workpieces can be supported with a tailstock with MK 2-recording. By a quad-steel holder the cutters can be secured, designed for 8 mm cutters. Also thread can be cut with this mini lathe 1.5 mm pitch. All materials with normal strength can be edited. (Aluminium brass steel). Technical data: centre height 90 mm centre distance 300 mm spindle bore 19 mm tailstock intake MK-2 thread cutting range 0.2 1.5 mm speed range 200-2500 U / min variable power 250 Watt/230 V Plan route 65 mm Oberweg sled 55 mm Quill trail 50 mm Dimensions Lxwxh approx. 700  ...

Technische Daten: - Hobelbreite 20 - 200 mm - Hobelhöhe 8 - 200 mm - minimal Werkstücklänge 590 mm (einzeln) / 250 mm (bei Serie) - 4 Spindeln - Spindel FI 40 mm - Drehzahl 6800 U/min - Vorschubgeschwindigkeit stufenlos 8 - 33 m/min - Abrichtwelle, unten max. Werkzeug FI 125 mm - Rechte Vertikalwelle max. Werkzeug FI 110 - 180 mm - Linke Vertikalwelle max. Werkzeug FI 110 - 180 mm - Dickenwelle, oben max. Werkzeug FI 108 - 180 mm Spindelfolge: 1. unten 5,5 kW 2. rechte vertikal 5,5 kW 3. linke vertikale 5,5 kW 4. oben 7,5 kW - Motor Vorschub 4,0 kW - Motor Höhenverstellung 0,75 kW - Gesamtleistung 28,75 kW - Aufgabetischlänge 1600 mm - Druckluftanschluss max. 6 bar - Absaugstutzen 4 x 120 mm - Abmessungen L=3270, B=1700, H=1750 mm - Gewicht 3300 kg inklusive: - hart verchromte Tische - CE Norm, TÜV Rheinland - motorisch angetriebene Walzen im Tisch - pneumatischer Andruck der V ...

You are looking for replacement parts for your cone mixer? We have the most common spare parts for various products such as E.g. Nautamix, v mix, Vrieco-mixer etc. in stock, or they can customize quickly and cost-effectively in our workshop. -Mixing augers -Spare or replacement transmission -Spare or replacement swing arms - gears, shafts, seals -Top bearings -Universal joints -Radial storage -Outlets -Etc. In addition, we have a repair and maintenance service. We like to submit a non-binding offer. E-mail: t.roechter@heiligbv

V-mix, Nautamix, Vrieco-, NAUTA mixer, cone mixer N.M. Holiness B.V.. spare parts Second-hand machine You are looking for replacement parts for your cone mixer? We have the most common spare parts for various products such as E.g. Nautamix, v mix, Vrieco-mixer etc. in stock, or they can customize quickly and cost-effectively in our workshop. -Mixing augers -Spare or replacement transmission -Spare or replacement swing arms - gears, shafts, seals -Top bearings -Universal joints -Radial storage -Outlets -Etc. In addition, we have a repair and maintenance service. We like to submit a non-binding offer. E-mail: t.roechter@heiligbv

Technische Daten: - Hobelbreite 20 - 200 mm - Hobelhöhe 8 - 125 mm - minimal Werkstücklänge 590 mm (einzeln) / 250 mm (bei Serie) - 5 Spindeln - Spindel FI 40 mm - Drehzahl 6800 U/min - Vorschubgeschwindigkeit stufenlos 8 - 33 m/min - Abrichtwelle, unten max. Werkzeug FI 125 mm - Rechte Vertikalwelle max. Werkzeug FI 108 - 180 mm - Linke Vertikalwelle max. Werkzeug FI 108 - 180 mm - Dickenwelle, oben max. Werkzeug FI 108 - 180 mm - Zweite Welle, unten max. Werkzeug FI 108 - 200 mm Spindelfolge: 1. unten 5,5 kW 2. rechte vertikal 5,5 kW 3. linke vertikale 5,5 kW 4. oben 7,5 kW 5. unten 5,5 kW - Motor Vorschub 4,0 kW - Motor Höhenverstellung 0,75 kW - Gesamtleistung 34,25 kW - Aufgabetischlänge 1600 mm - Druckluftanschluss max. 6 bar - Absaugstutzen 5 x 120 mm - Abmessungen L=3500, B=1780, H=1750 mm - Gewicht 3600 kg inklusive: - hart verchromte Tische - CE Norm, TÜV Rheinland - m ...

really well maintained, equipped with simple CNC control. Saw blade diameter 400 mm This section at 90 ° round 130 mm rectangle 240 x 85 mm flat 180 x 70 mm in MITRE at 45 ° profiles Portrait 120 x 55 mm Feed length with double lifting device to 2 cutting speeds 10/20 m / min. Speed infinitely variable 0-1000 mm / min. Drive motor 400 V, 1.7/2,6 kW Weight 1350 kg Dimensions W x D x H 2750 x 1500 x 1900 mm Accessories: Spray cooling device "Mini pos 807", Blade, roller conveyor, manual.

1 DETTIN hydroextractor for cones type BERTA 24 hydraulic type

Hydraulic Type Manufactured by Angelo Cremona Maximum Diameter 800 mm Minimum Diameter 120 mm

Demonstration device. The system is designed to work in a closed circuit. It has two separate chambers / phases, the first chemical solution and the second with soapy water. The device is designed to minimize the effort of mixing of substances. A micro-processor controlled system allows easy operation of the unit with a user interface. Inside / work Maß 2000 B x 1500 T x 1500 H Outer dimensions 2800 B x 1600 T x 1800 H Operated electrically Voltage 380 V Power 9 kW Frequency 50-60 Hz Water pressure 60 / 160-200 bar Chemical pressure up to 15 bar Phase I chemistry circuit closed heated chemical tank Phase II water / tap water Capacity 7-10L/min Heating capacity 30 80 ° C Tank capacity 200 L Control manual / automatic Remaining warranty up to 12 months Continuously exhibition equipment on sale

Technische Daten: - Hobelbreite 20 - 230 mm - Hobelhöhe 8 - 160 mm - minimal Werkstücklänge 840 mm (einzeln) / 400 mm (bei Serie) - 6 Spindeln (5+Uni) - Spindel FI 40 mm - Drehzahl 6000 U/min - Vorschubgeschwindigkeit stufenlos 6 - 36 m/min - Abrichtwelle, unten max. Werkzeug FI 125 mm - Rechte Vertikalwelle max. Werkzeug FI 200 mm - Linke Vertikalwelle max. Werkzeug FI 200 mm - Dickenwelle, oben max. Werkzeug FI 180 mm - Zweite untere Welle max. Werkzeug FI 200 mm - Universalspindel max. Werkzeug FI 160 mm - Drehzahl Universalspindel 6800 Upm Spindelfolge: 1. unten 5,5 kW 2. rechte vertikal 5,5 kW 3. linke vertikal 7,5 kW 4. oben 7,5 kW 5. unten 7,5 kW 6. Universalwelle 7,5 kW - Motor Vorschub 5,5 kW - Motor Höhenverstellung 0,75 kW - Gesamtleistung 47,25 kW - Aufgabetischlänge 2000 mm - Universalwelle 360C schwenkbar - Druckluftanschluss max. 6 bar - Absaugstutzen 6 x 150 mm - Abm ...

4 factory-tested, very well preserved double girder cranes Load approx. 20.000 kg Wingspan approx. 16.650 mm Hook path about 5.000 mm Fabrikat MAN/SWF Year of production/workshop test 1995/2016 Cranes equipped with SWF double girder trolleys with reduced design to minimize the installation height, freely movable floor control Working speeds: Hoist approximately 0.32/3.2 m / min Katz LG 5.0/20,0 m / min Crane chassis 10.0/40.0 m / min

Technical data: hydraulic undertable circular saw unit - drive power motor 7.5 kW- diameter saw blade Z=48x5 600 mm- diameter saw blade bore 30 mm- inclined working table Yes- Automatic rotation of the table -70C 0C+70C- Speed of rotation from / to 0C / 70 C 3s- Positioning accuracy +/- 0.2C- Pneumatic workpiece holder 2 pieces- Pneumatic side organizers 2 pieces- Safety cover via capping unit Yes- Cutting capacity at 0C: 160 x 310 mm, 80 x 390 mm- cutting capacity at 45C: 160 x 220 mm, 80 x 270 mm cutting capacity at 70C: 160 x 90 mm, 80 x 130 mm- minimum workpiece thickness 10 mm connection values - supply voltage 400 V / 50 Hz- Control voltage 24 V compressed air requirement at 8 bar per cycle approx. 8 Nl- Suction nozzle FI100 mm 2 pieces- Suction nozzle FI160 mm 1 piece- air speed Suction in center of nozzle approx. 25-35 m/s Electronically controlled slider:- Loading length: 6000 m ...

Bag inserts from Bosch Manufacturer: Bosch type: GSH 5031 B Year of manufacture 2002 With the Bosch GSH 5031 B, they get a machine that creates a vertical or horizontal pillow packs in cartons. Maximum speed: 180 bags / min 10 cartons / min Bag dimensions (mm) minimum (length x width): 100 x 70 maximum (length x width): 400 x 250 maximum height (thickness): 80 Carton dimensions (mm) (open) minimum (length x width x height): 180 x 70 x 60 maximum (length x width x height): 500 x 350 x 450 If you have questions you can me any time call on mobile: 01718367957

Bag inserts from Bosch Manufacturer: Bosch type: GSH 5031 B Year of manufacture 2002 With the Bosch GSH 5031 B, they get a machine that creates a vertical or horizontal pillow packs in cartons. Maximum speed: 180 bags / min 10 cartons / min Bag dimensions (mm) minimum (length x width): 100 x 70 maximum (length x width): 400 x 250 maximum height (thickness): 80 Carton dimensions (mm) (open) minimum (length x width x height): 180 x 70 x 60 maximum (length x width x height): 500 x 350 x 450 If you have questions you can me any time call on mobile: 01718367957

Demonstration device. Powder coating plant mini - for beginners The spark / ROMER® powder coating plant mini - consists of: SLS-9 small powder furnace (Indoor: 1200x1400x1200mm - without transport system) Powder booth KPZ-2 p Powder hand plant AP 400 Shipping costs will be calculated individually. (also, pickup) Payment conditions: 30% deposit and the balance of 70% with notification of readiness for dispatch.

Technische Daten: - Hobelbreite 20 - 200 mm - Hobelhöhe 8 - 125 mm - minimal Werkstücklänge 590 mm (einzeln) / 250 mm (bei Serie) - 6 Spindeln - Spindel FI 40 mm - Drehzahl 6800 U/min - Vorschubgeschwindigkeit stufenlos 8 - 33 m/min - Abrichtwelle, unten max. Werkzeug FI 125 mm - Rechte Vertikalwelle max. Werkzeug FI 108 - 180 mm - Linke Vertikalwelle max. Werkzeug FI 108 - 180 mm - obere Horizontalwelle max. Werkzeug FI 108 - 180 mm - zweite obere Horizontalwelle max. Werkzeug FI 108 - 180 mm - zweite unter Horizontalwelle max. Werkzeug FI 108 - 200 mm Spindelfolge: 1. unten 5,5 kW 2. rechte vertikal 5,5 kW 3. linke vertikale 5,5 kW 4. oben 7,5 kW 5. zweite oben 5,5 kW 6. zweite unten 5,5 kW - Motor Vorschub 4,0 kW - Motor Höhenverstellung 0,75 kW - Gesamtleistung 39,75 kW - Aufgabetischlänge 1600 mm - Druckluftanschluss max. 6 bar - Absaugstutzen 6 x 120 mm - Abmessungen L=4000 ...

MADO MEW 620 Automatic Grinder, performance 1400kg/h, bowl capacity 35kg, stainless steel construction, Unger Cutting System reduces handling and minimizes heat rise. You are very welcome to inspect and test the machine in our facility in Koblenz, Germany.

- for Walterwerk Kiel Jupiter baking oven - for different angles and cone lengths

-Die BBS 550 ist ideal zum Schneiden von weichem, hartem, trockenem oder gefrorenem Holz bzw. Holz-Prismen  mit einer Länge entsprechend der Maschinenkonstruktion. -Die max. Schnittlänge ist abhängig von den Verlängerungselementen -Alle Holzarten können mit dem gleichen Sägeband geschnitten werden. -Robuste und schwingungsfreie Konstruktion -Minimaler Wartungsaufwand -Einfache Bedienung Massive Präzisionsgusslaufräder -Präzisionsführungen -Excenterspanner -Vorschneiderschwenkmechanik -Manuelle Schnitthöheneinstellung -Manueller Vorschub -Geliefert mit 4,6 m Rollbahn Technische Daten: - max. Stammdurchmesser: 550 mm - max. Brettbreite: 530 mm - max. Sägebandhub: 20 mm - max. Schnitttiefe: 220 mm - Schnittlänge Grundversion: 3,7 m - Verlängerungssektion: 2,3 m - max. Schnittlänge: unlimitiert - min. Schnnittlänge: 0,9 m - Motorleistung Antriebsrad S1 (100%) / S6: 4 kW / 5, ...

Oel-Diffusion pump Manufacturer: Leybold Type: DIP 50,000 Status: used Technical data Product: DIP 50000 Catalogue: 22240 Connection flange Suction side: DN 1000 ISO-F Connection flange Print side: DN 160 ISO-K Suction Below 1.0 x 10-4 mbar / 7.5 x 10-5 Torr: 50000 l/s working range: 1.0 x 10-2 - 5.0 x 10-7 mbar 7.5 x 10-3 - 3.8 x 10-7 Torr Final pressure: < 5.0 x 10-7 mbar < 3.8 x 10-7 Torr Max. pre-vacuum pressure: 6.0 x 10-2 mbar 4.5 x 10-2 Torr Equipment: Pump is delivered without equipment quantity of equipment min.: 12.0 l 12.7 qt max.: 25.0 l 26.4 qt grid connection: 3-ph Y, 400 V, 50/60 Hz Heating capacity: 24 kW Number of heating cartridges: 24 Heating time: < 30 min Number of cooling water circuits: 3 Cooling water minimum pump: 1500 l/h 6.6 gal/min Duesenhut steam barrier: 150 l/h 0.66 gal/min Max. Cooling water pressure: 6 bar 87 psi Cooling water connection pump: 1/ ...

Guide machine Manufacturer: SATO Type: SATRONIK G 1500 Control: CNC 3010 Size: 4000 x 1500 mm Year of construction: 2008 operating hours: 8,090 h (machine on) plasma plasma Source Manufacturer: Kjellberg Type: Hi-Focus 280i Additional equipment: Automatic gas control PGV 3 Year of construction: 2008 operating hours: 728 h (plasma jet on) suction system Manufacturer: Donaldson Type: Torit DCE, DFPRO 6-CYCLO Year of construction: 2008 to visitunder electricity Very good condition mining and commissioning on request; ready for immediate use

Creo Lotem 400, year 2005 830 nm fully automatic thermal imaging plate setter model: Lotem 400 quantum head 4 page format 3 cassette MCU Minimum plate size: 381 x 318 mm Max plate size: 750 x 622 mm F speed: 16 plates/hour resolution: up to 2540 dpi approximate number of plates produced: 100950 Bacher control 2000 punch Excellent condition

We are offering original spark plugs for engines CAT/MWM TCG 2020 minimal order is for 10 pieces for 432 EUR/piece for Biogas engine spark plugs, and 488 EUR/piece for Naturalgas engine spark plugs.