mi used for sale

Qty. 1 Second-hand aluminium foil rolling mill line Mfc.: Kyongil Machinery Built: 2003 Stopped: 2015 Type: 4-Hi Strip width: 850 mm Thickness Entry: 0.3 mm Exit: 12 microns Consist of: Foil rolling mill Foil separator Doubler Annealing furnace

Holy V-mix, Nautamix, Vrieco-, NAUTA mixer, cone mixing N.M. Holy b.v. V-mix 25,000 PLR New machine of the mixer is on your products (E.g., particle size, bulk density) and environment (E.g. ATEX zoning) adapted. -Capacity: 25,000 litres water filling -Usable volume: approx. 22,500 litres depending on the product properties -Container, lid, swing arm, mixing screw, spout housing made of V2A -Traverse normal steel, is covered but to the tank interior with a V2A plate. -All lubricants are H1 & halal approved and certified

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Manual nip adjustment, peripherally drilled rolls, Unidrive gearbox with flexible couplings, single 106kW DC variable speed motor. Very good condition.

Qty. 1 Second-hand aluminium foil rolling mill plant Mfc.: Sambhav Built: 1993 - 2012 Revamped: 2015 Foil width: 1000 mm Entry thickness: 8 mm Exit: 8 microns Consist of: Melting furnace 22 MT Holding furnace 15 MT Strip caster Roughing rolling mill Intermediate foil mill Finishing foil mill Heavy slitter Strip slitter Foil separator Qty. 2 Foil slitters Annealing furnace

Qty 1 x Schwabenthan 200mm dia x 450mm wide two roll mill, Manual nip adjustment, Digital nip gap readout, Electrically heated rolls, Jahnel gearbox with 10HP motor to each roll (variable speed), Variable friction ratio/roll speeds, Stainless steel interlocked guards and tray. Complete with electrical controls and in good condition. O/a dimensions 2700 x 1500mm

Qty 1 x Schwabenthan 150mm dia x 350mm wide two roll mill, Manual nip adjustment, Digital nip gap readout, Electrically heated rolls, Even/friction selectable gear ratios, Motor mounted under frame. Complete with electrical controls and in good condition. O/a dimensions 2400 x 850mm.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, FULL Unidrive gearbox with flexible coupling, 2 x 68kW DC variable speed motors. Variable friction ratio/roll speeds. In very good condition.

2 x tank mixer Capacity: 3120 l Dimensions: The height of the tank: 1550 mm Diameter: 1600 mm Total container height: 2650 mm

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, Unidrive gearbox with flexible couplings, single 138kW fixed speed motor. Fixed friction/roll speed. In very good condition.

QTY 1 x Berstorff 2100mm x 660mm dia two roll mill, Motorised nip adjustment, peripherally drilled rolls, FULL Unidrive gearbox with flexible couplings, 2 x DC variable speed motors. Variable friction ratio and roll speed. In very good condition.

Year of constr.: 2019 Dimensions: L 4400 mm x W 3500 mm x H 5000 m Ploughshare mixers: Type: PPP 2000 / 3 Manufacturer: MINOX Volume: 2000 Lt. Material: Stainless steel 3 x cutter heads Main drive: 37 KW;

MITSUBISHI MARINE PROPULSION ENGINE 735 kW 1450 RPM 2000 hours

we have all spare parts for the above engines Mitsubishi S6A3 , S12A2 S6R2 S12R S16R new and used Spare parts Cummins KTA all models,

MARINE GENERATOR SET Mitsubishi STAMFORD ALTERNATOR 295 KVA / 1500 RPM

Newmix Atmi life sciences Double jacketed paddle mixer Serial: 15883-005 2011, Stainless pharmaceutical mixer with 500L double jacketed mobile holding vessel, touch screen controls, Min - Max temp 0-90' degrees, jacket volume 6L, 1Ph

Various millstones

PVS 150 V Multicut with 15 to 22 KW with combinable cutting systems Rotor/ stator non-contact Hole disc with knife head or rotor/stator with perforated disc system 2 cutting stages

Bulk material system for mixing loose flours, powder, ganulate, spices and weighing into smaller batches Manufacturer Daxner GmbH Year of construction 2008 / plant in top condition / in stainless steel The system consists of the following components: 2x Nozzle Filter DFK-14/25/150 2x separation container Dm 1990 mm with vibration floor drain to rotary valve 2x rotary valve type Westinghouse AL 300 3C 2x eddy current screening machine type WM20 with magnetic box for metal separation and 2 sets of screen baskets 4x Horizontal Counterflow Mixer HGM-2000 2x Mixer inlet with folding box 2x Tube screw conveyor RSHN-250 2 x Tubular Auger RSHN-300 2 x Stafsjö Gate Valve (knife gate valve) 4x Transport Dosing Screw, Company Schenck Process GmbH, Type GRMD 42.089.089.0380.44.421.1119 If you want more information, please send us an email to: infobarsso and we will send you all  ...

x-travel 600 mm y-travel 500 mm z-travel 450 mm Control TNC 415 Heidenhain Main spindle: Speed range - milling 20 - 5,000 rpm Drive power - milling spindle 6 / 9 kW Tool holder SK 40 Quill stroke 90 mm Gear stages 4 swivel +/-90 ° Workbench: Bsi0Cso09Qu Table size 900 x 530 mm T-slots 7 T-slots - spacing 63 mm T-slots - width 14-H7 mm max. table load 400 kg Tool Changer: Number of tool positions 18 pos. Tool holder SK 40 max. tool diameter 85 mm max. tool diameter. with a free neighboring box. 150 mm max. tool length 300 mm max. tool weight 10 kg Tool change time max. 15 sec Feeds: Feed rate - fine adjustment 2 ~ 4000 mm/min Rapid traverse X-axis 6,000 mm/min Rapid traverse Y-axis 6,000 mm/min Rapid traverse Z-axis 5,000 mm/min Total power requirement 15 kW Machine weight approx. 3.6 t Dimensions approx. 3.4 x 3.6 x 2.2 m Tool Milling Machine - Universa ...

Height 1950 Width 1300 mm Length 3000 mm Voltage Electrical: 400V 50Hz 3N Installed Power 45 kw Main material Stainlees Steel Throat Diameter 180 mm Feeding System Hooper Throat Material Stainless Steel

Two Roll Mill 1m wide Hydraulic Nips With motor and gearbox AEG motor, 380volts, 107amps, 55kw, 1475rpm, 50 cycles Unidrive Gearbox manuf: Santasalo, Type 3KSV70, Year 1977, Weight 1500kg Lunn Safety gear fitted front and back of Mill Complete with control panel All mounted on a one piece bedplate Compact

Material : Stainless steel Drive: 30 KW Volume: 1200 ltr. - incl. control cabinet; --> Mixer with drive mounted on base frame.

Material : Stainless steel Dimensions: L 4.40 m x W 3.50 m x H 5.00 m --> Complete mixing tower in stainless steel version: --> with plough charmer : Manufacturer: MINOX Type: PSM 2000 / 3 MK Volume: 2000 ltr. Material : Stainless steel 3 x knife heads Main drive: 37 KW.

REALMECA MINI C3X-CNC VERTICAL 1 phase machining milling machine Used for teaching begginers. Perfect condition

5 axis machininng center (milling/turning from bar) multitasking Under power in our warehouse MAKE CHIRON MODEL MILL 800 5 axis CNC Fanuc 18iMBS (5 simoultaneous axis 1) X, Y, Z (mm) 800 ? 500 - 550 Rapids (Highspeed) 60 m/min Swivelling head CNC controlled (B axis) +/- 100° Turning spindle Peiseler Milling spindle 12.000 giri / 140 Nm (v nota 2) Tools 65 Tool type HSK-A 63 DIN 69893 Tool-change time 1,5 sec (v nota 3) Table 1400x500 Max table load 1200 kgs Coolant through spindle 70 bar (see note 4) CNC controlled clamping/rotating unit for 6th face machining (v. nota 5) Pressurised linear encoders Swarf conveyor Renishaw-ready Y.O.M. 2006 Weight 7500 kgs Turning package Max dia 65mm RPM: 15 / 4500 Max 42,5 KW / 90 Nm. Hydraulic clamping 800 Nm. Bar loader ILS-RBK- 10012 65 Diameters min ...

The Hot Strip Mill at JFE Steel’s Keihin district stands as a testament to cutting-edge steel production technology, boasting the capability to manufacture Japan's widest hot-rolled steel strip. Commissioned in 1979, the mill has been continually upgraded throughout the years to maintain its competitive edge. Production ceased in September 2023, leaving behind a legacy of excellence. It features a Pair Cross Shift Mill for adaptive roll gap control to optimize thickness and shape. A key enhancement was the integration of a Sizing Press in 2009, which allows for variable strip widths while using slabs of constant width. This not only increases the productivity of the slab caster and reheating furnace upstream but also expands the range of products that can be manufactured efficiently. Capable of rolling slabs measuring up to 2,300 mm in width, with thicknesses ranging from 160 t ...

Originally commissioned in the 1980s, the Tandem Cold Mill at JFE Steel's Keihin plant undegone a significant modernization in 2007 to meet high standards. Upgraded with a state-of-the-art pickling line and carrousel tension reel, the 5-stand PLTCM integrates advanced technologies from industry leaders Mitsubishi, Hitachi, and IHI, enhancing the system’s reliability, productivity, and quality control. Make: MITSUBISHI-HITACHI-IHI Year of manufacture: 2007 (integrated to TCM from 1980s) Mothballed since: Ceased production in March 2019 Production capacity: 1,200,000 tons per year Rolling direction: Right to left (right hand line) Processed material: Low carbon steel Strip width: 600 – 1,350 mm Strip thickness: 1.8 - 4.5 mm entry 0.12 – 1.6 mm exit Coil weight: max. 32,000 kg entry max. 45,000 kg exit Line speed: 250 mpm PL section  ...

Mixer meat 70 liter, NEW Capacity: 35kg Dimensions: 78x61x74cm Power: 2.2kW

55,000 litre milk tank/ agitator tank made of V2A Cat No.: 25-0151EUBA Condition: Used Volume 55000 L Material V2A (AISI 304) 1.4301 Overall height 8400 mm Cylinder height 6000 mm Diameter 3400 mm Number of feet 3 Surface marbled on the outside Surface inside 2B=IIIC ground Agitator Erwin Stelzer Warburg Agitator Technology Topsoil: Clapper bottom Level measurement with sleeve 3/4" Side stick agitator mixer with 2 propeller stages Dome with manhole Ø DN 300 Tank cylinder: Manhole Subsoil: Clapper bottom Sensor for level measurement 3 half-shell feet with base plate Fixed Technical data stick mixer: Manufacturer: Erwin Stelzer Warburg Rührwerktechnik Engine type: DRK 7.127 6.0 kW 8.0 hp 390/660 volts 18.2/10.5 Amp. 0.68cosφ 450 r.p.m. 50 Per. Operating Mode: S1 Agitator shaft: 6,870 Propeller: 2 x 500

Meat mixer Sind 120 liter, NEW Dimensions: 860x510x1100 cm Power: 1,5 KW

Plough-charmed PSM 300 / 1 MK Material : Stainless steel Main drive: 7.5 KW Volume: 300 ltr.; Demonstration machine, 5 - 6 operating hours; --> food suitable. --> mixer available at short notice, price VHB. Facilities: - Mixing plant: ploughshares, - 1 knife head, drive: 4 KW; - Sack shakes, material: stainless steel; - Sack container buckle: at the outlet with manually operated rotary flap; - outlet height of the bagging device: 980 mm; - air flushing on the shaft passages; - Stainless steel control cabinet, fully wired -- > ready for operation; - Machine frame with pallet space, made entirely of stainless steel;

Year of manufacture 2019, top condition, only approx. 300 hours Machine housing: solid stainless 2 rotation directions Emptying by hydraulic tilting of the mixing trough Membrane keyboard with plain text display in German Automatic mixing time preselection Control cabinet built-in, main switch Microprocessor Control (PLC) Mixing speed speed: infinitely variable Mixing tank: 500 litres Motor power 7.5 KW / voltage 400V / 50Hz Incl. MA 20 automatic mixing: for up to 20 programs (forward/backward/pause/total time and mixing speed speed) Incl. Z-mixing arms instead of paddle shafts Incl. protective grille: welded construction made of stainless steel, hydraulically operated Incl. 2 operating instructions with machine With mast feeding system BA24 Hydr., stainless, for standard wagons

Contec Mini 15 - Concrete mixing plant Mixer M 500/300 liter Capacity 4 - 9 m3 Aggregate hoppers: 2 x 2.5 m3 on a stable metal frame Belts: 2 belts integrated and attached to the aggregate hoppers

Originates from a European pharmaceutical leader in contract development and manufacturing (CDMO). Includes: 304 s/s platforms and stairs The MGW-1 used process mixer is designed for preparing alcohol, alcohol-based or water-based solutions, storing them, and maintaining the temperature of the medium at the level necessary for further processing. Working Description: Milfor is currently a part of Schwarte Processing – a brand of the HF FoodTech Group Web: abc.schwarte-processing.com The device is made to ATEX standard and can operate zone classified as explosion-hazard zone standard Z1 and Z2. The mixer is designed as a vertical cylindrical tank with a working capacity of 1000L and an internal diameter of 1100mm, ellipsoidal bottom. The tank is a welded, double-shell structure made of 316L stainless steel (components in co ...

Unused carbon steel double ribbon mixer, 5500 L volume. Chamber dimensions: 4000x1600x1000 mm. Working volume 2500-3000 L. 3 triggers closed pneumatically or manually (pneumatic elements not fitted) 70 mm shaft. Engines used 9 and 11 kW. New gears. Rotation speed approx. 30x / min.

This mixer is used but has been cleaned and tested This HL662-1STD is ideal for commercial kitchens thanks to its 60 qt. bowl, stainless steel bowl guard, and dough hook. With an ergonomic design and superior functionality, you can make repeat recipes consistently and create new ones with ease and efficiency. This unit requires a 200/240V electrical connection for operation. Ergonomic Swing-Out Bowl Featuring an ergonomic swing-out bowl, this mixer makes it easy to load and unload ingredients. With a single point bowl installation, you can easy mount or remove the bowl as needed. Plus, the bowl interlock ensures that the mixer bowl is properly in place before the mixer will operate for added safety. Dough Hook This mixer comes with a (1) "ED" dough hook so you can mix up to 90 lb. of dough at once. The 2.7hp motor, gear transmission, and safety mechanism system provide plenty  ...

KAAST Millex VPlus 7 CNC machining Centre way back in 2011 complete with Siemens Controller 802S

Mobile ring trough mixer with 2 exchangeable mixing blades and 1 exchangeable side scraper for mixing smaller quantities of concrete.

It is a new V MIX 100 planetary stirring machine (max. 100 liters) for sale. specifications: - Continuous speed change - inverter control - Programming 20 mix recipes - Programming the mixing time - Automatic lifting of the bowl - incl. 3 x tools - incl. 1 x boiler (100 liters) - 12-month warranty A video can be sent on request. Price on request.

Hammer mill Mikropul Cologne Type 3SCB Serial number: 610098002 Year of construction: 1979 Electric motor 30 to 75 Kw can be used Height: 1200 mm Width: 1200 mm Depth: 1000 mm Inlet: 170 mm x 170 mm Outlet diameter: approx. 500 mm Roller: 400 mm x 350 mm Changes and errors in the technical data, data and prices as well as intermediate sale reserved.

Mixing Grinder 130 mm hole plate diameter Throughput depending on material type, speed, and cutting set Capacity: up to 3.000 kg/h Main motor power: 8.5 KW Power supply: 380 V, 50 Hz Dimensions of the machine in cm: Width: 80 Length: 130 Height: 130 Hopper capacity approx 150 liters (mixing capacity depending on meat up to 100 kg) Worm, worm housing, and closing are completely stainless Delivery time: after advanced payment machine is generally refurbished and ready for delivery

Number of milling spindles: 2 St. fence: 1 ja workpiece: ja The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 500 mm y-travel: 500 mm z-travel: 350 mm table surface area: 800 x 450 mm spindle taper: ISO: 40 quill stroke: mm feed - longitudinal/cross: mm/min feeds vertical: mm/min turning speed range: max. 3150 U/min voltage: 380 V / 50 Hz power capacity: 4 kW weight of the machine ca.: 1,7 t dimensions of the machine ca.: 2,5 x 2,3 x 2,0 m • HEIDENHAIN TNC 155 - control, • with electrical hand wheel, • several tool tapers, • new set of bevel gears, The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 800 mm y-travel: 500 mm z-travel: 460 mm table surface area: 1000 x 500 mm spindle taper: SK 40 control: HEIDENHAIN TNC 150 spindle turning speed range: 31,5 - 3150 U/min feeds longditudinal/cross/vertical: 1 - 3000 mm/min rapid traverse longitudinal and cross: 6 m/min rapid traverse vertical: 4 m/min quill stroke: 110 mm distance spindle nose and table: max. 559 mm table load capacity: max. 500 kg total power requirement: 14 kW weight of the machine ca.: 3,1 t dimensions of machine L x W x H: 2,15 x 1,8 x 2,15 m Accessories: vertical head with hydr. tool clamping and quill retraction, solid table, coolant The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hydraulic power pack, hydraulic pump, hydraulic pump, universal power pack -Manufacturer: Orsta, universal unit -Motor: 1.1 kW/1410 rpm -Nominal pressure: 63 bar -Liter output: 6.3 l/min -Hydraulic tank/filter/valves: see pictures -Dimensions: 380/750/H640 mm -Weight: 72 kg

x-travel: 800 mm y-travel: 500 mm z-travel: mm Control: Heidenhain tool taper: SK 40 : 13,5 kw turning speeds: 3150 U/min total power requirement: kW weight of the machine ca.: 3 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

ALL STAINLESS STEEL Hopper capacity : 300 l Two levels of hopper Two working shafts with paddles Front discharge of ready product in 200 l trolley Programming controller Power – 4 kW Machine dimensions in cm: Width: 95,0 Length: 154,0 Height: 156,0 Weight - 500 kg OPTION :Loading unit 200l trolleys: Column loader dimensions in cm: Width: 110,0 Length: 120,0 Height: 238,0 Column loader power 0,8 kW

Type: S 300 l 2P-V Complete stainless steel Hopper capacity 300 liter Double working shafts Rotation of shafts in both directions Vacuum: 0,04 – 0,06 mpa Electric power: 4.4 kW Voltage: 380 V / 50 Hz Discharging pneumatic flaps PLC + Touchscreen control Delay start 99 programs Installation dimensions of machine in cm: Width: 135 Lenght: 84 Height: 142 Delivery time: after advanced payment, one working day

Type: S 500 l 2P-V Complete stainless steel Hopper capacity 500 liter Double working shafts Rotation of shafts in both directions Vacuum: 0,04 – 0,06 mpa Electric power: 5.6 kW Voltage: 380 V / 50 Hz Discharging pneumatic flaps PLC + Touchscreen control Delay start 99 programs Installation dimensions of the machine in cm: Width: 160 Lenght: 95 Height: 142 Delivery time: after advanced payment, one working day

Type: S 200 l 2P Complete stainless steel Hopper capacity 200 liter Double working shafts with paddles Rotation of shafts in both directions Protection cover Two motors and two gears, transmission chain Electric power: 1.5 kW + 1.5 kW Voltage: 380 V / 50 Hz Discharging: 2 flaps Installation dimensions of machine in cm: Width: 120 Lenght: 65 Height: 100 Delivery time: after advanced payment, one working day