mikron ag used for sale

Emergency power system with 5 x containers each 1250 kVA Engine Type: Cummins QSK45 Year of construction: 2004, general overhaul 2017 Operating hours after general overhaul: approx. 3000 Power each: 1250 kVA Cooling: Water with radiator Speed: 1500 1/min Tank: approx. 1430 liters Generator: Stamford HC734F Voltage: 400/231 V, 50 Hz Control Panel: DEIF Control, AGC4, Circuit Breaker Type: Container Weight: approx. 20 tons Optional 1x NSHV Container Was used as a rental system and emergency power system. Parallel operation, synchronization and load management. Subject to prior sale - errors possible! Internal Reference Number: E-1004-72

This is a Stainless Steel Double Jacket 250liter Vacuum Reactor system used in pharmaceutical or other applications. It is equipped with a vacuum pump able to reach -15psi and heating through oil or water bath. Inside it has a good overhead agitator and an additional bottom stirring system which will not allow any material lay down and stand still. The bottom stirrer is missing its motor but it has ready for connection the cobbler where the motor would fit onto and should be adjusted according the RPM stirring needs of the application. Unit Specifications: - Vacuum Pump with 1hp AEG single phase motor with -15psi (checked to be in working condition) - Agitator Motor with manual RPM regulator (checked to be in working condition) - Double Jacket Oil Heating System with 3 X 6kw resistances (cheched to be in working condition). Total heating 18kw - Capacity 250liter - Stainless Stee ...

Stainless steel steam reactor with agitator capacity 3,000 lts Description Process reactor of 3,000 liters made of stainless steel. It has: agitation with propeller, four baffles, klopper bottoms, manhole on top, tubular coil throughout the container, product inlets on the top, outlet on the bottom bottom and four support legs. Motor power: 5 kw. Test pressure: 10.6 bar. Features Year: 2001 Width: 1800 mm Height: 4600 mm

Autostainer Link AS48 Agilent Dako https://www.agilent/en/product/autostainer-link-solution-for-ihc/autos tainer-link-48/autostainer-link-48-75845 - Process 48 slides in less than three hours. This means you can finish 96 slides in a normal working day with just one Autostainer Link 48 and one PT Link. - Gain up to 45 minutes of autonomy compared with our fastest Autostainer Plus - Make the most of your laboratory time by processing slides in parallel using PT Link and the fastest Autostainer Link 48 ever. - Have the freedom to set your own standards and the ability to control them VERY GOOD CONDITION Date of purchase: March 2014 Under annual maintenance contract PT Link DAKO tissue pre-treatment module https://www.agilent/en/product/pt-link-for-pre-treatment/pt-link-acces sories VERY GOOD CONDITION Date of purchase: March 2014

Plastic agglomerator, engine: 75 KW (100 hp), tank size: 1 m high, 1 m diam. Electrical panel. Ready to get started? Contact us directly! Send us a WhatsApp message to (+34) 647 590 257 or an email to infogester.es for personalized advice.

Container YOC 2003 Hours : 400 Pictures on request ! Mail : motorent-online

Description: Electric Motor 1.1 kW, Hydro Aggregate weight approx.: 150 kg, Approx. Onsite Dimension. (l x w x h): 1,200 x 800 x 500 mm

Tank agitator with propeller - green More then 300 machines new and second hand on our seema .de

13,000 LITRE RIEGER MASH AGITATOR TANK WITH PADDLE AGITATOR/AGITATOR AGITATOR WITH LATERAL FLOW INTERRUPTER ON THE CYLINDER WALL, VERTICAL, V2A https://eurolux.de/product/24-0502euba-13000-liter-rieger-maische-ruhr werktank-mit-paddelruhrwerkagitatorruhrwerk-mit-seitlichem-stromungsun terbrecher-an-der-zylinderwand-stehend-v2a KK UNI-RILL Specifications Surface inside 2B=IIIC sanded Weight 3000 kg Manufacturer: RIEGER Surface marbled on the outside Volume 13000 L Material V2A (AISI 304) 1.4301 Total height 4900 mm Cylinder height 2150 mm Diameter 2500 mm Agitator paddle stirrer Vertical design Number of feet 4 on frame Last Use Food Technical Documentation Yes Surface: Inside 2B=IIIC Marbled on the outside Tank top: Klöpperboden 4 crane eyelets Threaded socket DN50 Gearbox and engine BAUER Filling flange DN100 Dom Ø420 front Cyl ...

D.C. Norris & Co cooking vessel with agitator, model: JONI150, serial number: 2594, year of construction: 06-11, 400 V, 3 PH, 50 Hz, 50 A, 32.2 kW, volume: 150 liter, dimensions: 1350 mm x 1000 mm x 1250 mm.

Key data: 160 KW, 200 kVA, 400 V

Diesel Emergency Generator Type PDH16N with generator 6S160PN 200 kVA, 160 kW, 400V/3Ph/50Hz Built in 1971, only 772 hours run, mainly used in a hospital as an emergency generator

S/s tiltable double jacked tank with agitator, volume: 350 liter, dimensions: 1500 mm x 960 mm x 1900

EWAC double jacked s/s tank with agitator, volume: 316 liter, dimensions: 1300 mm x 1400 mm x 3800 mm.

EWAC double jacked s/s tank with agitator, volume: 316 liter, dimensions: 1300 mm x 1400 mm x 3800 mm.

Industrias AJA double jacked s/s tank with agitator, volume: 400 liter, dimensions: Ø 800 mm x 2200 mm.

Emergency generator Bruno, 150 kVA, 400 Volt, YOC 2011, Genrator Leeroy Sommer LSA 442M95, engine John Deere CD6068

Description: serial number AA1/014869 min. piece length mm 230 max. piece length mm 3100 min. piece thickness mm 3 max. piece thickness mm 100 working height from the floor mm 920 movable beam positioning speed m/min 2 feed speed of chain tracks m/min 4-24 Betriebsspannung 400 V, 3 phases, 50 Hz nennstrom 163 A leistung 10 kA for futher technical detail please consult document PDF Concept NT.mod.pdf Approx. Onsite Dimension. (l x w x h): 5,000 x 4,000 x 2,000 mm, weight approx.: 6,800 kg

Manufacturer : Comber Model: Pharmadry PH 100 Year : 1988 Type : vacuum dryer   Maximum temperature: 99?C Material: 304 and 316 stainless steel (in contact with product). Classification: Atex EEx IIB T4   Main tank diameter : ? 500 mm Main tank depth: 700 mm Power: 4 HP Filter Pressurised receiver tank Tubular heat exchanger   Gaskets: new Paint: new Mechanical seal: As is, good condition

Power 262 KW, Displacement 8419 ccm, Diesel,

Power 130 KW, displacement 7365 ccm, diesel, abs. Running hours 2400 hrs

Power 188 KW, displacement 8419 ccm, Diesel, NOTE: The attached pictures of this position are for documentation purposes only, the real pictures of the position will be created and attached in due course

Power 216 KW, displacement 8419 ccm, Diesel, abgel. Running hours 7433 hrs

Power 90 KW, displacement 4397 ccm, Diesel, NOTE: The attached pictures of this position are for documentation purposes only, the real pictures of the position will be created and attached in due course

Description: HSK63 LOCK CASE D=16 MM 2 SPINDLES Approx. Onsite Dimension. (l x w x h): 800 x 500 x 500 mm, weight approx.: 10 kg

Description: Max. rotational speed 5000 rpm Serial number 4-21978 without further accessories Approx. Onsite Dimension. (l x w x h): 300 x 300 x 300 mm, weight approx.: 8 kg

Description: max. drive speed 10000 rpm max. output speed 15000 rpm max. torque 20 Nm Permissible operating temperature 85° C without further accessories Approx. Onsite Dimension. (l x w x h): 150 x 100 x 250 mm, weight approx.: 6 kg

Spinner for Agfa Avantra 44S ,20,000 RPM, refurbihed 2013, with warranty. We have all Spareparts for Agfa Avantra 25/30/44, AccuSet.. on stock. Don't hasitate to contact us.

Spinner for Agfa Avantra 30 ,30,000 RPM, refrushed 2012, with waranty. We have all Spareparts for Agfa Avantra 25/30/44, AccuSet.. on stock. Don't hasitate to contact us. Available: Yes

Spinner for Agfa Avantra 25,20,000 RPM, refrushed 2011, with waranty. We have all Spareparts for Agfa Avantra 25/30/44, AccuSet.. on stock. Don't hasitate to contact us. Available: Yes

Agfa Aphis Board for new PCI. We have all Spareparts for Agfa Avantra 25/30/44, AccuSet.. on stock. Don't hasitate to contact us. Still in operation: No Available: Yes

Agfa Aphis Board for new PCI. We have all Spareparts for Agfa Avantra 25/30/44, AccuSet.. on stock. Don`t hasitate to contact us. Still in operation: No Available: Ja

Spinner für Agfa Avantra 30 ,30.000 RPM, refrushed 2012, with waranty. We have all Spareparts for Agfa Avantra 25/30/44, AccuSet.. on stock. Don`t hasitate to contact us. Available: Ja

Spinner für Agfa Avantra 30 ,30.000 RPM, refrushed 2012, with waranty. We have all Spareparts for Agfa Avantra 25/30/44, AccuSet.. on stock. Don`t hasitate to contact us. Available: Ja

<br>Spinner for Agfa Avantra 44s, 20,000 RPM, refurbihed 2013, with warranty. We have all spareparts for Agfa Avantra 25/30/44, AccuSet... on stock. Don't hasitate to contact US.<br><br><br>

CNC EDM machine Fabr. AGIE type Agietron 200 CSeries 03, device 04, list of devices 356804.5 built in 1987Travel X: 500 mmTravel Y: 350 mmTravel distance Z: 500 mmSupport surface: 800 x 630 mmMax. Workpiece dimensions: 1000 x 700 x 320 mmInner container dimensions: 1070 x 740 x 420 mmWorkpiece weight approx. 1200 kgMax. Weight of the electrode: 400 kgDistance table - quill: 180/680 mmPosition deviation (PA): 0.005 mmaverage position spread (PS): 0.003 mmmean inverse span (u): 0.002 mmResolution: 0.001 mmNumber of flushing connections: 10manual flushing: 1/20 l / minautomatic dosing spray: 8 / 3-800 ml / minControl mode: Multi-taskingSimultaneously controllable axis: 4Simultaneously controllable rotative and linear axes: C with X, Y, ZStorage Capacity: 3.5 , MS-DOS, 720KBScreen: color 14 Interface: RS 232 / CV 24Rated current: 60 ARemoval rate: 450/590 mm3 / minNumber of channels: 1Agiepu ...

CNC spark erosion machine make AGIE type AGIETRON 100Device list 357914.1, series 015, device 005Technical specifications:Table size: 580 x 450 mmwith 3 T-slots 10 mmX axis: 350 mmY axis: 250 mmWeight of the erosion machine: 2275 kgWith- Agiematic T control, device list 813834.9, series 008, device 008, 290 kg 1.25 kVA- FSK, device list 813864.6, series 008, device 009, 65 kg- ATK 35, device list 144170.8, series 016, device 009, 220 kg- Generator Agiepuls 60M, device list 814104.6, series 008, device 008, 305 kg 3.4 kVA- Dielectric unit DA 100, device list 369964.2, series 020, device 009, 460 kg, 4.2 kVA + PD + GEN- tool changer- Cooling unit make HIROSS ICE 005, 230/1/50 serial no. 3293540001, 110 kgused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We  ...

x-travel: 350 mm y-travel: 250 mm z-travel: 256 mm max. size of workpiece: 750 x 550 x 250 mm U-axis: +/- 70 mm V-axis: +/- 70 mm rapid traverse X/Y/Z axis: 1,5 / 1,5 / 0,6 m/min rapid traverse U/V-axis: 0,6 m/min max. concentricity: 30° / 100 mm control: AGIEVISION wire dia.: 0,1 - 0,33 mm speed of wire: 60 - 300 mm/sec wire retraction: halbautomatisch total power requirement: 9,1 kVA weight of the machine ca.: 3,6 t dimensions: 2,21 x 2,21 x 2,22 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 500 mm table width: 350 mm ampere: 65 A Control: AGIEVISION 5 CNC total power requirement: 20 kW weight of the machine ca.: 4000 kg dimensions of the machine ca.: m A G I E (Switzerland) CNC - Controlled Wire Cutting EDM Machine Model AGIECUT PROGRESS V 3, Year 2007 Working range, X Y Z (=height) 500 x 350 x 426 mm Wire head, U-V axis (helical/taper cuts) + / - 30 °/ +/- 70 mm Resolution of axes 0.0001 mm Speed for positioning the axes up to 3 m/Min. Tolerances (If machine is new) 4 µ Workpiece dimensions, L x W x H max. 1.050 x 650 x 420 mm Max.weight of workpiece with/w.o. Dieelektricum 400/800 kg Clamping System Universal Beams with fixing holes Cutting wire Ø 0.2 – 0.33 mm Size of wire roll up to 25 kg Cutting speed of wire  ...

Spark Erosion Machine AGIE AGIETRON 250C used machine in excellent condition tool change 24 positions

Wire erosion machine make AGIE type Agiecut AC 100Machine -No: 117 built in 1988Working area X: 300 mmWorking area Y: 200 mmWorking area Z: 250 mmTable length: 510 mmTable width: 580 mmWorkpiece dimensions: 810 x 580 x 250 mmWorkpiece weight max.: 200 kgWire diameter: 0.03 - 0.3 mmTotal power requirement: 10 kWWeight approx: 3.0 tonsWith- Agiepuls MM- Operating hours 33976 hrs.used, in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

AGIE AGIECUT EXCELLENCE 2 wire EDM machine built in 1999 in Switzerland, is used in the production of e.g. precision dies, tools and punches. For the machining of workpieces, the machine uses advanced electrical erosion technology which makes it possible to achieve difficult shapes in even the hardest materials. The use of this method further minimises or completely eliminates the need for other secondary processes, such as polishing. The AGIE EDM machine is equipped with a state-of-the-art AGIEVISION CNC controller and brushless axis servo motors to guarantee the highest machining accuracy and precision in the shortest possible time, with low energy consumption at the same time. The machine also comes with among others an integrated generator, a semi-automatic wire threading system and the AGIESETUP 3D measuring probe for automatic detection of the plane and position of the workpiece ...

4 up Thermal CTP System AGFA Avento II S (Same as Screen 4300 S) year: 2008 32 diodes 102.000 plates produced with Singel Loder with Stacker with RIP Harlequin with few packages of offset plates In case you need chemical Processor we can offer separatly. Located German available now

Defected Power cable for down head

This AGIE AGIEMATIC + AGIEPULS 60 HSF erosion machine was made in the year 2000. It is equipped with an Agie control unit. The machine has a table of 600 x 450 mm.

This AGIE AGIETRON INTEGRAL 3 EDM Wire Cutting Machine was built in the year 1998. The machine has a table of 800 x 600 mm.

This Agie Agietron Integral 2 Erosion machine was manufactured in Switzerland in 1994. It operates for a max. workpiece weight of 400 kg and max. electrode weight of 100 kg.

Inv. Num. : 6319 Type: AGIETRON HYPERSPARK Producer: AGIE Created: 2006 Parameters: Control system: AGIEVISION Operating hours: 69006 h Switch-on hours: 31080 h Table dimensions: 600 x 450 mm Travel length of the X-axis: 350 mm Travel length of the Y-axis: 250 mm Travel length of the Z-axis: 350 mm Maximum table load: 400 kg Container size: 860 x 620 mm Equipment: Clamping solenoid 3x electrode holder Cooler Dielectric 8x dielectric filter Erowa clamping head

X-travel: 250mm, y-travel: 160mm, table dimensions: 420x250mm, max. workpiece height: 160mm, max. workpiece weight: 120kg, length: 1545mm, width: 1240mm, height: 1065mm, weight: 540kg, with documentation, the machine should be overhauled, an inspection is possible.

Axes X/Y/Z: 350mm/250mm/350mm, workpiece dimensions X/Y/Z: 650mm/580mm/250mm, max. workpiece weight: 100kg. Inner dimensions of work bowl: 860mm/620mm/360mm, rotation: 60rpm, capacity: 415l, filter quality: 3μm-5μm. Dimensions X/Y/Z: 2689mm/1855mm/2593mm, empty weight: approx. 3200kg, filling weight: approx. 4200kg, control: AgieVision. Documentation available.

travel -x axis: 800 mm travel -y axis: 500 mm workpiece sizes: 1.300 x 1000 U/min ampere: 60 A workpiece weight: 3.000 kg Control: CNC VISION 5 total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.