milling plant used for sale

Fine grinding plant consisting of: Alpine 630 AFG fluidized bed counter-jet mill (V ges: 885 dm3, 10 bar pressure-shock-resistant, saerterrad fold-out), feed station, cyclone, 2 pcs. EX-protection valve, control cabinet and 4 pieces of product buckets. Previous use: Grinding of toner. The system can be inspected in a disassembled condition. Available at an additional cost: Dust filter Bühler PGFG 60/18 (39 m2 filter area).

We provide the following to the purchase : Itemnumber: 8868 Plant Cover 12mx16m The photos show an almost identical system. for more information please contact us. please keep the item number ready Shipping costs pls contact us; Second Hand

WASHING INSTALLATION 90° One washer to washing system to clean the containers. The containers are tilted 90 degrees and transported through a washing device. The washing device consists of a housing that contains a spray device which is suitable for cold water with a pressure of 5bar. A conveyor belt to transport the containers. After washing, the containers are tilted back to horizontal position. No recycling water included. The concrete floor must be prepared to drain the water to a certain drain pit. The best option is lower the concrete floor in the area of the washer. OVERHEAD DE/STACKER For the PLC controlled movement, stacking and destacking of empty, containers with a maximum weight of 100 kg an overhead stacker/destacker is installed. The stacker/destacker can PLC controlled take up from:
-a-        The destacking position on the buffer (this is also the  ...

750 MW each, UNUSED Gas Based Complete Combined Cycle Power Plants 2 units available Technical Specifications: The Project Details: 1. EACH module has two Gas turbines GE 9FA.03 (DLN2+) and one Steam turbine GE D11. Each GT exhaust is directed to the triple pressure unfired, natural circulation horizontal, type CMI USA HRSG. This configuration helps turndown operation of station up to 45%. 2. The Station is based on robust design of GE Gas Turbine with high efficiency DLN2+ Dry low Nox system, each GT is site rated for an output of 235 MW and the triple pressure reheat GE D11 Steam Turbine with downstream Exhaust, is site rated at 266 MW. The HRSG is a Triple pressure, Natural circulation, Horizontal design type with Deaerator atop the LP drum. Thus Net Combined cycle efficiency at Site condition is approx 57% on LHV basis. The inherent design of the gas turbine reduced the N ...

7.2MW diesel power plant. This vintage power plant has been used as an emergency generating sets for a larger R&D center in Korea, a very short actual running hours (abt. 2000~3000hrs) and has been well maintained, so our company can confidently recommend this power plant to anyone who needs it. The plant was dismantled and has been now stored in our factory and will be delivered to the buyer after the performance verification test of the generating sets at our test shop. Main Specifications - Engine Model: SSANGYONG-MAN 18V28/32H x 2 Sets - Manufactured & Running Hours: in 1999 & abt. 2000~3000hrs - Continuous Output: 3600kW x 720 rpm - Frequency & Voltage: 60Hz & 6600V - Fuel Oil: Diesel Oil / Heavy Fuel Oil - Plant Auxiliary Equipment: 1 set

l 45 kw POWER 680 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 45 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw

WARTSILA COGENERATION PLANT YEAR: 2007 POWER OUTPUT: 1.50 MW

Qty. 1 Second-hand bar and wire rod production plant Mfc.: Sarralle, Danieli, ABB, Indar Built: 1990’s, 2000, 2005, 2007, 2010 Revamped: 2008 Capacity: 1,100,000 T/annum Entry material: Scrape Semi product: Billets Size: 130x130 mm or 140x140 mm Length: 8 – 13 m Reinforced Bars: Dia.: 8 - 40 mm Length: 6 – 12 m Rebars: Dia.: 8 - 16 mm ID: 850 mm OD: 1100 – 1250 mm Height: 800 mm Wire Rod: Dia.: 5.5 – 14 mm Scope of supply: Scrap Transportation Machines EAF Ladles Furnace Continuous Caster Billet Reheating Furnace 23 Rolling Mills (Dia. 8-10 mm) 21 Rolling Mills (Dia. 12-32 mm) Wire Rod Mill Flying Shears (2) Spooler Line Cooling beds (2) Cranes Transformes Spare Parts

Qty. 1 Second-hand aluminium foil rolling mill plant Mfc.: Sambhav Built: 1993 - 2012 Revamped: 2015 Foil width: 1000 mm Entry thickness: 8 mm Exit: 8 microns Consist of: Melting furnace 22 MT Holding furnace 15 MT Strip caster Roughing rolling mill Intermediate foil mill Finishing foil mill Heavy slitter Strip slitter Foil separator Qty. 2 Foil slitters Annealing furnace

Qty. 1 Second-hand strip rolling mill plant Mfc.: Gautchi, Pechiney, Spidem, Stein Heurty SA, TECMO-HUNTER, ACHARD, WALDRICH Built: 1971, 1973, 1975 Modernisation in 1991 Strip width: 850 – 1600 mm Thickness Entry: 12 mm Exit: 0.3 mm Consist of: Qty. 2 Strip casting line 4-Hi rolling mill Qty. 2 Homogenisation furnaces Slitter Grinder Qty. 2 Coil cars

Concentrate plant 6000 l /h 3 stage system with plate heat exchanger For malt extract and apple juice concentrate

Loading / loading for boilers or similar in a very good used and functional condition. Custom order / manufacturer unknown. Completely made of stainless steel, rollable, including basket, basket size B/D/H 105/85/70 cm. Dimensions W/D/H 170/100/250 cm. Workshop tested, ready for use. More on request.

Pos.1 Buffer conveyor belts for layer formation for 4 frieze lengths Pos.2 Gantry stacking system Pos.3 Parcel roller conveyors in the area of gantry systems Pos.4 Security technology Pos.5 Machine control Pos.6 Intermediate strip automatic The mechanization is designed for the following workpiece dimensions: Length: 320 - 1000 mm Width: 56 - 120 mm Thickness: 20 - 40 mm Stack Dimensions: Length: 400 - 1000 mm (double lengths up to 2 x 520mm) Width up to: 1200 mm Height up to: 1200 mm Stacking is carried out on Euro pallets Max. output: max 40 parts/min or max 4 layers/min (board or batten layer!) Pos.1 Buffer conveyor belts for layer formation for 4 frieze lengths Quantity: 4 pieces Length: 2600 mm each Usable width: 800 mm each Propulsion: Spur gear motor Conveying speed: 15 m/min Incl. side guide rulers and layer alignment (One layer is formed,  ...

Vacuum Packers Dillmann Machine Systems DMV 400 DMS Specifications: 230 Volt / 50 Hz / 4 A Year of construction 2008 Weight: 40 kg Chamber size: D420 x W455 x H110 mm Welding bar length: 430 mm max. bag size: 390 x 450 mm Machine design Completely stainless steel Compact, solid design Surface sanded domed acrylic glass lid 2 inserts for different height levels in the chamber High-performance pump with 16 m³ capacity Ease of use Vacuum-adjustable Welding time adjustable Stock machine, immediately available! Function checked condition see original pictures. 03423-706493

Qty. 1 Second-hand pulp moulding plant Maker: DongJin MP Tech Model no.: DPF 70-85 S2 Built: 2007 Dry type pulp moulding machine Quantity: 4 units Condition: can be inspected in dry running Three step way: heating /pressing/vacuum dry -Platen size: 700 x 850 mm -Dimensions: 1300(W) x 3200 (L) x 4000(H) mm

Fettbackstation / Berliner Backstation consisting of 4 fat pans 1x Donut Filler 1x large exhaust hood incl. fire extinguishing function

Plant complete with all the machinery and molds to produce plastic pots, saucers, cages and thermoformed pot holders of various types and sizes: from 40 cm. up to 1 m. Composed of: N1) 135 ton SANDRETTO plastic injection press N1) 135 ton SANDRETTO plastic injection press N1) 200 ton SANDRETTO plastic injection press N1) 300 ton SANDRETTO plastic injection press N1) 400 ton SANDRETTO plastic injection press N1) 5 pallets CAMPETELLA robot + labeller N1) 7 pallets CAMPETELLA robot + labeller N3) automatic stacking and coding lines N2) mold cabinets with drawers with a capacity of 1000 kg N1) refrigerator to cool water N1) freecooler to cool the oil N59) molds for flower pots

82MW ISO rated combined cycle power plant. The plant’s main equipment is composed of a Rolls Royce Trent 60 DLE Gas Turbine (also known as the SGT-A65), a Nooter/Eriksen HRSG, and a Siemens SST-300 Steam Turbine. These are below; 1. Rolls Royce USA, manufactured Trent 60 (SGT-A65) Gas Turbine Generator Set; · Manufactured in 2016, delivered in August 2017. Never used. · 65.9 MW(e) ISO · 43.8% Gross efficiency / 8,228 kJ/kWh Heat Rate · DLE Dry Low Emissions with ≤ 25 ppmvd at 15% O2 on fuel gas · Cold start to full power in under 10minutes · 50Hz, but easily convertible to 60Hz · Engine still preserved in original shipping container · An aero derivative gas turbine 2. HRSG is licensed by Nooter Eriksen USA; 3. Siemens Steam Turbine Generator SST-300 C2S/C160; · Manufactured in 2016 · Output 15.75MW ISO · Speed 7059 RPM · Admi ...

Used line for big-bag unloading, mixing, screening and packing powders into bags The line includes: 1. Station for emptying large-capacity bags. As a stand-alone device, it is used to empty large-capacity bags in a bagging line. The station consists of a stable supporting frame with a discharge hopper with an iris closure, a tip and an emptying screw feeder. The upper structure with a large-capacity bag suspended on a removable suspended cross will be placed on the lower frame using a high-lift truck. The cross on the upper structure is fitted with a sliding fit - on four gas supports, which ensure gradual lifting of the large-capacity bag during emptying, which ensures complete emptying of the bag. 2. Mixer 3. Conveyor system 4. Screener 5. TPL 50 strain gauge bagging line for filling open bags Main elements of the line: - Scale pre-tank with supporting structure and  ...

36,000 m3 thermal oil supply system/exhaust air purification plant (special plant construction) WK, Year of construction: 2012, with heat recovery and cooling supply, The system is currently designed for two printing systems. Depending on the Machine equipment for 3 - 4 printing systems. The system consists of the following components: - 1 roof-mounted thermal post-combustion system / exhaust air purification WK Thermal Engineering Plant, boiler and apparatus construction WKTNV, year of construction: 2012, exhaust air volume at the inlet 36,000 m³/h, maximum permissible combustion chamber temperature max. 730 °C, burner type WK/H1 gas cone, Burner power 6,600 kW, fan power 200 kW, maximum permissible inlet temperature 210 °C, Maximum permissible solvent throughput 500 kg/h, natural gas heating medium, calorific value of the heating medium 32693 kJ/m³, max. heating fuel con ...

Powder coating system for large parts Example:(all sizes can be changed individually) Space requirement: 30 x 15 meters Part size: L= 6,200mm W= 2,300mm H= 2,000mm Cleaning booth walk-in incl. spray wreath automatic 1 Dimensions of the cabin Length 9,000 mm Width 4,500 mm Height 3,400 mm 2 Mass of tanks Length 1,200 mm Width 850 mm Height 1,000 mm 2 Dimensions of the cabin complete Length 9,140 mm including tanks width 5,580 mm Height 4,200 mm Coating booth walk-in, manual coating Lmmuapd8S 1 Dimensions cabin length 9,000 mm Width 4,500 mm Height 3,400 mm 2 Dimensions of the cabin including extraction Length 10,125 mm Width 4,500 mm Height 3,400 mm Powder curing furnace 1 Inner dimension length 6,500 mm 2 Inner dimensions width 2,500 mm 3 Internal dimensions height 2,950 mm 4 Outer dimensions incl. thermoblock length 7,600 mm 5 Outer dimensions incl. ...

1. Powder curing furnace 1,500 x 1,200 x 1,750 mm 2. Powder Coating Booth -KG DUO-01 3. Wagner powder coating plant, – Prima Sprint – 1. Powder curing furnace 1,500 x 1,200 x 1,750 mm 1 Inner dimension length 1,500 mm 2 Inner dimensions width 1,200 mm 3 Internal dimensions height 1,750 mm 4 Outer dimensions incl. thermoblock length 2,250 mm 5 Outer dimensions incl. thermoblock width 1,815 mm 6 External dimensions incl. thermoblock height 2,006 mm, 2,296 mm incl. exhaust pipe 7 Substructure 1 set of steel profile 8 walls 1 set of galvanized sheets 1mm on both sides, RAL on the outside 9 insulation walls, ceiling 1 set of rock wool 150 mm, floor is insulated with 50 mm 10 Floor Furnace Gets 2 Entry Rails for Tray Wagons 11 Temperature 220°C 12 fans 1 pc. 2,600 m³/h 13 electric motors 1 pc 1.1 kW , 1450 rpm, 3 F, 50 Hz 14 Thermal power 14 kW 15 hinged doors, single ...

220 MW SGT-600 GT Complete Power Plant Duel Fuel Gas Turbine Power Plant Gensets 220.5 Megawatts in total 6 units available, 24.5 Mw each Speed 1,500 rpm, Generator Output 11 kV, Frequency 50 Hz Average running hours 70.000 hours Gas Turbine Power Plant operated predominately on natural gas with standby diesel fuel. Can be converted to alternative fuels as heavy fuel oil . Depends on the demand and needs of the customer. Phase I (5 units, commissioned on 2007) Phase II (4 units commissioned on 2012) Routine preventive maintenance was done for all units under OEM supervision, Emission ISO Standard at 15% O₂ Original Dry Low NOX ( DLE ) Combustion Chambers Inertial Filtration and Single Stage F9

J Kugler filling line, that has been dismantled about half a year ago from the production it has been running in. The machine is now dismantled and in our warehouse safely storaged. With this you get a complete filling line with a filling machine, a lid applicator, a capper and a label machine. The filling line has been running at Novartis in their German department, so all the machines are very well kept and serviced. Novartis have been running 1000 ml products with a lid”, a cap on the top and a label on the side. They have been running 20 products per minute = 1.200 products per hour. The filling line is from 1990 and has been running at Novartis from when it was new. The filling line is complete with a rotary infeed table, 1 headed piston filler with lotion lube pump, lid applicator, cap applicator, label machine and an End of Line Production Systech Display Monitor” to co ...

Wood flooring line consisting of: Motorized loading roller conveyor Suction cup loader Squaring / panel saw Multi-blade panel saw Tipper dry or glue interlocking slats Stacking machines Packaging machines Parcel loader Packaging Automatic strapping machine for pallet unloading camera-driven movements The loading roller conveyor, the stack (max 50 sheets, 8mm thick) is transported under the suction cup loader, where the panels are picked up and positioned on the hopper of the panel saw. Model:TSA 360A The sectioned sheets go on a 90° translator and are transported by belts over a suction cup introducer.

Bread plant W&P Parta U CR59 The system consists of 4 machines 1x W&P Parta U dough divider 1x W&P Intermediate fermentation chamber 296 baskets 215x360cm and height 282cm 1x W&P CR59 Cone wiper 1x W&P long scooter

6,000 l / h product 3 Stage system, with plate heat exchanger and heat recovery Control S7

CONTAINER ANLAGE 90 m2 plant, 6x 20 FT OfficeContainer Building / Office / Living Room, residential container workshop container container plant BJ 2005 - 6x 20 foot container (2.47 m wide, 6.00 m long, 2.90 m high) exterior size - 2.50 m high inner dimension - Residential container office container construction site container, container plant - complete price 6 pieces, excluding assembly - easy assembly - Construction Year 2005

used Benier brotteig precursor with adjustable wits completely in stainless steel.The machine is immediately available in the warehouse in Bielefeld.Further used bakery machines please see the catalogue on the right we have more than 700 machines in stock in Stock. Built in 2002 400V / 50 Hz Stainless steel cladding with 2 blowers Scrapers are adjustable checked and cleaned Condition "good" Dimensions: Height: 150 cm Width: 220 cm Depth: 110 cm

For sale is a workshop-overhauled and function-tested, free-standing VA diatomaceous earth dosing device. The device is immediately ready for use. Specifications: Manufacturer: Schenk Year of manufacture: unknown Type: DO-S-250 Boiler capacity: approx. 250 l (with lid almost 1/2 hinged with hinge) Hourly output for KG filtration: 200 hl for beer, wine and fruit juice Dimensions total: L max. = 1.20 m / W max = 0.80 m / H max. = 1.685 m Beer pipe: Input/outlet DN 50 KM/G - Dosing connection in the beer pipe DN 25 KM Connections in the boiler: 1 inlet at the top side DN 50 G with 90-degree bend (inside) downwards 1 remaining outlet DN 50 G with shaft closure and handle from above 1 connection DN 32 KM above 1 DN 50 KM connection at the bottom side with a 90 degree bend upwards - then reduced from DN 50 to DN 10 G Boiler dimensions: Diam. inside = 0.65 m ...

-for long rolling of breads -without nameplate -in baker's condition -Photos before cleaning

R&E Conveyor No 2618 Y.O.M. 1998 Width 2x 650 Length 16 m Curved, head approx. 6 m Good condition!

Bread-long wrapper W&P BM 51 B -with blue plastic straps -mobile on wheels -for bakery baking industry

- 5 aluminium silos with attachment filter incl. discharge screw with slide made of V2A - 4 aluminium silos for manual filling with discharge screws - 3 dosing scales - Optional with dust filter

Hyundai Steel Dangjin Facility (widely known as "Thin Plate Mill") is a premier steel production plant featuring a Compact Strip Process (CSP) as the main production line, complemented by a 150-tonne heat-size electric Meltshop, a thick Slab Caster, and two Skin Pass Mills. Initially commissioned by Hanbo Steel in 1995, this facility was acquired by Hyundai Steel in 2004 including a major modernization in 2011 and more recent upgrades, ensuring its continued excellence in production. Assets Available for Sale: • Electric Meltshop 150 tonnes heat size – DC EBT Electric Arc Furnace, Ladle Furnace, Vacuum Degasser and associated equipment. • CSP – A Thin Slab Cast & Rolling line combining casting, heating, and rolling. 55mm thickness slabs directly enter a tunnel furnace and are rolled in a Hot Strip Mill for final strip thickness from 1.4 to 16mm and up to 1,560mm width ...

Resin production plant. Capapcity 1200 tons per month. Plant can produce acrylic resins, alahide resins, poliuerethane resins on  buthyl octate base, acetone base, and xylane base. Plant can produce 55-60% resin concentrate wchich acan later be diluted in another factory. Plant has 3 main pressure reactors each 10 ton of batch. Plant has a storage tanks 160000 L tanks. Plant is build in Atex execution. More information available upon request. Advise on resin production technology, recepies and technological advise is possible on separate agreement and price. Below you can find a photo gallery of the factory, more information please call.

Pressure Bottle Filler. 24 fillers. System FALSCH FLASCHEN. Whole machine made in inox. Machine after total renovation in 2019. Warranty: 24 months.

Y.O.M.: 1989 Temperature Homogenizer speed-controlled Agitator right-left speed-controlled very good condition Dimensions LWH: 900 x 500 x 1450 mm Control cabinet: 800 x 300 x 1550 mm Weight: approx. 500 kg

Availability: immediately Hours: 0 Cup-Cake dosing line suitable for the production of round CUP-CAKES Ø 45 - 90 mm and small cakes (muffins, Magdalenas, Cake-Donuts, Mini-Cake Donuts, cake bars etc.) arranged on trays measuring 400x600 mm, with 6 x 9 wells. DESCRIPTION OF THE MACHINE: PART 1 No. 1 conveyor belt with plate chains, which is positioned at the entrance of the dosing line and serves as a buffer for about 4 sheets, with the following characteristics: ● Infinitely variable movement by means of a motor with frequency converter. ● Usable width: 600 mm. ● Length: 1500 mm. ● Mounted on wheels. PART 2 No. 1 Intermittent chain conveyor with slides, with the following features: ● Adjustable guide walls. ● Drive with a motor with frequency converter. ● Intermittent movement, electromechanically controlled, with programmable conveying step. ● Acceler ...

Y.O.M.: 1980 No.: 10027 Usable volume: 150 l Pressure double jacket: +1 bar Vacuum pump Pressure gauge, temp gauge Scraper agitator, three-way valve 3 intake ducts Lid to be opened via lifting pull Dimensions LWH: 1700 x 1000 x 2100 mm Weight: approx. 500 kg Products: e.g. mayonnaise, sauces, ketchup, cosmetics, creams etc.

Dairy Mschinery UK now offers new Glass Bottle Fillers for Milk and Juice. We offer machines for Hot fill and Cold Fill. Our bottle capacities are between 1000 - 7000 bottles per hour. Manufacture : Dairy Machinery UK Volume : 500ml - 1000ml Capacity : Option on order between 1000- 7000 bph Capping : 38mm magnetic capping chucks Filling Nozzles : Gravity Filling on Rubbers Lift and Fill or Gravity Filling Drop and Fill Cap : Aluminium Screw Cap CIP : Available Controls : Control panel Standards 2019 Certified : EC certificates Installation : We install all our machines at the clients facilities. Warranty : 12 months Spare Parts : spares@dairymachineryuk.co.uk

Y.O.M.: 1991 No.: 4745 2 hoppers, 1x with double jacket Scraper agitator speed-controlled Homogenizer speed-controlled Double jacket pressure-resistant Temperature controller, vacuum Condition: very good Dimensions LWH: 1100 x 600 x 950 mm Weight: approx. 300 kg

Y.O.M.: 1999 No.: 900/1 Scraper and Homo speed-controlled Vertical stroke, double jacket, swivel Temperature gauge, Vacuum, Ystral-Turrax Temperature control device GWK Type teco CS 90 Y.O.M.: 2002 Heating capacity: 9 kW Cooling capacity 23 kW, temperature maximum 95°C Dimensions LWH: 1200 x 800 x 1000 mm Weight: approx. 100 kg

Fat baking device Berlinerbackstation Esback -Built in 2009

Conveyor belt / climbing belt (inchGiraffeinch), built in 2013, in a very good used and functional condition. All metal parts made of stainless steel. Plastic conveyor belt, 45 cm wide, with takers. Rise height 210 cm. Machine is rollable. Speed infinitely adjustable. Connection values 400 volts, 0.55 kW. Workshop-tested, ready for immediate use. More on request.

Scraper and homogenizer (Ystral) speed-controlled Vertical stroke, double jacket swiveling with heating and vacuum pump on a mobile cart switchgear, timers, etc. Condition very good Dimensions LWH: 700 x 600 x 1900 mm Weight: approx. 150 kg

A steam-powered freeze drying plant HOF with 1.8 m2 usable space. With stainless steel chamber door, ice capacitor, set of actuators (6 pcs.) sep. Panel.

Material: PE, PP, PS // DC motor: 132 kW, power: approx. 300 - 500 KG/hr, screw 90mm, L/D30, strand nozzle, water bath, strand granulator.

Specifications: Support surface table: Width x Depth x Max. Clamping Distance: 192 x 115 x 120 mm Height center cutting wheel above table: 520 mm Cutting disc height adjustment via Cylinder with measuring system: 445 mm Cutting Wheel Dimensions: Min.: 350 x 2.8 x 32 mm Max.: 400 x 4.0 x 32 mm Workpiece dimensions max. length: Workpiece feeder: 3500 mm Workpiece discharge: 2000 mm Workpiece dimensions min. length: Workpiece feeder: 300 mm Workpiece discharge: 300 mm Workpiece feeder: Servo - controlled Measuring distance via measuring system: 3500 mm Circumferential speed: 25 - 60 m/sec Main motor: 10 kW Dimensions of separation system (WxDxH), approx.: 850 x 1600 x 2815 mm Weight: Machine: 980 kg Workpiece feeder: 380 kg Workpiece discharge: 350 kg Control cabinet: 280 kg

Compounding system with underwater granulation. Material: PE, PP, PS, ABS (+ fillers) // Details: DC motor, DC rotor, segmented screws (2x x 70 mm / 40D) and cylinders, degassing, vacuum pump, stuffing unit, backwash screen changer GNEUSS RSF 150, underwater granulation GALA with cutting rotor, water circulation system, heat exchanger, centrifugal dryer. Controls: SIEMENS S7 with screen visualization. Available at an additional cost: Sidefeeder, 4-fold gravimetric dosing system. (Ref. No. G27615.2)